All Products

10154076 Altair 2X Single Gas Detector, H2S-LC (5, 10), Charcoal by MSA

Introducing the ALTAIR 2X Gas Detector from MSA; the first one or two gas detector that incorporates industry-leading XCell Sensor Technology to deliver unparalleled performance while drastically minimizing total cost of ownership, increasing durability and delivering enhanced worker safety, compliance and traceability.

The Altair 2X is also the first portable gas detector to introduce revolutionary XCell Pulse Technology. Based on proven science and advanced patented sensor capabilities, the Altair 2XP detector delivers the world's first stand-alone bump test. This allows a daily bump test to be performed without the need for calibration accessories or specific calibration gas.

ALTAIR 2XP Gas Detector with xCell Pulse Technology

ALTAIR 2xT Two-Tox Gas Detector

ALTAIR 2X Single Gas Detector

Features & Benefits

Low cost of ownership

• Fastest sensor response times, lowest calibration gas flow rate on the market
• 4-year expected instrument & sensor life
• 3-year warranty on instrument & most sensors (2 years on Cl2, NH3)
• Stand-alone bump tests reduce maintenance, increase productivity (ALTAIR 2XP only)
• 1 device can monitor 2 gases (ALTAIR 2XT only)

Increased safety awareness & real-time compliance

• Stand-alone bump test anytime, anywhere without specific calibration gas (ALTAIR 2XP only)
• Bump pass: green LED flash every 15s, large on-screen checkmark
• Bump fail or expiration: red LED flash every 15s, no checkmark
• End-of-sensor-life warning and alarm

Full-time traceability

• Records 75 alarm events
• 150+ hours of periodic data (ALTAIR 2X and 2XP)
• 100+ hours of periodic data (ALTAIR 2XT)
• Compatible with MSA GALAXY® GX2 Automated Test System and MSA Link Pro software

Rugged durability

• Tough over-molded rubber armor
• Survives multiple 25-ft drops onto concrete
• Agency-certified dust- and water-tight IP67 construction
• Intrinsically-safe design

6500-2101 MGS-350 Gas Detector, R134a 0-1,000 ppm IP66 Housing by Bacharach

Bacharach's MGS-350 Series Gas Transmitter is a feature-rich gas detection system with a wide range of sensor options to provide real-time monitoring of refrigerant, combustible, TVOC and toxic gases. It comes standard with analog and digital outputs including 4-20 mA, 0-5V, 0-10V and Serial Data, allowing them to connect directly to most BMS, SCADA or control systems. An onboard visual LED alarm indicator alerts area personnel when levels have exceeded the desired limit. The MGS-350 also features alarm relays (high and low) for connection to external audible/visual alarms or a BMS or BAS system.

MGS-350 Gas Transmitters, combined with the MGS Controller, can provide facility owners with a customized and complete low-cost gas-detection system. A variety of housing options are available (shown below), from standard to water resistant enclosures, which allow the MGS-350 units to be placed in many environments.

Features & Benefits:

• Detects refrigerants (CFCs, HFCs, HCFCs), TVOCs, combustible gases/hydrocarbons, O2, NH3, CO, H2S, H2, NO, NO2, SO2, Cl2, and O3
• Long-lasting infrared, semiconductor, catalytic bead and electrochemical sensor options for effective leak detection - at the most affordable cost.
• Precalibrated replacement sensors for easy maintenance
• Integrated visual LED alarm
• Two onboard alarm relays (low and high)
• Multiple housing options available, including IP 66 and duct mount, for placement in diverse environments.
• Analog outputs: 4-20 mA, 0-5V, 0-10V, featuring 12/24 VAC / 12-30VDC operation

10154073 Altair 2XT Two-Tox Gas Detector, CO/NO2 (CO: 25, 100; NO2: 2.5, 5), Charcoal by MSA

Introducing the ALTAIR 2X Gas Detector from MSA; the first one or two gas detector that incorporates industry-leading XCell Sensor Technology to deliver unparalleled performance while drastically minimizing total cost of ownership, increasing durability and delivering enhanced worker safety, compliance and traceability.

