Test and Measurement, Test Products International

122 Compact DMM with Adapter Range for Optional Accessories, 0.5% DCV Basic Accuracy by Test Products International

When using the Model 122, press the DATA-H button at any time on any function or range to freeze the reading on the LCD display. This function is very useful when measuring in locations where the display is difficult to read.

Features:

• Safety: Meets CE and IEC 1010 requirements. UL Listed.
• Large LCD: Easy to read at all angles and the majority of lighting levels.
• Data Hold: Freeze readings on the display.
• Rubber Boot: Added protection when the instrument is dropped. (120NB does not include boot.)
• Versatile: Use accessories like a carbon monoxide attachment to expand the capabilities of the 122.
• 2,000 mvDC (2 DCV) adapter range
• 2,000 count display
• 0 to 600 volts AC and DC
• 0 to 2,000 ohms
• Audible continuity
• 10 MOHM internal impedance
• 0.5 % DCV basic accuracy
• cULus 61010-1
• CAT II - 1000V, CAT III - 600V

HVAC/R Applications:

• Line voltage
• Control circuit voltage
• Heating element resistance (continuity)
• Compressor winding resistance
• Contactor and relay coil resistance
• Continuity of wiring

Electrical Applications:

• Measure line voltage
• Continuity of circuit breakers
• Voltage of direct drive DC motors.

The 120 comes complete with the following accessories:

• 122 Instrument
• Rubber Boot
• Test Lead Set
• 9V Battery
• Instruction Manual

126 Compact Autoranging DMM with 0.3% DCV Basic Accuracy and 400mA AC/DC Range by Test Products International

The 126 is a hand-held autoranging DMM. The 126 measures ACV, DCV, ACA, DCA, Resistance, Diodes and Continuity.

Features:

• REC: Records Min/Max readings during specified measurement intervals.
• AC/DC:Toggles between AC/DC volts and Amps.
• Data Hold: Holds the reading on the display for easy viewing.
• Auto Off: Preserves battery life. LCD shows oFF when in this mode. Automatically powers down after 30 minutes of inactivity.
• Agency Approval: Meets CE and IEC 1010 requirements.
• 4,000 count display
• 0.3% DCV basic accuracy
• 0 to 600 ACV; max resolution 1mV
• 0 to 40MΩ; max resolution 0.1Ω
• Audible continuity
• 0 to 400 mA amps AC/DC; max resolution 0.01mA
• Autoranging
• Min/Max
• Data Hold
• cULus 61010-1
• CAT II - 1000V, CAT III - 600V

Applications:

• Thermocouples in furnaces or gas applications
• Thermocouples in furnaces of gas applications. DC Controlled circuits
• Heat anticipator current in thermostats
• Line voltage
• Control circuit voltage
• Flame safeguard control current
• Heating element resistance (continuity)
• Compressor winding resistance
• Contactor and relay coil resistance
• Continuity of wiring
• Temperature with optional temperature adapter

The 126 comes complete with the following accessories:

• 126 Instrument
• Rubber Boot
• Test Lead Set
• Battery
• Instruction Manual

133 Manual Ranging DMM, with Boot, Test Leads, Battery and Manual by Test Products International

The 133 is a hand-held autoranging DMM. It features extra large numerals on the LCD, and Data Hold for all functions and ranges. The 133 is an affordable choice offering measurements in all of the basic electrical functions.

Features:

• Safety: Meets CE and IEC 1010 requirements. UL Listed to U.S. and Canadian Safety Standards.
• Large LCD:Easy to read at all angles and the majority of lighting levels. 4000 Count.
• Rubber Boot: Added protection when the instrument is dropped. (135NB does not include boot.)
• Multi-function: Measure all electrical characteristics with one meter.
• 0.5% DCV basic accuracy
• 0 to 750 ACV; max resolution 1mV
• 0 to 1,000 DCV; max resolution 0.1mV
• 0 to 20MΩ; max resolution 0.1Ω
• 0 to 10 amps AC/DC; 0.1uA resolution
• Data Hold
• cULus 61010-1
• CAT II - 1000V, CAT III - 600V

