4 Gas Calibration Gas

72-5620RK-XX Eagle Portable Monitor for LEL & PPM/O2/CO/H2S/HCl/CO2 (With External H2S Scrubber) by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

This is the equivalent of the CG-Q58-4JK from BW

Part Number: 58L-402ES

5934-0309 GDC-350 Gas Sensor Monitor, NEMA 4 Housing, O2/SO2 with Display by Bacharach

Bacharach's all new GDC-350 full-featured fixed gas monitors provide superior operation - standalone or as part of a larger system utilizing the standard analog outputs. This state-of-the-art instrument can detect a wide range of gases including carbon monoxide (CO), oxygen (O2), combustible gases, refrigerants and total volatile organic compounds (TVOCs). The GDC-350 provides a unique two sensor interface, allowing for multiple gases to be detected with onboard or remote sensors. Sensors can be located integral to the unit or remotely allowing for sensors to be placed directly in areas where potential leaks can occur. Bacharach s proprietary calibration algorithms extend the amount of time required between calibrations, reducing maintenance costs and lowering the overall cost of ownership for non-critical applications.

The GDC-350 has all the features and functionality for any application. LED alarm indicators visually indicate when alarm conditions are met and an audible alarm alerts nearby personnel. An onboard alpha numeric display shows gas readings in real time for each sensor. Integral dry contact relays are available to drive external audible / visual alarms, activate fans, or connect to building management and control systems. Installation and maintenance is simple and easy, reducing overall system cost. A pre-wired plug-in option is available for out-of-the-box operation. Simply plug the unit into any standard AC outlet for immediate detection and protection.

65-2405RKSS S2 Series LEL Transmitter/Detector/XP Stainless Steel J-Box, 4 - 20 mA, Specify Calibration by RKI Instruments

Having a reliable gas sensor is detrimental to the safety and security of workers in potentially unstable work environments. In many cases, the decision to use a gas detection device with a reliable sensor can be the difference between life and death. RKI Instruments understands the reliability of gas sensors should be a top priority for workplace safety managers. Their team of experts works diligently to incorporate the most advanced technologies with the highest industry standards.

For nearly 20 years, RKI Instruments has worked in the gas detection industry. Its line of products leads the industry in innovation and technology. Every year, the company commits to achieving a higher level of productivity and delivering the best gas detection products on the market. With the introduction of their high performing, low cost S2 Sensor Transmitter, RKI is fulfilling that commitment.

S2 Sensor/Transmitter

The RKI S2 Sensors and Transmitters use state of the art sensor technology to detect common gas hazards. Their efficient design and cost effectiveness make them an industry choice for atmospheric monitoring. The sensor transmitters can be used in both indoor and outdoor conditions and are designed to interface with RKI controllers or PLC/DCS systems.

The sensors are available in explosion proof casing for monitoring LEL, H2 specific, oxygen, H2S, CO2, and carbon monoxide. These sensors also have flame arrestors and are approved for use in hazardous environments. The oxygen, H2S, CO, and CO2 sensors are available in non-explosion proof models. The sensors provide highly specific and quick detection and are long lasting. The sensors can be quickly replaced while on the field and do not require any tools.

Explosion proof S2 Sensor/Transmitter

The explosion proof sensors use a variety of detection mechanisms including catalytic for LEL and LEL- H2 specific; metal oxide semiconductor for hydrogen; galvanic cell technology for oxygen; electrochemical for hydrogen sulfide and carbon monoxide; and infrared for carbon dioxide, methane, and hydrocarbons. A hydrogen specific sensor transmitter is not available. Each of these detection methods come with their own measuring range specifications and response times varying from 20 seconds to 45 seconds. These sensors are stainless steel and are housed in a cast aluminum explosion proof J-Box (a stainless steel J-Box is also available).

Non-explosion proof S2 Sensor/Transmitter

The non-explosion proof sensors use galvanic cells for oxygen detection; electrochemical technology for hydrogen sulfide, carbon monoxide, and other toxics; and infrared technology for carbon dioxide detection. The response times vary between 20 seconds and 60 seconds depending on the targeted gas, and the measuring ranges vary as well. These sensors are plastic or aluminum and housed in an explosion proof J-Box.

Accessories

The S2 Sensor/Transmitter has numerous accessories available to meet the individual workplace's needs. Such accessories include calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors or panels, and data loggers.

Each sensor comes standard with a one year warranty for materials and workmanship.

*Please note we can only ship RKI products to customers within the United States

65-2405RKSS-05 S2 Series LEL Xmitter/Detector/XP SS J-Box, 4 - 20 mA, CSA Version, Specify Calibration by RKI Instruments

Having a reliable gas sensor is detrimental to the safety and security of workers in potentially unstable work environments. In many cases, the decision to use a gas detection device with a reliable sensor can be the difference between life and death. RKI Instruments understands the reliability of gas sensors should be a top priority for workplace safety managers. Their team of experts works diligently to incorporate the most advanced technologies with the highest industry standards.