The Altair 2X is also the first portable gas detector to introduce revolutionary XCell Pulse Technology. Based on proven science and advanced patented sensor capabilities, the Altair 2XP detector delivers the world's first stand-alone bump test. This allows a daily bump test to be performed without the need for calibration accessories or specific calibration gas.

ALTAIR 2XP Gas Detector with xCell Pulse Technology

ALTAIR 2xT Two-Tox Gas Detector

ALTAIR 2X Single Gas Detector

Features & Benefits

Low cost of ownership

• Fastest sensor response times, lowest calibration gas flow rate on the market
• 4-year expected instrument & sensor life
• 3-year warranty on instrument & most sensors (2 years on Cl2, NH3)
• Stand-alone bump tests reduce maintenance, increase productivity (ALTAIR 2XP only)
• 1 device can monitor 2 gases (ALTAIR 2XT only)

Increased safety awareness & real-time compliance

• Stand-alone bump test anytime, anywhere without specific calibration gas (ALTAIR 2XP only)
• Bump pass: green LED flash every 15s, large on-screen checkmark
• Bump fail or expiration: red LED flash every 15s, no checkmark
• End-of-sensor-life warning and alarm

Full-time traceability

• Records 75 alarm events
• 150+ hours of periodic data (ALTAIR 2X and 2XP)
• 100+ hours of periodic data (ALTAIR 2XT)
• Compatible with MSA GALAXY® GX2 Automated Test System and MSA Link Pro software

Rugged durability

• Tough over-molded rubber armor
• Survives multiple 25-ft drops onto concrete
• Agency-certified dust- and water-tight IP67 construction
• Intrinsically-safe design

Xgard Gas Detectors

Crowcon is a global leader in designing and manufacturing gas detection technology and equipment. The company has been in operation for over 40 years and is consistently building upon its products. By integrating modern technology with the demands of the modern workplace, Crowcon has developed a line of gas detection devices and monitors that lead the competition. The Xgard range of gas detectors is a product of Crowcon s successful integration and technological advancements. With a wide range of sensor types and available accessories, the Xgard series is suitable for all worksites and is customizable enough to fit any needs.

Tough and reliable

The Xgard series of fixed point gas detectors is incredibly durable and reliable. The casings and materials, including weatherproof caps, are designed to protect the equipment from the harshest environments. The detectors are made from a variety of materials depending on the model: glass reinforced nylon, aluminum with polyester coating, and 316 stainless steel.

Variety of sensors

The fixed point gas detector offers a wide range of sensors for to suite almost all applications. The Xgard range of gas detectors is available in three models to meet varying worksite needs: flameproof, intrinsically safe, and safe area formats. Additionally, Xgard offers different types of fixed point gas detectors within these three models:

• Xgard Type 1- Intrinsically safe toxic and oxygen gas detectors
• Xgard Type 2- Flameproof toxic and oxygen gas detectors
• Xgard Type 3- Flameproof flammable gas detector
• Xgard Type 4- Flameproof high temperature flammable gas detector
• Xgard Type 5- Flameproof flammable gas detector with 4-20mA output
• Xgard Type 6- Flameproof thermal conductivity type gas detector
• Xsafe- Safe area flammable gas detector

Cost efficient and highly effective

With quick and easy installation and maintenance, the Xgard series is able to keep costs at a minimum. The replacement sensors, for example, are simple to replace by merely plugging them in. The replacement parts are also readily available and compatible with all Xgard models, thereby reducing the amount of required spare parts that are stored in the facility. Additionally, the sensors have two times the typical life spans of similar sensors in the industry. With a 2 year life span, worksites can expect to cut their sensor replacement costs in half. For worksites that require slightly more customization, Crowcon offers compatible accessories for the Xgard series such as sampling applications, remote gassing applications, spray deflectors, sun shields, weatherproof caps, collector cones, flow adapter, and accessories adapter.

Xgard also has flexible installation options. The unit is designed for either wall or ceiling mounts, and users will not need to purchase additional equipment for mounting. For more complex installation needs, users can purchase accessories.

Specifications

Each model is approximately the same size with dimensions of 6.1 x 6.5 x 4.3 inches and weighing approximately 1 or 2 pounds. The battery type, electrical output, and power requirements vary based on the sensor type. For a complete listing of gas sensors, types, and individual specifications, please see the product specifications listing.

750A Refrigerant Leak Detector by Test Products International

The 750a features 400 hour sensor life under normal use; a spare sensor is included with each instrument for a total of 800 hours of continuous use and can detect leaks as small as 0.2 ounces per year (R134a / R22).

Whether testing for leaks in air conditioning, refrigeration, or automotive AC, the versatile 700 series spans the diverse needs of technicians, refrigeration engineers, and maintenance personnel around the globe. From freezer coils to heat pumps, experience fast, reliable results that save you both time and money.

The TPI 750a is a state-of-the-art refrigerant leak detector capable of detecting all halogen based gases. Selectable sensitivity combined with an adjustable tick rate will allow any service professional to pinpoint those tough to find leaks even in contaminated environments.

Sensor life can be extended by fitting a 1/2" long piece of vinyl tubing onto the sensor tip. This tubing helps prevent foreign material from getting into the sensor during tests; clean or replace the tube regularly.

Even though TPI refrigerant leak detector sensors are very durable and can last up to 400 hours, sensor life can be aided by press fitting a 1/2" long piece of vinyl tubing onto the sensor tip. This tubing helps prevent foreign material from getting into the sensor during tests. Clean or replace the tube regularly.

Features

• Detects all existing refrigerants and blends including 404A, PURON 410A and *R-507 (AZ50)
• 400 hour individual sensor life; a spare sensor is included with each instrument for a total of 800 hours of continuous sensor use.
• Fast response; Begin testing immediately after power on
• 0.2 ounce per year sensitivity
• One hand thumb wheel operation
• Pinpoint small leaks easily by elimination of background concentration with fully adjustable tic rate
• Visual indicators for power, tic rate and battery replacement
• Optional earphone attachment

Applications

• Check for leaks in refrigeration systems
• Test for leaks in air conditioning systems and cooling units
• Find leaks in automotive air conditioning systems

Standard Accessories

• Sensor: A712
• Instruction Manual: 750a Instruction Manual
• Soft Pouch A700

Optional Accessories

• Soft Case w/strap A755
• Earphone A710
• Test vial A713

10178560 Altair 4XR Multigas Detector, (LEL, O2, H2S & CO), Charcoal Case, Global Charger by MSA

Outfitted with rapid-response MSA XCell® sensors, the ALTAIR 4XR Gas Detector is the toughest 4-gas monitor on the market and is backed by a 4-year warranty. The ALTAIR 4XR can also provide real-time incident awareness to team members, supervisors, safety managers and others when paired with the MSA ALTAIR Connect app via a Bluetooth® wireless connection.

Real-time

• Sense gas 2 times faster than the industry average with our XCell sensors
• Quickly update MSA ALTAIR 4XR settings via the ALTAIR Connect app (available on the Google Play Store)
• Send event notifications via text message with the ALTAIR Connect app

Rugged

• Survives 25 drops from 4 feet (1.2 meters) (MIL-STD-810G drop protection)
• Can survive an incidental 25-foot (7.5-m) drop onto concrete
• Dust- and waterproof IP68 rating (2 meters for at least 1 hour)
• Operating temperature range: -40°F to +140°F (-40°C to +60°C)

Reliable

• 4-year instrument & sensor warranty
• Confirm compliance quickly with the Bump LED & on-screen checkmark
• Bump and calibrate with 1/2 the test gas and in 1/2 the time vs. industry average
• Bump and calibrate at a specified "Time of Day" with your MSA GALAXY® GX2 Automated Test System
• MotionAlert option tells others that user has become immobile
• User-activated InstantAlert notifies others of a potentially dangerous situation

1418-024 Micro IV Single Gas Detector with 3-Year Sensor Warranty, Hydrogen Sulfide (H2S), Standard 0 - 100 ppm by GfG

Durable, compact design

Widest Range of sensors

Easy Operation

Up to six months of battery life

Clip-on attachment

Optional motorized pump

Large graphic display

Audible, vibrating and visual alarms

Lifetime warranty

DS220 docking station

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Standard Accessories

• Micro IV detector
• Specified Sensor
• Alkaline Battery
• Rubber Boot
• Manual

1450-922 G400 Motorized Smart Pump Rechargeable by GfG

Optimized Alarm System

The new G400 MP-2 pump continuously communicates with the G450/G460 gas detector. This interaction allows fault indication via the detector display. Alarms such as low battery, blocked sampling line or interrupted power fault are shown on the display and activate a visual and audible alarm on the monitor.