Applications:

• Thermocouples in furnaces and gas appliances
• Heat anticipator current in thermostats
• Line and control voltages
• Flame safety control current
• Heating element resistance
• Continuity of wiring
• Line current up to 10 amps
• Power supply current

The 133 comes complete with the following accessories:

• 133 Instrument
• Rubber Boot (133NB does not include boot)
• Test Lead Set
• Battery
• Instruction Manual

135 Manual Ranging DMM with Capacitance, 40uA Range, with Boot, Test Leads, and Manual by Test Products International

The 135 is a hand-held autoranging DMM. It features extra large numerals on the LCD, and Data Hold for all functions and ranges. The 135 is an affordable choice offering measurements in all of the basic electrical functions.

Features:

• Safety: Meets CE and IEC 1010 requirements. UL Listed to U.S. and Canadian Safety Standards.
• Large LCD:Easy to read at all angles and the majority of lighting levels. 4000 Count.
• Rubber Boot: Added protection when the instrument is dropped. (135NB does not include boot.)
• Multi-function: Measure all electrical characteristics with one meter.
• 0.5% DCV basic accuracy
• 0 to 750 ACV; max resolution 1mV
• 0 to 1,000 DCV; max resolution 0.1mV
• 0 to 40MΩ; max resolution 0.1Ω
• 0 to 10 amps AC/DC; 0.1uA resolution
• Data Hold
• cULus 61010-1
• CAT II - 1000V, CAT III - 600V

Applications:

• Thermocouples in furnaces and gas appliances
• Heat anticipator current in thermostats
• Line voltages
• Voltage of direct drive DC motors
• Control circuit voltage
• Motor run and start capacitors
• Flame safeguard control current
• Heating element resistance (continuity)
• Compressor winding resistance
• Contactor and relay coil resistance
• Continuity of wiring
• Temperature with optional temperature adapter

The 135 comes complete with the following accessories:

• 135 Instrument
• Rubber Boot
• Test Lead Set
• Battery
• Instruction Manual

153 Autoranging DMM with Boot, Test Leads, Battery and Manual by Test Products International

The 153 is a hand-held autoranging DMM. The 153 measures ACV, DCV, ACA, DCA, Resistance, Diodes and Continuity.

Features:

• Agency Approval: Meets CE and IEC 1010 requirements. UL Listed to U.S. and Canadian Safety Standards.
• Sleep: Instrument automatically powers down after 30 minutes of inactivity, however, it will continue acquiring data in its various modes. Pressing any push button or turning the rotarty switch returns the 153 back to normal.
• Range: Allows you to either manual range or use auto range to select the appropriate range.
• Auto Off: Preserves battery life. LCD shows oFF when in this mode.
• Record: Records Min/Max values.M
• Data Hold: Holds the reading on the display for easy viewing.
• 0.3% DCV basic accuracy
• 0 to 750 ACV; max resolution 1mV
• 0 to 1,000 DCV; max resolution 0.1mV
• 0 to 40MΩ; max resolution 0.1Ω
• AC/DC amps to 10; max resolution 0.1uA
• Min/Max
• cULus 61010-1
• CAT II - 1000V, CAT III - 600V

Applications:

• Thermocouples in furnaces or gas applications
• Heat anticipator current in thermostats
• Line voltage
• Voltage of direct drive DC motors
• Control circuit voltage
• Motor run and start capacitors
• Flame safeguard control current
• Heating element resistance (continuity)
• Compressor winding resistance
• Contactor and relay coil resistance
• Continuity of wiring
• Continuity of circuit breakers
• Temperature with optional temperature adapter
• Bar graph to indicate rapid fluctuations in measurements

The 153 comes complete with the following accessories:

• Rubber Boot
• Test Lead Set
• Battery
• Instruction Manual

163 Autoranging DMM with Bar Graph, Boot, Test Leads, and Manual by Test Products International

The 163 is a hand-held autoranging DMM. The 163 measures ACV, DCV, ACA, DCA, Resistance, Diodes and Continuity.

