Test Products International

323 Calibratable Water Resistant Digital Pocket Thermometer with Chisel Tip by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Field calibrateable to ±2°F
• Easy-to-read LCD
• Data Hold for hard to reach areas
• Penetration tip
• Auto off
• 3.1 mm stem for fast response
• 4.9 inch stem for insertion in liquids and semi-solids
• IP Rating IP67
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

716N New Combustion Analyzer with Graphical Display and Combustible Gas Leak Check Wand and NOX by Test Products International

The TPI Model 716N Flue Gas Analyzer is a state of the art, easy to use analyzer designed not only to display and calculate the required readings from a flue but also to cover most of the other measurements associated with combustion.

Features

Using TPI analyzers to determine combustion efficiency at the time of equipment set up minimizes call backs and can be used to verify to the home owner the value of service work by showing the increase in equipment efficiency after work is performed. Efficiency calculation can also be used to generate business by demonstrating the need to improve the efficiency of equipment or to show the benefit of purchasing new equipment with higher efficiency.

• Built-in differential manometer with 0.001" H2O resolution
• Measure NO (Nitric Oxide), Calculate NOX
• Calculates combustion efficiency
• Data Logging with time and date stamp
• Will not shut off if 15 ppm CO is present for increased safety
• Communicate to a PC via the USB interface
• Optional A740 IR printer available for hard copies of test results
• Built-in differential thermometer
• Store function to save up to 10 readings
• Pump driven for fast response
• Push on fittings for fast and easy use
• Large easy to read backlit display
• Ten selectable fuels
• Optional Bluetooth interface

Applications

• Tuning of residential and furnaces and domestic boilers
• Ambient and stack testing for CO
• CO safety measurements in and around combustion sources
• Temperature checking, including superheat and hydronic differential temperatures
• Dual input differential manometer with 3 selectable units of measure: kPa, mBar, inH20

Quick And Simple Set Up

All TPI analyzers feature quick and simple set up. Fast purge and the ability to perform fuel selectionduring start up enable tests to be performed quickly without requiring extra set-up time after initial startup. TPI analyzers also use the last selected fuel as the default setting. This feature prevents the need toperform fuel selection every time the analyzer is turned on.

The TPI 716N Flue Gas Analyzer comes complete with the following standard accessories:

• TPI 716N Analyzer
• Combustible Gase Leak Probe (A806)
• Rubber Boot (A765) 1 each installed on analyzer
• Soft Carrying Case (A768) - 1 each
• Flue Sampling Probe (A770) - 1 each
• In-Line Filter / Water Trap installed on Flue probe (A795) - 1 each
• Disc water filter installed in water trap (A794W) - 1 each
• Spare In-Line Filter - 1 each (A794F is a package of 5 filters)
• Temperature Probe (GK11M) - 1 each
• Battery Charger (A766) - 1 each
• Mini Pump Protection Filter Assembly (A763) - 1 each
• Exhaust Spigot Removable (A764) - 1 each
• Pressure Tubing (A774) - 1 each 6 piece
• Static Pressure Tips (A776) - 2 each
• 1/4" barbed to 1/8" NPT fitting (A603) - 2 each
• Gas Valve Adapter (A611) - 1 each
• Adapter Tubing (A791) - 1 each 4" piece
• Instruction Manual

The TPI 716 Flue Gas Analyzer has the following options available:

• A807 PC Software and cable for communication to a PC.
• A740 infrared printer (Included with 716A740)

712 Deluxe Combustion Efficiency Analyzer with Optional PC Interface by Test Products International

The carbon monoxide sensor used in TPI combustion efficiency analyzers feature an on-board filter capable of filtering NO (nitric oxide), NO₂ (nitrogen dioxide) and NOX (combination of NO and NO₂) to prevent cross sensitivity errors.

Use TPI analyzers to test flue gases in gas and oil fired equipment including high efficiency furnaces and condensing boilers. Measure CO, O₂, and stack temperature.

