Pump Inlet

1450-924 G400 Motorized Smart Pump Rechargeable with LED by GfG

Optimized Alarm System

The new G400 MP-2 pump continuously communicates with the G450/G460 gas detector. This interaction allows fault indication via the detector display. Alarms such as low battery, blocked sampling line or interrupted power fault are shown on the display and activate a visual and audible alarm on the monitor.

Various Applications

Gas samples can be taken from a distance of up 100 meters (over 300 feet) at a typical draw rate of 0.5 liters per minute.

Superior Flexibility

The G400 MP-2 is the only detachable pump on the market today which will allow for operation in both diffusion mode and remote sample-draw mode. Simply slide the shutter to turn the pump on or off. When the pump is on, the shutter covers the diffusion inlets and exposes them when the pump is switched off.

The G400 MP-2 features a high efficiency redundant filter system in addition to a standard external probe with dust and hydrophobic filters.

Independent Power Supply

The G400 MP-2 is operated by its own power supply, independent of the gas detector. The power supply of the pump allows for up to 10 hours of continuous operation.

Features

• Optimized alarm system: Visual alarm via the G450/G460 display and alarm LEDs, Audible alarm via the G450/G460, Vibration alarm via the G450/G460
• Allows monitor to be used in either pump or diffusion mode
• Independent power supply (does not reduce instrument battery capacity)
• 300 feet (100 meter) remote sampling capability

Includes

• 10' of Tubing
• Probe with Filters

1450-402R-3X 3 Unit DS402 Docking Station System by GfG

Easy operation

The operation of the DS400 docking station couldn't be any easier. Simply put the G450 or the G460 in the dock and the system will take over from there. The DS400 automatically performs a full functional test including fresh air calibration, bump test, extensive sensor tests, alarm tests and optionally performs an automatic AutoCal® calibration.

Extensive diagnostics

The DS400 is designed to go beyond the traditional basic docking station tests and includes sensor diagnostics tests such as T50 and T90. After all, what good is a sensor that can respond to gas when it takes too long to get there? With the DS400 you can have confidence with this added level of safety.

Automatic charging

After all tests have been completed the DS400 will automatically start the charging process of the detector or you may remove and begin using it. In case the detectors battery condition is insufficient to complete a test the DS400 will charge the instrument before performing the test.

Record Keeping

A good instrument gas detection maintenance program is not complete without equally good records keeping. Whether you choose to download or maintain the records on a PC or network or your preference is to leave it to the docking station, the DS400 is the right choice.

The DS400 can retain as many as 2 million complete diagnostics in memory with maximum memory installed. That is over 50 years of data even if testing 100 detectors every single day!

Reduced cost of ownership

The DS400 is designed to reduce the cost of ownership every step of the way. The built in pump has variable flow control to reduce the amount of gas consumed during the test. The DS400 is even smart enough take advantage of the gas remaining in the tubing after the previous test was completed.

PC communication

The DS400 comes complete with USB interface cable and download software. The SD card may also be downloaded using a standard SD card reader.

Maintenance certificates

The DS400 software includes a module to quickly print official calibration or bump test certificates. Simply download the records from the DS400 and start the "Certificate Generator" it takes only seconds!

Features

• Fully automatic functional bump test and calibration
• Automatic test of alarms
• Automatic charging
• Automatic record keeping
• Simple pass / fail indication
• Saves last calibration and bump test records in detector for easy retrieval of maintenance record in the field
• No computer necessary
• Up to 2,000,000 records in memory
• Cascade multiple docking stations
• Saves times, gas and efforts for lower cost of ownership
• Print official calibration certificates

Features

• Single gas inlet
• Double cradle
• Base plate
• Unit-to-unit power adapters
• Ethernet cables
• Standard accessories
• One demand flow regulator (DFR)

1450-404-DS404-3X 3 Unit DS404 Docking Station System by GfG

Easy operation

The operation of the DS404 docking station couldn't be any easier. Simply put the G450 or the G460 in the dock and the system will take over from there. The DS404 automatically performs a full functional test including fresh air calibration, bump test, extensive sensor tests, alarm tests and optionally performs an automatic AutoCal® calibration.

