Test and Measurement, Test Products International

708OIL 708 Combustion Efficiency Analyzer Kit by Test Products International

708 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature

Includes

• 708 Combustion Efficiency Analyzer
• A788 Smoke Test Pump

709 Combustion Efficiency Analyzer and Differential Manometer by Test Products International

The carbon monoxide sensor used in TPI combustion efficiency analyzers feature an on-board filter capable of filtering NO (nitric oxide), NO₂ (nitrogen dioxide) and NOX (combination of NO and NO₂) to prevent cross sensitivity errors.

Use TPI analyzers to test flue gases in gas and oil fired equipment including high efficiency furnaces and condensing boilers. Measure CO, O₂, and stack temperature.

Determine combustion efficiency, CO₂, and CO air free. Built-in differential manometer, combustible gas detection, PC communication, data logging, and can measure NO / NOX.

Features

Using TPI analyzers to determine combustion efficiency at the time of equipment set up minimizes call backs and can be used to verify to the home owner the value of service work by showing the increase in equipment efficiency after work is performed. Efficiency calculation can also be used to generate business by demonstrating the need to improve the efficiency of equipment or to show the benefit of purchasing new equipment with higher efficiency.

Quick And Simple Set Up

All TPI analyzers feature quick and simple set up. Fast purge and the ability to perform fuel selectionduring start up enable tests to be performed quickly without requiring extra set-up time after initial startup. TPI analyzers also use the last selected fuel as the default setting. This feature prevents the need toperform fuel selection every time the analyzer is turned on.

• High resolution 0.001 in H20 differential manometer for high efficiency and oil equipment
• Measure CO, and temperature
• Calculate CO2, efficiency, excess air, and CO air free
• Pump driven for fast response
• Will not shut off if 15 ppm CO is present for increased safety
• Ten selectable fuels: Natural Gas, LPG, Light Oil, Heavy Oil, Bituminous Coal, Anthracite Coal, Coke, Butane, Wood, Bagasse
• Optional A740 IR printer available for hard copies of test results
• Built-in differential thermometer
• Store function to save up to 50 readings
• Large easy to read backlit display

Applications

• Tuning of residential and furnaces and domestic boilers
• Ambient and stack testing for CO
• CO safety measurements in and around combustion sources
• Temperature checking, including superheat and hydronic differential temperatures
• Dual input differential manometer

709A740 709 Combustion Efficiency Analyzer Kit by Test Products International

709 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature
• Dual input pressure with 0.001 inches water resolution for high efficiency & oil

A740 Features

• Easy to use
• Battery operated
• Self test facility
• Adjustable contrast
• Manual paper feed
• Maximum transmitting distance 16"(45cm)

709A740 709 Combustion Efficiency Analyzer Kit by Test Products International

709 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature
• Dual input pressure with 0.001 inches water resolution for high efficiency & oil

A740 Features

• Easy to use
• Battery operated
• Self test facility
• Adjustable contrast
• Manual paper feed
• Maximum transmitting distance 16"(45cm)

A773

Use the A773 when working on oil fired appliances to extend the life of your sensors by eliminating acid gas exposure to your analyzer

709A740 709 Combustion Efficiency Analyzer Kit by Test Products International

709 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature
• Dual input pressure with 0.001 inches water resolution for high efficiency & oil

A740 Features

• Easy to use
• Battery operated
• Self test facility
• Adjustable contrast
• Manual paper feed
• Maximum transmitting distance 16"(45cm)

A773

Use the A773 when working on oil fired appliances to extend the life of your sensors by eliminating acid gas exposure to your analyzer

A790

Measures oil pressure

A788

Included with test pump:

• Smoke pump tester
• Smoke pump test paper
• Smoke scale

709OIL 709 Combustion Efficiency Analyzer Kit by Test Products International

709 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature
• Dual input pressure with 0.001 inches water resolution for high efficiency & oil

Includes

• 709 Combustion Efficiency Analyzer
• A773 Sulfer Filter
• A790 Analog Oil Pressure Gauge
• A788 Smoke Pump Test

709R Combustion Efficiency Analyzer with Differential Manometer by Test Products International

The carbon monoxide sensor used in TPI combustion efficiency analyzers feature an on-board filter capable of filtering NO (nitric oxide), NO₂ (nitrogen dioxide) and NOX (combination of NO and NO₂) to prevent cross sensitivity errors.

Use TPI analyzers to test flue gases in gas and oil fired equipment including high efficiency furnaces and condensing boilers. Measure CO, O₂, and stack temperature.

Determine combustion efficiency, CO₂, and CO air free. Built-in differential manometer, combustible gas detection, PC communication, data logging, and can measure NO / NOX.

Features

Using TPI analyzers to determine combustion efficiency at the time of equipment set up minimizes call backs and can be used to verify to the home owner the value of service work by showing the increase in equipment efficiency after work is performed. Efficiency calculation can also be used to generate business by demonstrating the need to improve the efficiency of equipment or to show the benefit of purchasing new equipment with higher efficiency.

Quick And Simple Set Up

All TPI analyzers feature quick and simple set up. Fast purge and the ability to perform fuel selection during start up enable tests to be performed quickly without requiring extra set-up time after initial startup. TPI analyzers also use the last selected fuel as the default setting. This feature prevents the need to perform fuel selection every time the analyzer is turned on.

• High resolution 0.001 in H20 differential manometer for high efficiency and oil equipment
• Measure CO, and temperature
• Calculate CO2, efficiency, excess air, and CO air free
• Pump driven for fast response
• Will not shut off if 15 ppm CO is present for increased safety
• Ten selectable fuels: Natural Gas, LPG, Light Oil, Heavy Oil, Bituminous Coal, Anthracite Coal, Coke, Butane, Wood, Bagasse
• Optional A740 IR printer available for hard copies of test results
• Built-in differential thermometer
• Store function to save up to 50 readings
• Large easy to read backlit display
• Rechargeable Ni-MH Battery with > 6 Hours battery life

Applications

• Tuning of residential and furnaces and domestic boilers
• Ambient and stack testing for CO
• CO safety measurements in and around combustion sources
• Temperature checking, including superheat and hydronic differential temperatures
• Dual input differential manometer

709RA740 709R Combustion Efficiency Analyzer Kit by Test Products International

Features

Using TPI analyzers to determine combustion efficiency at the time of equipment set up minimizes call backs and can be used to verify to the home owner the value of service work by showing the increase in equipment efficiency after work is performed. Efficiency calculation can also be used to generate business by demonstrating the need to improve the efficiency of equipment or to show the benefit of purchasing new equipment with higher efficiency.

Quick And Simple Set Up

All TPI analyzers feature quick and simple set up. Fast purge and the ability to perform fuel selection during start up enable tests to be performed quickly without requiring extra set-up time after initial startup. TPI analyzers also use the last selected fuel as the default setting. This feature prevents the need to perform fuel selection every time the analyzer is turned on.

• High resolution 0.001 in H20 differential manometer for high efficiency and oil equipment
• Measure CO, and temperature
• Calculate CO2, efficiency, excess air, and CO air free
• Pump driven for fast response
• Will not shut off if 15 ppm CO is present for increased safety
• Ten selectable fuels: Natural Gas, LPG, Light Oil, Heavy Oil, Bituminous Coal, Anthracite Coal, Coke, Butane, Wood, Bagasse
• Optional A740 IR printer available for hard copies of test results
• Built-in differential thermometer
• Store function to save up to 50 readings
• Large easy to read backlit display
• Rechargeable Ni-MH Battery with > 6 Hours battery life

A740 Features

• Easy to use
• Battery operated
• Self test facility
• Adjustable contrast
• Manual paper feed
• Maximum transmitting distance 16"(45cm)

712 Deluxe Combustion Efficiency Analyzer with Optional PC Interface by Test Products International

The carbon monoxide sensor used in TPI combustion efficiency analyzers feature an on-board filter capable of filtering NO (nitric oxide), NO₂ (nitrogen dioxide) and NOX (combination of NO and NO₂) to prevent cross sensitivity errors.

