Pelsue

1385D Axial Blower, Metal Housing, 25' Hose/Canister Attached, 1/3HP, 120 Volt AC by Pelsue

These axial "Air-Pacs" are blower, hose, and storage canister all- in-one. The models vary from 120 VAC, 60 Hz to 220 VAC, 50Hz; 15' or 25' of hose stored in canister or our special spacemaker hose. All the models are third party certified by CEESI and all are constructed to CE requirement. The light weight steel constructed blowers are powder painted and provide as much as 668 CFM.

6506A Ground Tent, Yellow and White, 6' x 6' x 6'H, with Case by Pelsue

A-Series tents make excellent general work tents. Light weight and portable, these tents are made from high quality materials. The primary fabric in these tents is a urethane coated, waterproof, mildew resistant, UV protected, flame retardant (to CPAI-84) polyester. With cast aluminum hubs and pultruded Fiberglass Rods A-Series tents are tough and will work wherever the job takes you. "A" Model Tents includes two screen windows with roll up flaps, three tie down cords through the hub, ground flaps, heavy duty frame, wide open front, dual zipper roll up door, interior and exterior roof line loops for tie down, carrying case, & three tent stakes.

2025HD 8" Diameter x 25' Heavy Duty Duct, Sleeve One End by Pelsue

Pelsue's Standard Ventilator Hoses are made to be compatible with Pelsue Blowers. Made of Polyester with a neoprene coating heat reaction (HRT), these hoses are built to last. These hoses are available both glued and sewn, in a variety of lengths, and with or without insulation. All hoses have a tension buckle and strap at one end.

PHQR-T45 45' Technora Rope and ANSI Z359 Swivel Snap Hook by Pelsue

The Pelsue PHQR Series hoist is designed to be a personnel rescue and retrieval device. The PHQR Series hoist shares many of the same qualities and capabilities as a standard PH series hoist but is unique in the fact that the lifting rope is not permanently fixed to the hoist drum. The hoist drum incorporates a rope gripping cleat into which the rescue line can be placed when a retrieval or rescue becomes necessary. This unique feature allows for extremely fast retrieval as there is no need to take up slack in the rescue line as the rope can be gripped at any location along its length. The separation of the rope from the hoist also addressees a safety concern when working in underground manhole vaults that can only be entered roadside where the potential for an out of control vehicle dragging away the retrieval system is possible.

The hoist is available in two model variations: the rope can either be loaded on the underside (Model #PHQR) or topside (Model #PHQRR) of the rope drum. The two variations of hoist have rotations the reverse of each other which in turn places the hoist handle on either the left (Model #PHQR) or right (Model #PHQRR) hand side of the hoist frame. The model #PHQR & #PHQRR do not include rope & hook assemblies, but a wide variety of sub-models are available with varying lengths of rope and differing snap hooks & end fittings. The PHQR series can coil a maximum of 70' of 1/4" synthetic rope. The use of wire rope is not possible on the PHQR series hoist. The PHQR hoist is equipped with a standard Pelsue Quick-Release bracket (#501073-001). Other adapter brackets can be supplied or added upon request.

Detailed Specifications:

Pelsue PHQR Series hoists are designed and tested as Mechanical Retrieval Devices as defined in OSHA 1910.146 & ANSI Z117.1. PHQR Series hoists are approved for use with personnel and are intended to facilitate positioning and rescue / retrieval operations when required.

Load Capacity: 310 LBS. (141 KG) *[Capacity is valid only when there are 4 complete wraps of rope on the drum]
Gear Ratio: 5 to 1

Braking Capabilities:

PHQR hoists are equipped with a long-life friction-brake system that is supplemented by a positive-locking double-pawl arrangement that completely eliminates the risk of "free-wheeling". PHQR hoists are also equipped with a centrifugal "overspeed" brake for redundancy.

Rope Assembly:

3/16" Hi Heat Synthetic "Technora" Rope: Minimum Breaking Strength 5500 LBS. (2494 KG)

Weight:

PHQR Series (70' of Synthetic Rope) 21-1/2 LBS. (9.8 KG)

Features:

• Quick-Release Bracket allows quick installation & removal from the structure
• Drum-Mounted Rope Cleat allows the separation of the rope and mechanical device during entry operations.
• Provides a simple means of lifting / lowering of personnel

6508FS Fiber Optic Splicing Tent, 8' x 8', White/Black Rear, Rear Wall Zipper Cable Slot, with Case by Pelsue

This portable tent features improvements specifically for fiber splicing. Including a large rear access slot for large truck cables. With a spacious interior there is more than enough room for your equipment and a collapsible table. The tent has two side vents, with fabric mesh screening which allows for additional ventilation and light to get in while keeping insects out. The front side of the tent also functions as a roll-up door, and includes double sided zippers to allow for easy entry and exit. Both the roll-up door and the two side vents can be secured with built in Velcro straps. The back features two locking zippers to facilitate cable and fiber access into the tent, while minimizing the unwanted light. As always the tent material is Fire/UV/Water resistant to ensure a comfortable working environment regardless of the weather, and comes with a case.

