$1000 - $2000

65-2640RK-06 M2A Stand Alone Sensor / Transmitter with j-box, %LEL, 4-wire horn/strobe with red lens, Specify Calibration by RKI Instruments

The RKI M2A™ is a state-of-the-art transmitter that can operate as an independent, stand-alone monitor or as part of an integrated system. The M2A connects with an analog or digital signal to virtually any controller, PLC, or DCS. Setup procedures are simplified with user friendly push buttons and OLED menus. It utilizes a magnetic wand technique for performing non-intrusive calibration. The M2A provides an automatic zero drift correction feature, which results in more stable readings and reduces the need for adjustments due to sensor aging.

The housing of the M2A does not need to be opened for zeroing or calibration, making it unnecessary to declassify the area for routine maintenance. It is designed so that a complete field calibration can be performed by one person. Sensor construction is rated Class I, Div. 1 Groups B, C, D for flammables, CO, H2S, O2, and CO2, and Class I, Div. 2 for all other toxics.

The transmitter provides a 4-20 mA output in addition to a Modbus digital output. It also has two levels of alarms with relays, plus a fail alarm with relay. A digital display of the gas concentration, as well as alarm and status lights, can be viewed through the front window.

The toxic sensors are electrochemical type plug-in sensors, which provide high specificity, fast response, and long life. The plug-in design allows quick replacement in the field with no tools required. Toxic sensors are designed for use in Class I, Div. 2 hazardous locations. Sensors available for NH3, SO2, PH3, AsH3, and HCN.

The M2A represents the latest leading edge technology in sensor / transmitters today.

Features

• Operates with or without a controller
• Direct digital readout with OLED cold temperature display
• Available gases include LEL, O2, H2S, CO, CO2, and 100% Vol CH4 / Toxic gases include NH3, SO2, HCN, and more
• Infrared sensor for combustibles and CO2
• 4-20 mA & digital Modbus outputs standard
• 2 fully programmable alarm relays & fail relay
• Non-intrusive calibration via magnetic wand
• Explosion proof construction
• Patented water repellent sensor cover
• User friendly setup, push buttons & OLED menus
• Long-life sensors (2 + years typical)

*Please note we can only ship RKI products to customers within the United States

65-2640RK M2A Stand Alone Sensor (catalytic) / Transmitter with J-box, LEL 0-100%, (specify calibration), UL Version by RKI Instruments

The RKI M2A™ is a state-of-the-art transmitter that can operate as an independent, stand-alone monitor or as part of an integrated system. The M2A connects with an analog or digital signal to virtually any controller, PLC, or DCS. Setup procedures are simplified with user friendly push buttons and OLED menus. It utilizes a magnetic wand technique for performing non-intrusive calibration. The M2A provides an automatic zero drift correction feature, which results in more stable readings and reduces the need for adjustments due to sensor aging.

The housing of the M2A does not need to be opened for zeroing or calibration, making it unnecessary to declassify the area for routine maintenance. It is designed so that a complete field calibration can be performed by one person. Sensor construction is rated Class I, Div. 1 Groups B, C, D for flammables, CO, H2S, O2, and CO2, and Class I, Div. 2 for all other toxics.

The transmitter provides a 4-20 mA output in addition to a Modbus digital output. It also has two levels of alarms with relays, plus a fail alarm with relay. A digital display of the gas concentration, as well as alarm and status lights, can be viewed through the front window.

The toxic sensors are electrochemical type plug-in sensors, which provide high specificity, fast response, and long life. The plug-in design allows quick replacement in the field with no tools required. Toxic sensors are designed for use in Class I, Div. 2 hazardous locations. Sensors available for NH3, SO2, PH3, AsH3, and HCN.

The M2A represents the latest leading edge technology in sensor / transmitters today.

Features

• Operates with or without a controller
• Direct digital readout with OLED cold temperature display
• Available gases include LEL, O2, H2S, CO, CO2, and 100% Vol CH4 / Toxic gases include NH3, SO2, HCN, and more
• Infrared sensor for combustibles and CO2
• 4-20 mA & digital Modbus outputs standard
• 2 fully programmable alarm relays & fail relay
• Non-intrusive calibration via magnetic wand
• Explosion proof construction
• Patented water repellent sensor cover
• User friendly setup, push buttons & OLED menus
• Long-life sensors (2 + years typical)

*Please note we can only ship RKI products to customers within the United States

603GP2-3V-HE 60" Galvanized Panel Fan, 3-Wing, 2 Hp, 3-Phase, High Efficiency, VFD Compatible by Schaefer

The Schaefer 60" panel fan is designed with large air movement and energy efficiency in mind. These fans feature farm-duty drive belts, heavy-duty, totally enclosed, VFD capable motors and automatic idler tensioner arms. Use in agricultural buildings requiring large volumes and velocities of air movement. Ideal for freestall barns, feed lines, parlors, and holding pens.

IR22-808-D IR 22 Fixed Transmitter with Carbon Dioxide (CO₂) Sensor, 0 - 25% vol. or 0 - 50% vol. Range, Display / 4-20 mA by GfG

The IR 22 transmitter combines the proven infrared measurement method to detect carbon dioxide or combustible gases (HC) with the innovative technique of the new 22 series transmitters. This new GfG transmit- ter generation has been developed and manufactured according to SIL standards.

The comprehensive user menu and the versatile setting options make this transmitter series quite flexible and adaptable to all individual requirements. Precise measurement results at various environmental conditions, as well as the large dynamic measurement range of a few ppm up to 5 % volume CO₂ or 100% LEL.

Time-proven and innovative

The EC 22 is equipped with high quality GfG sensors. The transmitters are fitted with high-performance electronics for voltage stabilization, processing of readings, and temperature compensation. Follow up costs are minimized thanks to the long lifespan of the sensors.

Signal processing

The transmitter includes the complete electronic system for the signal processing and fail-safe forwarding of the measurement signal to the controller. The embedded software of the IR 22 linearises the measurement signal and compensates for environmental influences.

Therefore, when temperature variations are caused by the weather or changes of the humidity, the measured values will be accurate.

In addition, the transmitter provides the option to transfer service, maintenance and error messages to a connected GfG gas measurement controller. The IR 22 transmitter sends the signals either through an analog 4-20 mA current interface or a digital (RS485) Modbus interface.

Flexibility for any application

The IR 22 transmitter includes the sensor, status LEDs, either an analog or a digital interface, "Zero button" to adjust the zero point, and a test socket and potentiometer for the sensor calibration.

In addition, the IR 22 can be ordered with backlit graphical display. The display shows the current gas concentration, allows access to service functions, enables operation using a membrane keypad and includes optical and acoustical signal transmitters.

Features

• Long service life of the infrared (NDIR) sensor
• Extremely stable, low maintenance
• Cost effective single-man adjustment
• Output 4-20 mA or RS485 Modbus

M020-21211-111 QRAE 3 LEL / H2S / CO / O2 Multigas Monitor - Diffusion, Wireless, Accessories Kit by RAE Systems

The QRAE 3 is a full featured compact 4-gas monitor that provides detection and monitoring of Oxygen (O2), Combustibles and toxic gases that include Carbon Monoxide (CO), Hydrogen Sulfide (H2S), Sulfure Dioxide (SO2) and Hydrogen Cyanide (HCN) and others.

QRAE 3 can deliver wireless real-time instrument readings and alarm status 24/7. This provides better incident visibility and can improve response time.

