Test Products International

715 High CO Combustion Analyzer with Built-in Differential Thermometer, Differential Manometer, and NO Measurement & NOX Calculation by Test Products International

The carbon monoxide sensor used in TPI combustion efficiency analyzers feature an on-board filter capable of filtering NO (nitric oxide), NO₂ (nitrogen dioxide) and NOX (combination of NO and NO₂) to prevent cross sensitivity errors.

Use TPI analyzers to test flue gases in gas and oil fired equipment including high efficiency furnaces and condensing boilers. Measure CO, O₂, and stack temperature.

Determine combustion efficiency, CO₂, and CO air free. Some models include built-in differential manometer, combustible gas detection, PC communication, data logging, and can measure NO / NOX.

Use the optional A784 flow regulator to reduce the flow rate of the gas being sampled to measurable levels on high pressure systems such as gas compression engines. The A784 is included in the 715K3 kit.

Features

Using TPI analyzers to determine combustion efficiency at the time of equipment set up minimizes call backs and can be used to verify to the home owner the value of service work by showing the increase in equipment efficiency after work is performed. Efficiency calculation can also be used to generate business by demonstrating the need to improve the efficiency of equipment or to show the benefit of purchasing new equipment with higher efficiency.

Quick And Simple Set Up

All TPI analyzers feature quick and simple set up. Fast purge and the ability to perform fuel selection during start up enable tests to be performed quickly without requiring extra set-up time after initial startup. TPI analyzers also use the last selected fuel as the default setting. This feature prevents the need toperform fuel selection every time the analyzer is turned on.

• Measure up to 9.999% CO
• Built-in differential thermometer
• Measure NO (Nitric Oxide), Calculate NOx
• Store function to save up to 10 readings
• Calculates combustion efficiency
• Pump driven for fast response
• Push on fittings for fast and easy use
• Large easy to read backlit display
• Will not shut off if 15 ppm CO is present for increased safety
• Four selectable fuels: Natural Gas, LPG, Light Oil, Heavy Oil
• Optional A740 IR printer available for hard copies of test results

Applications

• Tune combustion engines
• Test CO levels in industrial boilers
• Measure NO and calculate NOX

708 Combustion Efficiency Analyzer with Flue Probe by Test Products International

The carbon monoxide sensor used in TPI combustion efficiency analyzers feature an on-board filter capable of filtering NO (nitric oxide), NO₂ (nitrogen dioxide) and NOX (combination of NO and NO₂) to prevent cross sensitivity errors.

Use TPI analyzers to test flue gases in gas and oil fired equipment including high efficiency furnaces and condensing boilers. Measure CO, O₂, and stack temperature.

Determine combustion efficiency, CO₂, and CO air free. Some models include built-in differential manometer, combustible gas detection, PC communication, data logging, and can measure NO / NOX.

Features

Using TPI analyzers to determine combustion efficiency at the time of equipment set up minimizes call backs and can be used to verify to the home owner the value of service work by showing the increase in equipment efficiency after work is performed. Efficiency calculation can also be used to generate business by demonstrating the need to improve the efficiency of equipment or to show the benefit of purchasing new equipment with higher efficiency.

Quick And Simple Set Up

All TPI analyzers feature quick and simple set up. Fast purge and the ability to perform fuel selectionduring start up enable tests to be performed quickly without requiring extra set-up time after initial startup. TPI analyzers also use the last selected fuel as the default setting. This feature prevents the need toperform fuel selection every time the analyzer is turned on.