Use TPI analyzers to test flue gases in gas and oil fired equipment including high efficiency furnaces and condensing boilers. Measure CO, O₂, and stack temperature.

Determine combustion efficiency, CO₂, and CO air free. Built-in differential manometer, combustible gas detection, PC communication, and data logging.

Features

Using TPI analyzers to determine combustion efficiency at the time of equipment set up minimizes call backs and can be used to verify to the home owner the value of service work by showing the increase in equipment efficiency after work is performed. Efficiency calculation can also be used to generate business by demonstrating the need to improve the efficiency of equipment or to show the benefit of purchasing new equipment with higher efficiency.

Quick And Simple Set Up

All TPI analyzers feature quick and simple set up. Fast purge and the ability to perform fuel selectionduring start up enable tests to be performed quickly without requiring extra set-up time after initial startup. TPI analyzers also use the last selected fuel as the default setting. This feature prevents the need toperform fuel selection every time the analyzer is turned on.

• High resolution 0.001 in H20 differential manometer for high efficiency and oil equipment
• Measure CO, and temperature
• Calculate CO2, efficiency, excess air, and CO air free
• Pump driven for fast response
• Will not shut off if 15 ppm CO is present for increased safety
• Ten selectable fuels: Natural Gas, LPG, Light Oil, Heavy Oil, Bituminous Coal, Anthracite Coal, Coke, Butane, Wood, Bagasse
• Optional A740 IR printer available for hard copies of test results
• Built-in differential thermometer
• Store function to save up to 50 readings
• Large easy to read backlit display
• Rechargeable Ni-MH Battery with > 6 Hours battery life
• Optional Bluetooth interface
• Checks combustibles in flue, optional PC interface

Applications

• Tuning of residential and furnaces and domestic boilers
• Ambient and stack testing for CO
• CO safety measurements in and around combustion sources
• Temperature checking, including superheat and hydronic differential temperatures
• Detecting gas leak in gas lines and around gas fueled appliances. Dual input differential manometer with 3 selectable units of measure: kPa, mBar,inH20

712A740 712 Combustion Efficiency Analyzer Kit by Test Products International

712 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature
• Dual input pressure with 0.001 inches water resolution for high efficiency & oil
• Optional A767 adapter for PC interface

A740 Features

• Easy to use
• Battery operated
• Self test facility
• Adjustable contrast
• Manual paper feed
• Maximum transmitting distance 16"(45cm)

712A740C1 712 Combustion Efficiency Analyzer Kit by Test Products International

712 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature
• Dual input pressure with 0.001 inches water resolution for high efficiency & oil
• Optional A767 adapter for PC interface

A740 Features

• Easy to use
• Battery operated
• Self test facility
• Adjustable contrast
• Manual paper feed
• Maximum transmitting distance 16"(45cm)

A773

Use the A773 when working on oil fired appliances to extend the life of your sensors by eliminating acid gas exposure to your analyzer

712A740OIL 712 Combustion Efficiency Analyzer Kit by Test Products International

712 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature
• Dual input pressure with 0.001 inches water resolution for high efficiency & oil
• Optional A767 adapter for PC interface

A740 Features

• Easy to use
• Battery operated
• Self test facility
• Adjustable contrast
• Manual paper feed
• Maximum transmitting distance 16"(45cm)

Includes

• 712 Combustion Efficiency Analyzer
• A740 IR Printer
• A773 Sulfer Filter
• A790 Analog Oil Pressure Gauge
• A788 Smoke Pump Test

712C5 712 Combustion Efficiency Analyzer Kit by Test Products International

712 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature
• Dual input pressure with 0.001 inches water resolution for high efficiency & oil
• Optional A767 adapter for PC interface

270 Features:

• Measure motor in-rush current and run current
• Measure temperature differential with relative mode
• Non-contact voltage feature can be used to immediately see if power is being supplied to the 24VAC control circuit of thermostats
• Frequency, Min/Max/Record, Data Hold and Peak Hold
• Up to 40,000 Microfarads to test run and start capacitors
• 4,000 count display with 41 segment analog bargraph
• Auto & Manual Ranging
• Low Battery Indicator
• Over Range Indication ("OL")
• Hi Voltage Indicator (>30V AC/DC)
• Auto Power Off after 30 minutes
• Separate Battery/Fuse Compartment
• Low Ohm Range (400V)
• Amps AC Resolution: 0.01A
• VDC/VAC Resolution: 0.1mV
• DC μA measurement (0.01 μA resolution)
• Temperature measurement with 0.1° resolution

Includes

• 712 Combustion Efficiency Analyzer
• 270 Clamp-On Tester with Digital Multimetervisit

712C7 712 Combustion Efficiency Analyzer Kit by Test Products International

712 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature
• Dual input pressure with 0.001 inches water resolution for high efficiency & oil
• Optional A767 adapter for PC interface

270 Features:

• Measure motor in-rush current and run current
• Measure temperature differential with relative mode
• Non-contact voltage feature can be used to immediately see if power is being supplied to the 24VAC control circuit of thermostats
• Frequency, Min/Max/Record, Data Hold and Peak Hold
• Up to 40,000 Microfarads to test run and start capacitors
• 4,000 count display with 41 segment analog bargraph
• Auto & Manual Ranging
• Low Battery Indicator
• Over Range Indication ("OL")
• Hi Voltage Indicator (>30V AC/DC)
• Auto Power Off after 30 minutes
• Separate Battery/Fuse Compartment
• Low Ohm Range (400V)
• Amps AC Resolution: 0.01A
• VDC/VAC Resolution: 0.1mV
• DC μA measurement (0.01 μA resolution)
• Temperature measurement with 0.1° resolution

A740 Features

• Easy to use
• Battery operated
• Self test facility
• Adjustable contrast
• Manual paper feed
• Maximum transmitting distance 16"(45cm)

Includes

• 712 Combustion Efficiency Analyzer
• 270 Clamp-On Tester with Digital Multimetervisit
• A740 IR Printer

715 High CO Combustion Analyzer with Built-in Differential Thermometer, Differential Manometer, and NO Measurement & NOX Calculation by Test Products International

The carbon monoxide sensor used in TPI combustion efficiency analyzers feature an on-board filter capable of filtering NO (nitric oxide), NO₂ (nitrogen dioxide) and NOX (combination of NO and NO₂) to prevent cross sensitivity errors.

Use TPI analyzers to test flue gases in gas and oil fired equipment including high efficiency furnaces and condensing boilers. Measure CO, O₂, and stack temperature.

Determine combustion efficiency, CO₂, and CO air free. Some models include built-in differential manometer, combustible gas detection, PC communication, data logging, and can measure NO / NOX.

Use the optional A784 flow regulator to reduce the flow rate of the gas being sampled to measurable levels on high pressure systems such as gas compression engines. The A784 is included in the 715K3 kit.

Features

Using TPI analyzers to determine combustion efficiency at the time of equipment set up minimizes call backs and can be used to verify to the home owner the value of service work by showing the increase in equipment efficiency after work is performed. Efficiency calculation can also be used to generate business by demonstrating the need to improve the efficiency of equipment or to show the benefit of purchasing new equipment with higher efficiency.

Quick And Simple Set Up

All TPI analyzers feature quick and simple set up. Fast purge and the ability to perform fuel selection during start up enable tests to be performed quickly without requiring extra set-up time after initial startup. TPI analyzers also use the last selected fuel as the default setting. This feature prevents the need toperform fuel selection every time the analyzer is turned on.

• Measure up to 9.999% CO
• Built-in differential thermometer
• Measure NO (Nitric Oxide), Calculate NOx
• Store function to save up to 10 readings
• Calculates combustion efficiency
• Pump driven for fast response
• Push on fittings for fast and easy use
• Large easy to read backlit display
• Will not shut off if 15 ppm CO is present for increased safety
• Four selectable fuels: Natural Gas, LPG, Light Oil, Heavy Oil
• Optional A740 IR printer available for hard copies of test results

Applications

• Tune combustion engines
• Test CO levels in industrial boilers
• Measure NO and calculate NOX

716A740 716 Flue Gas Analyzer Kit by Test Products International

Features

• Built-in differential manometer with 0.001 H2O resolution
• Calculates combustion efficiency
• Data Logging with time and date stamp
• Will not shut off if 15 ppm CO is present for increased safety
• Communicate to a PC via the USB interface
• Optional A740 IR printer available for hard copies of test results
• Built-in differential thermometer
• Push on fittings for fast and easy use
• Optional Bluetooth interface

A740 Features

• Easy to use
• Battery operated
• Self test facility
• Adjustable contrast
• Manual paper feed
• Maximum transmitting distance 16"(45cm)

Includes

• 716 Flue Gas Analyzer
• A740 IR Printer

716N New Combustion Analyzer with Graphical Display and Combustible Gas Leak Check Wand and NOX by Test Products International

The TPI Model 716N Flue Gas Analyzer is a state of the art, easy to use analyzer designed not only to display and calculate the required readings from a flue but also to cover most of the other measurements associated with combustion.

Features

Using TPI analyzers to determine combustion efficiency at the time of equipment set up minimizes call backs and can be used to verify to the home owner the value of service work by showing the increase in equipment efficiency after work is performed. Efficiency calculation can also be used to generate business by demonstrating the need to improve the efficiency of equipment or to show the benefit of purchasing new equipment with higher efficiency.

• Built-in differential manometer with 0.001" H2O resolution
• Measure NO (Nitric Oxide), Calculate NOX
• Calculates combustion efficiency
• Data Logging with time and date stamp
• Will not shut off if 15 ppm CO is present for increased safety
• Communicate to a PC via the USB interface
• Optional A740 IR printer available for hard copies of test results
• Built-in differential thermometer
• Store function to save up to 10 readings
• Pump driven for fast response
• Push on fittings for fast and easy use
• Large easy to read backlit display
• Ten selectable fuels
• Optional Bluetooth interface

Applications

• Tuning of residential and furnaces and domestic boilers
• Ambient and stack testing for CO
• CO safety measurements in and around combustion sources
• Temperature checking, including superheat and hydronic differential temperatures
• Dual input differential manometer with 3 selectable units of measure: kPa, mBar, inH20

Quick And Simple Set Up

All TPI analyzers feature quick and simple set up. Fast purge and the ability to perform fuel selectionduring start up enable tests to be performed quickly without requiring extra set-up time after initial startup. TPI analyzers also use the last selected fuel as the default setting. This feature prevents the need toperform fuel selection every time the analyzer is turned on.

The TPI 716N Flue Gas Analyzer comes complete with the following standard accessories:

• TPI 716N Analyzer
• Combustible Gase Leak Probe (A806)
• Rubber Boot (A765) 1 each installed on analyzer
• Soft Carrying Case (A768) - 1 each
• Flue Sampling Probe (A770) - 1 each
• In-Line Filter / Water Trap installed on Flue probe (A795) - 1 each
• Disc water filter installed in water trap (A794W) - 1 each
• Spare In-Line Filter - 1 each (A794F is a package of 5 filters)
• Temperature Probe (GK11M) - 1 each
• Battery Charger (A766) - 1 each
• Mini Pump Protection Filter Assembly (A763) - 1 each
• Exhaust Spigot Removable (A764) - 1 each
• Pressure Tubing (A774) - 1 each 6 piece
• Static Pressure Tips (A776) - 2 each
• 1/4" barbed to 1/8" NPT fitting (A603) - 2 each
• Gas Valve Adapter (A611) - 1 each
• Adapter Tubing (A791) - 1 each 4" piece
• Instruction Manual

The TPI 716 Flue Gas Analyzer has the following options available:

• A807 PC Software and cable for communication to a PC.
• A740 infrared printer (Included with 716A740)