Monitor-only configuration includes

• Monitor as specified
• Sensors as specified
• Sampling option as specified
• Calibration adapter (diffusion model only)
• T Calibration tube (pumped model only)
• Internal filters (mounted - diffusion model only)
• External filters (one mounted plus pack of 3 - pumped model only)
• Travel charger cradle with computer cable
• Lithium-ion battery pack
• Universal wall adapter
• CD ROM with ProRAE Studio II
• CD ROM with product content
• Quick Reference Guide

Key Features

• Available in Diffusion or Pumped version
• IP-65/67 water and dust resistant case
• Strong, protective, concussion-proof design
• Real-time gas concentration readings and alarm status enabled by state-of-the-art wireless technology
• Unmistakable five-way local and remote wireless notification of alarm conditions
• Large graphical display icon-driven user interface through intuitive, simple-to-operate two-button user interface
• Multi-language support: 18 languages encoded
• Easy access to pump, sensors, filter and battery compartment

Applications

• Industrial safety
• Oil and gas
• Fireground "Toxic Twins" detection
• Environmental
• Fire and Emergency response
• Chemical
• Pharmaceutical
• Telecommunications

ODO8000 Stainless Steel Optical DO Probe, 10m, MODBUS output by Sensorex

The Lumin-S optical dissolved oxygen sensor delivers reliable DO measurements over a long operating life. There are no membranes to replace, no electrolyte solutions to replenish, and no anodes to clean. Maintaining the sensor is as easy as replacing the optical sensing cap once every 1-2 years, and since all calibration data is stored on the cap, there's no need to calibrate. This dissolved oxygen sensor outputs a Modbus/RS-485 digital signal for easy PLC integration.

Durable and Reliable

• SS316 body option for fresh water
• Titanium body option for salt water
• Optical technology allows for up to 2 years of use without the need for maintenance

Save Time On Set-up

• No calibration required
• Plug and play

Digital Communication

• Open protocol Modbus RS485 Signal

SPXCDULNFX UL/CSA/INMETRO approved SP XCD Flammable CAT 0-100%LEL (20 to 100%LEL, 10%LEL) with LM25, 3/4 NPT Entry by Honeywell Analytics

Honeywell can trace its company roots back nearly 125 years. What started off as a company dedicated to heating technologies has blossomed into an enterprise dedicated to a variety ofsafety, security, and energy solutions. By integrating the most advanced technologies with intuitive designs, Honeywell has established itself as an industry leader in workplace safety products and gas detection solutions. The company s commitment to advancement and growth help pave the way for innovation and creativity in design. The Sensepoint XCD detection system is the epitome of product advancement. Building on 125 years of industry experience, Honeywell has introduced a comprehensive monitoring system that is reliable, dependable, and state of the art.

Sensepoint XCD

With the Sensepoint XCD detection system, Honeywell provides easy to use, low maintenance sensory devices for monitoring explosive atmospheric conditions in a variety of industrial settings. The Sensepoint XCD system monitors for explosive oxygen gas, toxic gas, and flammable conditions and constantly relays status through transmitters utilizing a simply traffic light LCD system which can be easily seen and understood from a distance.

Superb Versatility

The Sensepoint XCD system provides a catch all-detection system which has worldwide industry approvals and is compliant with all relevant standards. Suited for indoor use as well as the harshest outdoor conditions, the Sensepoint XCD systemis a versatile product for use in any potentially dangerous industrial atmosphere. The unit is available in both stainless steel and aluminum housing options, both of which are resistant to explosions. The XCD transmitter systems are for three separate environmental conditions (flammable, toxic, and oxygen). Each transmitter has a variety of sensors available for use. Each transmitter will automatically recognize the sensor within its category. The plug-in design of the sensors allows users to simply plug the sensor into the transmitter. The transmitter will automatically adjust and configure for the appropriate sensor settings.

Simplicity in Design

The Sensepoint XCD system is easy to install with a simple plug-in design, a built-in mounting system, and comes equipped with versatile wiring receptions to limit compatibility issues for the end user. Once installed, the system utilizes a traffic light type display of green for normal, yellow for warning, and red to alert an atmospheric issue. The maintenance of the system is just as user-friendly with routine maintenance easy and ergonomic enough to be done by one person. The system is also simple enough that it can be used and maintained with little training.

Cost Savings

The Sensepoint XCD system provides a business with cost reductions in both hardware and staffing. The versatile usage and low maintenance of the system reduces the resources needed to monitor conditions and allows personnel to focus on their tasks at hand. The system also provides personnel, and any other parties in the area, peace of mind that their conditions are being constantly monitored for danger and relayed in a way that anyone can detect and bring awareness to dangerous conditions.