For nearly 20 years, RKI Instruments has worked in the gas detection industry. Its line of products leads the industry in innovation and technology. Every year, the company commits to achieving a higher level of productivity and delivering the best gas detection products on the market. With the introduction of their high performing, low cost S2 Sensor Transmitter, RKI is fulfilling that commitment.

S2 Sensor/Transmitter

The RKI S2 Sensors and Transmitters use state of the art sensor technology to detect common gas hazards. Their efficient design and cost effectiveness make them an industry choice for atmospheric monitoring. The sensor transmitters can be used in both indoor and outdoor conditions and are designed to interface with RKI controllers or PLC/DCS systems.

The sensors are available in explosion proof casing for monitoring LEL, H2 specific, oxygen, H2S, CO2, and carbon monoxide. These sensors also have flame arrestors and are approved for use in hazardous environments. The oxygen, H2S, CO, and CO2 sensors are available in non-explosion proof models. The sensors provide highly specific and quick detection and are long lasting. The sensors can be quickly replaced while on the field and do not require any tools.

Explosion proof S2 Sensor/Transmitter

The explosion proof sensors use a variety of detection mechanisms including catalytic for LEL and LEL- H2 specific; metal oxide semiconductor for hydrogen; galvanic cell technology for oxygen; electrochemical for hydrogen sulfide and carbon monoxide; and infrared for carbon dioxide, methane, and hydrocarbons. A hydrogen specific sensor transmitter is not available. Each of these detection methods come with their own measuring range specifications and response times varying from 20 seconds to 45 seconds. These sensors are stainless steel and are housed in a cast aluminum explosion proof J-Box (a stainless steel J-Box is also available).

Non-explosion proof S2 Sensor/Transmitter

The non-explosion proof sensors use galvanic cells for oxygen detection; electrochemical technology for hydrogen sulfide, carbon monoxide, and other toxics; and infrared technology for carbon dioxide detection. The response times vary between 20 seconds and 60 seconds depending on the targeted gas, and the measuring ranges vary as well. These sensors are plastic or aluminum and housed in an explosion proof J-Box.

Accessories

The S2 Sensor/Transmitter has numerous accessories available to meet the individual workplace's needs. Such accessories include calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors or panels, and data loggers.

Each sensor comes standard with a one year warranty for materials and workmanship.

*Please note we can only ship RKI products to customers within the United States

81-SM2003U Single Point Calibration Station for GX-2003, Model SM-2003U by RKI Instruments

The SM-2000 single module calibration station for the GX-2009 and GX-2003 portable gas monitors is a stand alone station that can calibrate, bump test, charge, and archive data without the need of a computer to operate. The module has 4 operating modes, which include bump test only, % volume methane bump/calibration (for the GX-2003), calibration only, and bump with automatic calibration (if the bump test fails). The SM-2000 modules are capable of storing up to 200 bump test or calibration records. To download the data each module includes a 1 GB USB flash drive. Also included is a software package to import the data from the USB drive and manage records by serial #, user ID, or station ID. Each module has user adjustable test times and tolerances to meet specific testing requirements. The charger within the module quick charges battery packs within 90 minutes and will recognize alkaline batteries. The Calibration Station power requirements are 115/230 VAC, 50/60Hz.

Features:

• Stand alone system, no PC needed for operation
• Calibrate, bump test, charge, and archive data
• Software manages records by serial #, user ID, or station ID
• Each station is equipped with configuration control and status indicators
• User adjustable test times and tolerances
• Automatic quick charge of instrument in 90 minutes or less
• Exhaust line connection for test gas venting
• Records are stored as a tab delineated text file (.txt format can be imported into a spreadsheet)
• Software is Windows Vista, and XP compatible
• Operates on any Pentium II or higher PC
• USB port for downloading data to a USB flash drive
• USB flash drive included

*Please note we can only ship RKI products to customers within the United States

72-5545RK Eagle Portable Monitor for LEL & PPM/O2/CO/O3/NO2 (No Probe) by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

This is the equivalent of the CG-Q58-4 from BW

Part Number: 58L-421

722-107-02-P2 Eagle 2 Portable Monitor for CO2 60% Volume (IR)/VOC?s 0 - 2,000 ppm (PID) by RKI Instruments

Continuing in its legacy of durable and reliable gas detection and monitoring systems, RKI Instruments is proud to offer a new product in its popular Eagle portable gas detector series. The Eagle 2 can monitor up to 6 different gases and is equipped with several exclusive features that can only be found with the Eagle series. In addition, its large glove friendly push buttons and LCD screen ensure an ease of use when onsite. Rated intrinsically safe, the Eagle 2 is equipped with state of the art technologies that are not available with other competitive gas detectors and monitors.

Specialty Sensors

The Eagle 2 has a variety of available specialty sensors. Workers can use a photoionization detector for low or high range VOC detection and Fence Electrode Technology for humidity and contamination resistance. An infrared sensor is available for Co2, % LEL CH4, % Volume CH4, % LEL HC, and % Volume HC. Thermal conductivity sensors are available for % Volume H2 and % Volume CH4. The unit is also compatible with the smart plug and play toxic sensors for the detection of NH3, AsH3, CI2, HCN, PH3, and SO2. With the wide variety of sensors and gas detection available, the Eagle 2 can be customized to meet almost all worksite gas detection needs.

Exclusive Features

The monitor has a long internal pump that can draw samples for up to 125 feet. The pump features a low flow auto shut off and alarm. This allows operators to respond swiftly from a safe distance. The unit is multilingual with 5 different language preferences, and features an alkaline battery life of 18 hours or a NiMH life of 20 hours. To protect the integrity of the device and the configurations, the unit can be password protected. The Eagle 2 also has standard data logging capabilities for easy research, evaluation, and site monitoring. To reduce calibration costs and time, the unit features an automatic calibration option and a single gas calibration option.

The Eagle 2 is heavily protected from environmental conditions by a weather proof, chemical resistant RFI/EMI coated high impact polycarbonate/PBT blend enclosure. The enclosure also renders the unit water and dust resistant. Because of the enclosure, the Eagle 2 can function in 2 inches of water without leakage.

Eagle 2 Specifications

The portable and durable unit is lightweight at less than 4 pounds. Its dimensions are suitable for convenient carrying (9.5?L x 5.25?W x 5.875?H), and it features a conveniently placed durable top handle. The large easy to read display has a polyurethane overlay backlights on demand and when the alarm is activated. The 2 alarm channels are fully adjustable for the user and can be password protected. With a 95 dB buzzer and 4 high intensity LEDs, the alarm is sure not to be missed. The Eagle 2 is standard with a 2 year warranty for material and workmanship and a 1 year warranty for PID sensor.

*Please note we can only ship RKI products to customers within the United States

30-0954RK-26501 Aspirator Adapter, Plate Mounted, with flow switch/Beacon 110/IR CH4 LEL in 18-0416RK j-box by RKI Instruments

Single or dual sensor system is designed to monitor gas atmospheres from extreme conditions with either temperature or pressure challenges. A powerful air aspirator can pull a sample from up to 100 feet away. The filtered and conditioned sample gas is then passed across one or two different detectors. Each detector shares a common calibration and compressed air inlet for aspirated flow. This system is fault tolerant removing the need for expensive downtimes and maintenance. The sample is diluted with air after gas sensor then returned to a common exhaust reducing the danger of potential hazardous gases entering a safe work space.

System integrity is maintained at all times using a flow fail monitoring device which provides an NO contact that activates if the sample line becomes blocked or damaged or if the air supply is removed or interrupted.

The panel can be used with direct-connect (sensors connected to an RKI controller), or with S, S2 Series, and M2A Series transmitters. All transmitters have a 4-20 mA signal for direct connection to the site DCS, PLC or site control system. If needed, RKI instruments can supply a dedicated Gas Detection Control system to provide local alarms, 4-20 mA output with a wide range of dry contacts, making the system very sophisticated and user friendly.

Integral sample filter included to remove water and dirt, automatic drain type.

RS485 Modbus output options available on the M2A transmitter.

Features

• Simple to operate
• Long life air aspirator (no moving parts)
• Extreme sample temperatures
• One or two sensors
• Inside/outside location options
• Corrosion resistant construction for extreme environments / samples
• Uses proven RKI technology
• Modular design easy to maintain
• Self draining moisture trap
• Back flush for sample line
• NEMA 4X enclosure options (stainless steel or GRP)

Industry Applications

• Flammable, oxygen, or toxic monitoring
• Wastewater
• Drinking water plants
• Gas turbine monitoring flammable and CO
• Tunnel monitoring
• Landfill borehole analyses
• Printing press exhaust solvent recovery
• Winery CO2 / O2
• Biogas Methane
• Hydrogen Sulfide "H2S" scrubber break through

*Please note we can only ship RKI products to customers within the United States

5934-0406 GDC-350 Gas Sensor Monitor, NEMA 4 Housing, NO2/NO with Display by Bacharach

Bacharach's all new GDC-350 full-featured fixed gas monitors provide superior operation - standalone or as part of a larger system utilizing the standard analog outputs. This state-of-the-art instrument can detect a wide range of gases including carbon monoxide (CO), oxygen (O2), combustible gases, refrigerants and total volatile organic compounds (TVOCs). The GDC-350 provides a unique two sensor interface, allowing for multiple gases to be detected with onboard or remote sensors. Sensors can be located integral to the unit or remotely allowing for sensors to be placed directly in areas where potential leaks can occur. Bacharach s proprietary calibration algorithms extend the amount of time required between calibrations, reducing maintenance costs and lowering the overall cost of ownership for non-critical applications.

The GDC-350 has all the features and functionality for any application. LED alarm indicators visually indicate when alarm conditions are met and an audible alarm alerts nearby personnel. An onboard alpha numeric display shows gas readings in real time for each sensor. Integral dry contact relays are available to drive external audible / visual alarms, activate fans, or connect to building management and control systems. Installation and maintenance is simple and easy, reducing overall system cost. A pre-wired plug-in option is available for out-of-the-box operation. Simply plug the unit into any standard AC outlet for immediate detection and protection.

2200-016W GMA 200-MW16 Controller, Configured for 16 Measuring Points, Supply Voltage 24 V/DC, without Power Supply by GfG

The GMA 200-MW is our most flexible and advanced gas detection system controller. The design of the GMA 200-MW ensures simple and clearly structured operation in industrial and commercial applications. The system can be configured for control of any combination of GfG gas transmitters for the measurement of an extremely wide range of toxic and combustible gases and vapors.

Flexible modular design

Each GMA 200-MW module can control up to 16 individual gas transmitters (sensors). The self-contained, IP-65 wall-mounted housing facilitates cost-effective and space-saving installation. GMA 200-MW systems are scalable, and easy to expand by adding additional controller and relay modules. Optional gateway modules allow control via remote or touch-screen computer interface.

Easy to configure

Easy-to-use, menu driven GMA 200-MW software allows configuration of sensor type, gas type, measuring point designations, units of measurement, calibration curves, and function of the comprehensive and fully programmable relays. Up to three individual or specified alarm thresholds can be programmed for each measuring point. The GMA 200-MW continuously evaluates the analog input signals of the connected detectors.

Integrated relays

GMA 200-MW systems include comprehensive and fully programmable relays. Each controller is equipped with 8 internal relays. Menu-driven software allows easy assignment of measuring points to relays, single or multiple alarms per point, alarm thresholds, configuration of collective or group alarms, zoning, fault messages and voting functions.

Relay modules

GMA 200-RW relay modules are housed in easy to install IP-65 wall mounted enclosures. Each relay module provides an additional 16 freely configurable relays. A total of four additional relay modules (for 64 additional relays) can be managed by the same GMA 200-MW system. Digital connection with the GMA 200-MW controller allows remote positioning of the relay module wherever it makes the most sense, substantially reducing cabling and installation costs.

Remote terminal displays

Relay modules are available with or without an integral display for readings and system information, making it easy to add a remote terminal wherever needed.

Optional Fieldbus-Gateways

Optional gateway modules allow integration of the GMA 200-MW system into existing company networks based on TCP/IP, Process Field Bus or Process Field Network protocols. Monitoring and system performance data are easily exported for viewing or analysis. A wifi interface can be added to the gateway to allow wireless connection with a touch screen Windows® computer or smart-phone to display or access system information.

GMA 200 power options

GMA 200-MW power options include traditional voltage inputs (2 x 24 V DC, 20-30 V), as well as operation via a redundant, uninterruptible power supply (UPS), ensuring continued operation of the gas warning system even during a power outage.

Integral alarms

The GMA 200-MW includes built-in bright LED strobe light and loud audible alarms.

LED indicator lights

The status of the GMA 200-MW system (including operation, fault, service, alarm and relay status) is shown via LEDs. Individual LED indicators identify the type and severity of the alarm condition, (FLT, AL1, AL2, AL3), and any relays activated by the condition, (R1 through R8).

Datalogging standard

Measured values, mean values, alarm events and faults are permanently stored on a microSD memory card.

Graphical display

Currently measured values are displayed on a backlit, graphical LCD. In the event of an alarm the display changes color from green to red, and highlights the affected channels.

Five buttons enable operation at the GMA 200-MW controller. The main functions of the keyboard are the acknowledgement of alarms and the menu-driven operation. Information on the status of the controller, detector and the relays can be retrieved in the operating menu.

Operation via keypad

Operation of the GMA 200-MW is through easy-to-use menus, and a simple 5 button interface for alarm acknowledgement, and viewing information on the status of the gas warning system, detectors and relays. The intuitive push-button controls make it easy to navigate through additional screens of information. The integrated display enables the reading of alarm levels through the controller LCD for easy hazard assessment.

Configuration

A built-in USB port in the GMA 200-MW is used for connection to the configuration software. GMA 200-MW systems connected through a Fieldbus gateway can be remotely connected with a GfG factory service center for configuration, diagnostic or service evaluation.