• Measure CO, and temperature
• Calculate CO2, efficiency, excess air, and CO air free
• Pump driven for fast response
• Will not shut off if 15 ppm CO is present for increased safety
• Ten selectable fuels: Natural Gas, LPG, Light Oil, Heavy Oil, Bituminous Coal, Anthracite Coal, Coke, Butane, Wood, Bagasse
• Optional A740 IR printer available for hard copies of test results
• Built-in differential thermometer
• Store function to save up to 50 readings
• Large easy to read backlit display

Applications

• Tuning of residential and furnaces and domestic boilers
• Ambient and stack testing for CO
• CO safety measurements in and around combustion sources
• Temperature checking, including superheat and hydronic differential temperatures

709R Combustion Efficiency Analyzer with Differential Manometer by Test Products International

The carbon monoxide sensor used in TPI combustion efficiency analyzers feature an on-board filter capable of filtering NO (nitric oxide), NO₂ (nitrogen dioxide) and NOX (combination of NO and NO₂) to prevent cross sensitivity errors.

Use TPI analyzers to test flue gases in gas and oil fired equipment including high efficiency furnaces and condensing boilers. Measure CO, O₂, and stack temperature.

Determine combustion efficiency, CO₂, and CO air free. Built-in differential manometer, combustible gas detection, PC communication, data logging, and can measure NO / NOX.

Features

Using TPI analyzers to determine combustion efficiency at the time of equipment set up minimizes call backs and can be used to verify to the home owner the value of service work by showing the increase in equipment efficiency after work is performed. Efficiency calculation can also be used to generate business by demonstrating the need to improve the efficiency of equipment or to show the benefit of purchasing new equipment with higher efficiency.

Quick And Simple Set Up

All TPI analyzers feature quick and simple set up. Fast purge and the ability to perform fuel selection during start up enable tests to be performed quickly without requiring extra set-up time after initial startup. TPI analyzers also use the last selected fuel as the default setting. This feature prevents the need to perform fuel selection every time the analyzer is turned on.

• High resolution 0.001 in H20 differential manometer for high efficiency and oil equipment
• Measure CO, and temperature
• Calculate CO2, efficiency, excess air, and CO air free
• Pump driven for fast response
• Will not shut off if 15 ppm CO is present for increased safety
• Ten selectable fuels: Natural Gas, LPG, Light Oil, Heavy Oil, Bituminous Coal, Anthracite Coal, Coke, Butane, Wood, Bagasse
• Optional A740 IR printer available for hard copies of test results
• Built-in differential thermometer
• Store function to save up to 50 readings
• Large easy to read backlit display
• Rechargeable Ni-MH Battery with > 6 Hours battery life

Applications

• Tuning of residential and furnaces and domestic boilers
• Ambient and stack testing for CO
• CO safety measurements in and around combustion sources
• Temperature checking, including superheat and hydronic differential temperatures
• Dual input differential manometer

58-060-1A RG58/U, BNC Male to BNC Male, 60 inch by Test Products International

50 Ohm, 75 Ohm, 93 Ohm. TPI BNC to BNC coax cable assemblies include: RG58/U (molded and assembled), RG59/U and RG62/U.

Features

• UL Listed Cable: Ensures quality and consistency in the cable construction.
• Boot is molded to cable connector for added strength: Limits the amount of bending the cable is exposed to at the connector to prevent cable breakage.
• Gold center pins: Ensures that there is a high quality connection maintaining the best return loss in high definition applications.
• Machined Brass Connectors: Unlike die-cast connectors, machined brass connectors have more precise tolerances, strength and positive mating meaning low signal loss for precise video and data applications.
• Boot is molded to cable connector for added strength
• 95% shielding
• 80°F temperature rating
• Multiple lengths up to 100 feet
• Individually bagged

712 Deluxe Combustion Efficiency Analyzer with Optional PC Interface by Test Products International

The carbon monoxide sensor used in TPI combustion efficiency analyzers feature an on-board filter capable of filtering NO (nitric oxide), NO₂ (nitrogen dioxide) and NOX (combination of NO and NO₂) to prevent cross sensitivity errors.

Use TPI analyzers to test flue gases in gas and oil fired equipment including high efficiency furnaces and condensing boilers. Measure CO, O₂, and stack temperature.