M020-11111-111 QRAE 3 LEL / H2S / CO / O2 Multigas Monitor - Pumped, Accessories Kit by RAE Systems

The QRAE 3 is a full featured compact 4-gas monitor that provides detection and monitoring of Oxygen (O2), Combustibles and toxic gases that include Carbon Monoxide (CO), Hydrogen Sulfide (H2S), Sulfure Dioxide (SO2) and Hydrogen Cyanide (HCN) and others.

QRAE 3 can deliver wireless real-time instrument readings and alarm status 24/7. This provides better incident visibility and can improve response time.

Monitor-only configuration includes

• Monitor as specified
• Sensors as specified
• Sampling option as specified
• Calibration adapter (diffusion model only)
• T Calibration tube (pumped model only)
• Internal filters (mounted - diffusion model only)
• External filters (one mounted plus pack of 3 - pumped model only)
• Travel charger cradle with computer cable
• Lithium-ion battery pack
• Universal wall adapter
• CD ROM with ProRAE Studio II
• CD ROM with product content
• Quick Reference Guide

Key Features

• Available in Diffusion or Pumped version
• IP-65/67 water and dust resistant case
• Strong, protective, concussion-proof design
• Real-time gas concentration readings and alarm status enabled by state-of-the-art wireless technology
• Unmistakable five-way local and remote wireless notification of alarm conditions
• Large graphical display icon-driven user interface through intuitive, simple-to-operate two-button user interface
• Multi-language support: 18 languages encoded
• Easy access to pump, sensors, filter and battery compartment

Applications

• Industrial safety
• Oil and gas
• Fireground "Toxic Twins" detection
• Environmental
• Fire and Emergency response
• Chemical
• Pharmaceutical
• Telecommunications

VP5-L1232110211 Ventis Pro5 Personal Gas Monitor, LEL (Methane), CO, H2S, O2, Li-ion Extended Run Time Battery, Desktop Charger, Pump, Black, ATEx/IECEx, LENS Wireless, English by Industrial Scientific

Detect up to five gases simultaneously with the rugged, wireless, Ventis® Pro5 Multi-Gas Monitor. With Ventis Pro5, safety goes beyond the gas detector whether you need team-based alarm sharing, remote monitoring with location details, or both. The monitor is also backed by a Guaranteed for Life™ warranty.

• Eliminate the need for two pieces of equipment by using Ventis Pro5 for personal monitoring and confined space entry.
• Train workers on one, multi-purpose gas monitor and reduce the risk and investment of having different devices in the field.
• Improve team and site safety by locally sharing alarms and gas readings between wirelessly connected Ventis Pro5 monitors.
• Get real-time location and alarm data directly from Ventis Pro5 gas monitors to a designated safety contact with the optional cellular or wi-fi battery pack.
• Reinforce safe behavior with programmable alarm action messages like "EVACUATE" or "VENTILATE" based on alarm level.
• Simplify the user experience with the ability to hide unnecessary screens based on user needs, role, industry, or site.

FFM363S12DD 36" Fiberglass Direct Drive Exhaust Fan, 3-Wing Stainless Steel Blade, 1 / 2 Hp by Schaefer

Schaefer fiberglass exhaust fans are designed and built to be highly efficient (high cfm/watt), long lived and competitively priced fans for agricultural and other applications. The fiberglass exhaust fans are used worldwide to exhaust high volumes of air from factories, warehouses, garages and other locations, where building owners value low capital cost and low operating cost. Fans ship fully assembled with aluminum inlet shutters, self-adjusting belt tensioner and powder coated outlet guard.