Easy and convenient service

GfG offers full after-the-sale commissioning and field service support.

Additional modules available in IP-65 wall-mounting housings

• External relay module: GMA 200-RW
• Independent power supply: GMA 200-UPS
• Continuous, motorized pump sampling unit: GMA 200-ASV
• Fieldbus gateway: GMA 200-GW

Features

• Advanced and flexible controller for combustible, O₂ and toxic gas
• IP-65 wall-mounting housing, with integral audible and LED alarms
• Flexible, reliable and economic
• Up to 16 transmitters per GMA 200-MW controller in any combination
• Freely programmable relays
• Clearly structured, easy-to-use push-button interface
• Backlit graphic LCD changes color to indicate alarm
• Connect to other measurement devices with 4-20 mA output

500-9 Handheld Combustion Efficiency Emissions Analyzer includes O2, CO, NO, NO2, NOx, Temperature, Draft, Combustibles, Printer, -Tooth, Thermoelectric Condenser (Sample Conditioning System) by Enerac

Enerac invented the first electronic portable multi-parameter combustion analyzer in 1979 (in the USA). Enerac still services this analyzer as well as all others Enerac has manufactured. The Enerac Model 500 is a low-cost, easy to use (no technical expertise needed) portable combustion efficiency emissions analyzer. The Enerac 500 is perfect for determining the efficiency of a combustion source as well as for collecting advanced emissions data for internal use, or for local, state and federal emissions reporting requirements.

The Enerac 500 is perfect for testing various combustion sources, such as boilers, burners, engines, turbines, generators, kilns, dryers, heaters and ovens (just to name a few). Equally, with a simple combustion efficiency test, or a more advanced combustion emissions test, the Enerac 500 is designed to provide years of trouble-free service. It is flexible enough to be tailored to meet your specific needs, yet simple enough to be completely maintained in the field. Advanced design, rugged construction and an impressive array of options are its hallmark. Constructed as a field work-horse the Enerac 500 can be upgraded (adding sensors and options to the same unit) to meet your changing needs at any time.

Introduction

The Enerac 500 provides a comprehensive range of automatic emissions calculations, advanced Enercom Windows Software, two-way communications and factory support. From low NOx burners, (0.1ppm NOxresolution) to large rich burn engines (5,000ppm (NOx)/20,000ppm CO) the Enerac 500 is designed to help meet your needs of various monitoring applications at an affordable price.

The Enerac 500 handheld combustion efficiency emissions analyzer, is our newest, low cost, Emissions-Monitoring System, utilizing standard electrochemical sensors. It is designed to help you meet the challenges of a rapidly changing regulatory environment. It is easy to use, comprehensive (O2-CO-NO-NO2-(NOx), SO2, Combustibles, Stack Temperature, Draft), and flexible.

• A micro-sized Combustion-Efficiency analyzer and Emissions-Monitoring System
• Thermoelectric Condenser / Peltier Cooler (sample conditioning system for proper detection and measurement of NO2 and/or SO2 gasses
• Powered by 4xAA Rechargeable batteries
• Built-in Thermal Printer: 2" Character-type
• Our Enercom Windows Software included
• USB and Serial Ports included. Bluetooth Wireless (optional)

Rugged

The Enerac 500 is designed for years of trouble-free service. Housed in a rugged, lightweight aluminum case, its modular design allows end-users the ability to replace a battery or sensor, in a matter of seconds. Reducing both downtime and costs.

• Rugged lightweight aluminum case
• Work-horse of the industry
• Won't warp or crack like plastic models
• Small, lightweight and tough
• 2 Year Warranty
• 24 Hour Service
• Best service and support in the industry

Comprehensive

The Enerac 500 provides an extensive range of data management, and support options. It not only (automatically) performs complicated emission calculations, it can even allow the user the ability to identify specific data sets with a specific customer, dramatically reducing retrieval and processing costs.

Enerac 500 is compatible with Enerac's advanced Enercom for Windows ™ software. All parameters can be continuously displayed; Minimum, Maximum, Averages and Standard Deviations calculated; Multiple plots and graphs can be viewed or printed. With the Enercom software, data management and report writing is now a snap. With the Enerac 500, help is never more than a phone call or email away.

Affordable

With all these capabilities the Enerac 500 is surprisingly affordable.

• Buy only what you need and add options later
• Always upgradeable (anytime)!
• Free software and accessories
• Receive a generous trade-in allowance on your old analyzer
• Loaners available at no charge.

