Test and Measurement, Test Products International

192 True RMS 50,000 count DMM with Inductance by Test Products International

The Triple Display 192 is an innovative new concept in DMM design. The unique display enables you to view more than one event at a time. This eliminates the hassle of switching back and forth to review minimum, maximum or preset comparative values. The meter is also easy to use and built to last.

The DMM 192 is a hand-held autoranging DMM. The backlit LCD can display three readings at one time. In addition to basic function of AC/DC V, AC/DC A, Ohm, Diode test, continuity, Capacitance, Frequency, there is the adaptor function. The meter also has RS232 output and software for recording information into a PC.

Features:

• REC: Records Min/Max and Average readings during specified measurement intervals.
• COMP: Compare actual reading to preset HI and LOW value for Pass/Fail testing of component
• Hold: Tow hold system automatically holds the previous stable reading when a new one is obtained.
• Data logging
• 50,000 count display
• 0.05% DCV basic accuracy
• Inductance, Frequency and Capacitance
• 0 to 750 ACV; max resolution 100uV
• 0 to 1,000 DCV: max resolution 0.001mV
• 0 to 50MΩ; max resolution 0.01Ω
• Audible continuity
• AC/DC amps up to10 amps; resolution 0.01 uA
• Analog bar graph
• cULus 61010-1
• CATIII-1000VC, CATIII-1000V, CAT IV-600V, CAT III 1000V
• True RMS DMM
• Time Stamp Logging
• Optional PC Output with A192
• Pulse Width
• Duty cycle (% pulse width modulation) for measuring modulating gas valves

Applications:

• Thermocouples in furnaces or gas applications
• Heat anticipator current in thermostats
• Line voltage
• Control circuit voltage
• Flame safeguard control current
• Heating element resistance (continuity)
• Compressor winding resistance
• Contactor and relay coil resistance
• Continuity of wiring
• Motor start and run capacitance
• Frequency on controls and line voltages
• Record min/max voltage of controls and line voltages
• Temperature with optional temperature adapter (A310)
• Bar graph to indicate rapid fluctuations in measurements
• Voltage of direct drive DC motors
• Measure power supply voltage
• Match components
• Compare readings in circuits and components
• Frequency of line and control voltage

P100B Non-Switchable Passive Oscilloscope Probe, 100MHz, 1.2M Cable Length by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

ADF25 Differential Probe by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

Package Includes: Nano-Clip only

725 Pocket Combustible Gas Detector by Test Products International

The 725 offers 1000ppm sensitivity to detect combustible gasses including natural gas, methane, propane (LPG), diesel, and kerosene.

Trace fuel lines, tanks and containers for gas leaks. Once a leak is detected, the 725 will sound an alarm and the red LED s will light showing level of leak.

Features

• 1000ppm sensitivity
• Trace natural gas lines and fittings for leaks
• Check gas equipment for leaks
• Test propane tanks, fittings, lines, and heaters for leaks
• Check propane tanks, fitting lines, and heaters for leaks.
• Test confined spaces for gas build-up
• Fits in shirt pocket
• Responds instantly

Applications

• Check gas generation for leaks

Standard Accessories

• Carrying Pouch (A780)
• Instruction Manual
• Battery and Sensor (Installed and Calibrated)

P250 Non-Switchable Passive Oscilloscope Probe, 250MHz, 1.2M Cable Length by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

P250R Non-Switchable Passive Oscilloscope Probe, 250MHz, x 100 with Readout, 1.2M Cable Length by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

59-048-1M RG59/U, BNC Male to BNC Male, 48 inch by Test Products International

50 Ohm, 75 Ohm, 93 Ohm. TPI BNC to BNC coax cable assemblies include: RG58/U (molded and assembled), RG59/U and RG62/U.

Features

• UL Listed Cable: Ensures quality and consistency in the cable construction.
• Boot is molded to cable connector for added strength: Limits the amount of bending the cable is exposed to at the connector to prevent cable breakage.
• Gold center pins: Ensures that there is a high quality connection maintaining the best return loss in high definition applications.
• Machined Brass Connectors: Unlike die-cast connectors, machined brass connectors have more precise tolerances, strength and positive mating meaning low signal loss for precise video and data applications.
• Boot is molded to cable connector for added strength
• 95% shielding
• 80°F temperature rating
• Multiple lengths up to 100 feet
• Individually bagged

ADF25C Differential Probe by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

IP060 Switchable Passive Oscilloscope Probe, 60MHz, 1.5M Cable Length by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

Package Includes: Nano-Clip only

620 Dual Input Differential Manometer by Test Products International

Dual Differential Input Manometer with ±80 inH2O range and 0.01 in H2O resolution. Auto power off, Backlight display, Zero function, Trim mode to stabilize readings.

The TPI 600 series is a hand held range of pressure meters and can be summarized as follows.

• TPI 610 Single Input - 4 Function - single unit of pressure
• TPI 615 Single Input - 7 Function - 7 units of pressure
• TPI 620 Dual Input differential 4 Function single unit of pressure
• TPI 625 Dual Input differential 7 Function 7 units of pressure

All these models measure over the range of -40.0 to +120.0 mbar. Each unit has increased resolution of 0.01 mbar and automatically auto-ranges at + 19.00 mbar to 0.1 mbar resolution. Each model is supplied complete with carry pouch, battery and instruction manual.

Features:

• Differential input with ± 80" H2O range
• Display - 4 digit with backlight
• Smooth - Stabilizes display when measuring fluctuating pressures
• Auto Off: Conserve battery power

Standard Accessories (Included):

• 9V Alkaline battery (A009A)
• Soft Pouch (A600)
• Silicone Tube with 1/4" barbed 1/8" NPT fitting

Package Includes: Nano-Clip only

739A Gas Leak Detector by Test Products International

Designed to provide personal protection from potential hazardous conditions and help find the source of combustible gases fast!

Features

• Internal Pump
• Water/Dust Filter
• Push Button Operation
• Field Calibration
• Date/Time Display
• Calibration Alert
• Operation Memory
• Calibration Memory
• Infrared Download
• Audible/Visual Alarms
• Backlit LCD
• Programmable Auto Shut Off

Applications

• Gas Leak Survey/Investigations
• Confined Space Monitoring
• Gas Emergency Investigations
• Vessel Testing

Partial List of Users:

• Utilities
• Maintenance
• Fire Departments
• Safety Inspectors
• Home Inspectors
• Water/Sewer

Departments

• Heating Contractors
• Utility Contractors
• Industrial Plants
• Propane Marketers