Various Applications

Gas samples can be taken from a distance of up 100 meters (over 300 feet) at a typical draw rate of 0.5 liters per minute.

Superior Flexibility

The G400 MP-2 is the only detachable pump on the market today which will allow for operation in both diffusion mode and remote sample-draw mode. Simply slide the shutter to turn the pump on or off. When the pump is on, the shutter covers the diffusion inlets and exposes them when the pump is switched off.

The G400 MP-2 features a high efficiency redundant filter system in addition to a standard external probe with dust and hydrophobic filters.

Independent Power Supply

The G400 MP-2 is operated by its own power supply, independent of the gas detector. The power supply of the pump allows for up to 10 hours of continuous operation.

Features

• Optimized alarm system: Visual alarm via the G450/G460 display and alarm LEDs, Audible alarm via the G450/G460, Vibration alarm via the G450/G460
• Allows monitor to be used in either pump or diffusion mode
• Independent power supply (does not reduce instrument battery capacity)
• 300 feet (100 meter) remote sampling capability

Includes

• 10' of Tubing
• Probe with Filters

MCXL-X0H0-B-OE GasAlertMicroClip XL Detector, Oxygen (O2), Hydrogen Sulfide (H2S) - Black Housing, OE Version (Other Regions, 2-pin UK plug) by BW Technologies

The easy to wear, slim and compact GasAlertMicroClip provides affordable protection from atmospheric gas hazards. For standard operation with features you can count on, opt for the GasAlertMicroClip XT. For extended battery life, especially in cold weather, choose the GasAlertMicroClip XL. Both offer visual compliance at a glance with the flashing, green IntelliFlash™. Easy onebutton operation reduces training time and lets workers focus on the job at hand. For simple, cost-effective management of your records, calibration and bump testing, choose BW's MicroDock II automatic test and calibration system and Fleet Manager II software.

• Easy and comfortable to wear; thin and lightweight
• Easy operation and straightforward training with one-button simplicity
• Easy visual compliance with flashing, green IntelliFlash™
• Easy and cost effective to own

Additional GasAlertMicroClip features:

• Choose the GasAlertMicroClip XL for cold weather performance
• IntelliFlash™ verifies operation and compliance to both the user and supervisor
• Tamper-proof, one button operation
• Powered by a rechargeable lithium polymer battery

Standard features of BW multi-gas products:

• Continuous LCD shows real-time gas concentrations
• Compact and lightweight design makes it comfortable to wear
• Water-resistant
• Simple automatic calibration procedure; compatible with BW MicroDock II automatic test and calibration station
• Full function self-test of sensor, battery status, circuit integrity and audible/visual alarms on start up
• Bright wide-angled visual alarm bars
• Built-in concussion-proof boot
• Multi-language support in English, French, German, Spanish and Portuguese
• Conveniently manage your fleet using Fleet Manager II

Part Number: MCXLX0H0BOE

Observer Software by SE International

The New Observer USB is a free version of the Observer software that runs on Windows®. It can be used with The Ranger, The Ranger EXP, & The Monitor 200 Radiation Detectors. The Observer USB reads in Counts, CPM, and CPS, as well as μR/hr, mR/hr, and μSv/hr and has the ability to collect, log, and perform statistical analysis on the data received. No Mac or WinRT versions available. However, for info about running windows on an Apple computer, please click here.