Features and Benefits:

• Totally enclosed, thermally protected motors for safety and long life
• Easy belt replacement, minimal maintenance required
• Remote Lubrication System optional
• Aluminum inlet shutter and powder coated outlet guard
• Suitable for buildings with up to 12" wall thickness
• Available in 36", 48" and 52" sizes
• 1-phase and 3-phase motors of various sizes
• 15 year housing warranty
• Two year warranty
• Made in the USA

73-1206-05K RI-600 Stand Alone Carbon Dioxide Monitor, 0-5000 ppm, 115 VAC operation by RKI Instruments

RKI's Model RI-600 measures carbon dioxide in the air. The RI-600 displays the measured carbon dioxide concentration on the LCD. The monitor outputs an analog 4~20mA signal and outputs gas alarm relay contacts open or close when the carbon dioxide concentration rises over preset alarm set point.

The Model RI-600 applies Non-Dispersive Infrared Ray Absorption (NDIR) technique to detect a target gas. The infrared beam emitted from the light source passes through the gas cell and reaches the IR sensor. The target gas enters into the gas cell from the gas inlet. When the target gas is entered into the gas cell, the amount of infrared energy received by the IR sensor decreases since the infrared energy emitted from IR source is absorbed by the target gas. This decreased amount is detected by the IR sensor and is displayed as a gas concentration. There is an optical band pass filter in front of the IR sensor which can pass the absorption wave length of CO₂. Power options are 115 VAC or 24 VDC.

The RI-600 has two preset alarms, and comes ready to operate with a simple wall mount bracket and 10 foot power cord. If a high level of CO₂ is present, the user is notified by an audible alarm tone and the multicolored LCD digital display.

Features

• Operates with or without a controller
• Long life IR sensor
• Large easy to read digital display
• Two power options: 115 VAC, 24 VDC
• Compact wall mount design
• Tri-color visual alarm display: Green for Norman; Yellow for Alarm 1; Red for Alarm 2

Applications

• Brewing Tanks
• Filler Machines
• Storage Tanks
• Bag & Box Rooms
• Indoor Air Quality
• Greenhouse
• Underground Car Park

*Please note we can only ship RKI products to customers within the United States

BW Ultra Portable Multi-Gas Detector with Pump by BW Technologies

At Honeywell, we always put your safety where it should be first. With Honeywell BW™ Ultra, our new portable five-gas detector, you will be able to do the same for your workers. Designed specifically for sampling and monitoring confined spaces, before and after entry, Honeywell BW™ Ultra has enhanced sensor technology, visibility on gas readings, comfort, and connectivity. This makes it the most reliable and user-friendly way to prevent a safety incident.

Extra Gas Detection. Extraordinary.
The Honeywell BW™ Ultra complies with all safety regulations in place by detecting your required gases. Furthermore, it goes the extra mile by offering you the option to choose a fifth sensor from a list of gases for added protection at work.

The Honeywell BW™ Ultra is the first gas detector on the market to feature the 1?Series sensor, with fast response, reliable performance and long life, even in extreme working conditions. That means high accuracy and lower costs.

Features & Benefits

Ultra Easy

• Tamper-proof operation with one button operation
• Intuitive LCD icons for quick decision making
• Easy service and maintenance

Ultra Visibility

• Intuitive large dot matrix display giving clear readings
• Smart Gas layout for clear sensor reading
• Hole Watch Mode for quick decision making
• IntelliFlash™ and also Reverse IntelliFlash™ for clear compliance

Ultra Rugged

• Honeycomb-designed housing for extra ruggedness
• Protection designed in the right place
• Scratch-resistant display protector

Ultra Connected

• Honeywell Connected Worker compatible
• Honeywell TouchConnect™ Technology for activating a feature
• Honeywell SafetySuite for unit configuration and reporting

Ultra Comfortable

• Ergonomically designed for easy use
• Light yet rugged design
• Fits in the hand for easy sampling

Ultra Quick

• Quick responding sensor technology
• Quick decision making because large display
• Quick bump & calibration with IntelliDoX system

XNX-UTSI-NHNNN XNX Universal Transmitter, HART® over 4-20 mA output, UL/CSA/FM approved, 5 x 3/4 in. NPT entries, painted 316 stainless steel, with local HART® interface port, configured for Searchline Excel by Honeywell Analytics

The XNX Universal Transmitter, now with HART EDDL, marks a new turn in gas detection from Honeywell Analytics. It supports the widest range of sensors on a common platform and offers a modular choice of inputs and outputs.

XNX is designed for flexible integration, simple installation, user-friendly operation and straight-forward maintenance. It is ideal for use with a range of gas monitoring controllers or industry standard PLCs. The introduction of our HART Enhanced Device Descriptor Language (EDDL) software provides users with an at-a-glance indication of the health of their gas detectors in the field.

Bringing together the best solutions in gas detection

Electrochemical

• Proven electrochemical sensing technology
• Surecell™ electrochemical cells are ideal for hot and humid environments
• Long life sensing cells (typical >2 years)
• Patented 'Reflex' sensing element verification diagnostics
• Sensor recognition software auto configures transmitter
• Plug and play factory configured sensors
• Intrinsically safe sensor connection permits hot swap, reducing down time

Catalytic Bead

• Supports Honeywell Analytics 705, 705HT, Sensepoint, Sensepoint HT and MPD sensors
• Fast response to wide range of hydrocarbons and flammables

Infrared (Open Path IR, Point IR, IR Cell)

• Supports Honeywell Analytics Searchline Excel, Searchpoint Optima Plus
• Failsafe operation
• Fast speed of response
• Reduced routine maintenance
• Immune to catalytic poisons
• Long operating life
• Works in inert atmospheres

High performance

• Flammable gas detection 0 to 100% LFL/LEL
• Point IR with heated optics provides immunity to poisoning and no hidden faults
• Open-path IR flammable gas detection in LEL-m measurement
• Electrochemical cell offers toxic gas detection in ppm
• IR cell provides CO₂ and combustible gas monitoring
• Robust and reliable operation in explosive areas and harsh environments

Flexible Operation

• 3 versions - supports (Catalytic Bead and IR Cell), Electrochemical Cell and IR (point and open-path) gas detection
• Multi-Purpose Detector (MPD) with field serviceable mV, Catalytic bead and IR Cell capability
• 4-20mA with HART® as standard
• HART Enhanced Device Description Language (EDDL) software*
• Multiple communications options include up to 3 relays, MODBUS® and FOUNDATION® H1 Fieldbus
• Optional local IS port for handheld HART configurator

Easy to Use

• Large, backlit, easy-to-view LCD display offers multisensory indicators (visual icons, colored buttons, text, etc.) to display gas and sensor readings
• User interface supported by 8 selectable languages (English, Spanish, German, Italian, Portuguese, French, Russian, Chinese)
• Self-test and fault indication features
• Non-intrusive, one-man operation
• Quick calibration with auto-inhibit

Easy to Install

• 3 or 4 wire operation, source, sink or isolated
• Simple plug-in sensors and replaceable cells
• NEMA 4X IP66 rated for rugged indoor/outdoor use
• Five conduit entries for ease of installation

Cost Effective

• Minimal training required
• One-man operation
• Plug-in sensor replacement
• All necessary accessories included

WD-89800-14 TC9600 Benchtop Temperature Controller with USB Output, for Thermocouple, RTD, or Thermistors; 230 VAC by Digi-Sense

The benchtop single-loop temperature controllers are designed to regulate a user-defined set point temperature. The microprocessor control provides heating/cooling tolerances for demanding applications found in laboratory or industrial environments. Temperature scale selectable to read in °F, °C, K (Kelvin), or °R (Rankine). An auto-tuning function provides automatic configuration of the PID parameters with minimum user configuration required. Nonvolatile memory stores all user-defined information.

A convenient output receptacle, located on the back of the units, allows for direct plug-in of heaters and other devices. All models accept eight thermocouple types (J, K,N,R,S,T B, and E). Safety features include a loop-break alarm, overtemperature and timer cutoffs, separate fuses for instrument and output receptacle, and audible/visible out-of-range alarms.

The advance controllers also include a USB communication port, audible alarm, external alarm relay output, and a detachable power cord. Free software features real-time graphing, logging of measured temperature and set point temperature, help menu, and ability to interface with other Windows-based programs.

Includes

grid support bracket, electrical noise canceling ferrite clip, and IEC socket power connector for interchangeable cord sets (specify country of destination when ordering).

• Simple on/off control to sophisticated auto-tuning PID control
• Simultaneous view measured value and set point on two-line display
• Front panel indicates output and alarm conditions
• Grid support bracket ideal for fume hood mounting
• Free software offers remote computer control of system operations
• Program up to nine ramp and soak profiles of up to 16 segments each

DOCK2-2-1F-00-G MicroDock II Automatic Test and Calibration Station with GasAlertClip Extreme SO2 Module and 2 Inlets by BW Technologies

BW Technologies by Honeywell has a solid reputation for cost effective, safe, and reliable gas detection and calibration systems. Continuing this trend of excellence, BW Technologies has developed the MicroDock II automated instrument docking station. With multi-language support systems, self-containment, and easy portability, the low cost Microdock II is a great choice for automatic tests and calibrations.

Standard features

The MicroDock II is a hands-free automated calibration and testing system designed to monitor the functions and effectiveness of gas monitoring instruments developed by BW Technologies. The easy to use portable MicroDock II is fully expandable, and can accommodate up to 10 docking modules and 6 charging stations. Once connected, the dock automatically verifies the performance of audible and visual alarms and can calibrate gas detection and measurement. Results of calibration tests and performance measures are automatically recorded. The MicroDock II contains a MultiMediaCard data storage system to provide maximum datalogging and record retention.

Low maintenance

The MicroDock II is a fully functional stand alone automatic test and calibration system. Users do not need to be connected to a computer in order to perform calibration and bump tests. However, the system can be connected via an LAN, and the instrument includes BW Fleet Manager II software for quick and easy data analysis. The instruments long lasting batteries and wall adapter increase the lifespand of the instrument. With limited battery and part replacements, users can rest assured that their investment in the MicroDock II is sure to be sound.

Ease of use

The easy to read instrument display screen and bright LED test indicators ensure maximum readability of test results. The screen provides a real-time clock that displays the time and date of the last calibration and the last bump test, and the LED lights provide unmistakable pass or fail test results . The one button command keys is one of the design features that helps to minimize user training requirements and ensure that the instrument is intuitive and easy to function. Adding additional docking modules to the test station is also simple. Users need only to plug-in connections.

Compatibility

For power, the test system can run on a 6 volt wall adapter or a set of 4 C-cell batteries. The MicroDock II is compatible with a variety of BW Technologies gas monitoring systems including the GasAlertQuatro, GasAlertMax XT II, GasAlertMicroClip, GasAlertMicro 5 Series models, GasAlertClip Extreme (2 and 3 year), and GasAlert Extreme. Users may also purchase an optional wall mount for easy storage. Other optional accessories include the Cal gas wall mount, the MicroDock II portable system kit, demand flow regulator, and network USB. BW Technologies by Honeywell provides a standard 2 year warranty for the MicroDock II.

Worksite managers looking for a high quality, reliable, and low cost automated calibration and test system should look no further than the MicroDock II by BW Technologies. With its simple design, intuitive test result display, and easy to use calibration system, the MicroDock II is the best choice for calibration and testing.

Part Number: DOCK221F00G

10178557 Altair 4XR Multigas Detector, (LEL, O2, H2S & CO), Charcoal Case, North American Charger by MSA

Outfitted with rapid-response MSA XCell® sensors, the ALTAIR 4XR Gas Detector is the toughest 4-gas monitor on the market and is backed by a 4-year warranty. The ALTAIR 4XR can also provide real-time incident awareness to team members, supervisors, safety managers and others when paired with the MSA ALTAIR Connect app via a Bluetooth® wireless connection.

Real-time

• Sense gas 2 times faster than the industry average with our XCell sensors
• Quickly update MSA ALTAIR 4XR settings via the ALTAIR Connect app (available on the Google Play Store)
• Send event notifications via text message with the ALTAIR Connect app

Rugged

• Survives 25 drops from 4 feet (1.2 meters) (MIL-STD-810G drop protection)
• Can survive an incidental 25-foot (7.5-m) drop onto concrete
• Dust- and waterproof IP68 rating (2 meters for at least 1 hour)
• Operating temperature range: -40°F to +140°F (-40°C to +60°C)

Reliable

• 4-year instrument & sensor warranty
• Confirm compliance quickly with the Bump LED & on-screen checkmark
• Bump and calibrate with 1/2 the test gas and in 1/2 the time vs. industry average
• Bump and calibrate at a specified "Time of Day" with your MSA GALAXY® GX2 Automated Test System
• MotionAlert option tells others that user has become immobile
• User-activated InstantAlert notifies others of a potentially dangerous situation

IR22-701-M IR 22 Fixed Transmitter with Methane (CH₄) Sensor, 0 - 100% LEL Range, No Display / Modbus by GfG

The IR 22 transmitter combines the proven infrared measurement method to detect carbon dioxide or combustible gases (HC) with the innovative technique of the new 22 series transmitters. This new GfG transmit- ter generation has been developed and manufactured according to SIL standards.

The comprehensive user menu and the versatile setting options make this transmitter series quite flexible and adaptable to all individual requirements. Precise measurement results at various environmental conditions, as well as the large dynamic measurement range of a few ppm up to 5 % volume CO₂ or 100% LEL.

Time-proven and innovative

The EC 22 is equipped with high quality GfG sensors. The transmitters are fitted with high-performance electronics for voltage stabilization, processing of readings, and temperature compensation. Follow up costs are minimized thanks to the long lifespan of the sensors.

Signal processing

The transmitter includes the complete electronic system for the signal processing and fail-safe forwarding of the measurement signal to the controller. The embedded software of the IR 22 linearises the measurement signal and compensates for environmental influences.

Therefore, when temperature variations are caused by the weather or changes of the humidity, the measured values will be accurate.

In addition, the transmitter provides the option to transfer service, maintenance and error messages to a connected GfG gas measurement controller. The IR 22 transmitter sends the signals either through an analog 4-20 mA current interface or a digital (RS485) Modbus interface.

Flexibility for any application

The IR 22 transmitter includes the sensor, status LEDs, either an analog or a digital interface, "Zero button" to adjust the zero point, and a test socket and potentiometer for the sensor calibration.

In addition, the IR 22 can be ordered with backlit graphical display. The display shows the current gas concentration, allows access to service functions, enables operation using a membrane keypad and includes optical and acoustical signal transmitters.

Features

• Long service life of the infrared (NDIR) sensor
• Extremely stable, low maintenance
• Cost effective single-man adjustment
• Output 4-20 mA or RS485 Modbus

01-14870 Peabody Gemini Round Dual Containment Tank, Blue, 120 Gallon 1.5 Specific Gravity by Quantrol

Features and Benefits of Gemini Tank System

• Specifically designed for the Water Treatment Industry
• Linear polyethylene construction. Polypropylene, XLPE and PVDF available - Superior chemical resistance for acids, caustics, sodium hypochlorite, biocides, etc. Handles aggressive applications that stainless steel and crosslink polyethylene will not.
• Heavy duty dual wall construction - Rated for liquids of 1.5 or 2.0 specific gravity. "Tank in a Tank" designed for instances where the primary tank fails; the chemical will then be safely contained in secondary tank.
• Integral pump mounting platform - Lid has 240 pound rating allowing for use with metering pump or mixer mounted directly to tank lid. Sump reservoir collects and drains pump spilled liquid back to primary.
• Pump pick-up tube port - Install pump suction line with check valve quickly and easily. Once installed, tank contents are sealed from outside environment.
• Integral mouse door - Molded directly into most Gemini models, recessed mouse door allows for inexpensive installation of optional bottom bulkhead fitting for flooded suction connection or bottom fill.
• Custom colors and mold-in graphics - Custom colors available, subject to minimum order quantity. Private label mold-in graphic is molded directly into tank and wont weather, crack, peel, or deteriorate.