Test Products International

SP200B Switchable Passive Oscilloscope Probe, 200MHz, 1.2M Cable Length by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

153 Autoranging DMM with Boot, Test Leads, Battery and Manual by Test Products International

The 153 is a hand-held autoranging DMM. The 153 measures ACV, DCV, ACA, DCA, Resistance, Diodes and Continuity.

Features:

• Agency Approval: Meets CE and IEC 1010 requirements. UL Listed to U.S. and Canadian Safety Standards.
• Sleep: Instrument automatically powers down after 30 minutes of inactivity, however, it will continue acquiring data in its various modes. Pressing any push button or turning the rotarty switch returns the 153 back to normal.
• Range: Allows you to either manual range or use auto range to select the appropriate range.
• Auto Off: Preserves battery life. LCD shows oFF when in this mode.
• Record: Records Min/Max values.M
• Data Hold: Holds the reading on the display for easy viewing.
• 0.3% DCV basic accuracy
• 0 to 750 ACV; max resolution 1mV
• 0 to 1,000 DCV; max resolution 0.1mV
• 0 to 40MΩ; max resolution 0.1Ω
• AC/DC amps to 10; max resolution 0.1uA
• Min/Max
• cULus 61010-1
• CAT II - 1000V, CAT III - 600V

Applications:

• Thermocouples in furnaces or gas applications
• Heat anticipator current in thermostats
• Line voltage
• Voltage of direct drive DC motors
• Control circuit voltage
• Motor run and start capacitors
• Flame safeguard control current
• Heating element resistance (continuity)
• Compressor winding resistance
• Contactor and relay coil resistance
• Continuity of wiring
• Continuity of circuit breakers
• Temperature with optional temperature adapter
• Bar graph to indicate rapid fluctuations in measurements

The 153 comes complete with the following accessories:

• Rubber Boot
• Test Lead Set
• Battery
• Instruction Manual

A296 AC/DC Amp Current Probe Adapter by Test Products International

Most TPI brand and any competitor DMM, clamp-on or oscilloscope having the capability of measuring up to 2000mV AC/DC (2V AC/DC), 10M Ohm input impedance, and equipped with industry standard spaced input jacks 19mm on center

TPI-5010 Universal Adapter Cable Kit by Test Products International

For use with TPI-3000A and TPI-5000A adapter kits

• Provides the functionality of an entire set of cables
• Creates the cable of your choice using the universal cable and any combination of connectors from the kits noted above
• No soldering, no crimping - cable may be used over and over in different combinations
• Soft insulation makes cable flexible and easy to handle
• Kit includes 6ea. 48" universal cables and wall rack

317C Calibratable Pocket Digital Thermometer with Air Tip by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Air tip
• Field calibrateable to ±2°F
• Rugged and waterproof (IP63)
• 3.1mm stem for "Pete's" plug
• Auto off
• -Magnetic clip perfect for air duct applications
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

270 Clamp-On Tester with Digital Multimetervisit by Test Products International

Perfect for tight, narrow, spaces. The new TPI 270 with slim jaw and body is ideal for cramped work areas and crowded electrical panels.

The slim design 270 is a hand-held, autoranging clamp-on DMM. Extra large numerals, min/max, capacitance, DC microamps and duty cycle are just a few of the features of the 270. An affordable choice, the 270 offers measurements in all basic electrical functions with additional advanced features like non-contact voltage.

Features:

• Measure motor in-rush current and run current
• Measure temperature differential with relative mode
• Non-contact voltage feature can be used to immediately see if power is being supplied to the 24VAC control circuit of thermostats
• Frequency, Min/Max/Record, Data Hold and Peak Hold
• Up to 40,000 Microfarads to test run and start capacitors
• 4,000 count display with 41 segment analog bargraph
• Auto & Manual Ranging
• Low Battery Indicator
• Over Range Indication ("OL")
• Hi Voltage Indicator (>30V AC/DC)
• Auto Power Off after 30 minutes
• Separate Battery/Fuse Compartment
• Low Ohm Range (400V)
• Amps AC Resolution: 0.01A
• VDC/VAC Resolution: 0.1mV
• DC μA measurement (0.01 μA resolution)
• Temperature measurement with 0.1° resolution

Applications:

• Measure flame safety control current
• Test run and start capacitors and motors
• Measure motor run current and capture peak motor start up amperage
• Measure heat anticipator current
• Determine thermocouple voltage
• Test line and control voltages
• Measure heating element resistance
• Measure air temperature in ducts
• Test for the presence of voltage in circuits without contacting the circuit
• Measure temperature differential using relative mode

The 270 comes complete with the following accessories:

• Carrying Pouch
• Test Lead Set
• Temperature Probe
• Instruction Manual
• Battery & Fuse

F6-12W 12 Foot White F Male to F Male by Test Products International

F-series coax cable assemblies with screw-on ends for broadband applications, including video and cable television.

Features

• UL Listed Cable: Ensures quality and consistency in the cable construction.
• RG-6: Cable type that is standard in the video and cable TV industry
• Molded Ends: Limits the amount of bending the cable is exposed to at the connector to prevent cable breakage.
• Screw-on F-Type Connectors: Ensure positive connection thus eliminating shadows in the picture.
• Multiple lengths up to 100 feet
• Available in black or white
• Individually bagged

F6-10B 10 Foot Black F Male to F Male by Test Products International

F-series coax cable assemblies with screw-on ends for broadband applications, including video and cable television.

Features

• UL Listed Cable: Ensures quality and consistency in the cable construction.
• RG-6: Cable type that is standard in the video and cable TV industry
• Molded Ends: Limits the amount of bending the cable is exposed to at the connector to prevent cable breakage.
• Screw-on F-Type Connectors: Ensure positive connection thus eliminating shadows in the picture.
• Multiple lengths up to 100 feet
• Available in black or white
• Individually bagged

133 Manual Ranging DMM, with Boot, Test Leads, Battery and Manual by Test Products International

The 133 is a hand-held autoranging DMM. It features extra large numerals on the LCD, and Data Hold for all functions and ranges. The 133 is an affordable choice offering measurements in all of the basic electrical functions.

Features:

• Safety: Meets CE and IEC 1010 requirements. UL Listed to U.S. and Canadian Safety Standards.
• Large LCD:Easy to read at all angles and the majority of lighting levels. 4000 Count.
• Rubber Boot: Added protection when the instrument is dropped. (135NB does not include boot.)
• Multi-function: Measure all electrical characteristics with one meter.
• 0.5% DCV basic accuracy
• 0 to 750 ACV; max resolution 1mV
• 0 to 1,000 DCV; max resolution 0.1mV
• 0 to 20MΩ; max resolution 0.1Ω
• 0 to 10 amps AC/DC; 0.1uA resolution
• Data Hold
• cULus 61010-1
• CAT II - 1000V, CAT III - 600V

Applications:

• Thermocouples in furnaces and gas appliances
• Heat anticipator current in thermostats
• Line and control voltages
• Flame safety control current
• Heating element resistance
• Continuity of wiring
• Line current up to 10 amps
• Power supply current

The 133 comes complete with the following accessories:

• 133 Instrument
• Rubber Boot (133NB does not include boot)
• Test Lead Set
• Battery
• Instruction Manual

708C10 708 Combustion Efficiency Analyzer Kit by Test Products International

708 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature

Includes

• 621 Dual Differential Input Manometer
• A740 IR Printer
• Two GK13M K-Type General Purpose Beaded Tip Air Probe
• Two 605 Single Input Digital Vacuum Gauge
• Two A603 Brass Fitting