$1000 - $2000

4021 RAM 4021 Respiratory Air Monitor, Carbon Monoxide (CO) by GfG

The RAM 4021 AutoCal® series is the unit of choice where specific and accurate measurement of carbon monoxide, oxygen or dew-point levels are required. Designed to meet OSHA requirements for monitoring of Grade D respirable air, this unit is equipped with a reliable electrochemical sensor that accurately indicates the level of carbon monoxide on an illuminated liquid crystal display. Adding versatility, this unit offers optional oxygen or dew point sensors for applications where detection or measurement is needed.

Calibration and maintenance are simple with our innovative AutoCal® system. Additional features including alarm relay contacts, user adjustable alarm point, low flow alarm indicator and many more make this unit an intelligent choice. The RAM 4021 is available in four models, the 4021 (CO), 4021-1 (CO and O2), 4021-DPX (CO and dew point levels) and 4021-PR (CO and additional relay to signal power loss to monitor, complies with newest NFPA regulation). All models may be purchased with or without airline filter systems

Respiratory air specifications

All GfG Instrumentation RAM Instruments satisfy the requirements of OSHA rule 29 CFR 1910.134 (d) (2) (ii) for carbon monoxide monitoring. They will also monitor Grade E air, generally specified for breathing air in cylinders (SCBA).

Wall mounted filter panel option

The 25, 50 and 100 CFM panels filter out dangerous toxins from supplied air sources and ensure clean, breathable air. The threestage filter system efficiently removes particulates, oil vapors and hydrocarbons from an air supply. After filtration, the regulator sets the pressure for the respiratory equipment and the manifold assembly provides multiple outlets for airline hose quick connections. The model 8025 panel includes two user female quick connect outlets; the 8050 includes four, and the 8100 includes eight. A 1/2" FPT connection is standard on all 50 and 100 CFM panels, and a 3/8" FPT connection is standard on all 25 CFM panels.

Features

• Continuous compressed air CO monitor
• Integrated dew point measurement
• Robust easy-to-operate design

Features

• RAM 4021 Monitor
• Carbon monoxide (CO) sensor
• Other sensors (as specified)
• Manual

123-H2S Gasflag Hydrogen Sulfide, 0-25ppm by Crowcon

Gasflag is a control system for monitoring any 4-20mA flammable, toxic or oxygen gas detector. Gasflag is ideally suited to light industrial or commercial applications such as LPG monitoring on garage forecourts, chlorine detection in swimming pool dosing rooms, or methane detection in boiler rooms.

Gasflag features a loud sounder, bright LED indicators and relays for switching external devices such as audible visual alarms or valves.

Easy and safe to use - Bright alarm annunciator

• Loud internal audible alarm
• Clear sytem intergrity indication

Fully Flexible

• Accepts industry standard 4-20mA inputs
• Multiple units can be daisy chained
• Variable alarm configurations

No hidden costs

• Integral alarm outputs
• Simple installation
• Minimum maintenance
• One button operation

123-HF Gasflag Hydrogen Fluoride, 0-10ppm by Crowcon

Gasflag is a control system for monitoring any 4-20mA flammable, toxic or oxygen gas detector. Gasflag is ideally suited to light industrial or commercial applications such as LPG monitoring on garage forecourts, chlorine detection in swimming pool dosing rooms, or methane detection in boiler rooms.

Gasflag features a loud sounder, bright LED indicators and relays for switching external devices such as audible visual alarms or valves.

Easy and safe to use - Bright alarm annunciator

• Loud internal audible alarm
• Clear sytem intergrity indication

Fully Flexible

• Accepts industry standard 4-20mA inputs
• Multiple units can be daisy chained
• Variable alarm configurations

No hidden costs

• Integral alarm outputs
• Simple installation
• Minimum maintenance
• One button operation

VPE-GN Professional Kit by Superior AccuTrak

The Patented Superior AccuTrak® VPE-GN Gooseneck represents state-of-the-art technology for pinpointing leaks in air conditioning and refrigeration systems. The new 9½ flexible Gooseneck provides better detection in hard-to-reach places, and is great for automotive applications too. AccuTrak® is extremely sensitive to the ultrasonic sound of a turbulent gas leak. Using the latest "heterodyning" technology it translates the sound to a lower frequency which your ear can interpret. The VPE-GN maintains the original sound characteristics making it possible to distinguish leaks from other competing background sounds. AccuTrak® is so sensitive you can actually hear the blink of an eye, yet most background noise will not interfere with detection accuracy. Like all Superior AccuTrak® instruments, the VPE-GN easily detects leaks of ANY gas or refrigerant, compressed air, and even vacuum leaks.

The AccuTrak® VPE-GN Professional Kit is designed for technicians who work in noisy places, or who regularly need to find smaller leaks. With the sensor at the end of the 9-1/2 long flexible GooseNeck you get full sensitivity all the way into those hard-to-reach places. The VPE-GN Professional Kit includes all the great features of our VPE-GN Standard Kit upgraded with professional Noise Cancelling Headphones and a larger case to keep everything together. These high quality headphones eliminate all background noise, allowing a technician to effectively find the smallest leaks even in very loud environments. You can choose the standard style professional headphones, or the hardhat compatible version same price!

