Pelsue

PHQR-T45 45' Technora Rope and ANSI Z359 Swivel Snap Hook by Pelsue

The Pelsue PHQR Series hoist is designed to be a personnel rescue and retrieval device. The PHQR Series hoist shares many of the same qualities and capabilities as a standard PH series hoist but is unique in the fact that the lifting rope is not permanently fixed to the hoist drum. The hoist drum incorporates a rope gripping cleat into which the rescue line can be placed when a retrieval or rescue becomes necessary. This unique feature allows for extremely fast retrieval as there is no need to take up slack in the rescue line as the rope can be gripped at any location along its length. The separation of the rope from the hoist also addressees a safety concern when working in underground manhole vaults that can only be entered roadside where the potential for an out of control vehicle dragging away the retrieval system is possible.

The hoist is available in two model variations: the rope can either be loaded on the underside (Model #PHQR) or topside (Model #PHQRR) of the rope drum. The two variations of hoist have rotations the reverse of each other which in turn places the hoist handle on either the left (Model #PHQR) or right (Model #PHQRR) hand side of the hoist frame. The model #PHQR & #PHQRR do not include rope & hook assemblies, but a wide variety of sub-models are available with varying lengths of rope and differing snap hooks & end fittings. The PHQR series can coil a maximum of 70' of 1/4" synthetic rope. The use of wire rope is not possible on the PHQR series hoist. The PHQR hoist is equipped with a standard Pelsue Quick-Release bracket (#501073-001). Other adapter brackets can be supplied or added upon request.

Detailed Specifications:

Pelsue PHQR Series hoists are designed and tested as Mechanical Retrieval Devices as defined in OSHA 1910.146 & ANSI Z117.1. PHQR Series hoists are approved for use with personnel and are intended to facilitate positioning and rescue / retrieval operations when required.

Load Capacity: 310 LBS. (141 KG) *[Capacity is valid only when there are 4 complete wraps of rope on the drum]
Gear Ratio: 5 to 1

Braking Capabilities:

PHQR hoists are equipped with a long-life friction-brake system that is supplemented by a positive-locking double-pawl arrangement that completely eliminates the risk of "free-wheeling". PHQR hoists are also equipped with a centrifugal "overspeed" brake for redundancy.

Rope Assembly:

3/16" Hi Heat Synthetic "Technora" Rope: Minimum Breaking Strength 5500 LBS. (2494 KG)

Weight:

PHQR Series (70' of Synthetic Rope) 21-1/2 LBS. (9.8 KG)

Features:

• Quick-Release Bracket allows quick installation & removal from the structure
• Drum-Mounted Rope Cleat allows the separation of the rope and mechanical device during entry operations.
• Provides a simple means of lifting / lowering of personnel

1475D Axial Blower, Metal Housing, 15' Hose/Canister attached, 12 Volt DC by Pelsue

These axial "Air-Pacs" are blower, hose, and storage canister all- in-one. The models vary from 120 VAC, 60 Hz to 220 VAC, 50Hz; 15' or 25' of hose stored in canister or our special spacemaker hose. All the models are third party certified by CEESI and all are constructed to CE requirement. The light weight steel constructed blowers are powder painted and provide as much as 668 CFM.

65068A "HIGH-5" Ground Tent, 6' x 6' x 8' High, 1/2 Moon Zip Door Rear by Pelsue

Tent measures 6' x 6' x 8' high. Ideal for use over industrial tripod or davit retrieval hoists. May be used to cover pad or pole mounted cabinets or anywhere that additional height is required. Rear Access 1/2 moon style zipper door included. Door style velcro slit and 8" diameter heater/ventilator hose sleeve.

PH10C Personnel Hoist with 100' x 3/16" Stainless Steel Cable and Pelsue Davit Bracket by Pelsue

Above the fold: Pelsue PH series hoists are designed and tested as personnel hoists for single user mechanical retrieval/ systems/lifting devices as define in OSHA safety standards for use in confined space entrances and exits.

These hoists feature an internal braking system to prevent accidental line play out, as well as a backup locking pawl system to prevent "free-wheeling". Pelsue hoists also include a redundant "over- speed" brake for additional safety. As a result of these features line extension should only occur when the handle is turned counterclockwise and a force of at least 10 lbs. is applied to the line.

All hoist frames attach to a quick release bracket which can be combined with other Pelsue safety equipment. Please to reach out to a customer service representative to insure that brackets and mounting are matched to your needs. If you are looking for a hoist for use with a tripod please see our PHT series hoists.

All PH Series hoists have the following features.

• "Man Rated" to 310 lbs
• Secondary "over-speed" brake
• A 5.5:1 gear ration single speed drive
• Free-wheeling preventing continuous braking drive
• Double pawls friction brake
• Low Wear high temperature brake pads for minimal maintenance
• Anti-friction drive bearings
• Three permanent wraps of cable on the drum, assures low cable attachment loads
• Tensioning pad to prevent loosening of cable lays
• Slip clutch drive to prevent back winding of the cable drum
• Zinc plated and aluminum components, to reduce corrosion in harsh environments
• Mount for quick attachment
• Removable drive handle with speeder knob
• Covered gear teeth
• Stainless steel cable or synthetic rope compatible
• Soft-sided carry case included

PWQRR-W45 Winch - Quick Release, Reverse Rotation, Confined Space Retrieval with 45' Rope and Wichard Hook by Pelsue

The PWQR Series of hoists are designed for use lifting personnel in situations where a quick release is required. These hoists feature a quick release, which means that the rope is not used permanently affixed to the winch drum. Thanks to this feature these hoists may be used when safety considerations dictate that it's safer to not be permanently tied off. These hoists also have a backup pawl system to prevent "free-wheeling", and an internal braking system to prevent line play out. Line extension should only occur when the handle is turned in a counter-clockwise direction and a force of at least 10 lbs. is applied. OSHA compliant for confined space entry and exit.

Features

• Secondary pawl system to prevent "free-wheeling"
• Internal breaking system to prevent line play out.
• Man-rated for 310 lbs.
• Supports a maximum of 70' of rope.

49400M Complete MAxI Duct Rodder with Frame/Spool, 400' Marked by Pelsue

Developed for 3" (7.6 cm) or larger conduit and up to 1200 feet (366 m). The Maxi rodder combines long range lengths with high superior strength. Pulling strength is rated at 3300 lbs (1496 kg) while 24" to 30" (61 cm to 76 cm) radius bends are easily negotiated. Especially effective in pulling heavy electrical and telecommunications cable in long runs. This is a domestic rod not containing the same fiber ratio as other sizes. Complete Unit Includes: 7/16" (1.1 cm) diameter rod from 400' to 1200' (120 m to 365 m), Vertical/Horizontal stand & spool with wheeled frame & spool brakes to avoid "spring out" effect, threaded end fittings to accept all accessories, units come marked in feet (add an additional "M" to part number for meters).

1375D Axial Blower, Metal Housing, 15' Hose Canister Attached, 120 Volt AC by Pelsue

These axial "Air-Pacs" are blower, hose, and storage canister all- in-one. The models vary from 120 VAC, 60 Hz to 220 VAC, 50Hz; 15' or 25' of hose stored in canister or our special spacemaker hose. All the models are third party certified by CEESI and all are constructed to CE requirement. The light weight steel constructed blowers are powder painted and provide as much as 668 CFM.

1000E Hazardous Location Centrifugal Blower, Steel - 1/3HP Explosion Proof Motor, No Plug by Pelsue

The model 1000E has an explosion proof, single speed motor on a steel frame and housing, with a non sparking aluminum blower wheel. Must be user wired. This Model is CEESI Certified.

6510A Ground Tent, Yellow and White, 10' x 10' x 6.5'H, with Case by Pelsue

A-Series tents make excellent general work tents. Light weight and portable, these tents are made from high quality materials. The primary fabric in these tents is a urethane coated, waterproof, mildew resistant, UV protected, flame retardant (to CPAI-84) polyester. With cast aluminum hubs and pultruded Fiberglass Rods A-Series tents are tough and will work wherever the job takes you. "A" Model Tents includes two screen windows with roll up flaps, three tie down cords through the hub, ground flaps, heavy duty frame, wide open front, dual zipper roll up door, interior and exterior roof line loops for tie down, carrying case, & three tent stakes.

FT-C70 Fall Arrest Tower - Uni-Lite, Carbon Fiber, Up to Three Person Tie-off by Pelsue

The Uni-Lite fall arrest tower is intended to provide an elevated fall arrest anchorage for up to three persons. The system is composed of a composite tube and cast aluminum base. This makes the system very lightweight and portable. With a variety of permanent and temporary mounting options available the FT-C70 provides excellent fall protection in tough to reach places, such as the tops of electrical transformers.

Features

• 3 point anchorage
• 360° swivel tie off
• May be used with an adjustable anchor clamp

491000M Complete MAxI Duct Rodder with Frame/Spool, 1000' Marked by Pelsue

Developed for 3" (7.6 cm) or larger conduit and up to 1200 feet (366 m). The Maxi rodder combines long range lengths with high superior strength. Pulling strength is rated at 3300 lbs (1496 kg) while 24" to 30" (61 cm to 76 cm) radius bends are easily negotiated. Especially effective in pulling heavy electrical and telecommunications cable in long runs. This is a domestic rod not containing the same fiber ratio as other sizes. Complete Unit Includes: 7/16" (1.1 cm) diameter rod from 400' to 1200' (120 m to 365 m), Vertical/Horizontal stand & spool with wheeled frame & spool brakes to avoid "spring out" effect, threaded end fittings to accept all accessories, units come marked in feet (add an additional "M" to part number for meters).

6506FSGH Fiber Optic Splicing Tent, 6 x 6', White/Black Rear, Rear Wall Zipper Cable Slot, with Case by Pelsue

This portable tent features improvements specifically for fiber splicing. Including a large rear access slot for large truck cables. With a spacious interior there is more than enough room for your equipment and a collapsible table. The tent has two side vents, with fabric mesh screening which allows for additional ventilation and light to get in while keeping insects out. The front side of the tent also functions as a roll-up door, and includes double sided zippers to allow for easy entry and exit. Both the roll-up door and the two side vents can be secured with built in Velcro straps. The back features two locking zippers to facilitate cable and fiber access into the tent, while minimizing the unwanted light. As always the tent material is Fire/UV/Water resistant to ensure a comfortable working environment regardless of the weather, and comes with a case.