Features of the Fiber to the Home Shelter

• Large 14" cable access door, includes double-sided zipper, also suitable as a ventilation/hose pass-through.
• Solar blocking (black) Material on all interior surfaces-Heavy duty frame for increased wind resistance
• Webbing loops on all four corners, allows corners to be secured with ground stakes if necessary
• Tie down cords on both exterior sides and rear, for use with ground stakes if necessary
• Roll-up front door, with two double sided heavy-duty zippers, and tie-offs at the top of the tent to secure door when not in use
• Two oversized black mesh windows, one on each of the sides (not front or rear), for additional light and/or circulation

DK3036 Davit Mast, Includes Center Post, Elbow & 30"/36" Offset Arm (base and winch separate) by Pelsue

Pelsue offers a wide variety of Davit kits for our bases. These davits are man-rated to 350 lbs. and have a universal bracket for attachment of alternate lifting systems and/or 900 lbs maximum arresting force devices. This assembly provides locations for up to two device mounting plates. One standard Pelsue winch mounting plate is provided with the assembly. Available in assemblies and individual parts. Dimensions and specification given below.

6508DCS Ground Tent 6508D with Cable Slot in Rear Wall by Pelsue

DCS Model ground tents feature a vertical slit in the rear wall, from the hub to the ground. Slit is closed over by means of a "Velcro" style closure and a hook & ring assembly. Used to allow entry of cable or pipe when doing fusion or splicing in the tent. Includes vent sleeve.

49400M Complete MAxI Duct Rodder with Frame/Spool, 400' Marked by Pelsue

Developed for 3" (7.6 cm) or larger conduit and up to 1200 feet (366 m). The Maxi rodder combines long range lengths with high superior strength. Pulling strength is rated at 3300 lbs (1496 kg) while 24" to 30" (61 cm to 76 cm) radius bends are easily negotiated. Especially effective in pulling heavy electrical and telecommunications cable in long runs. This is a domestic rod not containing the same fiber ratio as other sizes. Complete Unit Includes: 7/16" (1.1 cm) diameter rod from 400' to 1200' (120 m to 365 m), Vertical/Horizontal stand & spool with wheeled frame & spool brakes to avoid "spring out" effect, threaded end fittings to accept all accessories, units come marked in feet (add an additional "M" to part number for meters).

6508A Ground Tent, Yellow and White, 8' x 8' x 6.5'H, with Case by Pelsue

A-Series tents make excellent general work tents. Light weight and portable, these tents are made from high quality materials. The primary fabric in these tents is a urethane coated, waterproof, mildew resistant, UV protected, flame retardant (to CPAI-84) polyester. With cast aluminum hubs and pultruded Fiberglass Rods A-Series tents are tough and will work wherever the job takes you. "A" Model Tents includes two screen windows with roll up flaps, three tie down cords through the hub, ground flaps, heavy duty frame, wide open front, dual zipper roll up door, interior and exterior roof line loops for tie down, carrying case, & three tent stakes.

6334ASB Multi-Tent - strand hardware, 3.6' W x 3.6' L x 8' H by Pelsue

The Pelsue Multi-Tent can attach to a strand, bucket, ladder, pole, or manhole guard with the appropriate hardware.

This tent is available with plastic hub (6334AP) instead of metal hub (6334A) and is also available in a larger size (6334AN).

Features:

• 5-in-1 Tent
• Solar blocking top
• Easy set-up

Includes:

• Strand Hardware (63350)
• Clips & D-rings to close off tent
• Solar blocking top
• Heavy-duty frame
• Roll-up sides
• Carrying case

Not included:

• Bucket Hardware (63360)
• Ladder/Pole Hardware (63380)
• Guard Hardware (63390)

6510A Ground Tent, Yellow and White, 10' x 10' x 6.5'H, with Case by Pelsue

A-Series tents make excellent general work tents. Light weight and portable, these tents are made from high quality materials. The primary fabric in these tents is a urethane coated, waterproof, mildew resistant, UV protected, flame retardant (to CPAI-84) polyester. With cast aluminum hubs and pultruded Fiberglass Rods A-Series tents are tough and will work wherever the job takes you. "A" Model Tents includes two screen windows with roll up flaps, three tie down cords through the hub, ground flaps, heavy duty frame, wide open front, dual zipper roll up door, interior and exterior roof line loops for tie down, carrying case, & three tent stakes.

PM-4020 Dewatering Pump, 1 HP, 120V AC, 12.4 Amp, 2" Discharge, 115 GPM, Submersible by Pelsue

Looking for submersible pumps? Try Pelsues most popular and affordable range of submersible pumps. As always Pelsue preinstalls the coupling and includes rope for raising and lowering for every pump.

9S27 Cable Clamp Option Counter Top with Suction Cups and Pump by Pelsue

This clamp is used secure the fiber optic cable while working on it in a trailer or work tent. It would be used on a trailer countertop or a folding work table while working in a splicing tent. The suction cup feature allows the user to position this clamp anywhere on a flat smooth surface to best manage the cable while sorting and splicing. This clamp provides the mobility needed that a permanently fixed clamp cannot provide.