Kit Includes:

• VPE-GN Leak Detector
• Battery
• Waveguide
• Noise Blocking Headphones
• Large Carry Case

Applications:

• Leak Detection: Air, Vacuum, Refrigerants; ANY GAS!
• Steam Traps: Detect live steam loss in seconds!
• Valves: Detect/hear internal leakage in check, ball, needle, gate or any type of valve! Diagnose thermal expansion valves in just five minutes!
• Bearing Wear: Hear wear and lubrication problems before damage is done!

Features:

• Gooseneck Configuration: allows operator to get accurate readings in hard to reach places.
• Audio Output: 0 Hz to 4 kHz Natural Sound conversion allows you to Hear the Leak, and distinguish leaks from mechanical or other background ultrasound.
• Visual Output: 10 element bar graph provides quick and intuitive visual indication to presence of and relative strength of ultrasound.
• Adjustable Sensitivity: allows operator to quickly identify leaks from a distance, and then zero in on the exact location of the leak.

Capabilities:

• Capable of detecting a 5 psi leak out of a 0.005" (5/1000 inch) hole, 20 to 30 feet away depending on background noise.
• Easily detects any gas that generates ultrasonic sound during flow including vacuum leaks.
• Capable of detecting leaks equivalent to 1.5 oz/year of Refrigerant.
• Works equally well for compressed Air or Nitrogen.
• Not affected by wind or high concentrations of leaked gas or refrigerant.

Kits for Every Application

Whether you only need the basic functions of the VPE-GN or you plan to take full advantage of the instrument's diverse capabilities, we have a kit that will meet your needs! Click the "Find Your Kit" tab above to learn more.

Advantages Versus Sniffers

• AccuTrak® VPE is a much more accurate and reliable instrument for detecting single and multiple leaks.
• AccuTrak® VPE can detect any type of refrigerant gas including nitrogen.
• AccuTrak® VPE detects both vacuum and pressure leaks.
• AccuTrak® VPE is effective in gas saturated areas and under windy conditions.
• AccuTrak® VPE does not require the introduction of tracer gases into the system, which can be ozone depleting when vented, and can also be harmful to ones health.
• AccuTrak® VPE is battery powered for cordless operation

Advantages versus other Ultrasonic Leak Detectors

• AccuTrak® VPE is #1 in technology. We wrote the book on ultrasonic leak detection, our patented instruments lead the industry!
• AccuTrak® VPE is the original! it is not a copy.
• AccuTrak® VPE is the most durable unit available, with the best warranty. The face of the unit is sealed with no pin holes/speakers for foreign objects to enter.
• AccuTrak® VPE has more dynamic range, and wont overload in loud areas.
• AccuTrak® VPE gives true audio sound reproduction instead of the "beeps and squeals" of other instruments.

Gasman Personal Gas Monitor

For over 40 years, Crowcon Detection Instruments has produced state of the art gas detection devices for personal and industrial use. Building upon their reputation for reliable and innovative gas monitoring products, Crowcon introduces the Gasman personal gas monitor. Its lightweight and compact design is convenient for jobsites where workers need not be weighed down by excessive bulk and equipment. The unit conveniently clips to a pocket or helmet and operates continuously.

The Gasman personal gas monitor has numerous convenient features such as:

• One button technology
• Backlit LCD display
• Durable polycarbonate casing
• Quick response triple alert system
• Compact and lightweight design

Easy to Use

The Gasman s true one button technology is an ideal and simple design. The large glove friendly button is mounted on the front of the unit for easy access and controls all of the unit s programmable features. Also on the front, the Gasman s easy to read backlit LCD screen indicates gas readings and the battery status. The simple screen provides a clear indication of the unit s operation status. It will also alert the user 30 days in advance of when a calibration test is due. With a simple and intuitive design, Crowcon has produced a gas detector that reduces the complexities of workplace safety, and ensures workers in a straightforward manner that their equipment is on and operational.

Triple Alarm System

This portable single gas detection system features a triple alarm system that is sure to alert the user and anyone in the vicinity. The visible alarm utilizes a dual red and blue flashing LED light, and the unit houses an internal vibrating alert system. These two indicators allow for visual recognition in loud environments and working conditions. The alarm system also features a programmable audible alarm at 95 decibels. The unit is capable of a variety of alarm tones, and users can select which tone may be best for the individual workplace setting. The triple alarm system with multiple sensory indicators is sure to be noticed in almost any work environment.

Specifications

The Gasman single gas monitor is lightweight and compact, weighing less than 135 grams and with dimensions of 90 x 48 x 24 mm. The unit is available with a wide variety of gas sensors which feature various detection and alarm levels. The unit also features a quick response time of 20 seconds for flammable and toxic gases or 10 seconds for oxygen. Its datalogging feature has approximately 900 hours of storage and all events are time stamped. The battery life for this unit is incredible with 12 hours of runtime on a rechargeable battery or up to 2 years on a non-rechargeable battery.

2350-300 EC 35 Fixed Gas Transmitter by GfG

Remote Transmitters for Oxygen and Toxic Gases

The EC 30 is an advanced transmitter for the detection of toxic gases and oxygen levels. This smart area monitor has an aluminum explosion proof housing with a stainless steel sensor cover that makes the EC 30 series suitable for the harshest environments.

Simple and effective

Once you power up the units, they will accurately display values on the large LCD and transmit a linear 4-20 mA signal to any GfG controller. AutoCal automatic calibration and maintenance is done effortlessly through push buttons or via a digital remote control connection. Smart sensors allow the user to easily change ranges or gas types in the field without a need for additional programming. The EC 36 is equipped with onboard relays for two alarm points and one sensor fault for local connection and activation or deactivation of external devices like alarms, fans, auto dialers etc.

Digital display / control connection

The digital connection allows display of readings, non-intrusive maintenance and AutoCal calibration activation to be done locally or from a distance.

Features

• Robust industrial design
• Fully-automatic one button calibration adjustment

S01-3000-210 ProRAE Guardian Real-time Monitoring Tier 3 Yearly Subscription per Instrument by RAE Systems

The Subscription Model provides the end customers the ability to get license keys that are valid for a fixed duration of time or to allow rental houses to get license keys to lease out the software to their end customers for a fixed duration of time. Subscription based licenses cannot be combined with perpetual licenses.

2313002-1 2 - GMA 313 Stand-Alone System, Basic Set for Two Room Monitoring by GfG

State of the Art Technology

The best solution for CO2 monitoring fromthe specialists in gas detection. The GMA 313 indicates a gas hazard immediately and reliably. The built-in alarm LED and loud horn provide a warning before entering the room. The external alarm GMA 313 EQ also gives a warning wherever you want it, e.g. at the stairway or at the bar. The GMA 313 offers state-of-the-art sensor and microprocessor technology from a compact unit.

The sensor and electronics, horn and lights are integrated in one enclosure, thus saving installation costs. The robust casing is splashwater proof (IP 54), so splash-water cannot enter and damage the monitor. Thermostat control and temperature compensation of the sensor ensure reliable measurements and safety even in case of sudden temperature changes.

Low Maintenance and Long Lifetime

The infrared (NDIR) sensor has a considerably longer lifetime than an electrochemical CO2 sensor. The GMA 313 is low maintenance, robust, and reliable. Installation of the GMA 313 is very simple, just plug it into a standard 110 v ac wall outlet.

Infrared Principle

Carbon dioxide (CO2) absorbs light in the infrared range of the spectral. The NDIR technology of GfG's sensor detects the carbon dioxide concentration precisely and reliably. The infrared light emitted by a lamp passes through the gas sample. Carbon Dioxide absorbs the light in a narrow spectral range.

The remaining light is measured at the detector. The difference between emitted and detected light is proportional to the gas concentration. Water vapor and other gases, which may be presenting the sensor chamber, do not affect the light absorption in this spectral range.

Safe detection results, even with temperature changes. Precise optical measurement ensures the best accuracy and repeatability. The IR principle is as distinct as a fingerprint in criminology.

This means that only carbon dioxide is detected, thus eliminating false alarms from interfering gases. GfG Products use electronics with voltage stabilization and temperature compensation.

This results in stable measurement vales even with considerable temperature variations.

The GMA 313 has no moving parts which could be subject to wear and tear. This ensures a long lifetime and reduced service requirements. Permanent self-check of functional capability provides additional safety. Sensor and electronics are protected by a robust enclosure (IP 54).

3506-050 EC 35 Fixed Gas Transmitter, Nitrogen Dioxide (NO2), Display by GfG

Remote Transmitters for Oxygen and Toxic Gases

The EC 30 is an advanced transmitter for the detection of toxic gases and oxygen levels. This smart area monitor has an aluminum explosion proof housing with a stainless steel sensor cover that makes the EC 30 series suitable for the harshest environments.

Simple and effective

Once you power up the units, they will accurately display values on the large LCD and transmit a linear 4-20 mA signal to any GfG controller. AutoCal automatic calibration and maintenance is done effortlessly through push buttons or via a digital remote control connection. Smart sensors allow the user to easily change ranges or gas types in the field without a need for additional programming. The EC 36 is equipped with onboard relays for two alarm points and one sensor fault for local connection and activation or deactivation of external devices like alarms, fans, auto dialers etc.

Digital display / control connection

The digital connection allows display of readings, non-intrusive maintenance and AutoCal calibration activation to be done locally or from a distance.

Features

• Robust industrial design
• Fully-automatic one button calibration adjustment

5601-3021 GDX-350 Gas Sensor Transmitter/Monitor, [H2S] 0-500 ppm, 2-wire by Bacharach

Bacharach's new state-of-the-art GDX-350 transmitters, with Smart Sensor technology, provide accurate and continuous detection of toxic, combustible and asphyxiate gases. The full-featured design of the GDX-350 includes a large LCD display, a 4-20 mA interface, programmable alarms, optional relays and a Modbus interface. Exclusive pre-calibrated replacement sensor technology makes occasional maintenance practically effortless. Rugged construction, intrinsic safety capability (in two-wire mode with barrier) and an explosion-proof housing allow the GDX-350 to operate directly in hazardous-rated areas of many industrial environments, delivering reliable, superior-sensing performance to protect human life, equipment and property.

With its large LCD display, the GDX-350 shows gas concentrations, engineering units and bar graphs along with the most recent 30 minutes of trend data. Utilizing the on-board magnetic keypad, users can also navigate through the display to change alarm set points, instrument configurations, or enter into maintenance mode for non-intrusive sensor calibration. For security, menu options also enable the selection of an authorization code to lock critical parameters. Accompanying the LCD display are standard LED alarm indicators that show when low and high alarm conditions are met. An optional relay board is available to provide three 5-amp relays that can be used to drive audible/visual alarms, or activate exhaust fans.

Features & Benefits:

• Pre-calibrated Smart Sensor capability with 'plug-n-play' convenience minimizes maintenance and downtime
• Non-Dispersive Infrared (NDIR), Catalytic Bead and Electrochemical sensor options available
• Can be placed directly in hazardous environments where leaks occur for quick detection and rapid response
• Graphic LCD for real-time monitoring of concentrations
• 4-20 mA, optional Modbus RTU® and wireless interface
• Easily update alarm set points, configurations or maintenance modes using the LCD display
• 30-minute onboard data trend

M020-11212-131 QR3/Pump/CSA/900M Wireless/LEL/CO/O2/SO2/Accessorie by RAE Systems

The QRAE 3 is a full featured compact 4-gas monitor that provides detection and monitoring of Oxygen (O2), Combustibles and toxic gases that include Carbon Monoxide (CO), Hydrogen Sulfide (H2S), Sulfure Dioxide (SO2) and Hydrogen Cyanide (HCN) and others.

QRAE 3 can deliver wireless real-time instrument readings and alarm status 24/7. This provides better incident visibility and can improve response time.

Monitor-only configuration includes

• Monitor as specified
• Sensors as specified
• Sampling option as specified
• Calibration adapter (diffusion model only)
• T Calibration tube (pumped model only)
• Internal filters (mounted - diffusion model only)
• External filters (one mounted plus pack of 3 - pumped model only)
• Travel charger cradle with computer cable
• Lithium-ion battery pack
• Universal wall adapter
• CD ROM with ProRAE Studio II
• CD ROM with product content
• Quick Reference Guide

Key Features

• Available in Diffusion or Pumped version
• IP-65/67 water and dust resistant case
• Strong, protective, concussion-proof design
• Real-time gas concentration readings and alarm status enabled by state-of-the-art wireless technology
• Unmistakable five-way local and remote wireless notification of alarm conditions
• Large graphical display icon-driven user interface through intuitive, simple-to-operate two-button user interface
• Multi-language support: 18 languages encoded
• Easy access to pump, sensors, filter and battery compartment

Applications

• Industrial safety
• Oil and gas
• Fireground "Toxic Twins" detection
• Environmental
• Fire and Emergency response
• Chemical
• Pharmaceutical
• Telecommunications

SPLIF6BMXCNUZZ Sensepoint XRL Fixed Point Gas Leak Detector, Bluetooth, cULus, CH4 100%LEL, Modbus, Charcoal Grey by Honeywell Analytics

Sensepoint XRL is a fixed point gas leak detector that is designed to meet the needs of industrial applications. With over 50 years experience in gas leak detection, Honeywell offers a flexible range of highly-reliable sensing devices to meet those needs.

• Quick installation
• Rapid configuration
• Simple to operate
• Straightforward to maintain

Honeywell innovation enables customers to pair the gas detector with their mobile phone, and then use an app to perform many tasks related to installation, commissioning and maintenance.

Flexible Output Options

Sensepoint XRL is available with either mA loop analog output or Modbus RTU. The result is a flexible solution that can easily be incorporated into legacy systems as well as new installations.

Easy Control and Maintenance

Sensepoint XRL's smartphone interface makes for much faster calibration, configuration and bump tests. Inspecting the status and settings of individual Sensepoint XRL detectors is simple. Use the mobile app to:

• Read gas concentrations in real-time
• Reconfigure settings
• Check unit histories

Automated Reporting

Increase the efficiency of your operations and reduce administration time. The app and Sensepoint XRL provides easy access to diagnostic information and generates calibration reports at the touch of a screen.

Compatible System Controller

Touchpoint Plus is the perfect complement to Sensepoint XRL, providing an intuitive, easy to operate gas detection solution to meet the needs of your business.

Visual Integration

Clean aesthetics and a choice of colors mean that the detector appearance can be selected to compare or contrast with the environment in which it is being used.

Typical Applications

• Manufacturing facilities and factories
• Water treatment plants
• Battery charging facilities
• Vehicle test facilities
• Petrochemical plants
• Fuelling depots

Accessories

• Calibration cap
• Collecting cone
• Pole Mount Bracket Kit
• Duct Mount Kit
• Weather Protection
• Flow Housing

FEATURES & BENEFITS

• Choose from a range of mA or Modbus output versions for flexible system design to meet the customers requirements.
• Selectable source or sink current for analog output enables one detector to be suitable for both system configurations.
• The ingress protection of NEMA 4X/IP66 allows units to be installed in outdoor environemtns.
• Simplified maintenance with familiar smartphone technology saves money and time.
• Multi-color visual indicator to show status makes it easier to know the detector status immediately and identify detectors that require attention or are warning of danger.
• Manage the detector without making a physical connection. Remove the need for physical access to hard-to-reach devices.
• One person calibration without the need to open the detector. Saves time and removes need for hot work permit.

2492013 IR 24 Fixed Gas Transmitter Carbon Dioxide (CO2), 0-25% Vol. by GfG

CO2 a toxic hazard

Carbon dioxide (CO2) is often used as a work medium, or is stored, shipped, or generated as a by-product of certain industrial applications. The specific characteristics of CO2 make this gas a hidden danger.

Carbon dioxide is odorless, tasteless, and undetectable to human senses. CO2 is considerably heavier than air and can rapidly build to dangerous concentra-tions in holes, sewers, or cellars. Concentrations as low as 4 percent volume can be toxic, and 8 percent volume CO2 can cause death. Carbon dioxide also displaces the oxygen content in the ambient air, which may lead to asphyxiation.

GfG Instrumentation's fixed gas warning systems allow continuous monitoring of gas hazards to ensure that countermeasures can be taken in time. A fixed gas monitoring system consists of a remote sensor which is connected by a cable to a controller such as the GMA 011, GMA 100, or GMA 300. The controller powers the remote sensor and evaluates its measurement signals.

IR24 for CO2

The remote sensor with its sensor cell is mainly responsible for the reliability of a gas monitoring system. The sensor is installed wherever CO2 may be present. Even the lowest gas concentrations can be detected and transmitted to a central control station as current or voltage signals which are proportional to the actual gas concentration.

IR24 detection principle: infrared light

Since carbon dioxide (CO2) absorbs light in the infrared spectral range, the NDIR method used in the GfG sensor can measure the carbon dioxide concentration precisely and reliably. Infrared light is sent through the sensor chamber. Carbon dioxide absorbs a part of this light in a narrow spectral range, and the remaining light is measured at the detector. The difference between the light sent and received is propor-tional to the gas concentration. Water vapor or other gases that can be present in the sensor chamber do not affect the light absorption in this spectrum band.

Durable construction for long lifetime

The IR24 does not contain any moving parts that are subject to wear and tear, ensuring a long lifetime, and low maintenance costs. More safety is provided by the permanent self-check and function test of the GMA controller. Sensor and electronics are protected in a solid enclosure from dust and water according to IP 54. This ensures that water cannot enter the detector, even in wet environments.

Easy handling

Behind a service lid on the front of the IR 24 are potentiometers and test connectors for easy adjustment of zero point and detection range. This allows one-person calibration on-site and reduces service down-time.

Quality control adds more safety

All remote sensors are made by GfG Instrumentation and have to pass a 100% quality and function test. All sensors are shipped pre-calibrated. An authorized GfG Instrumentation specialist makes the final adjustments during system installation.

IR 24 features

• Selective NDIR detection principle
• Extended sensor life for long-term economy
• Easy handling
• Signal output either 0.2 1 mA or 4 20 mA
• Potentiometers for easy adjustment of zero point and detection range
• Connectors for test of output signal
• Solid aluminum casing, IP 54
• High reliability and repeatability of measurement results
• Wide detection range

M020-11111-111 QRAE 3 LEL / H2S / CO / O2 Multigas Monitor - Pumped, Accessories Kit by RAE Systems

The QRAE 3 is a full featured compact 4-gas monitor that provides detection and monitoring of Oxygen (O2), Combustibles and toxic gases that include Carbon Monoxide (CO), Hydrogen Sulfide (H2S), Sulfure Dioxide (SO2) and Hydrogen Cyanide (HCN) and others.

QRAE 3 can deliver wireless real-time instrument readings and alarm status 24/7. This provides better incident visibility and can improve response time.