Compliance Level

The Enerac 500 can be configured to a compliance-level analyzer with addition of several key features. The Enerac 500 has the ability to produce Total NOx data for one. With both the NO and NO2 sensors Total NOxis obtained (NOx)=NO+NO2 on stationary combustion sources). The ability to also configure the 500 with High Sensativity sensors allows extreme accuracy over the sensors shorter range etc. Additionally, the 500 has the option to have the Thermoelectric Condenser (also called Peltier Cooler) option installed. This is a sample conditioning system (usually found on our competitors larger more expensive units) essential for proper NO2 and or SO2 gas detection and measurement. With the final addition of the viton hose, sample quality is maintained and compliance level data obtained. Therefore, the Enerac 500 is perfect for meeting your local, state and federal regulatory emissions compliance requirements.

• Free data collection software
• Time-stamped internal data storage
• Total NOx (NO and NO2)
• High Sensitivity / Low Range Sensors Available
• Viton and Teflon hose options
• Sample Conditioning System (for proper NO2 and/or SO2 gas detection and measurement)
• Field replaceable sensors
• Easy field calibrations (if desired)
• Comply with local, state and federal emissions requirements

In a world of downsizing, and increasing workloads, the Enerac 500 can help you simplify your job. With a broad array of available options, the Enerac 500 will provide you with the capabilities you need, when you need them, all within your budget.

1418-170 Micro IV Single Gas Detector with 1-Year Single Gas Detector Warranty Ammonia (NH3), 0 -500 ppm by GfG

Durable, compact design

Widest Range of sensors

Easy Operation

Up to six months of battery life

Clip-on attachment

Optional motorized pump

Large graphic display

Audible, vibrating and visual alarms

Lifetime warranty

DS220 docking station

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Standard Accessories

• Micro IV detector
• Specified Sensor
• Alkaline Battery
• Rubber Boot
• Manual

44521R Gasurveyor 521R 4 Button Portable Gas Detector - LEL, VOL, O2 - Rechargeable by GMI

The GMI Gasurveyor 500 series is the most flexible range of gas detectors available today. By simple selection of hardware and software options the instrument can be readily configured to suit your exact application.

Features

• Measures flammable, oxygen and toxic gases
• Dual mode operation - Combustible Gas Indicator (CGI) / ConfinedSpace Monitor (CSM)
• Rechargeable or alkaline battery options
• Approved to European and North American safety standards
• Extremely robust anti-static case
• Simple to use
• Built-in sampling pump as standard
• Large LCD with automatic backlighting in low level light conditions
• Compatible with the GMI range of Auto Calibration Systems
• Audible / visual alarms for all gas ranges
• Fault alarms for low flow, low battery etc.
• Probes for a wide range of applications

Includes

• G500 carrying case
• Harness
• Hex driver
• 1.5Mt clear sample line
• User manual
• Probe handle
• 35 cm probe (solid end)
• Sample line adaptor
• Dry cell batteries (not USA) or NiCad pack and cotton filters (20).

5201-2031 GDC-150 Gas Sensor Transmitter, NEMA 4 Housing, MOS Refrigerant Sensor by Bacharach

The all new GDC-150 transmitter from Bacharach offers detection and protection for a wide range of hazards including toxic gases such as carbon monoxide (CO), oxygen depletion, combustible gases, refrigerant leaks and total volatile organic compounds (TVOCs). Analog interfaces allow the transmitter to be connected back to Bacharach's GDA Series of controllers (or any other gas detection controller), building management systems or control systems. The GDC-150 features 4-20 mA or 0-10 VDC linear output signals, an automatic thermal resetting fuse, RoHS compliant circuit boards and LED indicators for power and open loop.

The onboard alarm LED's indicate when alarm threshold values are exceeded. The unit can be ordered with an optional alpha numeric LED display that shows gas concentrations in real time while alarm relays alert personnel of potential dangers, avoiding incidents and potential hazards.

The GDC-150 is packaged in a rugged, polycarbonate housing for both indoor and outdoor applications. When leaks occur, the GDC-150 sensors respond quickly and accurately to protect people and property. Automated calibration and simple maintenance procedures performed in the field allow for continuous operation and assurance that areas are monitored and protected at all times.

XT-X00M-Y-AU GasAlertMax XT II 2 Gas Detector, Oxygen (O2), Carbon Monoxide (CO) - Yellow Housing, AU Version (Australia) by BW Technologies

GasAlertMax XT II is the safest and most economical choice for multi-gas detection systems. Utilizing the most advanced technology on the market, the GasAlertMax accurately and reliably monitors up to four hazardous conditions, and offers a simple user friendly device for easy operation. Its standard safety features and compatibility with other instruments ensure that the gas detector is the best instrument for gas monitoring compliance.

GasAlertMax XT II specifications

The lightweight and portable unit is approximately 11.5 ounces, and features the latest technology allowing for a compact design. With an operational temperature range of -4 to 122 degrees Fahrenheit, the monitor is designed to function effectively in many harsh conditions. The cautionary yellow outer shell helps to ensure that the gas detector is carried with the user not left onsite. Additionally, the durable casing is resistant to water and features a built-in concussion proof boot.