Free Download of the Observer USB Software:

Observer USB Software 1.3.0.8

Downloaded Data Sample

Previous Revision:
Observer USB 1.1.1.0

G450-11040 G450 Multi-Gas Detector with Flashlight Rechargeable Battery, O2, LEL by GfG

GfG is one of the industry s leading producers of workplace safety products. Their products are safe, reliable, and customizable. Their state of the art research and development facility produces the most advanced products on the market. Additionally, their dedicated team of safety professionals works to ensure that each product can be equipped with customization tools and modifications to ensure that each product can be optimized to meet the most rigorous workplace safety standards. Introducing the G450 Multi-gas Detector, GfG is continuing its legacy as a safety leader.

G450 Multi-gas Detector

The G450 Multi-gas Detector continually measures up to four separate atmospheric gases. In confined spaces, the detector will monitor LEL combustible gas, oxygen, H2S, and CO. The easy to use G450 series of detectors is designed with user friendliness in mind. Many of its most common functions are operated with a single button, and the unit features a fully automatic calibration system. Users need only to attach the adaptor and flow gas to the sensors. The unit s GfG AutoCal system will automatically initiate the calibration sequence and will update the necessary information on the G450 Multi-gas Detector.

Long Battery Life

The G450 Multi-gas Detector also features a long life battery operation that is most efficient for workplace safety. The device has a batter life of up to 25 hours of continuous operation. With alkaline packs, the units are powered by 2 AA batteries, and when placed in the drop in cradle, the rechargeable battery packs can be fully recharged in less than 4 hours. The rechargeable packs have optional flash light LEDs to indicate charge level.

Triple Alarm System

This unit features an elaborate alarm system that is not to be missed. The triple alarm system features a loud audible alarm of 103dB, a vibrating alarm, and bright 360 wrap around LEDs with a colored backlit display for visual alarms. The alarm system ensures that users and those nearby are fully aware of possible environmental hazards. Additionally, the easy to read backlit display will light varying colors from green, orange, and red to intuitively notify users of the severity of the conditions.

Features

The G450 Multi-gas Detector is encased in a dust proof and highly water resistant housing. The housing even contains a built in rubber boot to help protect from regular wear and tear. Each unit is equipped with datalogging capabilities. The datalogger records and internally stores all activity and environmental conditions. Users can download this information to their computers and use it to research, analyze, and evaluate the jobsite environment.

The multi-gas detection system comes standard with a few accessories including a calibration adaptor, a training manual, and a training DVD. The rechargeable devices include the previous accessories and additional drop in cradle chargers and a wall power adaptor. Optional accessories include a datalogging kit, self powered attachable motorized sample pump, spare battery packs, and rechargeable battery packs. The breadth of available accessories helps to ensure that the G450 Multi-gas Detector can be customized to meet the needs of individual work spaces.

MicroMax Pro Serviceable Multigas Portable

The MicroMAX Pro is the best microprocessor controlled multi-gas monitor on the market today. It s the only monitor that has it all easy to use, reliable, highest quality, economical, lightweight, shortest response time, built-in data logging, lifetime warranty* and now includes our newest innovation...

Since worker safety is our business, Lumidor continually strives to improve its gas detector product line, and has done so with the addition of the voice message feature. Four languages (English, French, German and Spanish) are included with each monitor - just select the desired language. Every function, when activated, is accompanied with a voice message. Everything from immediate warnings to simple on and off functions are communicated verbally to the user. This feature is also very valuable in poorly lit situations. And, the language displayed on the new 4-line display is the same as the one selected for the voice.

The MicroMAX Pro is designed to provide the ultimate in personal safety. It s OSHA compliant, and has a rugged case that provides superior RFI/EMI shielding, as well as dust, water and impact resistance. Additionally, it is designed, tested and manufactured under strict ISO 9001 standards, and is UL classified for use in Class I, II, III Division I, Groups A, B, C, D, E, F, G.

The MicroMAX Pro combines diffusion and built-in internal sampling pump systems for simultaneously monitoring 1 - 5 gases. The popular internal pump allows for easy pre-testing in confined spaces and provides almost instantaneous readings of gas concentrations. In order to save power, the pump can be switched off and the diffusion mode will take over.