716NA740 716N New Combustion Analyzer Kit by Test Products International

Features

• Built-in differential manometer with 0.001" H2O resolution
• Measure NO (Nitric Oxide), Calculate NOX
• Calculates combustion efficiency
• Data Logging with time and date stamp
• Will not shut off if 15 ppm CO is present for increased safety
• Communicate to a PC via the USB interface
• Optional A740 IR printer available for hard copies of test results
• Built-in differential thermometer
• Store function to save up to 10 readings
• Pump driven for fast response
• Push on fittings for fast and easy use
• Large easy to read backlit display
• Ten selectable fuels
• Optional Bluetooth interface

A740 Features

• Easy to use
• Battery operated
• Self test facility
• Adjustable contrast
• Manual paper feed
• Maximum transmitting distance 16"(45cm)

Includes

• 716N New Combustion Analyzer
• A740 IR Printer

719 Combustible Gas Leak Detector by Test Products International

The 719 offers 30ppm sensitivity to detect combustible gasses. Easily operated with one hand, leaks are pinpointed using the audio and visual indicators. An adjustable tic rate helps eliminate background gas concentration in contaminated environments.

The 719 is easy to use and is built to last. It is backed by a 3 year limited warranty. Please remember to complete and return your product warranty registration card.

Features

• Instant response
• 30 ppm (methane) sensitivity
• Adjustable tic rate
• One-hand operation
• Visual and audible leak indication
• 16'' gooseneck
• Soft carrying pouch

Applications

• Detect combustible gasses including natural gas methane, propane (LPG), gasoline, diesel, and kerosene
• Trace natural gas lines and fittings for leaks
• Check gas generation for leaks

The 719 comes complete with the following accessories:

• Carrying Pouch (A780)
• Instruction Manual
• Battery and Sensor (Installed and Calibrated)

720B Combustible Gas Leak Detector by Test Products International

The 720B offers 10ppm sensitivity to detect combustible gasses. Easily operated with one hand, leaks are pinpointed using the audio and visual indicators. An adjustable tic rate helps eliminate background gas concentration in contaminated environments.

The 720b is an advanced state-of-the-art leak detector capable of detecting many combustible, noncombustible and toxic gases.

Features

• Instant response
• 10 ppm (methane) sensitivity
• Adjustable tic rate
• One-hand operation
• Visual and audible leak indication
• 16" gooseneck
• Soft carrying pouch
• Measurement capability

Applications

• Detect combustible gasses including natural gas methane, propane (LPG), gasoline, diesel, and kerosene
• Trace natural gas lines and fittings for leaks
• Check gas generation for leaks

The following is a partial list of gases that the 720b is sensitive to:

Acetone, Alcohol, Ammonia, Steam, Carbon Monoxide*, Butane, Gasoline, Jet Fuel, Hydrogen Sulfide, Smoke, Industrial Solvents, Methane, Lacquer Thinner, Naphtha, Propane, Natural Gas.

Standard accessories

• Sensor (A739)
• Instruction Manual: 720b Instruction Manual
• Soft Pouch (A700)

Optional accessories

• Hard Case (A714)
• Earphone (A710)

721 Combustible Gas Leak Detector with LCD Display by Test Products International

The 721 offers 10ppm sensitivity to detect combustible gasses. Easily operated with one hand, leaks are pinpointed using the audio and visual indicators. An adjustable tic rate helps eliminate background gas concentration in contaminated environments.

The ergonomically designed 721 is a hand-held, combustible gas leak detector. It is capable of finding combustible gas leaks in pipes, fittings, regulators, etc. Additional features include the capability to display %LEL, leak level in ppm, and user adjustable alarm point.