Determine combustion efficiency, CO₂, and CO air free. Built-in differential manometer, combustible gas detection, PC communication, and data logging.

Features

Using TPI analyzers to determine combustion efficiency at the time of equipment set up minimizes call backs and can be used to verify to the home owner the value of service work by showing the increase in equipment efficiency after work is performed. Efficiency calculation can also be used to generate business by demonstrating the need to improve the efficiency of equipment or to show the benefit of purchasing new equipment with higher efficiency.

Quick And Simple Set Up

All TPI analyzers feature quick and simple set up. Fast purge and the ability to perform fuel selectionduring start up enable tests to be performed quickly without requiring extra set-up time after initial startup. TPI analyzers also use the last selected fuel as the default setting. This feature prevents the need toperform fuel selection every time the analyzer is turned on.

• High resolution 0.001 in H20 differential manometer for high efficiency and oil equipment
• Measure CO, and temperature
• Calculate CO2, efficiency, excess air, and CO air free
• Pump driven for fast response
• Will not shut off if 15 ppm CO is present for increased safety
• Ten selectable fuels: Natural Gas, LPG, Light Oil, Heavy Oil, Bituminous Coal, Anthracite Coal, Coke, Butane, Wood, Bagasse
• Optional A740 IR printer available for hard copies of test results
• Built-in differential thermometer
• Store function to save up to 50 readings
• Large easy to read backlit display
• Rechargeable Ni-MH Battery with > 6 Hours battery life
• Optional Bluetooth interface
• Checks combustibles in flue, optional PC interface

Applications

• Tuning of residential and furnaces and domestic boilers
• Ambient and stack testing for CO
• CO safety measurements in and around combustion sources
• Temperature checking, including superheat and hydronic differential temperatures
• Detecting gas leak in gas lines and around gas fueled appliances. Dual input differential manometer with 3 selectable units of measure: kPa, mBar,inH20

709 Combustion Efficiency Analyzer and Differential Manometer by Test Products International

The carbon monoxide sensor used in TPI combustion efficiency analyzers feature an on-board filter capable of filtering NO (nitric oxide), NO₂ (nitrogen dioxide) and NOX (combination of NO and NO₂) to prevent cross sensitivity errors.

Use TPI analyzers to test flue gases in gas and oil fired equipment including high efficiency furnaces and condensing boilers. Measure CO, O₂, and stack temperature.

Determine combustion efficiency, CO₂, and CO air free. Built-in differential manometer, combustible gas detection, PC communication, data logging, and can measure NO / NOX.

Features

Using TPI analyzers to determine combustion efficiency at the time of equipment set up minimizes call backs and can be used to verify to the home owner the value of service work by showing the increase in equipment efficiency after work is performed. Efficiency calculation can also be used to generate business by demonstrating the need to improve the efficiency of equipment or to show the benefit of purchasing new equipment with higher efficiency.

Quick And Simple Set Up

All TPI analyzers feature quick and simple set up. Fast purge and the ability to perform fuel selectionduring start up enable tests to be performed quickly without requiring extra set-up time after initial startup. TPI analyzers also use the last selected fuel as the default setting. This feature prevents the need toperform fuel selection every time the analyzer is turned on.

• High resolution 0.001 in H20 differential manometer for high efficiency and oil equipment
• Measure CO, and temperature
• Calculate CO2, efficiency, excess air, and CO air free
• Pump driven for fast response
• Will not shut off if 15 ppm CO is present for increased safety
• Ten selectable fuels: Natural Gas, LPG, Light Oil, Heavy Oil, Bituminous Coal, Anthracite Coal, Coke, Butane, Wood, Bagasse
• Optional A740 IR printer available for hard copies of test results
• Built-in differential thermometer
• Store function to save up to 50 readings
• Large easy to read backlit display

Applications

• Tuning of residential and furnaces and domestic boilers
• Ambient and stack testing for CO
• CO safety measurements in and around combustion sources
• Temperature checking, including superheat and hydronic differential temperatures
• Dual input differential manometer

326 Calibratable Water Resistant Digital Pocket Thermometer with Needle Tip by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Field calibrateable to ±2°F
• Easy-to-read LCD
• Data Hold for hard to reach areas
• Penetration tip
• Auto off
• 3.1 mm stem for fast response
• 4.9 inch stem for insertion in liquids and semi-solids
• IP Rating IP67
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

315C Calibratable Pocket Digital Thermometer with Magnets by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Auto field calibration to ± 2F
• Tapered stem (3.1 mm diameter) to fit into a Pete's Plug
• Reinforced, heavy-duty housing for strength
• Waterproof (IP63)
• Fits in your pocket
• -58°F to 300°F (-50°C to 150°C)
• Rugged design to withstand a 10 foot drop
• Magnetic clip perfect for air duct applications
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

707 Carbon Monoxide Analyzer by Test Products International

Use the 707 to measure CO levels in the flue and test ambient CO levels in home and office spaces. Hand held and easy to use.

Test flue gasses at home or office spaces for the presence and location of CO leaks. With a protective rubber boot, the new 707 fits comfortably in your hand and operates with the push of a button.

The TPI 707 Carbon Monoxide Analyzer is a state of the art, easy to use analyzer designed to display carbon monoxide levels in and around appliances and work / living spaces. The instrument is ruggedly constructed and comes with a 3 Year unit and 2 Year sensor Guarantee.

The TPI 707 combustion analyzer uses a state of the art electrochemical sensor. This sensor technology provides the longest lasting, most accurate and reliable means for performing tests. The sensor in your analyzer will need to be replaced periodically and calibration is recommended once every year. The 707 will remind you when calibration is due by flashing "CAL DUE Err" for three seconds at start up if the date of calibration is one year or older.

Electrochemical sensors by nature are always active. Therefore the time the analyzer is off and not being used must be taken into account when determining sensor life. The sensor in your analyzer is warranted for two years. This warranty does not cover a sensor damaged through misuse of the analyzer.

Features

• Clear and fast response with advance pump driven technology
• Peak Hold to capture peak CO reading
• Instrument recycles and will not shut off if 15ppm CO is present, increasing safety
• Store Button allows you to save up to eight readings and then print using the IR port and optional A740 printer
• 1 ppm sensitivity
• Measures up to 10,000ppm
• Push on fittings are fast and easy to use
• Large easy to read backlit display
• Advanced electrochemical sensor is field replaceable and calibrateable
• Protective rubber boot and soft carrying case with shoulder strap is included
• Pump driven
• Pump flow block indicator
• Auto zero

Applications

• Ambient CO safety checks
• Checking flue gasses at home or office spaces for the presence and location of carbon monoxide

TPI 707 Flue Gas Analyzer comes complete with the following standard accessories:

• TPI 707 Instrument
• Rubber Boot (A765)
• Soft Carrying Case (A787)
• Flue Sampling Probe (A69)
• In-Line Filter assembly installed on Flue probw (A794)
• Mini Pump Protection Filter Assembly and spare filters (A763)
• Exhaust Spigot (removable) (A764)
• Instruction Manual

TPI 707 Flue Gas Analyzer has the following options available:

• Infrared printer (A740)
• Spare In-Line Filter (A794F is a package of 5 filters)
• Spare Water Block Filter (A794W is a package of 1 filter).

319C Calibratable Pocket Digital Thermometer with Contact Tip by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Contact Tip
• Field calibrateable to ±2°F
• Rugged and waterproof (IP63)
• Auto off
• -Magnetic clip perfect for air duct applications
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

Package Includes: Nano-Clip only

P250R Non-Switchable Passive Oscilloscope Probe, 250MHz, x 100 with Readout, 1.2M Cable Length by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

P250 Non-Switchable Passive Oscilloscope Probe, 250MHz, 1.2M Cable Length by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

192 True RMS 50,000 count DMM with Inductance by Test Products International

The Triple Display 192 is an innovative new concept in DMM design. The unique display enables you to view more than one event at a time. This eliminates the hassle of switching back and forth to review minimum, maximum or preset comparative values. The meter is also easy to use and built to last.