Extensive diagnostics

The DS404 is designed to go beyond the traditional basic docking station tests and includes sensor diagnostics tests such as T50 and T90. After all, what good is a sensor that can respond to gas when it takes too long to get there? With the DS404 you can have confidence with this added level of safety.

Automatic charging

After all tests have been completed the DS404 will automatically start the charging process of the detector or you may remove and begin using it. In case the detectors battery condition is insufficient to complete a test the DS404 will charge the instrument before performing the test.

Record Keeping

A good instrument gas detection maintenance program is not complete without equally good records keeping. Whether you choose to download or maintain the records on a PC or network or your preference is to leave it to the docking station, the DS404 is the right choice.

The DS404 can retain as many as 2 million complete diagnostics in memory with maximum memory installed. That is over 50 years of data even if testing 100 detectors every single day!

Reduced cost of ownership

The DS404 is designed to reduce the cost of ownership every step of the way. The built in pump has variable flow control to reduce the amount of gas consumed during the test. The DS404 is even smart enough take advantage of the gas remaining in the tubing after the previous test was completed.

PC communication

The DS404 comes complete with USB interface cable and download software. The SD card may also be downloaded using a standard SD card reader.

Maintenance certificates

quickly print official calibration or bump test certificates. Simply download the records from the DS404 and start the "Certificate Generator" it takes only seconds!

Features

• Four test gas ports
• Fully automatic functional bump test and calibration
• Automatic test of alarms
• Automatic charging
• Automatic record keeping
• Simple pass / fail indication
• Cascade multiple docking stations
• Saves last calibration and bump test records in detector for easy retrieval of maintenance record in the field
• No computer necessary
• Up to 2,000,000 records in memory
• Saves times, gas and efforts for lower cost of ownership
• Print official calibration certificates

Includes

• Four Gas Inlets
• Single Cradle
• Base Plate
• Unit-to-unit Power Adapters
• Ethernet Cables
• Standard Accessories

1450-405 DS404 Four Inlet Multi-gas Docking Station - Instrument & Pump by GfG

Easy operation

The operation of the DS404 docking station couldn't be any easier. Simply put the G450 or the G460 in the dock and the system will take over from there. The DS404 automatically performs a full functional test including fresh air calibration, bump test, extensive sensor tests, alarm tests and optionally performs an automatic AutoCal® calibration.

Extensive diagnostics

The DS404 is designed to go beyond the traditional basic docking station tests and includes sensor diagnostics tests such as T50 and T90. After all, what good is a sensor that can respond to gas when it takes too long to get there? With the DS404 you can have confidence with this added level of safety.

Automatic charging

After all tests have been completed the DS404 will automatically start the charging process of the detector or you may remove and begin using it. In case the detectors battery condition is insufficient to complete a test the DS404 will charge the instrument before performing the test.

Record Keeping

A good instrument gas detection maintenance program is not complete without equally good records keeping. Whether you choose to download or maintain the records on a PC or network or your preference is to leave it to the docking station, the DS404 is the right choice.

The DS404 can retain as many as 2 million complete diagnostics in memory with maximum memory installed. That is over 50 years of data even if testing 100 detectors every single day!

Reduced cost of ownership

The DS404 is designed to reduce the cost of ownership every step of the way. The built in pump has variable flow control to reduce the amount of gas consumed during the test. The DS404 is even smart enough take advantage of the gas remaining in the tubing after the previous test was completed.

PC communication

The DS404 comes complete with USB interface cable and download software. The SD card may also be downloaded using a standard SD card reader.

Maintenance certificates

quickly print official calibration or bump test certificates. Simply download the records from the DS404 and start the "Certificate Generator" it takes only seconds!

Features

• Four test gas ports
• Fully automatic functional bump test and calibration
• Automatic test of alarms
• Automatic charging
• Automatic record keeping
• Simple pass / fail indication
• Cascade multiple docking stations
• Saves last calibration and bump test records in detector for easy retrieval of maintenance record in the field
• No computer necessary
• Up to 2,000,000 records in memory
• Saves times, gas and efforts for lower cost of ownership
• Print official calibration certificates

1450-405R2 DS404 Four Inlet Multi-gas Docking Station - Double Cradle (Instrument & Pump) with 2 Regulators by GfG

Easy operation

The operation of the DS404 docking station couldn't be any easier. Simply put the G450 or the G460 in the dock and the system will take over from there. The DS404 automatically performs a full functional test including fresh air calibration, bump test, extensive sensor tests, alarm tests and optionally performs an automatic AutoCal® calibration.

Extensive diagnostics

The DS404 is designed to go beyond the traditional basic docking station tests and includes sensor diagnostics tests such as T50 and T90. After all, what good is a sensor that can respond to gas when it takes too long to get there? With the DS404 you can have confidence with this added level of safety.

Automatic charging

After all tests have been completed the DS404 will automatically start the charging process of the detector or you may remove and begin using it. In case the detectors battery condition is insufficient to complete a test the DS404 will charge the instrument before performing the test.

Record Keeping

A good instrument gas detection maintenance program is not complete without equally good records keeping. Whether you choose to download or maintain the records on a PC or network or your preference is to leave it to the docking station, the DS404 is the right choice.

The DS404 can retain as many as 2 million complete diagnostics in memory with maximum memory installed. That is over 50 years of data even if testing 100 detectors every single day!

Reduced cost of ownership

The DS404 is designed to reduce the cost of ownership every step of the way. The built in pump has variable flow control to reduce the amount of gas consumed during the test. The DS404 is even smart enough take advantage of the gas remaining in the tubing after the previous test was completed.

PC communication

The DS404 comes complete with USB interface cable and download software. The SD card may also be downloaded using a standard SD card reader.

Maintenance certificates

quickly print official calibration or bump test certificates. Simply download the records from the DS404 and start the "Certificate Generator" it takes only seconds!

Features

• Four test gas ports
• Fully automatic functional bump test and calibration
• Automatic test of alarms
• Automatic charging
• Automatic record keeping
• Simple pass / fail indication
• Cascade multiple docking stations
• Saves last calibration and bump test records in detector for easy retrieval of maintenance record in the field
• No computer necessary
• Up to 2,000,000 records in memory
• Saves times, gas and efforts for lower cost of ownership
• Print official calibration certificates

PH0100SIUN23 pH Safe 1 Neutralization cartridge by Sauermann

The pH Safe 1 Neutralization Cartridge is safe, easy-to-install and eco-friendly. It's capable of neutralizing up to 200 gallons (800 liters) of acidic condensates at pH3. The pH Safe 1 has been specifically designed to treat condensates produced by gas condensing boilers for use with Sauermann centrifugal tank pumps.

• Preserves the plumbing system and the environment
• Prevents damage to concrete and plastics
• Prevents corrosion on metal parts
• Easy-to-install and replaces; fits right into the tank pump inlet

1450-922 G400 Motorized Smart Pump Rechargeable by GfG

Optimized Alarm System

The new G400 MP-2 pump continuously communicates with the G450/G460 gas detector. This interaction allows fault indication via the detector display. Alarms such as low battery, blocked sampling line or interrupted power fault are shown on the display and activate a visual and audible alarm on the monitor.

Various Applications

Gas samples can be taken from a distance of up 100 meters (over 300 feet) at a typical draw rate of 0.5 liters per minute.

Superior Flexibility

The G400 MP-2 is the only detachable pump on the market today which will allow for operation in both diffusion mode and remote sample-draw mode. Simply slide the shutter to turn the pump on or off. When the pump is on, the shutter covers the diffusion inlets and exposes them when the pump is switched off.

The G400 MP-2 features a high efficiency redundant filter system in addition to a standard external probe with dust and hydrophobic filters.

Independent Power Supply

The G400 MP-2 is operated by its own power supply, independent of the gas detector. The power supply of the pump allows for up to 10 hours of continuous operation.

Features

• Optimized alarm system: Visual alarm via the G450/G460 display and alarm LEDs, Audible alarm via the G450/G460, Vibration alarm via the G450/G460
• Allows monitor to be used in either pump or diffusion mode
• Independent power supply (does not reduce instrument battery capacity)
• 300 feet (100 meter) remote sampling capability

Includes

• 10' of Tubing
• Probe with Filters

Part Number: HU-IN

2203000 GMA200-MGSS/V0, Standard base unit, for 1 suction point, without changeover valve for test gas supply, with electronically controlled pump with flow control for 1-3 sensor units, 1x CC-sensor, 2x EC or IR-sensors by GfG

GfG Instrumentation is a global leader in the design and manufacture of gas detection products used to protect people, facilities and the environment. For over 50 years we have provided gas detection solutions for life critical health and safety applications. Our innovative and reliable gas warning and measurement systems provide the industry benchmark for accuracy, dependability, and cost-effective ownership.