Features

• Combustible Gas Leak Detector capable of displaying real ppm, stepped ppm, and %LEL (Lower Explosive Limit).
• 10ppm sensitivity (methane)
• Detect combustible gases including natural gas, propane, butane, etc.
• Thumbwheel adjustable tic rate to locate leaks quickly and accurately
• Two line display with bargraph and backlight
• Audio / Visual alarm indication with user adjustable alarm point
• Earphone jack for use in noisy environments
• Approximately 20 hours of continuous use (C cell alkaline batteries x2)

Applications

• Detect combustible gasses including natural gas methane, propane (LPG), gasoline, diesel, and kerosene
• Trace natural gas lines and fittings for leaks
• Check gas generation for leaks

Standard Accessories

• Carrying Pouch (A780)
• Instruction Manual
• Battery and Sensor (Installed and Calibrated)

735A Gas Leak Detector by Test Products International

Designed to quickly and accurately measure natural and propane gas leaks, as well as carbon monoxide concentrations.

Features

• Internal Pump
• Water/Dust Filter
• Push Button Operation
• Field Calibration
• Date/Time Display
• Calibration Alert
• Operation Memory
• Calibration Memory
• Infrared Download
• Audible/Visual Alarms
• Backlit LCD
• Programmable Auto Shut Off

Applications

• Gas Leak Survey/Investigations
• Confined Space Monitoring
• Gas Emergency Investigations
• Vessel Testing

Standard Accessories

• Carrying Pouch (A780)
• Instruction Manual
• Battery and Sensor (Installed and Calibrated)

737K1 Purge Probe Kit by Test Products International

Meets the requirements for latest NFPA 54 fuel gas purging requirements for large gas systems.

Measure combustible leaks, LEL and %volume

Provides personal protection from potential hazardous conditions and help find the source of combustible gases fast!

Features

• Internal Pump
• Water/Dust Filter
• Push Button Operation
• Field Calibration
• Date/Time Display
• Calibration Alert
• Operation Memory
• Calibration Memory
• Infrared Download
• Audible/Visual Alarms
• Backlit LCD
• Programmable Auto Shut Off

Applications

• Gas Leak Survey/Investigations
• Confined Space Monitoring
• Gas Emergency Investigations
• Vessel Testing

The 737K1 Purge Probe Kit includes the following:

• 737
• Carry pouch
• Instruction manual
• A758 purge probe
• Batteries
• Extra water/dirt filter trap

750A Refrigerant Leak Detector by Test Products International

The 750a features 400 hour sensor life under normal use; a spare sensor is included with each instrument for a total of 800 hours of continuous use and can detect leaks as small as 0.2 ounces per year (R134a / R22).

Whether testing for leaks in air conditioning, refrigeration, or automotive AC, the versatile 700 series spans the diverse needs of technicians, refrigeration engineers, and maintenance personnel around the globe. From freezer coils to heat pumps, experience fast, reliable results that save you both time and money.

The TPI 750a is a state-of-the-art refrigerant leak detector capable of detecting all halogen based gases. Selectable sensitivity combined with an adjustable tick rate will allow any service professional to pinpoint those tough to find leaks even in contaminated environments.

Sensor life can be extended by fitting a 1/2" long piece of vinyl tubing onto the sensor tip. This tubing helps prevent foreign material from getting into the sensor during tests; clean or replace the tube regularly.

Even though TPI refrigerant leak detector sensors are very durable and can last up to 400 hours, sensor life can be aided by press fitting a 1/2" long piece of vinyl tubing onto the sensor tip. This tubing helps prevent foreign material from getting into the sensor during tests. Clean or replace the tube regularly.

Features

• Detects all existing refrigerants and blends including 404A, PURON 410A and *R-507 (AZ50)
• 400 hour individual sensor life; a spare sensor is included with each instrument for a total of 800 hours of continuous sensor use.
• Fast response; Begin testing immediately after power on
• 0.2 ounce per year sensitivity
• One hand thumb wheel operation
• Pinpoint small leaks easily by elimination of background concentration with fully adjustable tic rate
• Visual indicators for power, tic rate and battery replacement
• Optional earphone attachment

Applications

• Check for leaks in refrigeration systems
• Test for leaks in air conditioning systems and cooling units
• Find leaks in automotive air conditioning systems

Standard Accessories

• Sensor: A712
• Instruction Manual: 750a Instruction Manual
• Soft Pouch A700

Optional Accessories

• Soft Case w/strap A755
• Earphone A710
• Test vial A713