Monitor-only configuration includes

• Monitor as specified
• Sensors as specified
• Sampling option as specified
• Calibration adapter (diffusion model only)
• T Calibration tube (pumped model only)
• Internal filters (mounted - diffusion model only)
• External filters (one mounted plus pack of 3 - pumped model only)
• Travel charger cradle with computer cable
• Lithium-ion battery pack
• Universal wall adapter
• CD ROM with ProRAE Studio II
• CD ROM with product content
• Quick Reference Guide

Key Features

• Available in Diffusion or Pumped version
• IP-65/67 water and dust resistant case
• Strong, protective, concussion-proof design
• Real-time gas concentration readings and alarm status enabled by state-of-the-art wireless technology
• Unmistakable five-way local and remote wireless notification of alarm conditions
• Large graphical display icon-driven user interface through intuitive, simple-to-operate two-button user interface
• Multi-language support: 18 languages encoded
• Easy access to pump, sensors, filter and battery compartment

Applications

• Industrial safety
• Oil and gas
• Fireground "Toxic Twins" detection
• Environmental
• Fire and Emergency response
• Chemical
• Pharmaceutical
• Telecommunications

2811-724-001 EC 28 Gas Transmitter with Sensor, Nitrogen Oxide (NO), No Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

3661-300 EC 36 Fixed Gas Transmitter, Nitrogen Oxide (NO), Display / Alarm Relays by GfG

Remote Transmitters for Oxygen and Toxic Gases

The EC 30 is an advanced transmitter for the detection of toxic gases and oxygen levels. This smart area monitor has an aluminum explosion proof housing with a stainless steel sensor cover that makes the EC 30 series suitable for the harshest environments.

Simple and effective

Once you power up the units, they will accurately display values on the large LCD and transmit a linear 4-20 mA signal to any GfG controller. AutoCal automatic calibration and maintenance is done effortlessly through push buttons or via a digital remote control connection. Smart sensors allow the user to easily change ranges or gas types in the field without a need for additional programming. The EC 36 is equipped with onboard relays for two alarm points and one sensor fault for local connection and activation or deactivation of external devices like alarms, fans, auto dialers etc.

Digital display / control connection

The digital connection allows display of readings, non-intrusive maintenance and AutoCal calibration activation to be done locally or from a distance.

Features

• Robust industrial design
• Fully-automatic one button calibration adjustment

VPE Plus Kit by Superior AccuTrak

The Patented Superior AccuTrak® VPE represents state-of-the-art technology for pinpointing leaks is air conditioning and refrigeration systems. AccuTrak® is extremely sensitive to the ultrasonic sound of a turbulent gas leak. Using a technology called "heterodyning" it translates the sound to a lower frequency which your ear can interpret. AccuTrak maintains the original sound characteristics making it possible to distinguish leaks from other competing background sounds. AccuTrak is so sensitive you can actually hear the blink of an eye, yet most background noise will not interfere with detection accuracy.

The AccuTrak® VPE Plus Kit is designed for technicians looking to take full advantage of all the VPE s many capabilities. The VPE Plus Kit includes everything in our Standard Kit PLUS our powerful Burst Tone Sound Generator! The sophisticated Burst Tone can artificially pressurize any vessel or space with ultrasonic sound, allowing a technician to quickly scan for leaks even where there is no actual pressure differential! The VPE Plus Kit is ideal for technicians who test refrigerator door and window seals, or any other non-pressurized seal or vessel. The VPE Plus Kit is also great for Energy Audits and Surveys, and finding air leaks and sources of air infiltration in homes, aircraft, ships, and buildings.

Kit Includes

• VPE Leak Detector
• Headset
• Battery
• Hard Case
• Touch Probe
• Waveguide
• Sound Generator

Applications:

• Leak Detection: Air, Vacuum, Refrigerants; ANY GAS!
• Steam Traps: Detect live steam loss in seconds!
• Valves: Detect/hear internal leakage in check, ball, needle, gate or any type of valve! Diagnose thermal expansion valves in just five minutes!
• Bearing Wear: Hear wear and lubrication problems before damage is done!

Features:

• Audio Output: 0 Hz to 4 kHz Natural Sound conversion allows you to Hear the Leak, and distinguish leaks from mechanical or other background ultrasound.
• Visual Output: 10 element bar graph provides quick and intuitive visual indication to presence of and relative strength of ultrasound.
• Adjustable Sensitivity: allows operator to quickly identify leaks from a distance, and then zero in on the exact location of the leak.

Capabilities:

• Capable of detecting a 5 psi leak out of a 0.005" (5/1000 inch) hole, 20 to 30 feet away depending on background noise.
• Easily detects any gas that generates ultrasonic sound during flow including vacuum leaks.
• Capable of detecting leaks equivalent to 1.5 oz/year of Refrigerant.
• Works equally well for compressed Air or Nitrogen.
• Not affected by wind or high concentrations of leaked gas or refrigerant.

Kits for Every Application

Whether you only need the basic functions of the VPE or you plan to take full advantage of the instrument's diverse capabilities, we have a kit that will meet your needs! Click the "Find Your Kit" tab above to learn more.