Complex industrial processes and plants are still challenges for safety measures. Sealed spaces, pipelines and further hardly accessible areas as well as extreme ambient conditions are special demands on gas detection for process monitoring and the safety of plants and persons.

With the GMA 200-MGSS gas sampling system, GfG masters these challenges by combining the reliable GMA 200 controller with internal sensors and a electronic gas sampling feed pump. Samples of combustible and toxic gases can be taken from critical areas, processed and analyzed. Afterwards the gas sample can be fed back in the process or in safe areas.

Field-tested analysis

The gas sampling system is based on the GMA 200 controller and provides all of its' advantages:

Integrated relays

GMA 200-MGSS system includes comprehensive and fully programmable relays. Each controller is equipped with eight internal relays. Six of these relays can be freely programmed for alarms and further safety measures. This offers countless possibilities.

Clear display elements

The LEDs display the state of the gas sampling system, the operation mode, errors or service needed. In addition, the GMA 200-MGSS has a LCD graphical display, which continuously shows the current measurement data. In the case of an alarm, the red backlight of the display, the alarm LEDs as well as the relay LEDs will be activated and the active alarm will be shown in the display.

Operation via keyboard

Operation of the GMA 200-MGSS is through easy-to-use menus, and a simple 5 button interface for alarm acknowledgement, and viewing information on the status of the gas warning system, detectors and relays. The intuitive push-button controls make it easy to navigate through additional screens of information. The integrated display enables the reading of alarm levels through the controller LCD for easy hazard assessment.

Modular structure

The GMA 200-MGSS offers a wide range of flexibility and adjusts to your requirements. Due to the modular structure additional components can be added to the base version to perform measurement tasks.

Flame arrestor

If the gas sample is taken from potentially explosive atmospheres, they have to be protected from flames, which can be caused by sparks of electrical origin. For this purpose a flame arrestor can be integrated into the GMA 200-MGSS as an option. In the case that the gas will be led back to the potentially explosive atmospheres a further flame arrestor can be installed on the output of the GMA 200-MGSS.

Condensate trap

Gas samples may include pollution like dust particles as well as condensate. These impurities could damage the integrated sensors. The condensate trap filters the gas samples and greatly increases the lifetime of the sensors.

Water barrier

The water barrier prevents the unintentional intake of water or other liquids while taking gas samples.

Cooling coil

When analyzing gases from areas with extreme temperature, the sample must be cooled to prevent sensor damage.

Valve switching

The additional gas inlet for calibration gas or purge gas makes cleaning the gas channel and calibration of the device easy.

Features

• Efficient alternative to high-priced sampling systems
• Electronic sampling pump
• Fully automated flow control
• Internal gas distributor for one catalytic combustion sensor and two electrochemical sensors
• Condensate trap, water filter and flame arrestor

1450-405-3X 3 Unit DS405 Docking Station System by GfG

Easy operation

The operation of the DS404 docking station couldn t be any easier. Simply put the G450 or the G460 in the dock and the system will take over from there. The DS404 automatically performs a full functional test including fresh air calibration, bump test, extensive sensor tests, alarm tests and optionally performs an automatic AutoCal® calibration.

Extensive diagnostics

The DS404 is designed to go beyond the traditional basic docking station tests and includes sensor diagnostics tests such as T50 and T90. After all, what good is a sensor that can respond to gas when it takes too long to get there? With the DS404 you can have confidence with this added level of safety.

Automatic charging

After all tests have been completed the DS404 will automatically start the charging process of the detector or you may remove and begin using it. In case the detectors battery condition is insufficient to complete a test the DS404 will charge the instrument before performing the test.

Record Keeping

A good instrument gas detection maintenance program is not complete without equally good records keeping. Whether you choose to download or maintain the records on a PC or network or your preference is to leave it to the docking station, the DS404 is the right choice.

The DS404 can retain as many as 2 million complete diagnostics in memory with maximum memory installed. That is over 50 years of data even if testing 100 detectors every single day!

Reduced cost of ownership

The DS404 is designed to reduce the cost of ownership every step of the way. The built in pump has variable flow control to reduce the amount of gas consumed during the test. The DS404 is even smart enough take advantage of the gas remaining in the tubing after the previous test was completed.

PC communication

The DS404 comes complete with USB interface cable and download software. The SD card may also be downloaded using a standard SD card reader.

Maintenance certificates

quickly print official calibration or bump test certificates. Simply download the records from the DS404 and start the "Certificate Generator" it takes only seconds!

Features

• Four test gas ports
• Fully automatic functional bump test and calibration
• Automatic test of alarms
• Automatic charging
• Automatic record keeping
• Simple pass / fail indication
• Cascade multiple docking stations
• Saves last calibration and bump test records in detector for easy retrieval of maintenance record in the field
• No computer necessary
• Up to 2,000,000 records in memory
• Saves times, gas and efforts for lower cost of ownership
• Print official calibration certificates

Features

• Four gas inlet
• Double cradle
• Base plate
• Unit-to-unit power adapters
• Ethernet cables
• Standard accessories

CB-0005 CheckBox IMH Hub with 8 Gas Inlets and Ten Outlets by Crowcon

Portable gas detector maintenance and calibration requires cost and manpower resources, and is subject to operator inconsistency. Checkbox IMH automates daily testing, calibration, configuration control and data gathering, ensuring consistent and correct methodology at all times whilst reducing the cost of ownership.

Simple and intuitive to use Checkbox IMH simplifies the control of gas detector status and enhances operational reliability and efficiency of use.

Simple

• Visual user interface
• Mouse or Touch Screen control
• Clear displays of instrument status
• Uses standard instrument interfaces
• Suitable for both pumped and diffusion instruments

Assurance

• Daily gas testing
• Automatic calibration
• Automatic report generation
• Automation ensures correct methodology
• Automatic selection of optimum gases

Traceability

• Full records of all gas tests and calibrations
• Complete activity record for each instrument
• Original and latest configuration storage
• Data and event log file archiving Ability to input batch or lot numbers for gases

Flexible

• Five or ten instrument versions available
• Single or multigas mixtures
• Up to eight gas inlets
• Any combination of compatible monitors
• User determined functionaity

C01360-1 Detective NET 433MHz (with 0.7M of cable) by Crowcon

Detective Wireless is a module that can replace interconnecting cables for Detective+. Detective Wireless will transmit gas alert signals and other alarms wirelessly between Detective units using a 433MHz signal up to 100 metres in distance.

Detective Wireless uses the proven RICOCHET mesh network. When establishing a mesh network, Detective Wireless automatically selects the best line to give strongest interconnections. Should wireless connection between two devices weaken, the network will 'self-heal' and automatically re-route communications via alternate RICOCHET enabled devices, creating a mesh type network that provides a more robust and efficient wireless network.

When Detective+ goes into alarm, the signal will be sent to other units alerting the user to gas being present in the area. If the signal is weak due to heavy metal work being present the Detective Wireless can be used as a repeater to boost the signal between units. In a confined space the unit can use up to 20 metres of cable to position the unit in a location that will increase signal.

Versatile and user friendly

• Infrared sensors available - allows sampling of highly flammable gas levels and carbon dioxide. They are also unaffected by poisoning and have a very fast response time.
• Built-in pump option - provides sampling versatility
• Built-in display - provides clear information and allows identification of gas hazard

Rugged, tripod design

• Raised sensor apertures - prevents water ingress
• Folding leg options - allows stacking for easier storage and transportation
• IP65 specifications - for use in challenging environments
• Triple leg design - Increases unit physical visibility and is the perfect height to allow 360 gas inlet

Loud and clear alarms

• 25 Detective NET units or 12 Detective+ with cables can be networked together forming effective perimeter defense - Units on the network can be placed up to 100m from each other and if one alarms, all units on the network alarm.
• Intelligent and flexible units sending an alarm flash faster - provides guarantee to the use that the unit is functioning properly and they are protected
• Audible and visible confidence blip
• Vivid red LED clusters for visual alarm
• Multiple beacons - ensures 360° visibility

1450-405-DS404-3X 3 Unit DS405 Docking Station System by GfG

Easy operation

The operation of the DS404 docking station couldn't be any easier. Simply put the G450 or the G460 in the dock and the system will take over from there. The DS404 automatically performs a full functional test including fresh air calibration, bump test, extensive sensor tests, alarm tests and optionally performs an automatic AutoCal® calibration.

Extensive diagnostics

The DS404 is designed to go beyond the traditional basic docking station tests and includes sensor diagnostics tests such as T50 and T90. After all, what good is a sensor that can respond to gas when it takes too long to get there? With the DS404 you can have confidence with this added level of safety.

Automatic charging

After all tests have been completed the DS404 will automatically start the charging process of the detector or you may remove and begin using it. In case the detectors battery condition is insufficient to complete a test the DS404 will charge the instrument before performing the test.

Record Keeping

A good instrument gas detection maintenance program is not complete without equally good records keeping. Whether you choose to download or maintain the records on a PC or network or your preference is to leave it to the docking station, the DS404 is the right choice.

The DS404 can retain as many as 2 million complete diagnostics in memory with maximum memory installed. That is over 50 years of data even if testing 100 detectors every single day!

Reduced cost of ownership

The DS404 is designed to reduce the cost of ownership every step of the way. The built in pump has variable flow control to reduce the amount of gas consumed during the test. The DS404 is even smart enough take advantage of the gas remaining in the tubing after the previous test was completed.

PC communication

The DS404 comes complete with USB interface cable and download software. The SD card may also be downloaded using a standard SD card reader.

Maintenance certificates

quickly print official calibration or bump test certificates. Simply download the records from the DS404 and start the "Certificate Generator" it takes only seconds!

Features

• Four test gas ports
• Fully automatic functional bump test and calibration
• Automatic test of alarms
• Automatic charging
• Automatic record keeping
• Simple pass / fail indication
• Cascade multiple docking stations
• Saves last calibration and bump test records in detector for easy retrieval of maintenance record in the field
• No computer necessary
• Up to 2,000,000 records in memory
• Saves times, gas and efforts for lower cost of ownership
• Print official calibration certificates

Includes

• Four Gas Inlets
• Double Cradle
• Base Plate
• Unit-to-unit Power Adapters
• Ethernet Cables
• Standard Accessories

1450-921 G400 Motorized Smart Pump Alkaline by GfG

Optimized Alarm System

The new G400 MP-2 pump continuously communicates with the G450/G460 gas detector. This interaction allows fault indication via the detector display. Alarms such as low battery, blocked sampling line or interrupted power fault are shown on the display and activate a visual and audible alarm on the monitor.

Various Applications

Gas samples can be taken from a distance of up 100 meters (over 300 feet) at a typical draw rate of 0.5 liters per minute.

Superior Flexibility

The G400 MP-2 is the only detachable pump on the market today which will allow for operation in both diffusion mode and remote sample-draw mode. Simply slide the shutter to turn the pump on or off. When the pump is on, the shutter covers the diffusion inlets and exposes them when the pump is switched off.

The G400 MP-2 features a high efficiency redundant filter system in addition to a standard external probe with dust and hydrophobic filters.

Independent Power Supply

The G400 MP-2 is operated by its own power supply, independent of the gas detector. The power supply of the pump allows for up to 10 hours of continuous operation.

Features

• Optimized alarm system: Visual alarm via the G450/G460 display and alarm LEDs, Audible alarm via the G450/G460, Vibration alarm via the G450/G460
• Allows monitor to be used in either pump or diffusion mode
• Independent power supply (does not reduce instrument battery capacity)
• 300 feet (100 meter) remote sampling capability

Includes

• 10' of Tubing
• Probe with Filters

H-010-3006-000 Hand Pump Accessory Kit by Honeywell Analytics

Kit Includes

• 3 Rubber inlets
• Filters
• 2 Gaskets
• Lubricant

1450-402-3X 3 Unit DS402 Docking Station System by GfG

Easy operation

The operation of the DS400 docking station couldn't be any easier. Simply put the G450 or the G460 in the dock and the system will take over from there. The DS400 automatically performs a full functional test including fresh air calibration, bump test, extensive sensor tests, alarm tests and optionally performs an automatic AutoCal® calibration.

