All Products

2811-722-004 EC 28 Gas Transmitter with Sensor, Nitrogen Dioxide (NO2), Display / Alarm / Relay by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

M5IR-XUBH-R-P-D-Y-N-00 GasAlertMicro 5 IR Detector CO2 (IR), % LEL (Unfiltered), O2, H2S - Rechargeable Battery and Pump - Yellow Housing by BW Technologies

The GasAlertMicro 5 Series is the most customizable gas monitoring series on the market. With an extensive selection of models, user options, and instrument settings, this multi-gas detector series is an industry leader. BW Technologies by Honeywell recognizes that not all worksites can operate with a one size fits all model of gas detection devices. With the introduction of the GasAlertMicro 5 Series multi-gas detectors, worksites, managers, and users can utilize the customizable features to ensure that the instrument meets their specific worksite needs.

GasAlertMicro 5 Series models

This multi-gas monitor series is available in several models: the standard toxic gas model, a PID model for detection of VOCs, or an IR model for CO2 detection. The unit accurately and reliably identifies up to five atmospheric hazards simultaneously and can rapidly switch from diffusion mode to the optional integrated pump.

Each model of GasAlertMicro 5 Series has several distinct features. With the GasAlertMicro 5 Series, the standard toxic gas model, users can monitor several standard gases with a plug in electrochemical cell sensor and catalytic cell sensor and a typical battery life of 20 hours (AA Alkaline rechargeable). The GasAlertMicro 5 PID is standard with several gas detections, a plug in electrochemical cell sensor and photoionization detector, and a battery life of approximately 15 hours (AA Alkaline rechargeable). Finally, the GasAlertMicro 5 IR features specific gas detection ranges, a plug in electrochemical cell sensor, a catalytic cell sensor, and an infrared sensor for carbon dioxide monitoring. This model also has a battery life of approximately 15 and AA Alkaline rechargeable batteries. For more information about available sensor configurations, please contact BW Technologies by Honeywell.

Exclusive features

Each GasAlertMicro 5 Series device features several exclusive features including a triple alarm system, raised glove-friendly buttons, a large easy to read display, stainless steel alligator clip, visual filter inspection, and automatic activation tests. When the unit is activated, the gas detector will automatically test for sensor integrity, circuitry, and battery. This continuous and reliable testing process ensures that the integrity and dependability of the device is never a concern.

BW Technologies by Honeywell also recognizes the unique needs of the various industries with environmental hazards. With each industry anticipating a separate set of possible dangers, the ability to customize safety devices is critical.

Users and worksite managers will be comforted to know their GasAlertMicro 5 series model is fully customizable. Customizable features include STEL intervals, TWA methods, sensor activation, alarms, display settings, record keeping, pumps, combustible gas measurements, start up calibration, backlights, activation modes, calibration levels, daily bump tests, and languages. To protect the integrity of the user settings and the safety of the gas monitoring device, the GasAlertMicro 5 device features a passcode function to prevent unauthorized manipulation of settings.

Accessories

The GasAlertMicro 5 Series is also compatible with BW's MicroDock II automatic test and calibration system. Users may purchase additional accessories to help fully tailor the gas detection unit to their needs. Accessories include an integral pump and battery charger, a confined space kit, a belt holster, and a collapsible sampling probe.

Part Number: M5IR-XUBH-R-P-D-Y-N-00

*Please note we can only ship RKI products to customers within the United States

CP-I-W50000S3-Y-00 BW Icon+ Multi-Gas Detector, %LEL(IR) SO2 Yellow by BW Technologies

Serviceable four-gas detector with a choice of six sensors — Honeywell BW™ Icon+ delivers an icon-based experience in a serviceable package. It enables you to maximize the lifespan of your four-gas detectors, optimize long-term cost of ownership and select from multiple gas sensors for flexible applications.

ICON DISPLAY FOR FAST DECISIONS

Like the fixed-life Honeywell BW™ Icon, Honeywell BW™ Icon+ is named for its firstin-the-industry display of simple icons for gas levels and device status. That means no live gas readings for workers to interpret and no time-consuming training. Instead, when there's a gas alarm, the bell icon on the display will illuminate, along with an indicator next to the sensor in alarm, so workers can quickly clear the area.

INTELLIGENT SENSORS FOR PREDICTIVE MAINTENANCE

How much life is remaining in the H₂S sensor, based on its age and gas exposure? When does the O₂ sensor need to be calibrated? Honeywell BW™ Icon+ has i-Series intelligent sensors that answer these kinds of questions, so you can take action and prevent unexpected downtime.

REPORTING AND ANALYSIS FROM YOUR SMARTPHONE

Want to see the full concentration of a gas or other information not on the icon-based display? Need to report a gas alarm? Simply download the Honeywell Safety Suite Device Configurator app, use Bluetooth® to pair your smartphone with the detector, and open the app to see the data — all organized in a report that's ready to send.

FEATURES AND BENEFITS

• RELIABLE: Two months of battery runtime on a 4.5-hour charge — and up to four months if you turn off the detector at the end of each shift. No daily charging, no unexpected downtime.
• COMPATIBLE: The Honeywell BW™ Icon+ is compatible with the IntelliDoX instrument management system and Honeywell Safety Suite and also with TouchConnect™ using Bluetooth® for wireless configuration.
• ACCURATE: Low-power infrared LEL sensor is immune to silicone poisoning, which means accurate monitoring of combustibles.
• EASY TO MANAGE: The IntelliFlash™ green light indicates when the detector is in compliance and the amber light indicates the need for maintenance.
• RESPONSIVE: 1series sensors respond to dangerous gas levels in seconds, even in harsh temperatures.
• EASY TO USE: Small, lightweight and wearable. One-button operation.

Part Number: CP-I-W50000S3-Y-00

*Please note we can only ship RKI products to customers within the United States

Part Number: M1016300PN

0560 0460 460 Pocket Pro Compact Tachometer by Testo

testo 460 optically measures rpm, e.g. of ventilators and shafts. The measurement spot is displayed on the measurement object with an LED marking. Max./min. values are displayed directly at the press of a button. The backlit display allows the measurement values to be easily read out, even in unfavourable light conditions. testo 460 is very handy, small and easy to operate.

• Optical rpm measurement with LED measurement spot marking
• Max./min. values
• Incl. calibration protocol
• Protective cap for safe storage
• Including wrist strap and belt holder
• Display light
• Reflective markers

CS22-D CS22 Fixed Transmitter, Display / 4-20 mA by GfG

Wherever toxic or flammable gases and vapors must be monitored without requirements for explosion protection, the use of the CS22 is recommended.

Proven and cost-effective

The CS22 works on the principle of chemisorption (CS). Thanks to a wide range of monitorable gases and multiple measurement ranges, the CS22 offers a wide range of uses, from laboratories to industrial applications to refrigeration systems.

Transmitters with electrochemical sensors (EC), are also used with toxic and flammable gases. In contrast, the CS22 is a much more durable and cost-efficient solution. However, the environmental parameters must fit.

Communicates analog and digital

The measured values and status information of the CS22 can be transmitted either analog (4-20 mA or 0.2-1 mA) or digital (RS-485). This allows not only the use in combination with any GfG controller, but also the connection to programmable logic controllers (PLC).

Smart measured value processing

Industry-wide, the trend is towards smart units, such as the CS22, whose integrated electronics process the data already at the measuring point. The linearization of the measurement signal, compensation of temperature influences, detection of malfunctions and information on the next service or maintenance interval are just some of the advantages that result.

Variants for every requirement

The basic version of the CS22 is sufficient for many applications. If a measured value display on site is desired, there is also a variant with display and acoustic alarm.

CS22 Basic variant for a wide range of catalytic sensors
CS22 D with display to show the current measured value

In combination with GfG's powerful controllers, both variants are the right choice for a wide range of gases to be monitored.

Part Number: XTSC1B

Part Number: 44L-407

Old Part Number: Z106730A
New Part Number: Z106730PA

CP-I-00X10000-B-00 BW Icon+ Multi-Gas Detector, O2 Black by BW Technologies

Serviceable four-gas detector with a choice of six sensors — Honeywell BW™ Icon+ delivers an icon-based experience in a serviceable package. It enables you to maximize the lifespan of your four-gas detectors, optimize long-term cost of ownership and select from multiple gas sensors for flexible applications.

ICON DISPLAY FOR FAST DECISIONS

Like the fixed-life Honeywell BW™ Icon, Honeywell BW™ Icon+ is named for its firstin-the-industry display of simple icons for gas levels and device status. That means no live gas readings for workers to interpret and no time-consuming training. Instead, when there's a gas alarm, the bell icon on the display will illuminate, along with an indicator next to the sensor in alarm, so workers can quickly clear the area.

INTELLIGENT SENSORS FOR PREDICTIVE MAINTENANCE

How much life is remaining in the H₂S sensor, based on its age and gas exposure? When does the O₂ sensor need to be calibrated? Honeywell BW™ Icon+ has i-Series intelligent sensors that answer these kinds of questions, so you can take action and prevent unexpected downtime.

REPORTING AND ANALYSIS FROM YOUR SMARTPHONE

Want to see the full concentration of a gas or other information not on the icon-based display? Need to report a gas alarm? Simply download the Honeywell Safety Suite Device Configurator app, use Bluetooth® to pair your smartphone with the detector, and open the app to see the data — all organized in a report that's ready to send.

FEATURES AND BENEFITS

• RELIABLE: Two months of battery runtime on a 4.5-hour charge — and up to four months if you turn off the detector at the end of each shift. No daily charging, no unexpected downtime.
• COMPATIBLE: The Honeywell BW™ Icon+ is compatible with the IntelliDoX instrument management system and Honeywell Safety Suite and also with TouchConnect™ using Bluetooth® for wireless configuration.
• ACCURATE: Low-power infrared LEL sensor is immune to silicone poisoning, which means accurate monitoring of combustibles.
• EASY TO MANAGE: The IntelliFlash™ green light indicates when the detector is in compliance and the amber light indicates the need for maintenance.
• RESPONSIVE: 1series sensors respond to dangerous gas levels in seconds, even in harsh temperatures.
• EASY TO USE: Small, lightweight and wearable. One-button operation.

Part Number: CP-I-00X10000-B-00

2104-2000 EC 21 Fixed Gas Transmitter with Internal Sensor, Carbon Monoxide (CO), 1 ppm, 0 - 2000 ppm by GfG

GfG s EC 21 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Simple gas detection

The EC 21 is the simplest way to monitor ambient conditions. Simply attach the EC21 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in the air.

The EC 21 is reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector hasa "quick disconnect" feature to simplify transmitter installation and service.

Mounting Position of the EC 21

To determine the mounting position of the EC 21 it is important to know and consider the ambient conditions. To achieve the best results, the ventilation conditions and the density of the gases need to be considered.

The EC 21 must be installed so that the gas reaches the sensor even in poorly ventilated areas. If necessary, check the area with a smoke cartridge.

Other influences such as water (rain, dripping or condensation) and dust need to be considered as well.

Features

• Simple to use and extremely economical
• Robust housing is corrosion resistant and dust-tight>
• Linear 4 to 20 mA output signal
• 18 - 24 VDC

6300-2031 MGS-150 Gas Transmitter, NH3: 0 - 500 ppm, IP66 Housing, Low Temp by Bacharach

MGS-150 Series Gas Transmitter is a feature-rich gas detection system with a wide range of sensor options to provide real-time monitoring of refrigerant, combustible, and toxic gases. It comes standard with user-selectable analog and digital outputs that can be set for 4-20 mA, 0-5V, 1-5V, 0-10V, or 2-10V; allowing them to connect directly to most BMS, SCADA or control systems. Alarm indicators include an onboard alarm LED and audible buzzer, in addition to an alarm relay for connection to external audible/visual alarms or a BMS system. The product's alarm threshold value is pre-set to factory defaults but is also field programmable. A variety of housing options are available (shown below), from standard IP41 enclosures to IP66 water resistant housings, which allow the MGS-150 Series gas sensors to be placed in the toughest of conditions.

Ideal for Commercial and Industrial Refrigeration, Food Storage and Food Processing Facilities, Supermarkets, Parking Garages, Wastewater Treatment Facilities, Hospitals and Universities.

Features & Benefits:

• Infrared, semiconductor and electrochemical sensor options to meet almost any gas detection need - at the most affordable cost.
• User-selectable analog outputs: 4-20 mA, 0-5V, 0-10V, 1-5V, 2-10V featuring 12/24 VAC/VDC operation.
• Fast-response sensors detect leaks quickly, which protect personnel and minimize refrigerant gas usage and environmental impact.
• Long-life semiconductor sensors for detection of all refrigerants, ammonia, halocarbons, combustible gases & VOCs.
• Robust design and remote sensor options allow units to be placed directly in areas where detection is needed.
• Available in a variety of housings, including IP66 and duct mount, for placement in the toughest of environments.

619F pH/Temperature with Graphical Display and Replaceable pH Electrode by Jenco

VisionPlus pH619 fits the gap between the top of the line pH618N and the lower end pH630. With IP67 body, temperature readout, menu driven operation and replaceable electrode module. VisionPlus pH619 is a powerful and easy to use pH tester. Available in two different models: one for °Celsius temperature readout and one for Fahrenheit temperature readout.

VisionPlus pH619 is RoHS compliant.

• Graphical LCD provides on-screen menu selection for manual-free, easy operation.
• On-screen messaging displays useful information such as meter status, buffer selection and operation modes. no more guess work involving cryptic indictors or flashing digits.
• 4-button keypad provides intuitive operation with separate buttons for data hold, calibration, data memory storage and memory retrieval.
• IP67 rated, water-proof dust-proof body.
• Glass bulb electrode exposes more measuring surface to solution for fast response time.
• Surface mounted temperature element improves temperature accuracy and response time.
• Clear LCD displays pH and temperature at the same time, along with meter status, calibrated buffers, status, date and time.
• Large temperature range for wide range of applications.
• 1,2, or 3 point calibration, with automatic buffer recognition of us and nist buffer sets.
• Calibration data is stored in memory, ready for use on power up, even when batteries are removed.
• Readings are automatically compensated for temperature (ATC).
• Data hold for convenient reading.
• Watertight case is ideal for rugged use. protective cover for pH electrode is included.
• Replaceable electrode module ensures extended usefulness.
• Belt clip which also attaches to neck strap.
• 1 year warranty.

2087-1 UV Flame Detector (20/20U) by Crowcon

Crowcon supplies a wide range of detectors designed to detect flames extremely quickly and over long distances. The detectors can operate in difficult envonmental conditions and incorporate sophisticated algorithms and logic to prevent false alarms.

Features:

• Explosion proof ATEX, FM, CSA and GOST-R standards
• IR, UV, UV/IR and IR3 options
• Aluminium or stainless steel construction
• 4-20mA, RS-485 or standard 4-wire relay operation

Old Part Number: XD106710PA
New Part Number: X106710PA