Jenco

9251NKA D.O. & Temperature Handheld Polarographic Meter Kit by Jenco

Includes:

• 9251N D.O. & Temperature Handheld Polarographic Meter
• LD-900-8-DO Stainless Steel Field Probe with 8-Pin Connector 8-Pin Connector & 10-ft Cable
• LD-900-03A Membrane Kit with 6 Caps & KCL Solution

• Clear LCD displays dissolved oxygen as percent air saturation or as parts per thousand simultaneously with temperature.
• Convenient one point calibration for dissolved oxygen. Calibration data is stored in memory and is ready for use on power up.
• User selectable salinity and pressure compensated dissolved oxygen readings.
• Work with accurate and reliable polarographic dissolved oxygen probes.
• Inclined back provides ideal viewing angle for benchtop use.
• 50 memory storage of dissolved oxygen with temperature reading with memory location ID.
• RS-232 computer interface with software.
• IP65 waterproof.
• AC adaptor or battery power (low battery indicator).

103 Handheld Conductivity Meter with LCD Display by Jenco

Conductivity handheld meter with LCD display, rugged splash proof case and replaceable K-1.0 conductivity probe. Has cell adjust and automatic temperature compensation from 5 to 55°C. Uses one 9 volt battery, 50 hours typical usage on one battery.

• LCD display
• Conductivity cell adjust
• High stability
• Rugged case
• CEll constant k = 1.0

765TC Thermocouple Panel Thermometer, Type T, Range -105 to 400 °C by Jenco

Panel mount digital thermometer with analog voltage output of 1 mV per digit, with analog output accuracy of ± 0.2%, features a bright red LED display and 1/8 DIN plastic housing. °C/°F selectable via plastic jumper behind front bezel. Available in types. J, K, T, E, and 3-wire Pt-100 RTD. Ambient range 0 to 60°C. 115/230V AC operation.

• High accuracy
• 50/60 hz rejection design
• Compact 1/8 DIN plastic case
• °C/°F selectable w/ re-calibration
• Models available for k,j,t,e pt-100
• Upscale break detection
• Cold junction consumption design
• 1mv/digit analog output
• Easy to install
• 0.56 high efficiency ide display

765EC Thermocouple Panel Thermometer, Type E, Range -105 to 1000 °C by Jenco

Panel mount digital thermometer with analog voltage output of 1 mV per digit, with analog output accuracy of ± 0.2%, features a bright red LED display and 1/8 DIN plastic housing. °C/°F selectable via plastic jumper behind front bezel. Available in types. J, K, T, E, and 3-wire Pt-100 RTD. Ambient range 0 to 60°C. 115/230V AC operation.

• High accuracy
• 50/60 hz rejection design
• Compact 1/8 DIN plastic case
• °C/°F selectable w/ re-calibration
• Models available for k,j,t,e pt-100
• Upscale break detection
• Cold junction consumption design
• 1mv/digit analog output
• Easy to install
• 0.56 high efficiency ide display

6219KB Digital pH/mV/Ion/Temp Meter Kit by Jenco

Includes:

• 6219 Digital pH/mV/ION/TEMP Meter
• 6005C Cable
• 6230D115 AC Adapter

• Two LCD display pH, mV, direct ion concentration and temperature.
• Convenient calibration with automatic buffer recognition of US or European pH buffer sets. Quick two points ion calibration. Calibration data is stored in memory and is ready for use on power up.
• User selectable resolution of up to 0.001 for greatest accuracy.
• Direct read out in ion concentration to simplify ion measurements.
• RS-232 computer interface with software.
• AC adaptor or battery power (low battery indicator).

378JC Digital Thermometer Controller with Analog Voltage Output, Range 0 to 550 °C by Jenco

Panel mount digital thermometer controller with analog voltage output of 1 mV per count, ± 3%, bright red LED display, 1/8 DIN plastic housing, hysteresis is ± 3°C or ± 5°F. Proportional Band-Width control from 5%, 378KF, 10% 378 KC/JF and 20% of span for 378 JC. Features manual adjust reset. Cycle time is 20 seconds ± 3 seconds. 115/230V AC operation.

3010M+106A Handheld Cond/TDS/Sal/Temp Meter Kit by Jenco

Includes:

• 3010M Handheld Cond/TDS/Sal/Temp Meter
• 106A Two-wire conductivity cell with 4 PIN connector, K=1.0 (0.02~20.00mS/cm).

• Simultaneous displays of conductivity, salinity or TDS with temperature measurements.
• 50 data set reviewable memory.
• Convenient one point calibration. Calibration data is stored in memory and ready for use on power up.
• Selectable cell constants for true wide range readings.
• Adjustable TDS coefficient, reference temperature and temperature coefficient.
• Uses one conductivity cell for conductivity, salinity and TDS measurements.
• Accepts 2-wire conductivity cells with K=0.1, 1.0 and 10.0 cell constants for improved flexibility and accuracy.
• Automatic shutoff function (30 minutes of non-use).
• Battery life over 1000 hours.
• IP65 waterproof.
• Low battery indicator.
• RoHS and CE compliant.

6350MKC pH/Conductivity/Salinity/mV/Temp. Handheld Meter with RS-232 & Memory Kit by Jenco

The Jenco 6350 is a high performance pH/Conductivity/Salinity/mV/Temp. handheld meter in a splash proof case with an RS-232C interface that allows it to communicate with any IBM compatible PC. This meter is CE approved and features 0.01 pH Resolution and a mV range of ± Salinity is in the range of 0.0 to 80.0 ppt with a 0.0 ppt resolution. Conductivity Cells are selectable for K=1.0 or K=5.0 and ranges are selectable for uS or mS.

Includes:

• 6350M pH/Conductivity/Salinity/mV/Temp. Handheld Meter with RS-232 & Memory
• 600P pH/ref eledtrode
• model 101 K=1.0 cond. cell
• 6230D115 AC Adapter
• 6350F carrying case

• pH buffer recognition: model 6350 (pH:7.00,4.01,10.01) , model 6350c (pH:6.86,4,9.18)
• Selectable 2/4 wire cells for long cable length & wide measurement range
• Store 50 sets of data in non-volatile memory
• Conductivity auto/manual range
• Power down memory backup
• Splash resistant/watertight case
• Audio feedback keys
• Battery/ac adaptor
• RS-232c output

60K pH Meter Kit by Jenco

pH handheld meter with BNC, LCD display and manual temperature compensation with two point calibration via potentiometers for ease of use. Case is rugged and splash resistant. AC/DC Powered.

Includes:

• 60K pH Handheld Meter
• 600P pH electrode
• 600D115 AC adapter
• 6007F carrying case

• All solid state design
• High accuracy
• LCD display
• Extra long battery life
• Battery low indicator
• Low cost
• Rugged carrying case
• Power: one 9V DC battery or 115/230v ac adapter

791LKF Panel Mount Digital Temperature Transmitter with 4- 20 mA Current Output, Type K, Red LED by Jenco

Panel mount digital temperature transmitter with 4- 20 mA current output that allows the 791 to drive any loop powered process indicator or recorder. Current output has expanded or normal switch for user adjustable center point and span control for temperature to 4-20 mA output and features a LCD display & 1/8 DIN Aluminum case. Types. J, K, T, 3-wire Pt-100 RTD, specify °C or °F. Ambient range 0 to 40°C. 115 / 230V AC operation.

• All solid state design
• Low power consumption ,reduced internal heating ,increased reliability
• High 50/60 hz noise rejection
• Heat cycled 100 hours before shipment
• Available for various thermocouple and rtd calibrations
• Easy to install
• Aluminum 1/8 DIN housing
• Isolated 4 to 20 mA output over span in nor mode
• 115VAC /230VAC operations

3173 Large LCD Conductivity/TDS/Temperature Benchtop Meter by Jenco

Conductivity/TDS/Temperature benchtop meter, with an extra large LCD display, adjustable cell constants K=0.1, 1.0, 10.0, programmable temperature co-efficient and reference temperature. Battery or 115/230 AC powered. CE approved.