Triple alarm system

The GasAlertMax XT II features a triple alarm system designed to alert users of potentially hazardous conditions. When the gas sensors detect specified levels of H2S, CO, O2, or combustible gases, the instrument will begin the triple alarm alert and notify users and those nearby. The device indicates these dangers with a vibrating alarm, an ultra bright visual alarm, and an audible alarm of over 95 decibels. The alarms are also designed to alert users of administrative needs such as battery replacement.

GasAlertMax XT II features

The GasAlertMax XT II has multi-language support features in English, French, Spanish, German, and Portuguese. The gas detector also has state of the art block detection with semi-conductor pressure sensor, and standard data and event logging. Accessories such as the belt holster, multi-unit cradle charger, and concussion proof boot are also available.

Upon activation, the unit will automatically test sensors, pumps, battery, and circuitry. For additional test and calibration, the GasAlertMax XT II is compatible with the MicroDock II automated test and calibration system and Fleet Manager II. Improving on its functionality, the unit is customizable. Users can change options for forced calibration and tests, safety locks, alarm setpoints, safe display mode, language choices, start-up message, and more.

The easy to read LCD screen displays continuous information about real-time gas concentrations and alarms. To maintain simplicity and ease of use, the GasAlertMax XT II also features a user and glove friendly one touch button for operation. The no-frills design has an added benefit of minimizing cost and user training. This simple, portable, and compact detector is the best instrument for confined spaces or potentially dangerous worksites.

Highest standards of reliability

The typical batter life ranges between 8 and 13 hours depending on the temperature. The durable and long lasting batteries can fully recharge in approximately 6 hours. The GasAlertMax XT II and its sensors feature a standard two year warranty. With safety and reliability as a top priority, BW Technologies has developed the multigas detector to utilize the most advanced technology on the market, while maintaining its simplicity and portability. When working in settings with possible gas exposure, users can be certain that the gas levels are being accurately and reliably monitored with the best technology available.

Part Number: XTX00MYAU

RI-215A-115 RI-215A CO2 Detector Head, 115 VAC Powered by RKI Instruments

The RI-215 series of IR CO2 montitors are widely used in the measurement and control of CO2 levels in a variety of applications where CO2 monitoring or detection is required. A highly accurate, RKI non-dispersive infrared absorption sensor is used to provide direct measurements through diffusion or sample draw monitors, and activate alarms or control ventilation systems based on preset CO2 levels. Each model provides a digital readout in parts per million of CO2 providing precise measurement and direct visual indication of gas levels. A 4-20 mA output is provided to send a signal to a fire panel or other PLC system and a relay is available to trip an alarm or activate a ventilation system.

Three levels of measurement are provided: 0-2,000 ppm (ASHRAE 1969 IAQ max PEL), 0-5,000 ppm (leak detection of CO2 storage tanks) and 0-9,999 ppm. The RI-215A runs on 24 VAC or 24 VDC and the RI-215D with sample drawing pump runs on 115 VAC or 220 VAC. Each are designed for indoor use only and supplied in a NEMA 12 enclosure that is easily accessible for calibration, service, and continuous monitoring. RKI offers additional monitors with higher measurement levels in portable or fixed installation applications. Please contact an RKI authorized representative for more information on other CO2 monitors available

Features

• Easy to read LCD digital display
• Compact, lightweight and easy installation
• Highly reliable non-dispersive infrared detection method
• Recorder output signal
• Automatic control of ventilation systems
• Alarm contact output provided
• 4-20 mA output provided
• Diffusion or sample draw versions available

Applications

• Meets ASHRAE 1969 IAQ Standard of 2,000 ppm max PEL
• Detection of CO2 for NFPA 12 Regulations-CO2 storage tank leaks
• Green houses, wineries, breweries, food processing, indoor air quality, and other industry applications

*Please note we can only ship RKI products to customers within the United States

66-6306-75-R T3A Sensor/Transmitter with j-box, Ammonia (NH3), 0-75 ppm with 2 alarm relays by RKI Instruments

The T3A Series Gas Detector ambient air hazardous gas detector is a versatile assembly that uses an electrochemical, infrared, catalytic bead sensor element to detect a variety of gases. Wired power (12 to 35 VDC) with 4-20 mA analog and RS-485 Modbus outputs standard. Magnetic switches allow for non-intrusive calibration while in the field as well as full system settings and diagnostics.