Features:

• Safety: Meets CE and IEC 1010 requirements. UL Listed to U.S. and Canadian Safety Standards.
• Data Hold: Holds the reading on the display.
• Range: Allows you to either manual range or use auto range to select the appropriate range.
• Auto Off: Preserves battery life. LCD shows oFF when in this mode.
• Large LCD: Easy to read at all angles and the majority of lighting levels.
• Rubber Boot: Added protection when the instrument is dropped.
• 0.5% DCV basic accuracy
• 0 to 750 ACV; max resolution 1mV
• 0 to 1,000 DCV; max resolution 0.1mV
• 0 to 32.6MΩ; max resolution 0.1Ω
• Audible continuity
• 0 to 10 amps AC/DC; max resolution 0.1uA
• Analog bar graph
• cULus 61010-1
• CAT II - 1000V, CAT III - 600V

Applications:

• Thermocouples in furnaces or gas applications
• Heat anticipator current in thermostats
• Line voltage
• Voltage of direct drive DC motors
• Control circuit voltage
• Motor run and start capacitors
• Flame safeguard control current
• Heating element resistance (continuity)
• Compressor winding resistance
• Contactor and relay coil resistance
• Continuity of wiring
• Continuity of circuit breakers
• Temperature with optional temperature adapter
• Bar graph to indicate rapid fluctuations in measurements

The 163 comes complete with the following accessories:

• Rubber Boot
• Test Lead Set
• Battery
• Instruction Manual

183A True RMS DMM with Temperature, Capacitance, Duty Cycle and Low-pass Filter by Test Products International

The 183A is a hand-held autoranging DMM. The 183A measures ACV, DCV, ACA, DCA, Resistance, Frequency, Duty Cycle, Diodes, Capacitance, Temperature and Continuity. The meter is also easy to use and built to last.

Features:

• REC: Records Min/Max and Average readings during specified measurement intervals.
• Range: Allows the user to manually range the 183A instead of autoranging.
• Hold: Holds the reading on the display for easy viewing.
• REL: Displays the value as a difference to a reference value.
• Auto Off: Preserves battery life.
• Rubber Boot: Added protection when the instrument is dropped.
• 0.5% DCV basic accuracy
• 0 to 750 ACV; max resolution 1mV
• 0 to 1,000 DCV; max resolution 0.1mV
• 0 to 32.6MΩ; max resolution 0.1Ω
• Audible continuity
• 0 to 10 amps AC/DC; max resolution 0.1uA
• Analog bar graph
• cULus 61010-1
• CAT II - 1000V, CAT III - 600V

Applications:

• Thermocouples in furnaces or gas applications
• Heat anticipator current in thermostats
• Line voltage
• Voltage of direct drive DC motors
• Control circuit voltage
• Motor run and start capacitors
• Flame safeguard control current
• Heating element resistance (continuity)
• Compressor winding resistance
• Contactor and relay coil resistance
• Continuity of wiring
• Continuity of circuit breakers
• Temperature with optional temperature adapter
• Bar graph to indicate rapid fluctuations in measurements

The 183A comes complete with the following accessories:

• 183A Instrument
• Zippered Vinyl Carrying Case
• Rubber Boot
• Test Lead Set
• Instruction Manual

194 True RMS 50,000 Count DMM with CAT IV, 1000V Rating with A106 and GK13M by Test Products International

The Triple Display 194 is an innovative new concept in DMM design. The unique display enables you to view more than one event at a time. This eliminates the hassle of switching back and forth to review minimum, maximum or preset comparative values. The meter is also easy to use and built to last.