The DMM 192 is a hand-held autoranging DMM. The backlit LCD can display three readings at one time. In addition to basic function of AC/DC V, AC/DC A, Ohm, Diode test, continuity, Capacitance, Frequency, there is the adaptor function. The meter also has RS232 output and software for recording information into a PC.

Features:

• REC: Records Min/Max and Average readings during specified measurement intervals.
• COMP: Compare actual reading to preset HI and LOW value for Pass/Fail testing of component
• Hold: Tow hold system automatically holds the previous stable reading when a new one is obtained.
• Data logging
• 50,000 count display
• 0.05% DCV basic accuracy
• Inductance, Frequency and Capacitance
• 0 to 750 ACV; max resolution 100uV
• 0 to 1,000 DCV: max resolution 0.001mV
• 0 to 50MΩ; max resolution 0.01Ω
• Audible continuity
• AC/DC amps up to10 amps; resolution 0.01 uA
• Analog bar graph
• cULus 61010-1
• CATIII-1000VC, CATIII-1000V, CAT IV-600V, CAT III 1000V
• True RMS DMM
• Time Stamp Logging
• Optional PC Output with A192
• Pulse Width
• Duty cycle (% pulse width modulation) for measuring modulating gas valves

Applications:

• Thermocouples in furnaces or gas applications
• Heat anticipator current in thermostats
• Line voltage
• Control circuit voltage
• Flame safeguard control current
• Heating element resistance (continuity)
• Compressor winding resistance
• Contactor and relay coil resistance
• Continuity of wiring
• Motor start and run capacitance
• Frequency on controls and line voltages
• Record min/max voltage of controls and line voltages
• Temperature with optional temperature adapter (A310)
• Bar graph to indicate rapid fluctuations in measurements
• Voltage of direct drive DC motors
• Measure power supply voltage
• Match components
• Compare readings in circuits and components
• Frequency of line and control voltage

58-900-1M RG58/U, BNC Male to BNC Male, 75 Feet by Test Products International

50 Ohm, 75 Ohm, 93 Ohm. TPI BNC to BNC coax cable assemblies include: RG58/U (molded and assembled), RG59/U and RG62/U.

Features

• UL Listed Cable: Ensures quality and consistency in the cable construction.
• Boot is molded to cable connector for added strength: Limits the amount of bending the cable is exposed to at the connector to prevent cable breakage.
• Gold center pins: Ensures that there is a high quality connection maintaining the best return loss in high definition applications.
• Machined Brass Connectors: Unlike die-cast connectors, machined brass connectors have more precise tolerances, strength and positive mating meaning low signal loss for precise video and data applications.
• Boot is molded to cable connector for added strength
• 95% shielding
• 80°F temperature rating
• Multiple lengths up to 100 feet
• Individually bagged

59-900-1M RG59/U, BNC Male to BNC Male, 75 feet by Test Products International

50 Ohm, 75 Ohm, 93 Ohm. TPI BNC to BNC coax cable assemblies include: RG58/U (molded and assembled), RG59/U and RG62/U.

Features

• UL Listed Cable: Ensures quality and consistency in the cable construction.
• Boot is molded to cable connector for added strength: Limits the amount of bending the cable is exposed to at the connector to prevent cable breakage.
• Gold center pins: Ensures that there is a high quality connection maintaining the best return loss in high definition applications.
• Machined Brass Connectors: Unlike die-cast connectors, machined brass connectors have more precise tolerances, strength and positive mating meaning low signal loss for precise video and data applications.
• Boot is molded to cable connector for added strength
• 95% shielding
• 80°F temperature rating
• Multiple lengths up to 100 feet
• Individually bagged