Test Products International

716A740 716 Flue Gas Analyzer Kit by Test Products International

Features

• Built-in differential manometer with 0.001 H2O resolution
• Calculates combustion efficiency
• Data Logging with time and date stamp
• Will not shut off if 15 ppm CO is present for increased safety
• Communicate to a PC via the USB interface
• Optional A740 IR printer available for hard copies of test results
• Built-in differential thermometer
• Push on fittings for fast and easy use
• Optional Bluetooth interface

A740 Features

• Easy to use
• Battery operated
• Self test facility
• Adjustable contrast
• Manual paper feed
• Maximum transmitting distance 16"(45cm)

Includes

• 716 Flue Gas Analyzer
• A740 IR Printer

SP250B Switchable Passive Oscilloscope Probe, 250MHz, 1.2M Cable Length by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

712A740C1 712 Combustion Efficiency Analyzer Kit by Test Products International

712 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature
• Dual input pressure with 0.001 inches water resolution for high efficiency & oil
• Optional A767 adapter for PC interface

A740 Features

• Easy to use
• Battery operated
• Self test facility
• Adjustable contrast
• Manual paper feed
• Maximum transmitting distance 16"(45cm)

A773

Use the A773 when working on oil fired appliances to extend the life of your sensors by eliminating acid gas exposure to your analyzer

58-1200-1M RG58/U, BNC Male to BNC Male, 100 Feet by Test Products International

50 Ohm, 75 Ohm, 93 Ohm. TPI BNC to BNC coax cable assemblies include: RG58/U (molded and assembled), RG59/U and RG62/U.

Features

• UL Listed Cable: Ensures quality and consistency in the cable construction.
• Boot is molded to cable connector for added strength: Limits the amount of bending the cable is exposed to at the connector to prevent cable breakage.
• Gold center pins: Ensures that there is a high quality connection maintaining the best return loss in high definition applications.
• Machined Brass Connectors: Unlike die-cast connectors, machined brass connectors have more precise tolerances, strength and positive mating meaning low signal loss for precise video and data applications.
• Boot is molded to cable connector for added strength
• 95% shielding
• 80°F temperature rating
• Multiple lengths up to 100 feet
• Individually bagged

712C7 712 Combustion Efficiency Analyzer Kit by Test Products International

712 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature
• Dual input pressure with 0.001 inches water resolution for high efficiency & oil
• Optional A767 adapter for PC interface

270 Features:

• Measure motor in-rush current and run current
• Measure temperature differential with relative mode
• Non-contact voltage feature can be used to immediately see if power is being supplied to the 24VAC control circuit of thermostats
• Frequency, Min/Max/Record, Data Hold and Peak Hold
• Up to 40,000 Microfarads to test run and start capacitors
• 4,000 count display with 41 segment analog bargraph
• Auto & Manual Ranging
• Low Battery Indicator
• Over Range Indication ("OL")
• Hi Voltage Indicator (>30V AC/DC)
• Auto Power Off after 30 minutes
• Separate Battery/Fuse Compartment
• Low Ohm Range (400V)
• Amps AC Resolution: 0.01A
• VDC/VAC Resolution: 0.1mV
• DC μA measurement (0.01 μA resolution)
• Temperature measurement with 0.1° resolution

A740 Features

• Easy to use
• Battery operated
• Self test facility
• Adjustable contrast
• Manual paper feed
• Maximum transmitting distance 16"(45cm)

Includes

• 712 Combustion Efficiency Analyzer
• 270 Clamp-On Tester with Digital Multimetervisit
• A740 IR Printer

126 Compact Autoranging DMM with 0.3% DCV Basic Accuracy and 400mA AC/DC Range by Test Products International

The 126 is a hand-held autoranging DMM. The 126 measures ACV, DCV, ACA, DCA, Resistance, Diodes and Continuity.

Features:

• REC: Records Min/Max readings during specified measurement intervals.
• AC/DC:Toggles between AC/DC volts and Amps.
• Data Hold: Holds the reading on the display for easy viewing.
• Auto Off: Preserves battery life. LCD shows oFF when in this mode. Automatically powers down after 30 minutes of inactivity.
• Agency Approval: Meets CE and IEC 1010 requirements.
• 4,000 count display
• 0.3% DCV basic accuracy
• 0 to 600 ACV; max resolution 1mV
• 0 to 40MΩ; max resolution 0.1Ω
• Audible continuity
• 0 to 400 mA amps AC/DC; max resolution 0.01mA
• Autoranging
• Min/Max
• Data Hold
• cULus 61010-1
• CAT II - 1000V, CAT III - 600V

Applications:

• Thermocouples in furnaces or gas applications
• Thermocouples in furnaces of gas applications. DC Controlled circuits
• Heat anticipator current in thermostats
• Line voltage
• Control circuit voltage
• Flame safeguard control current
• Heating element resistance (continuity)
• Compressor winding resistance
• Contactor and relay coil resistance
• Continuity of wiring
• Temperature with optional temperature adapter

The 126 comes complete with the following accessories:

• 126 Instrument
• Rubber Boot
• Test Lead Set
• Battery
• Instruction Manual

SP300B Switchable Passive Oscilloscope Probe, 300MHz, 1.2M Cable Length by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial