Test and Measurement, Test Products International

1P20B Non-Switchable Passive Oscilloscope Probe, 15MHz, 1.2M Cable Length by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

265 Clamp-On Tester with Frequency and Capacitance by Test Products International

Perfect for tight, narrow, spaces. The new TPI 265 with slim jaw and body is ideal for cramped work areas and crowded electrical panels.

The 265 is a hand-held, autoranging clamp-on DMM. Extra large numerals, capacitance, frequency and data hold are just a few of the features of the 265. An affordable choice, the 265 offers measurements in all basic electrical functions.

Features:

• Slim jaw and body design for use is crowded electrical panels
• 4,000 count display
• Capacitance range up to 4,000 microfards to test run and start capicitors
• 0.1 DC millivolt resolution to accurately measure thermocouples and use optional adapters
• 0.01 AC Amp resolution to measure heat anticipator current
• Frequency measurement capability
• AC/DC volts up to 600V and AC Amps up to 400A
• Diode, resistance and audible continuity ranges
• Auto / manual ranging
• Data hold
• Auto power off
• CAT III 600V rated
• cULus 61010
• 3-year limited warranty

Applications:

• Test start and run capacitors
• Measure heat anticipator current
• Determine thermocouple voltage
• Test line and control voltages
• Measure heating element resistance
• Measure and adjust variable frequency drives

The 265 comes complete with the following accessories:

• Carrying Pouch
• Test Lead Set
• Instruction Manual
• Battery

270 Clamp-On Tester with Digital Multimetervisit by Test Products International

Perfect for tight, narrow, spaces. The new TPI 270 with slim jaw and body is ideal for cramped work areas and crowded electrical panels.

The slim design 270 is a hand-held, autoranging clamp-on DMM. Extra large numerals, min/max, capacitance, DC microamps and duty cycle are just a few of the features of the 270. An affordable choice, the 270 offers measurements in all basic electrical functions with additional advanced features like non-contact voltage.

Features:

• Measure motor in-rush current and run current
• Measure temperature differential with relative mode
• Non-contact voltage feature can be used to immediately see if power is being supplied to the 24VAC control circuit of thermostats
• Frequency, Min/Max/Record, Data Hold and Peak Hold
• Up to 40,000 Microfarads to test run and start capacitors
• 4,000 count display with 41 segment analog bargraph
• Auto & Manual Ranging
• Low Battery Indicator
• Over Range Indication ("OL")
• Hi Voltage Indicator (>30V AC/DC)
• Auto Power Off after 30 minutes
• Separate Battery/Fuse Compartment
• Low Ohm Range (400V)
• Amps AC Resolution: 0.01A
• VDC/VAC Resolution: 0.1mV
• DC μA measurement (0.01 μA resolution)
• Temperature measurement with 0.1° resolution

Applications:

• Measure flame safety control current
• Test run and start capacitors and motors
• Measure motor run current and capture peak motor start up amperage
• Measure heat anticipator current
• Determine thermocouple voltage
• Test line and control voltages
• Measure heating element resistance
• Measure air temperature in ducts
• Test for the presence of voltage in circuits without contacting the circuit
• Measure temperature differential using relative mode

The 270 comes complete with the following accessories:

• Carrying Pouch
• Test Lead Set
• Temperature Probe
• Instruction Manual
• Battery & Fuse

275 Clamp-On Tester with True RMS Digital Multimeter and 11,000 Count Display by Test Products International

Clamp-On Tester with True RMS Digital Multimeter & 11,000 Count Display. The new TPI 275 with slim jaw and body is ideal for cramped work areas and crowded electrical panels.

The slim design 275 is a hand-held, autoranging clamp-on DMM. Extra large numerals, min/max, capacitance, DC microamps and duty cycle are just a few of the features of the 275. An affordable choice, the 275 offers measurements in all basic electrical functions with additional advanced features like non-contact voltage.

Features:

• True RMS
• 11,000 count display
• Up to 400 amps AC/DC
• Auto & Manual Ranging
• Data Hold
• Low Battery Indicator
• Over Range Indication ("OL")
• Peak Hold
• Min/Max
• Relative Mode
• Hi Voltage Indicator(>30V AC/DC)
• Non-contact voltage detection
• Auto Power Off after 30 minutes
• Separate Battery Compartment
• Low Ohm Range (110Ω)
• Amps AC Resolution: 0.01A
• VDC/VAC Resolution: 0.01mV
• DCiA measurement (0.01μA resolution)
• Temperature measurement

Applications:

• Measure DC amperage of motor drive units
• Measure flame safety control current
• Test run and start capacitors and motors
• Measure motor run current and capture peak motor start up amperage
• Measure heat anticipator current
• Determine thermocouple voltage
• Test line and control voltages
• Measure heating element resistance
• Measure air temperature in ducts
• Test for the presence of voltage in circuits without contacting the circuit
• Measure temperature differential using relative mode

The 275 comes complete with the following accessories:

• Carrying Pouch
• Test Lead Set
• Temperature Probe
• Instruction Manual
• Battery & Fuse

291 Hand-held Manual Ranging Clamp-on DMM by Test Products International

Digital Clamp-On Meter Amp Plus. The 291 is a hand-held manual ranging clamp-on DMM, an affordable choice offering measurements in all basic electrical functions.

The 291 is a hand-held manual ranging clamp-on DMM. The 291 is an affordable choice offering measurements in all basic electrical functions.

• Bar Graph: When measuring frequency, bar graph indicates current level.
• Peak Mode: For start-up and inrush currents.
• Sleep Mode: Preserves battery life.
• Data Hold: Holds the reading on the display for easy viewing.

Features:

• Agency UL Listed to U.S. and Canadian Safety Standards. Meets CE and IEC 1010.
• 4000 Count Improves the resolution on all functions and ranges.
• Data Hold Maintains the reading on the display for hard to reads areas.
• Peak Mode Measure the inrush current of motors, relays and solenoids.
• Sleep Mode Automatically powers down after 10 minutes of inactivity
• 700 Amps AC
• Measure AC/DC volts, resistance and continuity
• CAT III 600 V rated
• cULus 61010
• 3-year limited warranty

Applications:

• Thermocouples in furnaces and gas appliances
• Heat anticipator current in thermostats
• Test line and control voltage
• Compressor winding resistance
• Contactor and relay coil resistance
• Motor and compressor startup current
• Continuity of wiring
• Measure line current
• Test continuity of circuit breakers and fuses
• Measure voltage of direct drive DC motors
• Measure power supply voltage

The 291 comes complete with the following accessories:

• Carrying Pouch
• Test Lead Set
• Temperature Probe
• Instruction Manual
• Battery

293 Clamp-on Plus DMM with True RMS Capabilities by Test Products International

Digital Clamp-On Meter Amp Plus. The 293 is a clamp-on plus DMM with True RMS capabilities. The 293 offers measurements in all basic electrical functions plus:

Features:

• True RMS: Provides accurate and dependable readings of non-linear loads.
• Bar Graph: When measuring frequency, bar graph indicates current level.
• TRIM Mode: Smooths out unstable readings.
• Peak Mode: For start-up and inrush currents.
• Sleep Mode: Preserves battery life.
• Data Hold: Holds the reading on the display for easy viewing.
• Measure AC/DC volts, resistance, continuity and frequency
• CAT III 600 V rated
• cULus 61010
• 3-year limited warranty

Applications:

• Heat anticipator current in thermostats
• Line voltage
• Control circuit voltage
• Heating element resistance
• Compressor winding resistance
• Contactor and relay coil resistance
• Motor and compressor start up current
• Continuity of wiring
• Frequency on control and line voltage
• Record/Min/Max voltage of controls and line voltages
• Bar graph to indicate rapid fluctuations

The 293 comes complete with the following accessories:

• Carrying Pouch
• Test Lead Set
• Instruction Manual
• Battery

296 Clamp-on Plus DMM with True RMS and Harmonics Capabilities by Test Products International

The 296 is a clamp-on plus DMM with True RMS and Harmonics capabilities. The 296 offers measurements in all basic electrical functions, plus.

Features:

• True RMS: Provides accurate and dependable readings of non-linear loads.
• HDR Mode: Determines if a signal is clean or distorted
• Bar Graph: When measuring frequency, bar graph indicates current level.
• TRIM Mode: Smooths out unstable readings.
• Peak Mode: For start-up and inrush currents.
• Sleep Mode: Preserves battery life.
• Data Hold: Holds the reading on the display for easy viewing.
• Measure AC/DC volts, resistance, continuity and frequency
• CAT III 600 V rated
• cULus 61010
• 3-year limited warranty

Applications:

• Heat anticipator current in thermostats
• Line voltage
• Control circuit voltage
• Heating element resistance
• Compressor winding resistance
• Contactor and relay coil resistance
• Motor and compressor start up current
• Continuity of wiring
• Frequency on control and line voltage
• Record/Min/Max voltage of controls and line voltages
• Bar graph to indicate rapid fluctuations

The 296 comes complete with the following accessories:

• Carrying Pouch
• Test Lead Set
• Instruction Manual
• Battery

TPI-3000A Universal Cables & Connector Kit by Test Products International

TPI-3000A Universal Cables & Connector Kit. Technicians and engineers turn to TPI for their connecting needs. With the TPI-3000A and TPI-5000A kits, technicians can create connections on the spot in seconds.

Features

• Includes 8 types of connectors for male and female adapters
• Simply screw on any combination of 24 connectors to any of the six universal interfaces with no soldering or crimping needed
• Reusable connectors can be used over and over in different combinations to fit and assist customizing the installation
• Works with universal cables GEX-60 (36"), GEX-48 (48"), and GEX-75 (72")
• Connector bodies are silver-plated machine brass with PTFE insulation
• Zippered soft case protects and organizes the individual pieces

306C Calibratable Low Cost Pocket Digital Thermometer with A306 by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Field calibrateable to ±2°F
• Easy-to-read LCD
• Data Hold for hard to reach areas
• Penetration tip
• Auto off
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

306XC Calibratable Low Cost Pocket Digital Thermometer (Centigrade Version of the 306) with A306 by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Field calibrateable to ±2°F
• Easy-to-read LCD
• Data Hold for hard to reach areas
• Penetration tip
• Auto off
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

307C Calibratable Low Cost Pocket Digital Thermometer with Needle Tip with A306 by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Compact and convenient
• Easy-to-read, large LCD
• Auto power off
• Data hold for hard to reach areas
• A306 protective rubber boot offers protection from drops
• 307C with needle tip

310C Calibratable Digital Pocket Thermometer with Reversible Head by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Reversible head for best viewing
• Field calibrateable to ± 2°F
• Easy-to-read LCD
• Data Hold for hard to reach areas
• Penetration tip
• Auto off
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

312C Calibratable Water Resistant Digital Pocket Thermometer by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Field calibrateable to ±2°F
• Easy-to-read LCD
• Data Hold for hard to reach areas
• Penetration tip
• Auto off
• 3.1 mm stem for fast response
• 4.9 inch stem for insertion in liquids and semi-solids
• IP Rating IP67
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

315C Calibratable Pocket Digital Thermometer with Magnets by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Auto field calibration to ± 2F
• Tapered stem (3.1 mm diameter) to fit into a Pete's Plug
• Reinforced, heavy-duty housing for strength
• Waterproof (IP63)
• Fits in your pocket
• -58°F to 300°F (-50°C to 150°C)
• Rugged design to withstand a 10 foot drop
• Magnetic clip perfect for air duct applications
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

316C Calibratable Pocket Digital Thermometer without Magnets by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Auto field calibration to ±2°F
• Tapered stem (3.1 mm diameter) to fit into a Pete's Plug
• Reinforced, heavy-duty housing for strength
• -Waterproof (IP63)
• Fits in your pocket
• -58°F to 300°F (-50°C to 150°C)
• Rugged design to withstand a 10 foot drop
• Magnetic clip perfect for air duct applications
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

317C Calibratable Pocket Digital Thermometer with Air Tip by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Air tip
• Field calibrateable to ±2°F
• Rugged and waterproof (IP63)
• 3.1mm stem for "Pete's" plug
• Auto off
• -Magnetic clip perfect for air duct applications
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

318C Calibratable Pocket Digital Thermometer with Chisel Tip by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Field calibrateable to ±2°F
• Rugged and waterproof (IP63)
• Chisel Tip
• Auto off
• -Magnetic clip perfect for air duct applications
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

319C Calibratable Pocket Digital Thermometer with Contact Tip by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Contact Tip
• Field calibrateable to ±2°F
• Rugged and waterproof (IP63)
• Auto off
• -Magnetic clip perfect for air duct applications
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

320C Calibratable Pocket Digital Thermometer with Reduced Diameter Stem by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Penetration-Tip
• Small diameter (1.6mm)

323 Calibratable Water Resistant Digital Pocket Thermometer with Chisel Tip by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Field calibrateable to ±2°F
• Easy-to-read LCD
• Data Hold for hard to reach areas
• Penetration tip
• Auto off
• 3.1 mm stem for fast response
• 4.9 inch stem for insertion in liquids and semi-solids
• IP Rating IP67
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures