Monitor

MC110 pH Monitor by Milwaukee

The MC Monitors are designed to continuously monitor pH, EC or TDS values directly in your reservoir. Each unit features a user selectable set-point. An LED visual alarm is activated and flashes when the pH, EC or TDS level rises either Above or Below (user selected) that set-point.

All these instruments run on a 12V adapter so there's no need to worry about failed batteries and each unit comes with mounting kit, probe, probe holder and starter calibration solution.

Professional pH monitor especially designed for use with aquariums.

• User selectable Hi/Low Set Point
• Manual 2 points calibration
• Visual LED alarm
• Supplied with 12 VDC adapter, mounting kit, and 20ml pH 7.01 calibration solution
• Double junction pH electrode with 2m cable (BNC connector)

MC120 pH Monitor by Milwaukee

The MC Monitors are designed to continuously monitor pH, EC or TDS values directly in your reservoir. Each unit features a user selectable set-point. An LED visual alarm is activated and flashes when the pH, EC or TDS level rises either Above or Below (user selected) that set-point.

All these instruments run on a 12V adapter so there's no need to worry about failed batteries and each unit comes with mounting kit, probe, probe holder and starter calibration solution.

Professional pH monitor especially designed for use with aquariums.

• User selectable Hi/Low Set Point
• Manual 2 points calibration
• Visual LED alarm
• Supplied with 12 VDC adapter, mounting kit, and 20ml pH 7.01 calibration solution
• Double junction pH electrode with 2m cable (BNC connector)

Single Gas

Available for the following gases:

• Versions available for combustible gas, oxygen and toxic gases
  
• Rechargeable versions for all gas types
  
• Non rechargeable versions for oxygen and toxic gases
  
• Ultra lightweight – just 80g for toxic versions
  
• Loud 95dBA audible alarm
  
• Dual colour visual alarm, red blue twin flashing LEDs
  
• Vibrating alarm
  
• IP65 and IP67 ingress protection
  
• Real time TWA and Peak display options
  
• Optional datalogging

Multigas monitor with capability to monitor exotic toxic gases

Special Features

• Low Flow alarm shuts pump off to avoid damage to instrument.
• Hydrophobic filter disc in probe.
• Internal dust filter (or optional internal hydrophobic filter).
• Quick autocalibration using 4 in 1 calibration gas standard.
• Single gas calibration capability.
• Methane elimination switch for environmental applications.
• "Adjustment Lockout Switch" for added security.
• Confirmation beep (silenceable).
• Backlight, automatic for alarms and by demand with adjustable time.
• Meets EPA Method 21 protocol for fugitive emissions testing.
• Land surveyor (land survey equipment).

MONGUA Guardian Monitor by Bluelab

See your desired levels of pH, conductivity and temperature - 24/7.

Monitoring your crops 24 hours a day, with the ability to set high and low alarms for each parameter. A flashing display lets you know if your parameters move away from the optimum, allowing you to make the important adjustments quickly and effectively. The large, clear display allows readings to be viewed from a distance.

The Bluelab® Guardian Monitor is mains powered and is either mounted to the wall or hung on a support and probes positioned inside your reservoir / solution.

Probe cable length: 2 meters / 6.5 feet

Features

• Wall mount for continuous viewing
• Plant-safe green LEDs, with adjustable brightness
• Large easy to read displays
• Replaceable double junction pH probe included
• Easy to navigate menu to program & adjust settings
• Selectable conductivity and temperature scales
• No calibration required for conductivity and temperature
• Simple push button pH calibration
• Flashing high and low alarms (non-audible)
• Built with greater tolerance to RF / electronic interference
• International power supply
• Non-volatile memory

Are your workers constantly trashing their gas monitors by leaving them out in the rain, dunking them in water, or dropping them on the ground resulting in costly repairs?

Features

• One button operation. Works just like a computer mouse. Either single click or double click. No complicated functions to learn allows workers to start using the Tetra almost instantly.
  
• 12 hours of operation. No more instruments going dead at the end of a work shift
  
• 30 day calibration timer. Never again forget to calibrate and risk a large OSHA fine
  
• Field changeable intelligent sensor modules allows you to replace sensors without having to send the unit in for repair
  
• Rechargeable Lithium Ion or AA Alkaline versions available
  
• Rubberized casing to absorb shock, and keep dust and water out
  
• Loud and bright - 90 dba audible alarms and Red/Blue high intensity LED visual alarms will get noticed by your workers
  
• Internal Vibrating alarm at no charge
  
• TWA (time weighted average) and STEL (Short Term Exposure Limit) alarms. Now you can monitor for these two important levels set by OSHA. This is usually a costly extra feature on other monitors
  
• Datalogging capability - can be downloaded to a computer via infrared connection for doing reports and data analysis
  

770 Carbon Monoxide Monitor by Test Products International

The 770 CO Single Gas Monitor is a state-of- the-art Carbon Monoxide Instrument designed to measure Carbon Monoxide in ambient air and to perform a carbon monoxide build up test . It has a measurement range of 0 to 999 ppm (parts per million) and displays the readings in 1ppm increments.

The unit features a personal audible and visual alarm, which is factory set at 30ppm CO but can be changed in the field to keep current with government legislation.

Other features include: maximum reading hold, elapsed time and manual zero. The audible alarm may be switched on and off as required. Battery changing is made easy by use of a simple slide off battery compartment cover.

The detector uses an advanced electrochemical sensor that measures Carbon Monoxide and should not be used for any other purpose.

When the audible alarm is switched off a small 'double speaker' symbol will be displayed at the bottom left of the LCD. When the alarm setting is exceeded a 'warning' symbol is displayed at the bottom center of the screen and the red warning indicator is illuminated. As the battery level approaches 2 volts a 'BAT' warning symbol is displayed to indicate low battery level. When the battery level gets too low the unit will automatically switch off.

Features

• Measure CO from O to 999ppm
• Displays the max. CO reading in PPM since power on
• Displays in hours and minutes, time elapsed since power on
• Displays user set value of audible and visual alarm
• The audible alarm can be switched on and off by pressing the SEL button

Applications

• Ambient CO safety checks

Are your workers tired of lugging around large, bulky, heavy gas detection equipment? Are you tired of dealing with repeated equipment failures and units that are always in the shop?

• Available in CO, H2S, O2, LEL configurations
• CO, H2S, O2 models run for 3000 hours on alkaline batteries
• LEL model runs for 16 hours
• 2 year warranty
• Small and Lightweight
• High Quality and Low Cost
• Peak, STEL, and TWA alarms
Now both of these problems are a thing of the past. The 01 series are single gas monitors that are exceptionally easy to operate, with unmatched reliability. Simply install the batteries and the units are ready to operate. No complicated set up, and no hassles. Workers will be protected with three levels of alarms. Audible, Visual, and Vibration will make sure users are alerted to a dangerous condition no matter what the environment is. For example if a worker is in a particularly noisy environment they may not hear the audible alarm but they will feel the vibration and see the bright LED visual alarms. The alarms are user adjustable and can be set to any level to meet your particular situation, but come defaulted to OSHA recommended set point levels.

Radiation Alert Area Monitor by SE International

The Radiation Alert® Area Monitor is one of the most user friendly, all inclusive, state of the art radiation area monitors available. The easy to use interface is an intelligent resistive touch screen display featuring a large five digit LED readout.

It comes with either an internal or external detector and free software for monitoring every Radiation Alert® Area Monitor on your network. Includes user selectable warning indicators for low and high radiation alarm levels, low battery, and detector failure. Setup email and text alerts to recieve alarms while on the go. All the settings are stored internally, even when power is disconnected. All units come with a Certificate of Conformance. NIST Source calibrations available upon request.

Monitor 200 Compact Radiation Detector by SE International

The Monitor 200 measures alpha, beta, gamma, and x-rays. Its digital display shows readings in your choice of CPM, CPS, μSv/hr, mR/hr, or in accumulated counts. It has a digital display, a red count light, and a beeper that sounds with each count detected. Other features include an adjustable timer, and selectable alert. With the free Observer USB Software Family, you can set computer alarms, calibrate your instrument, and download your collected data from the internal memory for easy reporting!

MC810 MAX pH/TDS/Temp Monitor by Milwaukee

ACCURATE. SIMPLE. RELIABLE. 24/7 PH/TDS/TEMP MONITORING.

Why Guard when you can Monitor! The Milwaukee MC810 MAX pH/TDS/Temp Monitor lets you monitor your pH/TDS/Temp levels 24/7 automatically.

COMMENTS FROM FIELD TESTING

"I run this unit 24/7 and have not had any problems for the past two months. I can monitor 24/7, point a camera on it and connect to my phone."
"Easy to calibrate."
"Using this now, far less expensive than what my friends paid ... I recommend this to any serious grower."

SUMMARY

The MC810 MAX Monitor automatically monitors and displays pH/TDS/Temp levels. Just calibrate the parameters and let the Milwaukee MAX Monitor do the rest.

The Milwaukee MC810 MAX pH/TDS/Temp Monitor is preferred by people looking to know 24/7 what their pH and nutrient levels are on an ongoing basis. Common uses are nutrient tanks, Hydroponics and aquariums.

The Milwaukee MAX pH/TDS/Temp Monitor offers:

ACCURACY

The Milwaukee MAX Monitor offers an accuracy to ± 0.2 pH with two point manual calibration, TDS accuracy of ±2% Full Scale and ±0.5 °F (0.3C) temperature accuracy.

AUTOMATION

Just calibrate the parameters and begin to monitor 24/7!

EASY INSTALLATION

The MC810 MAX pH/TDS/Temp Monitor comes with a complete mounting kit including a probe holder.

DESIGN FEATURES

• Fast easy to read current results with 3 large digital BACKLIT LCD readouts.
• Accurate to ±0.2 pH (0.0 pH to 12.0 pH).
• Accurate ±2% Full Scale TDS.
• External Switch atop the unit converts EC conductivity to TDS (ppm) using 0.5 or 0.7 conversion factor.
• Simple two-point pH calibration and one point TDS, for increased accuracy with manual trimmers for easy adjustment.
• Gel-filled, double junction MA911B/2 (included) lab grade pH electrode for low maintenance and high performance.
• 6.5 feet probe cables for extra flexibility when testing.
• 12 VDC power supply.

USE AND CARE

pH meters usually start performing poorly because of problems with the probe. The two parts of the pH probe that cause problems are the glass sensing bulb and the reference junction.

SENSING BULB

The glass bulb loses sensitivity with use and will eventually fail. This is true of all pH probes.

REFERENCE JUNCTION

The reference junction is a small hole that allows the meter to compare the sample to a reference. The reading is generated based on the electrical difference between the sample and reference. If the junction hole gets clogged, the pH probe will no longer function.

You can extend the life of your pH electrode in the following ways.

STORAGE

The pH probe needs to be kept hydrated. Long periods of dry storage will damage the sensitivity of the probe. Allowing the probe to dry out may also result in the junction hole getting clogged.

Storing in pH probe storage solution or pH calibration buffers will help address both these issues. Do not store in tap water and DI water. This will damage the sensitivity of the probe.

The best way to store the probe is with the probe's cap filled with storage solution or calibiration buffer and the cap tightened to prevent leakage. It is also recommended that to store the electrode upright to further reduce the potential for leakage.

CLEANING

Residue from the sample can impact the sensitivity of the sensing bulb and clog the junction. This is especially true if the sample has a lot of organic material. We recommend regularly soaking your electrode in cleaning solution.

CALIBRATION

The pH sensing bulbs become less sensitive over time so make sure that you are calibrating reguarly to keep your PRO pH controller accurate. Also, calibrate after cleaning or a long period of storage.

MC811 MAX pH/EC/Temp Monitor by Milwaukee

ACCURATE. SIMPLE. RELIABLE. 24/7 PH/TDS/TEMP MONITORING.

Why Guard when you can Monitor! The Milwaukee MC811 MAX pH/EC/Temp Monitor lets you monitor your pH/EC/Temp levels 24/7 automatically.

COMMENTS FROM FIELD TESTING

"I run this unit 24/7 and have not had any problems for the past two months. I can monitor 24/7, point a camera on it and connect to my phone."
"Easy to calibrate."
"Using this now, far less expensive than what my friends paid ... I recommend this to any serious grower."