Advantages Versus Sniffers

• AccuTrak® VPE is a much more accurate and reliable instrument for detecting single and multiple leaks.
• AccuTrak® VPE can detect any type of refrigerant gas including nitrogen.
• AccuTrak® VPE detects both vacuum and pressure leaks.
• AccuTrak® VPE is effective in gas saturated areas and under windy conditions.
• AccuTrak® VPE does not require the introduction of tracer gases into the system, which can be ozone depleting when vented, and can also be harmful to ones health.
• AccuTrak® VPE is battery powered for cordless operation

Advantages versus other Ultrasonic Leak Detectors

• AccuTrak® VPE is #1 in technology. We wrote the book on ultrasonic leak detection, our patented instruments lead the industry!
• AccuTrak® VPE is the original! it is not a copy.
• AccuTrak® VPE is the most durable unit available, with the best warranty. The face of the unit is sealed with no pin holes/speakers for foreign objects to enter.
• AccuTrak® VPE has more dynamic range, and wont overload in loud areas.
• AccuTrak® VPE gives true audio sound reproduction instead of the "beeps and squeals" of other instruments.

TXgard and Flamgard Plus

With over 40 years of experience in gas detection technology and development, Crowcon Detection Instruments is pleased to present one of its most economical gas sensing devices. With its one man calibration system, life-long sensors, and simple parts replacement, the Txgard and Flamgard Plus range of detectors offer a reliable and cost efficient solution for most gas detection needs.

With its mission to protect people and plant from gas hazards, the newest line of gas detecting instruments include exclusive state of the art features including:

• Marine grade with stainless steel housing
• A wide range of reliable and advanced gas detecting sensors
• Flexible output options
• Optional relays for alarm and fault
• Quick response times
• Easy to read screen displays
• Easy to operate calibration methods
• Efficient and economical sensor and gas detection technology

Rugged, Reliable, and Flexible

The detector models are constructed to withstand the abuse of hazardous work environments. The TXgard and Flamgard Plus detectors use marine grade aluminum with a stainless steel sensor housing to ensure the safety and integrity of the equipment. The TXgard-IS+ is constructed of carbon-loaded nylon. The models also feature flexible output options including 2 or 3 wire formats, optional relays for alarm and fault, and 4-20mA current sink or source. Crowcon also has a wide variety of catalytic and electrochemical gas sensors to fit these models (currently offering more than 25 individual gas sensors).

Flamgard Plus and TXgardPlus Specifications

The Flamgard Plus and TXgard Plus models are similar in size (200 x 115 x 115 mm) and weight (2.2 kilograms). However, the Flamgard Plus utilizes a catalytic bead sensor and the TXgard Plus utilizes an electrochemical sensor. Both feature an ingress protection with an IP66 weatherproof cap and 2 x M20 x ½ NPT cable entries. These models feature optional relays of SPNO or SPNC contacts rated 30 Vdc 1A (non-inductive load) for Alarm 1 and fault for Alarm 2.

For easy reading, these models have a 3 digit backlit display with and LED status indicator. The magnetically operated buttons control the calibration method and the terminals are suited for up to 1.5 mm2 cable. Both models are suited for usage in hazardous zones 1 and 2.

TXgard IS+ and Specs

The TXgard IS+ is slightly smaller than the other two models and houses an electrochemical sensor type. It is approximately 160 x 123 x 92 mm in size and .7 kilograms in weight. This unit also features an IP66 weatherproof cap for ingress protection. The display is slightly smaller than the other two models, and offers a 2 line 16 character LCD screen. The calibration method is operated via front mounted push buttons, and its terminals are suited for up to 2.5 mm2 cables. This model is appropriate for hazardous zones 0, 1, and 2, and when connected via an isolation device, the TXgard IS+ is suited for hazardous zones 20, 21, and 22.

2492001 IR 24 Fixed Gas Transmitter Carbon Dioxide (CO2), 0-5% Vol. by GfG

CO2 a toxic hazard

Carbon dioxide (CO2) is often used as a work medium, or is stored, shipped, or generated as a by-product of certain industrial applications. The specific characteristics of CO2 make this gas a hidden danger.

Carbon dioxide is odorless, tasteless, and undetectable to human senses. CO2 is considerably heavier than air and can rapidly build to dangerous concentra-tions in holes, sewers, or cellars. Concentrations as low as 4 percent volume can be toxic, and 8 percent volume CO2 can cause death. Carbon dioxide also displaces the oxygen content in the ambient air, which may lead to asphyxiation.

GfG Instrumentation's fixed gas warning systems allow continuous monitoring of gas hazards to ensure that countermeasures can be taken in time. A fixed gas monitoring system consists of a remote sensor which is connected by a cable to a controller such as the GMA 011, GMA 100, or GMA 300. The controller powers the remote sensor and evaluates its measurement signals.

IR24 for CO2

The remote sensor with its sensor cell is mainly responsible for the reliability of a gas monitoring system. The sensor is installed wherever CO2 may be present. Even the lowest gas concentrations can be detected and transmitted to a central control station as current or voltage signals which are proportional to the actual gas concentration.

IR24 detection principle: infrared light

Since carbon dioxide (CO2) absorbs light in the infrared spectral range, the NDIR method used in the GfG sensor can measure the carbon dioxide concentration precisely and reliably. Infrared light is sent through the sensor chamber. Carbon dioxide absorbs a part of this light in a narrow spectral range, and the remaining light is measured at the detector. The difference between the light sent and received is propor-tional to the gas concentration. Water vapor or other gases that can be present in the sensor chamber do not affect the light absorption in this spectrum band.