Features

• Electrochemical, Infrared, catalytic bead sensor element
• Wire powered (3-Wire), 12 to 35 VDC operating voltage
• Digital Modbus output
• Operating temperature range -40°C to +54°C Graphical LCD with LED backlight
• 3 Push-button interface (ADD, MENU, SUB) with 3 corresponding magnetic, non-intrusive switches
• 2 Individually configurable alarms
• 2 Front panel LED indicators (amber and red)
• 2 Optional fully programmable alarm relays (dry contacts)
• Output options: 4-20mA (3-wire) analog, RS-485 modbus

Industry Applications

• Petrochemical plants, Refineries
• Water & wastewater treatment plants
• Pulp & paper mills
• Manufacturing facilities
• Chemical plants

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

RI-215A-03 RI-215A IR Diffusion Detector Head for CO2, 0 - 5% by RKI Instruments

The RI-215 series of IR CO2 montitors are widely used in the measurement and control of CO2 levels in a variety of applications where CO2 monitoring or detection is required. A highly accurate, RKI non-dispersive infrared absorption sensor is used to provide direct measurements through diffusion or sample draw monitors, and activate alarms or control ventilation systems based on preset CO2 levels. Each model provides a digital readout in parts per million of CO2 providing precise measurement and direct visual indication of gas levels. A 4-20 mA output is provided to send a signal to a fire panel or other PLC system and a relay is available to trip an alarm or activate a ventilation system.

Three levels of measurement are provided: 0-2,000 ppm (ASHRAE 1969 IAQ max PEL), 0-5,000 ppm (leak detection of CO2 storage tanks) and 0-9,999 ppm. The RI-215A runs on 24 VAC or 24 VDC and the RI-215D with sample drawing pump runs on 115 VAC or 220 VAC. Each are designed for indoor use only and supplied in a NEMA 12 enclosure that is easily accessible for calibration, service, and continuous monitoring. RKI offers additional monitors with higher measurement levels in portable or fixed installation applications. Please contact an RKI authorized representative for more information on other CO2 monitors available

Features

• Easy to read LCD digital display
• Compact, lightweight and easy installation
• Highly reliable non-dispersive infrared detection method
• Recorder output signal
• Automatic control of ventilation systems
• Alarm contact output provided
• 4-20 mA output provided
• Diffusion or sample draw versions available

Applications

• Meets ASHRAE 1969 IAQ Standard of 2,000 ppm max PEL
• Detection of CO2 for NFPA 12 Regulations-CO2 storage tank leaks
• Green houses, wineries, breweries, food processing, indoor air quality, and other industry applications

*Please note we can only ship RKI products to customers within the United States

72-5528RK Eagle Portable Monitor for LEL & PPM/O2/CO/NH3/PH3 by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

72-5624RK Eagle Portable Monitor for LEL & PPM/O2/CO/O3/NH3 (No Probe) by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

30-0954-201-CSA Aspirator Adapter, Plate Mounted, with Flow Switch for one CSA LEL Sens in 18-0431RK/18-0432RK J-Box by RKI Instruments

Single or dual sensor system is designed to monitor gas atmospheres from extreme conditions with either temperature or pressure challenges. A powerful air aspirator can pull a sample from up to 100 feet away. The filtered and conditioned sample gas is then passed across one or two different detectors. Each detector shares a common calibration and compressed air inlet for aspirated flow. This system is fault tolerant removing the need for expensive downtimes and maintenance. The sample is diluted with air after gas sensor then returned to a common exhaust reducing the danger of potential hazardous gases entering a safe work space.

System integrity is maintained at all times using a flow fail monitoring device which provides an NO contact that activates if the sample line becomes blocked or damaged or if the air supply is removed or interrupted.

The panel can be used with direct-connect (sensors connected to an RKI controller), or with S, S2 Series, and M2A Series transmitters. All transmitters have a 4-20 mA signal for direct connection to the site DCS, PLC or site control system. If needed, RKI instruments can supply a dedicated Gas Detection Control system to provide local alarms, 4-20 mA output with a wide range of dry contacts, making the system very sophisticated and user friendly.

Integral sample filter included to remove water and dirt, automatic drain type.

RS485 Modbus output options available on the M2A transmitter.

Features

• Simple to operate
• Long life air aspirator (no moving parts)
• Extreme sample temperatures
• One or two sensors
• Inside/outside location options
• Corrosion resistant construction for extreme environments / samples
• Uses proven RKI technology
• Modular design easy to maintain
• Self draining moisture trap
• Back flush for sample line
• NEMA 4X enclosure options (stainless steel or GRP)

Industry Applications

• Flammable, oxygen, or toxic monitoring
• Wastewater
• Drinking water plants
• Gas turbine monitoring flammable and CO
• Tunnel monitoring
• Landfill borehole analyses
• Printing press exhaust solvent recovery
• Winery CO2 / O2
• Biogas Methane
• Hydrogen Sulfide "H2S" scrubber break through

*Please note we can only ship RKI products to customers within the United States