The DMM 194 is a hand-held autoranging DMM. The backlit LCD can display three readings at one time. In addition to basic function of AC/DC V, AC/DC A, Ohm, Diode test, continuity, Capacitance, Frequency, there is the adaptor function. The meter also has RS232 output and software for recording information into a PC

Features:

• REC: Records Min/Max and Average readings during specified measurement intervals.
• COMP: Compare actual reading to preset HI and LOW value for Pass/Fail testing of component
• Hold: Tow hold system automatically holds the previous stable reading when a new one is obtained.
• Data logging
• 50,000 count display
• 0.05% DCV basic accuracy
• Inductance, Frequency and Capacitance
• 0 to 750 ACV; max resolution 100uV
• 0 to 1,000 DCV: max resolution 0.001mV
• 0 to 50MΩ; max resolution 0.01Ω
• Audible continuity
• AC/DC amps up to10 amps; resolution 0.01 uA
• Analog bar graph
• cULus 61010-1
• CATIII-1000VC, CATIII-1000V, CAT IV-600V, CAT III 1000V
• True RMS DMM
• Time Stamp Logging
• Optional PC Output with A192
• Pulse Width
• Duty cycle (% pulse width modulation) for measuring modulating gas valves

Applications:

• Thermocouples in furnaces or gas applications
• Heat anticipator current in thermostats
• Line voltage
• Control circuit voltage
• Flame safeguard control current
• Heating element resistance (continuity)
• Compressor winding resistance
• Contactor and relay coil resistance
• Continuity of wiring
• Motor start and run capacitance
• Frequency on controls and line voltages
• Record min/max voltage of controls and line voltages
• Temperature with optional temperature adapter (A310)
• Bar graph to indicate rapid fluctuations in measurements
• Voltage of direct drive DC motors
• Measure power supply voltage
• Match components
• Compare readings in circuits and components
• Frequency of line and control voltage

196 Process Meter by Test Products International

The Triple Display 196 is an innovative new concept in DMM design. The unique display enables you to view more than one event at a time. This eliminates the hassle of switching back and forth to review minimum, maximum or preset comparative values. The meter is also easy to use and built to last.

The DMM 196 is a hand-held autoranging DMM. The backlit LCD can display three readings at one time. In addition to basic function of AC/DC V, AC/DC A, Ohm, Diode test, continuity, Capacitance, Frequency, there is the adaptor function. The DMM 196 also has RS232 output and software for recording information into a PC.

Features:

• REC: Records Min/Max and Average readings during specified measurement intervals.
• COMP:Compare actual reading to preset HI and LOW value for Pass/Fail testing of component
• Hold: Tow hold system automatically holds the previous stable reading when a new one is obtained.
• Large 50,000 count display: increases resolution and improves accuracy (1.7" x 2.75", 43mm x 70mm)
• 0-24mA output: t for process controls
• Triple Display: shows more than one reading simultaneously
• 51 Segment Analog Bar Graph: to catch fast AC fluctuations
• Logic Test: Indicates transitions up to 2 MHz.
• Frequency Counter: Measure low frequency signals from 1Hz to 2 MHz and display duty cycle, pulse width and period.
• Back Light (LED Type) allows viewing in any light condition
• Auto Range automatically selects the best range for the measurement
• Separate battery and fuse compartment for easy replacement
• Auto Power Off DMM will automatically power down after approximately 15 minutes of inactivity to extend battery life. Disable Auto Power Off: Hold down the REC button and turn the meter on
• Increased safety with Silicone rubber 1,000V CAT III, 600V CAT IV, 10A test leads (CE & cUL listed)
• Diode Test displays approximate forward bias voltage
• Process DMM with 0 to 24mA output
• 0.05% DCV basic accuracy
• 0 to 750 ACV; max resolution 100uV
• 0 to 1,000 DCV: max resolution 0.001mV
• 0 to 50MΩ; max resolution 0.01Ω
• Audible continuity
• AC/DC amps up to10 amps; resolution 0.01 uA
• Analog bar graph
• cULus 61010-1

Applications:

• View industrial signals such as motor control, UPS, switching power supplies, and PLC controls with 1MHz bandwidth
• Capture noise spikes, glitches, and intermittents with 20 megasamples per second sampling rate
• Full autoranging, True RMS, DMM capabilities
• Measure resistance and test for continuity
• Continually updated display provides a live presentation
• Water Purification
• Chemical Processing
• Oil & Gas
• Power Generation
• Pulp & Paper
• Food & Beverage