• Clear, large LCD display (4 1/8 x 3 1/16 in.).
• Displays conductivity and temperature, or tds and temperature readings at the same time.
• Accepts 2-wire conductivity cells with adjustable k=0.1, k=1 and k=10 cell constants for improved flexibility and accuracy.
• Auto or manual ranging of 3 conductivity ranges are available for improved usability.
• Convenient one point calibration. calibration data is stored in memory and is ready for use on power up.
• Readings are automatically compensated for temperature (ATC). meter automatically switches into manual
• compensation when temperature probe is not present.
• Automatic lock mode is available to lock in stable readings.
• Intuitive operation with membrane keypad with tactile and audio feedback.
• Splash resistant case is made with durable, reinforced plastic for added protection. protective covers for connectors are included.
• Large LCD is offset for improved protection against unintentional damage.
• Smaller case does not clutter valuable desk space.
• 8pin DIN connector for conductivity cell & 10k thermistor.
• AC adaptor or battery power.

791LPTBF Panel Mount Digital Temperature Transmitter with 4- 20 mA Current Output, Type PTB, Red LED by Jenco

Panel mount digital temperature transmitter with 4- 20 mA current output that allows the 791 to drive any loop powered process indicator or recorder. Current output has expanded or normal switch for user adjustable center point and span control for temperature to 4-20 mA output and features a LCD display & 1/8 DIN Aluminum case. Types. J, K, T, 3-wire Pt-100 RTD, specify °C or °F. Ambient range 0 to 40°C. 115 / 230V AC operation.

• All solid state design
• Low power consumption ,reduced internal heating ,increased reliability
• High 50/60 hz noise rejection
• Heat cycled 100 hours before shipment
• Available for various thermocouple and rtd calibrations
• Easy to install
• Aluminum 1/8 DIN housing
• Isolated 4 to 20 mA output over span in nor mode
• 115VAC /230VAC operations

5005 pH/mV/Temp. Handheld Meter by Jenco

pH/mV/Temp. handheld meter with build in tabletop stand with LCD digital display. Meter has both ATC and manual temperature compensation. pH standardization calibration is via knobs and pH slope calibration is via potentiometer. Features include a voltage recorder output, reference input pin and BNC input connector. AC/DC Powered.

• All solid state design
• Fast input response
• Low drift and high stability
• Tilt stand
• Greater than 100db 50/60hz rejection
• Battery low indicator
• Extra long battery life
• Auto polarity mv measurement
• Analog recorder output
• Rugged carrying case
• UL approved ac line adaptor
• Aconventional 9v battery
• Manual and ATC for pH measurement
• 0 to 100.0 °C range of temperature measurement
• 0.5 high liquid crystal display readable under bright ambient conditions

3173K1 Large LCD Conductivity/TDS/Temperature Benchtop Meter Kit by Jenco

Conductivity/TDS/Temperature benchtop meter, with an extra large LCD display, adjustable cell constants K=0.1, 1.0, 10.0, programmable temperature co-efficient and reference temperature. Battery or 115/230 AC powered. CE approved.

Includes:

• 3173: Benchtop Conductivity meter
• Choice of 101: Epoxy, Conductovity probe, K=1.0, 3-ft or 106: Glass, Conductivity probe, K=1.0, 3-ft
• Choice of 6230D115: 120V AC adapter or 6230D230: 220V AC adapter

• Clear, large LCD display (4 1/8 x 3 1/16 in.).
• Displays conductivity and temperature, or tds and temperature readings at the same time.
• Accepts 2-wire conductivity cells with adjustable k=0.1, k=1 and k=10 cell constants for improved flexibility and accuracy.
• Auto or manual ranging of 3 conductivity ranges are available for improved usability.
• Convenient one point calibration. calibration data is stored in memory and is ready for use on power up.
• Readings are automatically compensated for temperature (ATC). meter automatically switches into manual
• compensation when temperature probe is not present.
• Automatic lock mode is available to lock in stable readings.
• Intuitive operation with membrane keypad with tactile and audio feedback.
• Splash resistant case is made with durable, reinforced plastic for added protection. protective covers for connectors are included.
• Large LCD is offset for improved protection against unintentional damage.
• Smaller case does not clutter valuable desk space.
• 8pin DIN connector for conductivity cell & 10k thermistor.
• AC adaptor or battery power.