Features of the Fiber to the Home Shelter

• Large 14" cable access door, includes double-sided zipper, also suitable as a ventilation/hose pass-through.
• Solar blocking (black) Material on all interior surfaces-Heavy duty frame for increased wind resistance
• Webbing loops on all four corners, allows corners to be secured with ground stakes if necessary
• Tie down cords on both exterior sides and rear, for use with ground stakes if necessary
• Roll-up front door, with two double sided heavy-duty zippers, and tie-offs at the top of the tent to secure door when not in use
• Two oversized black mesh windows, one on each of the sides (not front or rear), for additional light and/or circulation

6508D Ground Tent, Yellow and White, 8' x 8' x 6.5'H, with Case by Pelsue

D-Series tents are highly durable and portable general purpose work tents. Most importantly they feature inter-connectable flaps that allow two tents to be attached together, once attached entrance can be gained through the flaps. D-Series tents may be combined with DRAD tents which feature a rear access door if desired. This makes D-Series tents perfect for situation where you want separate but connected work-spaces. As with all Pelsue tents the primary fabric is water, mildew, UV, and flame retardant (to CPAI-84).

Includes:

• One-piece, instant set up
• No loose parts
• Two screened windows (most models)
• Tie-down cords through hubs
• Ground flaps for weight anchoring
• Rubber, non-slip feet
• Exterior, roof level D-rings
• Carry case & three tent stakes
• Heavy duty frame
• Wide open front
• Snap and D-rings with interconnecting flaps (connects 2 tents together)
• Ventilation hose entry sleeve
• Interior and exterior roof line loops for tie down
• Tent Stabilizing Feet (6510C only)

9S27 Cable Clamp Option Counter Top with Suction Cups and Pump by Pelsue

This clamp is used secure the fiber optic cable while working on it in a trailer or work tent. It would be used on a trailer countertop or a folding work table while working in a splicing tent. The suction cup feature allows the user to position this clamp anywhere on a flat smooth surface to best manage the cable while sorting and splicing. This clamp provides the mobility needed that a permanently fixed clamp cannot provide.

PF10CCE-1 Dewatering Pump, 5 HP, 230VAC, 1 PH, 2" Discharge, Centrifugal by Pelsue

ALL Centrifugal pumps come equipped with couplers, needs to be wired for power & permanetly mounted to a solid structure.

1325P Axial Blower, Plastic Housing, 1/3HP, 120 Volt AC by Pelsue

The Model 1325P 120 VAC, electric blower is constructed of a durable, weather resistant, high-impact polyethylene plastic. The CSA and CEESI certified unit will accept any 8" blower duct or our model AIRPAC series. The unit also comes in 12 VDC (model 1400P). Weighing only 15 lbs, the units provide as much as 921 CFM. This Model is CSA, CEESI Certified.

1453 Centrifugal Blower, Honda Engine, 4 HP by Pelsue

The models 1450 and 1453 provides total portability in a high volume blower. Compact and light weight, these blowers are dampened against excessive vibration. The model 1450 uses a Briggs & Stratton engine. Model 1453 uses a Honda Motor. These models are CEESI Certified.

6508DRADSB Dual-Entry Series - roll-up rear access door, 8' W x 8' L x 6.5' H by Pelsue

The Pelsue Dual-Entry Series improves upon the Interlocking Series by adding a rear-access door for easy entry and exit when the front of the tent is closed off. This allows for greater access to work on a cabinet/box when two tents are connected together, or when the tent is attached to a work vehicle.

• Rear-access Door
• Easy Set Up
• Interlocking Doors
• Clips and D-rings with interlocking flaps
• 30" wide dual zipper roll-up rear-access door
• Heavy-duty frame
• Roll-up front flaps
• 8" side ventilation hose entry sleeve
• 2 screen windows with roll-up flaps
• 3 tie-down cords through the hubs
• 7 stakes and 4 ground loops
• Carrying case

6508DRAD Ground Tent 6508D with Roll Up Rear Access Door by Pelsue

DRAD tents incorporate the standard features found in the Pelsue "D" series ground tents, along with a 30" wide roll-up rear door for personnel entry and exit. It is ideal for working up against any type of cabinet. The tent also doubles as a standalone ground tent for construction or splicing.

Also can be used in conjunction with same size D series tent.

1385D Axial Blower, Metal Housing, 25' Hose/Canister Attached, 1/3HP, 120 Volt AC by Pelsue

These axial "Air-Pacs" are blower, hose, and storage canister all- in-one. The models vary from 120 VAC, 60 Hz to 220 VAC, 50Hz; 15' or 25' of hose stored in canister or our special spacemaker hose. All the models are third party certified by CEESI and all are constructed to CE requirement. The light weight steel constructed blowers are powder painted and provide as much as 668 CFM.