The MicroMAX Pro has preset and field selectable alarms. Both audible and visual alarms warn the user if the oxygen levels are either too low or enriched, combustible gas is present or toxic gas levels are too high. The toxic gas alarms can be easily adjusted in the field from immediate to TWA. And, alarms are also activated in case of sensor failure, low battery voltage, pump blockage or low air flow.

Our unique microprocessor design allows for self diagnostics with each start up. The MicroMAX Pro internally data logs individual channel alarms, TWA averaging and peak information. With a push of the Mode button you can review information, as well as customize user settings or initiate calibration.

All stored information is available for display, and meets OSHA documentation for employee awareness programs by simply downloading to a standard Windows™-compatible PC with Lumidor s MPRO-DATALOG software.

Calibration is easier than ever before-it s all automatic-no tools, screws or stopwatch required. Simply place in calibration Mode , introduce calibration gas and wait for voice/display indicating calibration is complete!-A NiMH rechargeable battery pack and 4-hour charger are now included with each monitor.

Included Accessories

• Rubber boot with shoulder strap
• Rechargeable NiMH battery pack with 4-hour charger
• Dust filter
• Alkaline battery holder 10 sampling hose with water trap and particulate filter
• MPRO-DATALOG Windows™ 95/98 compatible data logging software and interface cable

Optional Accessories

• External vibrator alarm
• External earphone alarm
• Leather carrying case
• DC-to-DC vehicle charging adapter
• Aluminum or fiberglass search probes
• High-impact carrying case
• Calibration gases Bump test gases
• Confined space kits

Version 5.0 upgrade

• Up to 24 calibration records stored in unit for later download
• Calibration history reports generated
• Compatibility with most Windows™ platforms
• Easier, more functional, user interface with enhanced menus, toolbar, screen displays and calibration dialog

44512R Gasurveyor 512R 4 Button Portable Gas Detector - PPM, LEL, VOL - Rechargeable by GMI

The GMI Gasurveyor 500 series is the most flexible range of gas detectors available today. By simple selection of hardware and software options the instrument can be readily configured to suit your exact application.

Features

• Measures flammable, oxygen and toxic gases
• Dual mode operation - Combustible Gas Indicator (CGI) / ConfinedSpace Monitor (CSM)
• Rechargeable or alkaline battery options
• Approved to European and North American safety standards
• Extremely robust anti-static case
• Simple to use
• Built-in sampling pump as standard
• Large LCD with automatic backlighting in low level light conditions
• Compatible with the GMI range of Auto Calibration Systems
• Audible / visual alarms for all gas ranges
• Fault alarms for low flow, low battery etc.
• Probes for a wide range of applications

Includes

• G500 carrying case
• Harness
• Hex driver
• 1.5Mt clear sample line
• User manual
• Probe handle
• 35 cm probe (solid end)
• Sample line adaptor
• Dry cell batteries (not USA) or NiCad pack and cotton filters (20).

Part Number: DXPSNA

Part Number: DXSTAND

CL-O-19.5 Clip SGD Maintenance Free Single Gas Disposable Monitor, O2 19.5/23.5% by Crowcon

Clip Single Gas Detector (SGD) is designed for use in hazardous areas and offers reliable and durable fixed life span monitoring in a compact, lightweight and maintenance-free package. Clip SGD has a 2-year life and is available for hydrogen sulphide (H₂S), carbon monoxide (CO) or oxygen (O₂).

Clip SGD is designed to withstand the harshest industrial working conditions and delivers industry leading alarm time, changeable alarm levels and event logging as well as user-friendly bump test and calibration solutions.

Easy to maintain

• Changeable alarm levels - ensures compliance with changing regulations or company procedure
• Clip SGD docking station - keeps monitors correctly configured without service or technician team
• 'Bump test due' indication - alerts the user and team members that the monitor is not compliant and requires a bump test

User-friendly

• Compact and lightweight - non-intrusive and comfortable to wear, perfect for any length of shift
• Single button operation - delivers simplicity for users and reduces training time

Efficient

• Wide operating temperature range - effective in a wide variety of harsh environments
• Water and dust resistant to IP66 and IP67