Jenco

6010N Handheld pH/ORP Meter by Jenco

• Simultaneous displays pH or mV and temperature.
• 50 data set reviewable memory (6010M only).
• Convenient calibration with automatic buffer recognition of US and European buffer sets. Calibration data is stored in memory and ready for use on power up.
• Automatic or manual temperature compensation.
• Automatic lock mode and end point sensing are available to lock in stable readings.
• Automatic shutoff function (30 minutes of non-use).
• Battery life over 1000 hours.
• IP65 waterproof
• Low battery indicator.
• RoHS and CE compliant.

628NF ORP/Temperature VisionPlus Pen with Memory & Replaceable ORP Electrode by Jenco

VisionPlus ORP628N is a very powerful ORP tester with temperature readout, IP67 rated body, 50 memory storage and replaceable ORP electrode module.

• Clear graphic LCD displays ORP and temperature at the same time
• Replaceable electrode module ensures extended usefulness
• IP67 water-proof, dust-proof body
• Battery life over 300 hours
• 50 memory storage of both ORP and temperature readings with memory location ID and date and time stamp
• Low battery indicator
• RoHS compliant

791LPTAC Panel Mount Digital Temperature Transmitter with 4- 20 mA Current Output, Type PTA, Red LED by Jenco

Panel mount digital temperature transmitter with 4- 20 mA current output that allows the 791 to drive any loop powered process indicator or recorder. Current output has expanded or normal switch for user adjustable center point and span control for temperature to 4-20 mA output and features a LCD display & 1/8 DIN Aluminum case. Types. J, K, T, 3-wire Pt-100 RTD, specify °C or °F. Ambient range 0 to 40°C. 115 / 230V AC operation.

• All solid state design
• Low power consumption ,reduced internal heating ,increased reliability
• High 50/60 hz noise rejection
• Heat cycled 100 hours before shipment
• Available for various thermocouple and rtd calibrations
• Easy to install
• Aluminum 1/8 DIN housing
• Isolated 4 to 20 mA output over span in nor mode
• 115VAC /230VAC operations

112 Conductivity Pocket Pen Style Tester (1 to 199 uS/cm) by Jenco

Conductivity pocket pen style tester, automatic temperature compensation from 5 to 55°C, with calibration via trimmer. Power 4 x 1.5 V batteries, 200 hours typical.

• Auto temp. compensation

692 1/8 DIN Panel Mount pH Transmitter with 4-20 mA Output by Jenco

1/8 DIN panel mount pH transmitter with 4-20 mA output and calibration by potentiometers. ATC temperature control uses a Pt-100 or simulation resistor. Features a large LCD display and uses a BNC input and spade lug screw type connector block.

• All solid state design
• ATC
• Low power consumption design, reduced internal heating thus increased reliability
• 0.56 high LCD display
• Isolated 4 to 20 mA current output
• High stability and fast response
• 1/8 DIN standard aluminum case
• Easy to install
• Heat cycled 100 hours before shipment

6173KBA Benchtop pH/mV/Temperature Meter Kit by Jenco

pH/mV/Temp benchtop meter with an extra large LCD display for ease of use. Features a splash proof and rugged case ideal for schools and universities. Features EEF, Electrode Efficiency Function, multiple buffers 4.00, 4.01, 6.86, 7.00, 9.18 & 10.0 and automatic slope, buffer and electrode offset recognition. Has power down memory backup and works on 6 AA batteries or 115/230 V AC adapters. CE Approved & ISO 9001 Certified.

Includes:

• 6173 Benchtop pH/mV/Temperature Meter
• 6000P pH/Ref./Temp. Probe
• 6005C Cable
• 6230D115 AC Adapter
• Electrode Holder Arm

• Larger LCD display
• Buffers recognition
• Electrode offset recognition
• Electrode slope recognition
• Built in buffer temp. coefficient
• Auto lock
• Touch keys with audio feedback
• Power down memory
• Battery/ac adaptor
• Low power consumption
• Battery low indicator
• Percentage of power supply display

6230NKD Accessories Kit for 6230N Meter by Jenco

Includes:

• 6230F Case
• 6230D115 AC Adapter
• Buffers & Bottles

3676 1/4 DIN Panel Mount pH/ORP Controller/Transmitter by Jenco

1/4 DIN panel mount pH/ORP controller/transmitter with dual SPDT Hi/Lo relays, manual set points and calibration are via potentiometers. Features a 4-20 mA current output and has an external pH/ORP select switch. Display is a large bright red LED display. Connectors are a BNC input and spade lug screw type connector blocks. Meter requires a Pt-100 ATC or temp. simulation resistor. Power 115/230V AC.

• Isolated 4 to 20 mA output
• Dual on/off relays
• Large led display
• ATC
• 115VAC /230VAC operations
• Compact 1/4 DIN case
• Low power solid state design
• Front panel output current span adjustable control
• Front panel acid/base influent select switch
• Front panel high/low relay format select switch

609 pH Handheld Meter by Jenco

pH handheld meter with LCD digital display and manual temperature compensation. pH calibration is via knobs and pH slope calibration potentiometer. Meter has voltage recorder output and BNC connector. AC/DC Powered.

• Three position rocker switch for on/off/momentary operation
• All solid design
• Low input response
• Large energy efficient led display
• Manual temp. compensation for pH measurement
• 6conventional aabatteries
• Low drift and high stability
• UL approved ac line adaptor
• Low cost
• Rugged carrying case
• Analog recorder output

EC331 VisionPlus Resistivity/Conductivity Meter by Jenco

Jenco EC331 is an easy to use, IP67 rated conductivity tester with resistivity and temperature readout. Key features include dual display of conductivity or resistivity with temperature, selectable or auto ranging, replaceable conductivity cell and IP67 rated body.