SUMMARY

The MC811 MAX Monitor automatically monitors and displays pH/EC/Temp levels. Just calibrate the parameters and let the Milwaukee MAX Monitor do the rest.

The Milwaukee MC811 MAX pH/EC/Temp Monitor is preferred by people looking to know 24/7 what their pH and nutrient levels are on an ongoing basis. Common uses are nutrient tanks, Hydroponics and aquariums.

The Milwaukee MAX pH/EC/Temp Monitor offers:

ACCURACY

The Milwaukee MAX Monitor offers an accuracy to ± 0.2 pH with two point manual calibration, EC accuracy of ±2% Full Scale and ±0.5 °F (0.3 °C) temperature accuracy.

AUTOMATION

Just calibrate the parameters and begin to monitor 24/7!

EASY INSTALLATION

The MC811 MAX pH/EC/Temp Monitor comes with a complete mounting kit including a probe holder.

DESIGN FEATURES

• Fast easy to read current results with 3 large digital BACKLIT LCD readouts.
• Accurate to ±0.2 pH (0.0 pH to 12.0 pH).
• Accurate ±2% Full Scale EC.
• External Switch atop the unit converts EC conductivity to EC using 0.5 or 0.7 conversion factor.
• Simple two-point pH calibration and one point EC, for increased accuracy with manual trimmers for easy adjustment.
• Gel-filled, double junction MA911B/2 (included) lab grade pH electrode for low maintenance and high performance.
• 6.5 feet probe cables for extra flexibility when testing.
• 12 VDC power supply.

USE AND CARE

pH meters usually start performing poorly because of problems with the probe. The two parts of the pH probe that cause problems are the glass sensing bulb and the reference junction.

SENSING BULB

The glass bulb loses sensitivity with use and will eventually fail. This is true of all pH probes.

REFERENCE JUNCTION

The reference junction is a small hole that allows the meter to compare the sample to a reference. The reading is generated based on the electrical difference between the sample and reference. If the junction hole gets clogged, the pH probe will no longer function.

You can extend the life of your pH electrode in the following ways.

STORAGE

The pH probe needs to be kept hydrated. Long periods of dry storage will damage the sensitivity of the probe. Allowing the probe to dry out may also result in the junction hole getting clogged.

Storing in pH probe storage solution or pH calibration buffers will help address both these issues. Do not store in tap water and DI water. This will damage the sensitivity of the probe.

The best way to store the probe is with the probe's cap filled with storage solution or calibiration buffer and the cap tightened to prevent leakage. It is also recommended that to store the electrode upright to further reduce the potential for leakage.

CLEANING

Residue from the sample can impact the sensitivity of the sensing bulb and clog the junction. This is especially true if the sample has a lot of organic material. We recommend regularly soaking your electrode in cleaning solution.

CALIBRATION

The pH sensing bulbs become less sensitive over time so make sure that you are calibrating reguarly to keep your PRO pH controller accurate. Also, calibrate after cleaning or a long period of storage.

MC310 EC - Conductivity Monitor by Milwaukee

The MC Monitors are designed to continuously monitor pH, EC or TDS values directly in your reservoir. Each unit features a user selectable set-point. An LED visual alarm is activated and flashes when the pH, EC or TDS level rises either Above or Below (user selected) that set-point.

All these instruments run on a 12V adapter so there's no need to worry about failed batteries and each unit comes with mounting kit, probe, probe holder and starter calibration solution.

• User selectable Hi/Low Set Point
• Manual 1 points calibration
• Visual LED alarm
• Supplied with 12 VDC adapter, mounting kit, and 20ml 1413 µS/cm calibration solution
• MA811/2 EC Conductivity Probe with 2m cable (BNC connector)

MC410 TDS - PPM Monitor by Milwaukee

The MC Monitors are designed to continuously monitor pH, EC or TDS values directly in your reservoir. Each unit features a user selectable set-point. An LED visual alarm is activated and flashes when the pH, EC or TDS level rises either Above or Below (user selected) that set-point.

All these instruments run on a 12V adapter so there's no need to worry about failed batteries and each unit comes with mounting kit, probe, probe holder and starter calibration solution.

