Test Products International

395 Handheld Refractometer by Test Products International

TPI Model 395 Handheld Refractometer. Use the 395 to determine the freezing point of fluids including those used in hydronic heating systems.

The 395 Handheld Refractometer is designed to give an accurate reading regarding the freezing point of fluids used in hydronic heating systems. It is quick and easy to use. Place a drop of fluid on the prism, close the plastic lid, and look through the eye piece: where the blue and white colors meet indicates the freezing point of the coolants or the state of change for batteries.

Features

• Test propylene glycol, ethylene glycol and battery fluids
• Does not degrade like litmus paper; allows for more accurate readings
• Cushioned eye piece for easy viewing
• Smooth focus adjustment for reliable repeat testing

Applications

• HVACR: Radiant Heat Line Fluids For walkways, garages, closed loop systems, and in-floor systems
• Automotive: Engine coolants
• Automotive: Battery fluid condition
• Automotive: Recreational vehicles
• Plumbing: Battery condition of sump pump battery back up systems

306XC Calibratable Low Cost Pocket Digital Thermometer (Centigrade Version of the 306) with A306 by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Field calibrateable to ±2°F
• Easy-to-read LCD
• Data Hold for hard to reach areas
• Penetration tip
• Auto off
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

351/F1 Thermistor Thermometer with FX11B Probe by Test Products International

TPI contact temperature testers are accurate, reliable, and built to last. Models 341K, 343 and 367D can be auto field calibrated to system accuracy (tester plus probe) of ± 1°F in less than 10 seconds in ice water.

Auto Field Calibration Perform ice bath calibration to achieve ±1°F system accuracy within the 30°F to 120°F temperature range. Calibration is an easy two-step process performed with instrument keypad, no additional tools needed.

Features:

• Auto Off
• Includes A304
• Protective rubber boot

Includes:

• FX11B probe
• A304 protective boot
• A255 soft pouch

SAIT200 Analog Insulation Resistance Tester (IRT) by Test Products International

TPI Insulation Resistance Testers are ideal for preventative maintenance and performing resistance tests. All TPI Insulation Resistance Testers include A085 UL listed silicone test lead set with screw on alligator clips and A073 test lead set with large alligator clips.

Features

• Easy to use
• Push button or locking operation
• Automatic discharge
• Built-in battery test
• Test Voltages: 250V/500V/1,000V
• Insulation Resistance: 100MΩ/200MΩ/400MΩ
• Continuity: 2Ω/20Ω
• Includes A085 UL listed silicone test lead set with screw on alligator clips and A073 test lead set with large alligator clips

Applications

• Cables
• Compressors
• Controls
• Distribution Transformers
• Generators
• Instruments
• Motors
• Windings
• Switchgear

Markets

• Electrical Power Generation
• Heavy Industry
• HVACR
• Mining
• Motor Repair Shops
• Natural Gas Transmission
• Oil Production
• Oil Pipelines
• Railroads
• Refining
• Steel Manufacturing
• Gathering facilities, compressor stations and pipelines

708C10 708 Combustion Efficiency Analyzer Kit by Test Products International

708 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature

Includes

• 621 Dual Differential Input Manometer
• A740 IR Printer
• Two GK13M K-Type General Purpose Beaded Tip Air Probe
• Two 605 Single Input Digital Vacuum Gauge
• Two A603 Brass Fitting

275 Clamp-On Tester with True RMS Digital Multimeter and 11,000 Count Display by Test Products International

Clamp-On Tester with True RMS Digital Multimeter & 11,000 Count Display. The new TPI 275 with slim jaw and body is ideal for cramped work areas and crowded electrical panels.

The slim design 275 is a hand-held, autoranging clamp-on DMM. Extra large numerals, min/max, capacitance, DC microamps and duty cycle are just a few of the features of the 275. An affordable choice, the 275 offers measurements in all basic electrical functions with additional advanced features like non-contact voltage.

Features:

• True RMS
• 11,000 count display
• Up to 400 amps AC/DC
• Auto & Manual Ranging
• Data Hold
• Low Battery Indicator
• Over Range Indication ("OL")
• Peak Hold
• Min/Max
• Relative Mode
• Hi Voltage Indicator(>30V AC/DC)
• Non-contact voltage detection
• Auto Power Off after 30 minutes
• Separate Battery Compartment
• Low Ohm Range (110Ω)
• Amps AC Resolution: 0.01A
• VDC/VAC Resolution: 0.01mV
• DCiA measurement (0.01μA resolution)
• Temperature measurement

Applications:

• Measure DC amperage of motor drive units
• Measure flame safety control current
• Test run and start capacitors and motors
• Measure motor run current and capture peak motor start up amperage
• Measure heat anticipator current
• Determine thermocouple voltage
• Test line and control voltages
• Measure heating element resistance
• Measure air temperature in ducts
• Test for the presence of voltage in circuits without contacting the circuit
• Measure temperature differential using relative mode

The 275 comes complete with the following accessories:

• Carrying Pouch
• Test Lead Set
• Temperature Probe
• Instruction Manual
• Battery & Fuse

753A Refrigerant Leak Detector by Test Products International

The 750a features 400 hour sensor life under normal use; a spare sensor is included with each instrument for a total of 800 hours of continuous use and can detect leaks as small as 0.1 ounces per year (R134a / R22).

Whether testing for leaks in air conditioning, refrigeration, or automotive AC, the versatile 700 series spans the diverse needs of technicians, refrigeration engineers, and maintenance personnel around the globe. From freezer coils to heat pumps, experience fast, reliable results that save you both time and money.

The TPI 750a is a state-of-the-art refrigerant leak detector capable of detecting all halogen based gases. The internal diaphragm pump and unique sensor design provide fast and reliable gas sensing. Selectable sensitivity combined with an adjustable tick rate will allow any service professional to pinpoint those tough to find leaks even in contaminated environments.

Sensor life can be extended by fitting a 1/2" long piece of vinyl tubing onto the sensor tip. This tubing helps prevent foreign material from getting into the sensor during tests; clean or replace the tube regularly.

Even though TPI refrigerant leak detector sensors are very durable and can last up to 400 hours, sensor life can be aided by press fitting a 1/2" long piece of vinyl tubing onto the sensor tip. This tubing helps prevent foreign material from getting into the sensor during tests. Clean or replace the tube regularly.

Features

• Detects all existing refrigerants and blends including 404A, PURON 410A and *R-507 (AZ50)
• 400 hour individual sensor life; a spare sensor is included with each instrument for a total of 800 hours of continuous sensor use.
• Fast response; Begin testing immediately after power on
• 0.1 ounce per year sensitivity
• Pump driven for increased sensitivity with blended refrigerants
• Pinpoint small leaks easily by elimination of background concentration with fully adjustable tic rate
• Visual indicators for power, tic rate and battery replacement
• Optional earphone attachment

Applications

• Check for leaks in refrigeration systems
• Test for leaks in air conditioning systems and cooling units
• Find leaks in automotive air conditioning systems

Standard Accessories

• Sensor: A721
• Instruction Manual: 753a Instruction Manual
• Soft Case with strap (A755)

Optional Accessories

• Earphone A710
• Test vial A713

SDIT30 Digital Insulation Resistance Tester (IRT) by Test Products International

TPI Insulation Resistance Testers are ideal for preventative maintenance and performing resistance tests. All TPI Insulation Resistance Testers include A085 UL listed silicone test lead set with screw on alligator clips and A073 test lead set with large alligator clips.

Features

• Easy to use
• Push button or locking operation
• Automatic discharge
• Built-in battery test
• Test Voltages: 250V/500V/1,000V
• Insulation Resistance: 2,000MMΩ/2,000MΩ/2,000MΩ
• Continuity: 200Ω
• Includes A085 UL listed silicone test lead set with screw on alligator clips and A073 test lead set with large alligator clips

Applications

• Cables
• Compressors
• Controls
• Distribution Transformers
• Generators
• Instruments
• Motors
• Windings
• Switchgear

Markets

• Electrical Power Generation
• Heavy Industry
• HVACR
• Mining
• Motor Repair Shops
• Natural Gas Transmission
• Oil Production
• Oil Pipelines
• Railroads
• Refining
• Steel Manufacturing
• Gathering facilities, compressor stations and pipelines