This tester is RoHS compliant.

• Simultaneous display of conductivity and temperature, or resistivity and temperature
• Convenient 1 point calibration
• Automatic temperature compensation
• Selectable or auto ranging of conductivity and resistivity readings
• Replaceable stainless steel conductivity cell ensures extended usefulness
• 4 selectable units of measure (uS/cm, M?, °C, °F)
• Battery life of over 100 hours
• Data hold

791JF Panel Mount Digital Temperature Transmitter with 4- 20 mA Current Output, Type J by Jenco

Panel mount digital temperature transmitter with 4- 20 mA current output that allows the 791 to drive any loop powered process indicator or recorder. Current output has expanded or normal switch for user adjustable center point and span control for temperature to 4-20 mA output and features a LCD display & 1/8 DIN Aluminum case. Types. J, K, T, 3-wire Pt-100 RTD, specify °C or °F. Ambient range 0 to 40°C. 115 / 230V AC operation.

• All solid state design
• Low power consumption ,reduced internal heating ,increased reliability
• High 50/60 hz noise rejection
• Heat cycled 100 hours before shipment
• Available for various thermocouple and rtd calibrations
• Easy to install
• Aluminum 1/8 DIN housing
• Isolated 4 to 20 mA output over span in nor mode
• 115VAC /230VAC operations

791LJF Panel Mount Digital Temperature Transmitter with 4- 20 mA Current Output, Type J, Red LED by Jenco

Panel mount digital temperature transmitter with 4- 20 mA current output that allows the 791 to drive any loop powered process indicator or recorder. Current output has expanded or normal switch for user adjustable center point and span control for temperature to 4-20 mA output and features a LCD display & 1/8 DIN Aluminum case. Types. J, K, T, 3-wire Pt-100 RTD, specify °C or °F. Ambient range 0 to 40°C. 115 / 230V AC operation.

• All solid state design
• Low power consumption ,reduced internal heating ,increased reliability
• High 50/60 hz noise rejection
• Heat cycled 100 hours before shipment
• Available for various thermocouple and rtd calibrations
• Easy to install
• Aluminum 1/8 DIN housing
• Isolated 4 to 20 mA output over span in nor mode
• 115VAC /230VAC operations

791LPTAF Panel Mount Digital Temperature Transmitter with 4- 20 mA Current Output, Type PTA, Red LED by Jenco

Panel mount digital temperature transmitter with 4- 20 mA current output that allows the 791 to drive any loop powered process indicator or recorder. Current output has expanded or normal switch for user adjustable center point and span control for temperature to 4-20 mA output and features a LCD display & 1/8 DIN Aluminum case. Types. J, K, T, 3-wire Pt-100 RTD, specify °C or °F. Ambient range 0 to 40°C. 115 / 230V AC operation.

• All solid state design
• Low power consumption ,reduced internal heating ,increased reliability
• High 50/60 hz noise rejection
• Heat cycled 100 hours before shipment
• Available for various thermocouple and rtd calibrations
• Easy to install
• Aluminum 1/8 DIN housing
• Isolated 4 to 20 mA output over span in nor mode
• 115VAC /230VAC operations

3010M Handheld Cond/TDS/Sal/Temp Meter with Memories by Jenco

• Simultaneous displays of conductivity, salinity or TDS with temperature measurements.
• 50 data set reviewable memory.
• Convenient one point calibration. Calibration data is stored in memory and ready for use on power up.
• Selectable cell constants for true wide range readings.
• Adjustable TDS coefficient, reference temperature and temperature coefficient.
• Uses one conductivity cell for conductivity, salinity and TDS measurements.
• Accepts 2-wire conductivity cells with K=0.1, 1.0 and 10.0 cell constants for improved flexibility and accuracy.
• Automatic shutoff function (30 minutes of non-use).
• Battery life over 1000 hours.
• IP65 waterproof.
• Low battery indicator.
• RoHS and CE compliant.

6303C-pH Programmable Transmitter/Controller, LCD Display, 1/4 DIN by Jenco

The model 6303 is a precise instrument for the measurement and control of pH. It can also be used to measure but not control temperature and mV. A built-in micro- controller stores, calculates and compensates for all the parameters relating to pH determinations, such as the temperature characteristics of the pH electrode, pH electrode offset voltage and pH electrode slope deviations, etc.

791KC Panel Mount Digital Temperature Transmitter with 4- 20 mA Current Output, Type K by Jenco

Panel mount digital temperature transmitter with 4- 20 mA current output that allows the 791 to drive any loop powered process indicator or recorder. Current output has expanded or normal switch for user adjustable center point and span control for temperature to 4-20 mA output and features a LCD display & 1/8 DIN Aluminum case. Types. J, K, T, 3-wire Pt-100 RTD, specify °C or °F. Ambient range 0 to 40°C. 115 / 230V AC operation.

• All solid state design
• Low power consumption ,reduced internal heating ,increased reliability
• High 50/60 hz noise rejection
• Heat cycled 100 hours before shipment
• Available for various thermocouple and rtd calibrations
• Easy to install
• Aluminum 1/8 DIN housing
• Isolated 4 to 20 mA output over span in nor mode
• 115VAC /230VAC operations