Carbon Monoxide 1000

2811-428-003 EC 28 Gas Transmitter with Carbon Monoxide (CO) Sensor, 0 - 1,000 ppm Range, Display / Alarm by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG's proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds - just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm - Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG's GMA controller.

The EC 28 DA provides additional bright alarm LEDs and a buzzer - avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor - sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

17 Liter 1000 PPM Carbon Monoxide, 2.0% Oxygen Calibration Gas, Nitrogen

Part Number: 17L-327

17 Liter Carbon Monoxide Calibration Gas, 1000 PPM, Nitrogen

Part Number: 17L-49-1000

2813-428-002 EC 28i Intrinsically Safe Transmitter with Carbon Monoxide (CO) Sensor, 1 ppm Resolution, 0 - 1,000 ppm Range, Display by GfG

Wherever hazards are expected, the EC 28 transmitter and GfG's proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified Ex-proof design, and bright alarm LEDs provide the highest safety in hazardous areas. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds - just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the RC2 remote control (one-person calibration).

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Increased safety design to reduce installation cost in potentially hazardous locations
• Non-intrusive AutoCal® calbiration adjustment
• Uses electrochemical detection principle
• Output signal: 4-20 mA
• Intrinsically safe (i) EX-Proof
• Available in two configurations: Blind (no display); Display
• Barriers are required
• EX- conduit is not required

103 Liter 50 PPM Carbon Monoxide, 1000 PPM Carbon Dioxide Calibration Gas, Nitrogen

Part Number: 103L-389N

17 Liter 35 PPM Carbon Monoxide, 1000 PPM Carbon Dioxide Calibration Gas, Air

Part Number: 17L-320

17 Liter 50 PPM Carbon Monoxide, 1000 PPM Carbon Dioxide Calibration Gas, Air

Part Number: 17L-389

10 Liter 50 PPM Carbon Monoxide, 1000 PPM Carbon Dioxide Calibration Gas, Air

Part Number: 10L-389

Carbon Monoxide (CO-H) Reduced H2 Sensitivity, 0 - 1,000 ppm, Replacement Sensor with 3-Year Warranty NDIR (Infrared)

Carbon Monoxide (CO), 0 - 1,000 ppm, Replacement Sensor with 3-Year Sensor Warranty

17 Liter 35 PPM Carbon Monoxide, 1000 PPM Carbon Dioxide Calibration Gas, Air

Part Number: 17L-389-35

Carbon Monoxide (CO) Replacement Sensor, 1 ppm Resolution, 0 - 1,000 ppm Range

17 Liter 25 PPM Carbon Monoxide, 1000 PPM Carbon Dioxide Calibration Gas, Air

Part Number: 17L-380

10 Liter Carbon Monoxide Calibration Gas, 1000 PPM, Nitrogen

Part Number: 10L-49-1000

1418-107K Micro IV Value Kit with 3-Years Sensor Warranty, Carbon Monoxide (CO), 0 - 1000 ppm by GfG

Durable, compact design

The Micro IV is compact, robust and very easy to use. It is designed to be used in the harshest environments. The Micro IV includes a set of rubber boots to withstand hard knocks and drops.

Widest Range of sensors

Micro IV detectors are available for use with a wide range of long-lasting, interchangeable smart-sensors for the detection of O₂, H₂S, CO, NH₃, SO₂, Cl₂, ClO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂ and more.

Easy Operation

The Micro IV keeps gas detection simple. Most day-to-day functions are controlled with a single button, and calibration is fully automatic. Simply select the calibration mode from the keypad, attach the adapter and flow gas to the sensor. The GfG Autocal® feature automatically makes the adjustments and updates the information in the instrument s on-board memory.

Up to six months of battery life

The Micro IV delivers up to 3,000 hours of continuous operation from a single off the shelf AA alkaline battery. Battery replacement, when needed, can be completed in less than 30 seconds and requires no tools.

Clip-on attachment

The Micro IV comes with a heavy duty alligator clip that allows the detector to be conveniently clipped on to clothing and if so desired near the breathing zone.

Optional motorized pump

The Micro IV is available with an optional motorized pump to allow sampling from a remote location. The motorized pump may also be used in extraordinary harsh conditions, such as extreme heat, where it may be desirable to protect the instrument under protective clothing; using a tube the pump can draw air samples from the breathing zone.

Large graphic display

The Micro IV detector features a large backlit easy-to-read graphic display that provides a continuous readout for the sensor installed. By pressing a single button additional information such as Peak, STEL and TWA readings my be displayed.

Audible, vibrating and visual alarms

The Micro IV detector features a loud alarm (95db at 12 inches), a built-in vibrating alarm and a bright multi-directional visual LED alarm light.

Lifetime warranty

The Micro IV carries a lifetime warranty on non-consumable components and two or more years of warranty on most sensors. Select sensors such as O2, H2S, and CO carry a full three year warranty against failure.

DS220 docking station

The Micro IV is available with a six position fully automatic docking station. The docking station makes bump test and calibration even easier and all maintenance records are stored automatically. The docking station fully test sensor response, alarms and other functionality.

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Value Kit Configuration

• All standard accessories: Micro IV detector, Specified Sensor, Alkaline Battery, Rubber Boot, Manual
• Calibration Adapter
• Calibration Gas
• Fixed Flow Regulator
• ABS Carrying Case

Carbon Monoxide (CO) Replacement Sensor, 1 ppm Resolution, 0 - 1,000 ppm Range

103 Liter 25 PPM Carbon Monoxide, 1000 PPM Carbon Dioxide Calibration Gas, Air

Part Number: 103L-380

17 Liter 100 PPM Carbon Monoxide, 1000 PPM Carbon Dioxide Calibration Gas, Nitrogen

Part Number: 17L-375

2811-428-001 EC 28 Gas Transmitter with Carbon Monoxide (CO) Sensor, 0 - 1,000 ppm Range, No Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG's proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds - just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm - Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG's GMA controller.

The EC 28 DA provides additional bright alarm LEDs and a buzzer - avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor - sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

103 Liter 35 PPM Carbon Monoxide, 1000 PPM Carbon Dioxide Calibration Gas, Air

Part Number: 103L-320

Savannah Specialty 100 ppm Carbon Monoxide / 0.025 (50% LEL) Methane / 0.19 Oxygen / Nitrogen 34 Liter Cylinder

10 Liter 50 PPM Carbon Monoxide, 1000 PPM Carbon Dioxide Calibration Gas, Nitrogen

Part Number: 10L-389N

10 Liter 100 PPM Carbon Monoxide, 1000 PPM Carbon Dioxide Calibration Gas, Nitrogen

Part Number: 10L-375

103 Liter 35 PPM Carbon Monoxide, 1000 PPM Carbon Dioxide Calibration Gas, Air

Part Number: 103L-389-35