• User selectable Hi/Low Set Point
• Manual 1 points calibration
• Visual LED alarm
• Supplied with 12 VDC adapter, mounting kit, and 20ml 1382ppm calibration solution
• MA81/2 PPM Probe with 2m cable (BNC connector)

AQ VOC Handheld TVOCs Monitor by E Instruments

The SI-AQ VOC Monitor is the ideal instrument for you should your specific application require testing for Volatile Organic Compounds (VOCs) or potentially harmful gasses such as Carbon Monoxide (CO). In addition, the (Si-VOC) Si-AQ VOC Monitor can an also be outfitted with up to three (3) Gases sensors in total among VOC, CO₂, CO, Formaldehyde, NO₂, NO, O₂, SO₂ & H₂S in addition to measuring Relative Humidity, Ambient Temperature and Barometric Pressure.

Accurate / Reliable / Robust / Fast

• Dynamic PID TVOC Sensor: 0 - 20,000 ppb or 0 - 200 ppm
• Temp., %RH, & Barometric Pressure Included
• Real-Time Data Logging
• Active Internal Sampling Pump
• Large Internal Memory (2,000 Tests)
• Protective Magnetic Rubber Boot
• Optional Wireless Printer
• Optional Handheld Probe

• Select Up To 3 Gases in Total: TVOCs, CO₂, CO, Formaldehyde, NO₂, NO, O₂, SO₂, H₂S
• Long Lasting Rechargeable Battery & AC Charger
• Light Weight & Durable
• Si-AQ PC Software & USB Cable

AQ VOC Kit includes:

• Temperature, %RH, Wet Bulb, Dew Point
• Barometric Pressure
• PC Software & USB Cable
• Real-Time Continuous Data Logging
• Bluetooth® Connectivity
• Protective Carrying Case
• Continuous Active Internal Sampling Pump
• Long Lasting Battery & AC Charger
• Factory Calibration Certificate
• Quick Start Guide

6702-8030 MGS-401 Entrance Monitor by Bacharach

The MSA Bacharach® MGS-401 Entrance Monitor centralizes the status of up to four (4) MSA Bacharach diff usion Gas Detectors, which in turn provides and audible and visual alarm outside a monitored space. In addition, the MGS-401 displays any gas concentration level in the space for additional information and visual monitoring. System configuration will determine whether the alarms signals are addressed in the monitored space or at a controller or BMS/BAS level. Combining the MGS-401 Entrance Monitor with the MGS-408 Gas Controller and diffusion Gas Detectors provides a complete, single source gas detection system with an easy means of achieving compliance with refrigeration safety standards such as IIAR, ASHRAE 15, CSA B52 and EN376.

FEATURES

• Perimeter strobe for "at-a-glance" system / alarm status
• Seamless integration with all MSA Bacharach diffusion Gas Detectors
• MGS-408 Controller powers up to (8) total of combination of MGS-401(s) and MGS Diffusion Gas Detectors
• Modbus RTU Master / Slave provides seamless integration from connected gas detectors to many third-party BMS / BAS
• Audible and visual alarms enable compliance with IIAR, ASHRAE 15, CSA B52 and EN378 - no additional hardware required

MONGUACON Guardian Monitor Connect by Bluelab

A constant indicator of pH, conductivity and temperature, enabling you to optimise these parameters.

Monitor and wirelessly data log the essential nutrient solution parameters - pH, conductivity and temperature - when teamed up with a Bluelab® Connect™ Stick and local computer. Keeping track of the growth history on your computer will give you the blueprint for crop success again and again.

Guard your results by setting a high and low alarm range in each parameter and receive digital notification if the solutions move outside the alarm ranges set.

Probe cable length: 2 meters / 6.5 feet

Features

• Wall mount for continuous viewing
• Remote viewing with Bluelab® Connect™ Software and Apps
• Replaceable double junction pH probe included
• Bright, plant-safe green LED with adjustable brightness
• Easy to navigate menu to program & adjust settings
• Selectable conductivity and temperature scales
• No calibration required for conductivity and temperature (factory calibrated)
• Simple push button pH calibration
• Flashing high and low alarms (non-audible)
• Built with greater tolerance to RF / electronic interference
• International power supply