Durable construction for long lifetime

The IR24 does not contain any moving parts that are subject to wear and tear, ensuring a long lifetime, and low maintenance costs. More safety is provided by the permanent self-check and function test of the GMA controller. Sensor and electronics are protected in a solid enclosure from dust and water according to IP 54. This ensures that water cannot enter the detector, even in wet environments.

Easy handling

Behind a service lid on the front of the IR 24 are potentiometers and test connectors for easy adjustment of zero point and detection range. This allows one-person calibration on-site and reduces service down-time.

Quality control adds more safety

All remote sensors are made by GfG Instrumentation and have to pass a 100% quality and function test. All sensors are shipped pre-calibrated. An authorized GfG Instrumentation specialist makes the final adjustments during system installation.

IR 24 features

• Selective NDIR detection principle
• Extended sensor life for long-term economy
• Easy handling
• Signal output either 0.2 1 mA or 4 20 mA
• Potentiometers for easy adjustment of zero point and detection range
• Connectors for test of output signal
• Solid aluminum casing, IP 54
• High reliability and repeatability of measurement results
• Wide detection range

VN01703 X-am 5800 Multi-Gas Detector with CATEX,H2S/CO-LC,O2,NIMH by Draeger

The X-am® 5800 multi-gas detector measures up to six gases and is equipped with a particularly shock-resistant CatEx sensor. With the Drager Gas Detection Connect software, it offers live data transmission and powerful asset management. Designed for personal monitoring, the X-am 5800 offers you the highest level of safety at a low cost of ownership.

Benefits

Powerful data analysis in the cloud

Safety and efficiency thanks to its networking capability: Transfer your recorded data directly and conveniently via Bluetooth® to a smartphone and from there to the backend of the Gas Detection Connect software. As an alternative, you can also transfer the data directly to the cloud with the X-dock test station. This way, you have secure access to your data and its analysis at any time and from anywhere – simply via your internet browser.

Comfortable asset management

With the X-am 5800 you can manage your fleet of equipment comfortably and efficiently in daily use. Save operating costs and time through fast tests by using the automatic test station X-dock with low gas consumption or a pure mechanical bump test station. Further advantages: powerful asset management via our smart software solution, convenient firmware updates in the X-dock, an optional RFID transponder and individual colour marking of the devices. Few, easy-to-replace spare parts – including the power supply – and sensors ensure that your devices remain operational for many years. Drager provides a 4-year manufacturer's warranty on the basic device. Existing, compatible accessories from its predecessor, the X-am® 2500/5000/5600 can continue to be used.

Tailor-made gas monitoring

Small and lightweight: The X-am 5800 is comfortable to wear and easy to use even with gloves on thanks to its large buttons. The display clearly shows important information such as gas readings, alarms and time. The green D-light indicates that the unit is ready for use. All this, plus the completely language-free icon based user interface, makes it pleasantly simple to use and familiarise yourself with. For your added safety, its oxygen channel has four alarm thresholds – real pre-alarms and main alarms for falling and rising concentrations. Approved for use in Ex zone 0, it has also been tested according to protection class IP 68.

Powerful sensors

The new CatEx sensor offers you even more advantages: readiness for calibration within seconds, extreme robustness against shocks and the measurement of flammable vapours – such as petrol, diesel and nonane. You can also set the measurement gas to methane, propane, hydrogen, and many other gases. The performance is complemented by Drager's simple cross calibration concept, in which the measurement gas, calibration gas and bump test gas can be specified individually. Upon testing, the X-am 5800 then takes over the necessary conversions. The sensor is target to meet the demanding requirements of the new IEC standard 60079-29-1 (International Electrotechnical Commission).

At the same time, the CatEx sensor is resistant to poisoning substances such as silicones and other harmful substances. This combination of properties is exceptional. With years of experience in sensor technology, Drager develops and produces the sensors itself, including the powerful and durable electrochemical sensors in the XXS format. Your advantage: sensors and device are perfectly matched to each other – saving you operating costs. We are currently developing a durable, power-saving infrared sensor to measure flammable gases and vapours and/or carbon dioxide, as well as a photo-ionisation detector sensor for measuring volatile organic compounds (VOCs). These can be used instead of the CatEx sensor.

Focus on sustainability

During the development of the X-am 5800, great importance was given to sustainability. The optimised Drager Sensors and the rechargeable power supply, which can be easily replaced with one screw, ensure it has a long service life. Almost all spare parts can be replaced by trained users, while all remaining parts can be repaired by Drager Service. Furthermore, existing accessories from the previous series can still be used. Environmental protection has also been taken into account in the technical documentation and packaging: Designed to save paper, when you order two or more units, we can reduce the number of instruction manuals supplied if you order the modular version. For your convenience, Drager also takes back old devices and ensures that they are recycled properly.