Extensive diagnostics

The DS400 is designed to go beyond the traditional basic docking station tests and includes sensor diagnostics tests such as T50 and T90. After all, what good is a sensor that can respond to gas when it takes too long to get there? With the DS400 you can have confidence with this added level of safety.

Automatic charging

After all tests have been completed the DS400 will automatically start the charging process of the detector or you may remove and begin using it. In case the detectors battery condition is insufficient to complete a test the DS400 will charge the instrument before performing the test.

Record Keeping

A good instrument gas detection maintenance program is not complete without equally good records keeping. Whether you choose to download or maintain the records on a PC or network or your preference is to leave it to the docking station, the DS400 is the right choice.

The DS400 can retain as many as 2 million complete diagnostics in memory with maximum memory installed. That is over 50 years of data even if testing 100 detectors every single day!

Reduced cost of ownership

The DS400 is designed to reduce the cost of ownership every step of the way. The built in pump has variable flow control to reduce the amount of gas consumed during the test. The DS400 is even smart enough take advantage of the gas remaining in the tubing after the previous test was completed.

PC communication

The DS400 comes complete with USB interface cable and download software. The SD card may also be downloaded using a standard SD card reader.

Maintenance certificates

The DS400 software includes a module to quickly print official calibration or bump test certificates. Simply download the records from the DS400 and start the "Certificate Generator" it takes only seconds!

Features

• Fully automatic functional bump test and calibration
• Automatic test of alarms
• Automatic charging
• Automatic record keeping
• Simple pass / fail indication
• Saves last calibration and bump test records in detector for easy retrieval of maintenance record in the field
• No computer necessary
• Up to 2,000,000 records in memory
• Cascade multiple docking stations
• Saves times, gas and efforts for lower cost of ownership
• Print official calibration certificates

Features

• Single gas inlet
• Double cradle
• Base plate
• Unit-to-unit power adapters
• Ethernet cables
• Standard accessories

MicroDock II Automatic Test and Calibration Station

The MicroDock II Test/Calibration Docking System is a cost-effective way to manage calibration, bump testing and datalogging of Honeywell Analytics X5 and XD portable gas detectors.

The MicroDock II packs advanced technology within a compact design to offer the industry s foremost automatic calibration, testing and data management system for portable gas detection equipment. Compatible with the Honeywell Analytics XD and X5 portable gas detectors, the MicroDock II expands up to 10 docking modules (including up to 6 charging units).

Fully portable, lightweight and self-contained, the MicroDock II requires no computer. Instrument records are stored for easy retrieval in the MicroDock II and each individual gas detector. Each MicroDock II system can be connected to a LAN.

Cost and time requirements for routine maintenance are reduced through the MicroDock II s sophisticated automatic calibration and test procedures.

The MicroDock II System includes Honeywell s Fleet Manager software, which consolidates MicroDock II s information into a central database, taking the work out of data analysis and management. This software tool enables users to:

• Create reports automatically
• Sort, format and export data
• View history
• Archive easily
• Customize with user-definable fields

User-friendly, flexible and expandable, the MicroDock II provides the ultimate solution for managing Honeywell Analytics high-performance XD and X5 portable gas detectors.

• Test, pass and fail led indicators
• Large, alphanumeric status lcd
• Fully automatic Hands Free test and calibration
• Built-in pumped inlets for gas delivery
• Easy expansion for multiple modules

Automatic Operation

• Automatic hands-free calibration and functional bump test
• Automatically checks performance of audible and visual alarms
• Simplified record keeping stores and updates calibration data
• Low Maintenance

Easy to Use

• No computer required
• Entirely self-contained
• Lightweight and mobile

Flexible & Expandable Applications

• Operates via line power or set of four C-cell batteries
• Additional self-contained docking modules added to system via simple, plug-in connections no external pressure transducers or gas lines necessary
• Minimized cost of ownership

Networking Support

• Multiple MicroDock II systems can be connected via a LAN
• Multi-language support in English, French, German, Spanish and Portuguese