Determine combustion efficiency, CO₂, and CO air free. Built-in differential manometer, combustible gas detection, PC communication, and data logging.

Features

Using TPI analyzers to determine combustion efficiency at the time of equipment set up minimizes call backs and can be used to verify to the home owner the value of service work by showing the increase in equipment efficiency after work is performed. Efficiency calculation can also be used to generate business by demonstrating the need to improve the efficiency of equipment or to show the benefit of purchasing new equipment with higher efficiency.

Quick And Simple Set Up

All TPI analyzers feature quick and simple set up. Fast purge and the ability to perform fuel selectionduring start up enable tests to be performed quickly without requiring extra set-up time after initial startup. TPI analyzers also use the last selected fuel as the default setting. This feature prevents the need toperform fuel selection every time the analyzer is turned on.

• High resolution 0.001 in H20 differential manometer for high efficiency and oil equipment
• Measure CO, and temperature
• Calculate CO2, efficiency, excess air, and CO air free
• Pump driven for fast response
• Will not shut off if 15 ppm CO is present for increased safety
• Ten selectable fuels: Natural Gas, LPG, Light Oil, Heavy Oil, Bituminous Coal, Anthracite Coal, Coke, Butane, Wood, Bagasse
• Optional A740 IR printer available for hard copies of test results
• Built-in differential thermometer
• Store function to save up to 50 readings
• Large easy to read backlit display
• Rechargeable Ni-MH Battery with > 6 Hours battery life
• Optional Bluetooth interface
• Checks combustibles in flue, optional PC interface

Applications

• Tuning of residential and furnaces and domestic boilers
• Ambient and stack testing for CO
• CO safety measurements in and around combustion sources
• Temperature checking, including superheat and hydronic differential temperatures
• Detecting gas leak in gas lines and around gas fueled appliances. Dual input differential manometer with 3 selectable units of measure: kPa, mBar,inH20

329 Calibratable Water Resistant Digital Pocket Thermometer with Contact Tip (No Sheath) by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Field calibrateable to ±2°F
• Easy-to-read LCD
• Data Hold for hard to reach areas
• Penetration tip
• Auto off
• 3.1 mm stem for fast response
• 4.9 inch stem for insertion in liquids and semi-solids
• IP Rating IP67
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

709R Combustion Efficiency Analyzer with Differential Manometer by Test Products International

The carbon monoxide sensor used in TPI combustion efficiency analyzers feature an on-board filter capable of filtering NO (nitric oxide), NO₂ (nitrogen dioxide) and NOX (combination of NO and NO₂) to prevent cross sensitivity errors.

Use TPI analyzers to test flue gases in gas and oil fired equipment including high efficiency furnaces and condensing boilers. Measure CO, O₂, and stack temperature.

Determine combustion efficiency, CO₂, and CO air free. Built-in differential manometer, combustible gas detection, PC communication, data logging, and can measure NO / NOX.

Features

Using TPI analyzers to determine combustion efficiency at the time of equipment set up minimizes call backs and can be used to verify to the home owner the value of service work by showing the increase in equipment efficiency after work is performed. Efficiency calculation can also be used to generate business by demonstrating the need to improve the efficiency of equipment or to show the benefit of purchasing new equipment with higher efficiency.

Quick And Simple Set Up

All TPI analyzers feature quick and simple set up. Fast purge and the ability to perform fuel selection during start up enable tests to be performed quickly without requiring extra set-up time after initial startup. TPI analyzers also use the last selected fuel as the default setting. This feature prevents the need to perform fuel selection every time the analyzer is turned on.

• High resolution 0.001 in H20 differential manometer for high efficiency and oil equipment
• Measure CO, and temperature
• Calculate CO2, efficiency, excess air, and CO air free
• Pump driven for fast response
• Will not shut off if 15 ppm CO is present for increased safety
• Ten selectable fuels: Natural Gas, LPG, Light Oil, Heavy Oil, Bituminous Coal, Anthracite Coal, Coke, Butane, Wood, Bagasse
• Optional A740 IR printer available for hard copies of test results
• Built-in differential thermometer
• Store function to save up to 50 readings
• Large easy to read backlit display
• Rechargeable Ni-MH Battery with > 6 Hours battery life

Applications

• Tuning of residential and furnaces and domestic boilers
• Ambient and stack testing for CO
• CO safety measurements in and around combustion sources
• Temperature checking, including superheat and hydronic differential temperatures
• Dual input differential manometer

326 Calibratable Water Resistant Digital Pocket Thermometer with Needle Tip by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Field calibrateable to ±2°F
• Easy-to-read LCD
• Data Hold for hard to reach areas
• Penetration tip
• Auto off
• 3.1 mm stem for fast response
• 4.9 inch stem for insertion in liquids and semi-solids
• IP Rating IP67
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

708 Combustion Efficiency Analyzer with Flue Probe by Test Products International

The carbon monoxide sensor used in TPI combustion efficiency analyzers feature an on-board filter capable of filtering NO (nitric oxide), NO₂ (nitrogen dioxide) and NOX (combination of NO and NO₂) to prevent cross sensitivity errors.

Use TPI analyzers to test flue gases in gas and oil fired equipment including high efficiency furnaces and condensing boilers. Measure CO, O₂, and stack temperature.

Determine combustion efficiency, CO₂, and CO air free. Some models include built-in differential manometer, combustible gas detection, PC communication, data logging, and can measure NO / NOX.

Features

Using TPI analyzers to determine combustion efficiency at the time of equipment set up minimizes call backs and can be used to verify to the home owner the value of service work by showing the increase in equipment efficiency after work is performed. Efficiency calculation can also be used to generate business by demonstrating the need to improve the efficiency of equipment or to show the benefit of purchasing new equipment with higher efficiency.

Quick And Simple Set Up

All TPI analyzers feature quick and simple set up. Fast purge and the ability to perform fuel selectionduring start up enable tests to be performed quickly without requiring extra set-up time after initial startup. TPI analyzers also use the last selected fuel as the default setting. This feature prevents the need toperform fuel selection every time the analyzer is turned on.

• Measure CO, and temperature
• Calculate CO2, efficiency, excess air, and CO air free
• Pump driven for fast response
• Will not shut off if 15 ppm CO is present for increased safety
• Ten selectable fuels: Natural Gas, LPG, Light Oil, Heavy Oil, Bituminous Coal, Anthracite Coal, Coke, Butane, Wood, Bagasse
• Optional A740 IR printer available for hard copies of test results
• Built-in differential thermometer
• Store function to save up to 50 readings
• Large easy to read backlit display

Applications

• Tuning of residential and furnaces and domestic boilers
• Ambient and stack testing for CO
• CO safety measurements in and around combustion sources
• Temperature checking, including superheat and hydronic differential temperatures

715 High CO Combustion Analyzer with Built-in Differential Thermometer, Differential Manometer, and NO Measurement & NOX Calculation by Test Products International

The carbon monoxide sensor used in TPI combustion efficiency analyzers feature an on-board filter capable of filtering NO (nitric oxide), NO₂ (nitrogen dioxide) and NOX (combination of NO and NO₂) to prevent cross sensitivity errors.

Use TPI analyzers to test flue gases in gas and oil fired equipment including high efficiency furnaces and condensing boilers. Measure CO, O₂, and stack temperature.

Determine combustion efficiency, CO₂, and CO air free. Some models include built-in differential manometer, combustible gas detection, PC communication, data logging, and can measure NO / NOX.

Use the optional A784 flow regulator to reduce the flow rate of the gas being sampled to measurable levels on high pressure systems such as gas compression engines. The A784 is included in the 715K3 kit.

Features

Using TPI analyzers to determine combustion efficiency at the time of equipment set up minimizes call backs and can be used to verify to the home owner the value of service work by showing the increase in equipment efficiency after work is performed. Efficiency calculation can also be used to generate business by demonstrating the need to improve the efficiency of equipment or to show the benefit of purchasing new equipment with higher efficiency.

Quick And Simple Set Up

All TPI analyzers feature quick and simple set up. Fast purge and the ability to perform fuel selection during start up enable tests to be performed quickly without requiring extra set-up time after initial startup. TPI analyzers also use the last selected fuel as the default setting. This feature prevents the need toperform fuel selection every time the analyzer is turned on.

• Measure up to 9.999% CO
• Built-in differential thermometer
• Measure NO (Nitric Oxide), Calculate NOx
• Store function to save up to 10 readings
• Calculates combustion efficiency
• Pump driven for fast response
• Push on fittings for fast and easy use
• Large easy to read backlit display
• Will not shut off if 15 ppm CO is present for increased safety
• Four selectable fuels: Natural Gas, LPG, Light Oil, Heavy Oil
• Optional A740 IR printer available for hard copies of test results

Applications

• Tune combustion engines
• Test CO levels in industrial boilers
• Measure NO and calculate NOX

312C Calibratable Water Resistant Digital Pocket Thermometer by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Field calibrateable to ±2°F
• Easy-to-read LCD
• Data Hold for hard to reach areas
• Penetration tip
• Auto off
• 3.1 mm stem for fast response
• 4.9 inch stem for insertion in liquids and semi-solids
• IP Rating IP67
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

HXG-2 Combustible Gas Leak Detector by Test Products International

As lightweight and portable as it is sensitive, the HXG2 helps you pinpoint the smallest leaks quickly and accurately. Its calibrated alarm will indicate dangerous concentrations of combustible gases. Use with Hetkit and AGA approved protocol to test for cracked heat exchanges

Features

• Combustible Gas Leak Detector capable of displaying ppm or %LEL (Lower Explosive Limit).
• UL 913 intrinsic safety rating
• Calibrated to NIS traceable standards
• Instant response
• 10 ppm sensitivity
• Adjustable tic rate
• Settable alarm
• Visual and audible leak indication
• 16'' gooseneck
• Soft Carrying Pouch

706 High CO Analyzer by Test Products International

Measure up to 99,999 ppm with the TPI 706 tests forklift exhaust gases for the presence and location of carbon monoxide leaks. This instrument fits comfortably in your hand and operates with just the push of a button.

The 706 is an advanced state-of-the-art carbon monoxide (CO) gas analyzer designed to provide part per million readings from 0- 10,000 ppm. The 706 is capable of performing ambient as well as flue gas checks with its hot air probe and internal pump.

The 706 is utilizes an advanced long life electrochemical sensor that can be field calibrated and has a low replacement cost.

Features include IR printer port to print hard copy of data, 10 storage locations, Flow block indication, peak reading for test period as well as date and time.

Features

• Pump driven for fast response
• Store function to save up to 50 readings
• Will not shut off if 15 ppm CO is present for increased safety
• Push on fittings for fast and easy use
• Optional A740 IR printer available for hard copies of test results
• Large easy to read backlit display

Applications

• Check forklift exhaust gases for the presence and location of carbon monoxide

Quick And Simple Set Up

All TPI analyzers feature quick and simple set up. Fast purge and the ability to perform fuel selection during start up enable tests to be performed quickly without requiring extra set-up time after initial startup. TPI analyzers also use the last selected fuel as the default setting. This feature prevents the need toperform fuel selection every time the analyzer is turned on.

• Range: 0 ~ 9,999ppm <10,000ppm: 1.000 ~ 9.999%
• 1 ppm sensitivity
• Pump driven
• Auto zero

709 Combustion Efficiency Analyzer and Differential Manometer by Test Products International

The carbon monoxide sensor used in TPI combustion efficiency analyzers feature an on-board filter capable of filtering NO (nitric oxide), NO₂ (nitrogen dioxide) and NOX (combination of NO and NO₂) to prevent cross sensitivity errors.

Use TPI analyzers to test flue gases in gas and oil fired equipment including high efficiency furnaces and condensing boilers. Measure CO, O₂, and stack temperature.

Determine combustion efficiency, CO₂, and CO air free. Built-in differential manometer, combustible gas detection, PC communication, data logging, and can measure NO / NOX.

Features

Using TPI analyzers to determine combustion efficiency at the time of equipment set up minimizes call backs and can be used to verify to the home owner the value of service work by showing the increase in equipment efficiency after work is performed. Efficiency calculation can also be used to generate business by demonstrating the need to improve the efficiency of equipment or to show the benefit of purchasing new equipment with higher efficiency.

Quick And Simple Set Up

All TPI analyzers feature quick and simple set up. Fast purge and the ability to perform fuel selectionduring start up enable tests to be performed quickly without requiring extra set-up time after initial startup. TPI analyzers also use the last selected fuel as the default setting. This feature prevents the need toperform fuel selection every time the analyzer is turned on.

• High resolution 0.001 in H20 differential manometer for high efficiency and oil equipment
• Measure CO, and temperature
• Calculate CO2, efficiency, excess air, and CO air free
• Pump driven for fast response
• Will not shut off if 15 ppm CO is present for increased safety
• Ten selectable fuels: Natural Gas, LPG, Light Oil, Heavy Oil, Bituminous Coal, Anthracite Coal, Coke, Butane, Wood, Bagasse
• Optional A740 IR printer available for hard copies of test results
• Built-in differential thermometer
• Store function to save up to 50 readings
• Large easy to read backlit display

Applications

• Tuning of residential and furnaces and domestic boilers
• Ambient and stack testing for CO
• CO safety measurements in and around combustion sources
• Temperature checking, including superheat and hydronic differential temperatures
• Dual input differential manometer

365 K-Type Thermocouple Thermometer by Test Products International

TPI contact temperature testers are accurate, reliable, and built to last. Models 341K, 343 and 367D can be auto field calibrated to system accuracy (tester plus probe) of ± 1°F in less than 10 seconds in ice water.

Auto Field Calibration Perform ice bath calibration to achieve ±1°F system accuracy within the 30°F to 120°F temperature range. Calibration is an easy two-step process performed with instrument keypad, no additional tools needed.

Features:

• Large two line LCD display with clock display, alarm clock, alarm timer, and over temperature alarm
• Multi use belt clip (A366): can used as a belt clip or wall mount
• Auto Resolution (0.1° / 1°)
• °C/°F Selectable
• Auto Off
• Overmolded case
• Up to 14,000 hour battery life (AA alkaline batteries x 2)

1010A Indoor Air Quality Meter by Test Products International

Measure ambient CO2, temperature, relative humidity, dew point, wet bulb, CO, and calculate percentage outside air. The TPI 1010A Indoor Air Quality (IAQ) Meter is a state of the art, easy to use tester designed to provide you with the necessary measurements to monitor and make adjustments to air handling devices.

The 1010A IAQ meter uses state of the art sensors to measure humidity, carbon dioxide (CO2), and temperature. The instrument is ruggedly constructed and comes with a 3 Year unit and 2 Year sensor Guarantee.

Features

• Calculate percent outside air to maintain acceptable CO2 levels in buildings and work spaces
• Measure and display Carbon Dioxide (CO2) and Carbon Monoxide
• Measure ambient air temperature
• Measure relative humidity, dew point and wet bulb
• Log up to 10,000 readings in 1 second to 1 hour intervals
• Download to a computer using the A368 USB cable
• Print via I/R to optional printer (Model A740)

Applications

• Check ambient CO and CO2 levels in work and living spaces
• Monitor results of air control systems
• Ambient air temperature and humidity
• Test dew point and wet bulb humidity

Standard Accessories

• TPI 1010A Instrument
• Protective Rubber Boot (A800)
• Soft Carrying Case (A921)
• USB Cable & Software (A803)
• Instruction Manual

Optional Accessories

• Power adapter / Battery eliminator (A804)
• Magnetic strap kit to hang meter (A127)
• Boot hook to hang meter (A103)
• Replacement Software only (A802)
• Replacement USB cable only (A801)

316C Calibratable Pocket Digital Thermometer without Magnets by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Auto field calibration to ±2°F
• Tapered stem (3.1 mm diameter) to fit into a Pete's Plug
• Reinforced, heavy-duty housing for strength
• -Waterproof (IP63)
• Fits in your pocket
• -58°F to 300°F (-50°C to 150°C)
• Rugged design to withstand a 10 foot drop
• Magnetic clip perfect for air duct applications
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

340/C1 Single Input K-Type Thermocouple Thermometer by Test Products International

TPI contact temperature testers are accurate, reliable, and built to last. Models 341K, 343 and 367D can be auto field calibrated to system accuracy (tester plus probe) of ± 1°F in less than 10 seconds in ice water.

Auto Field Calibration Perform ice bath calibration to achieve ±1°F system accuracy within the 30°F to 120°F temperature range. Calibration is an easy two-step process performed with instrument keypad, no additional tools needed.

Features:

• Single button operation
• Auto Resolution (0.1° / 1°)
• °C/°F Selectable (Switch in battery compartment)
• Auto Off
• Protective rubber boot
• Easy to read LCD display

Includes:

• 340 Temperature Tester
• A304 tilt stand protective boot
• GK12M temperature probe
• A340 soft pouch
• Batteries
• Instruction Manual

315C Calibratable Pocket Digital Thermometer with Magnets by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Auto field calibration to ± 2F
• Tapered stem (3.1 mm diameter) to fit into a Pete's Plug
• Reinforced, heavy-duty housing for strength
• Waterproof (IP63)
• Fits in your pocket
• -58°F to 300°F (-50°C to 150°C)
• Rugged design to withstand a 10 foot drop
• Magnetic clip perfect for air duct applications
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

P250B Non-Switchable Passive Oscilloscope Probe, 250MHz, x 10, 1.2M Cable Length by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

133 Manual Ranging DMM, with Boot, Test Leads, Battery and Manual by Test Products International

The 133 is a hand-held autoranging DMM. It features extra large numerals on the LCD, and Data Hold for all functions and ranges. The 133 is an affordable choice offering measurements in all of the basic electrical functions.

Features:

• Safety: Meets CE and IEC 1010 requirements. UL Listed to U.S. and Canadian Safety Standards.
• Large LCD:Easy to read at all angles and the majority of lighting levels. 4000 Count.
• Rubber Boot: Added protection when the instrument is dropped. (135NB does not include boot.)
• Multi-function: Measure all electrical characteristics with one meter.
• 0.5% DCV basic accuracy
• 0 to 750 ACV; max resolution 1mV
• 0 to 1,000 DCV; max resolution 0.1mV
• 0 to 20MΩ; max resolution 0.1Ω
• 0 to 10 amps AC/DC; 0.1uA resolution
• Data Hold
• cULus 61010-1
• CAT II - 1000V, CAT III - 600V

Applications:

• Thermocouples in furnaces and gas appliances
• Heat anticipator current in thermostats
• Line and control voltages
• Flame safety control current
• Heating element resistance
• Continuity of wiring
• Line current up to 10 amps
• Power supply current

The 133 comes complete with the following accessories:

• 133 Instrument
• Rubber Boot (133NB does not include boot)
• Test Lead Set
• Battery
• Instruction Manual

367D Data Logging Thermometer (K & T-Type Thermocouple & Thermistor) by Test Products International

TPI contact temperature testers are accurate, reliable, and built to last. Models 341K, 343 and 367D can be auto field calibrated to system accuracy (tester plus probe) of ± 1°F in less than 10 seconds in ice water.

Auto Field Calibration Perform ice bath calibration to achieve ±1°F system accuracy within the 30°F to 120°F temperature range. Calibration is an easy two-step process performed with instrument keypad, no additional tools needed.

Features:

• Auto Field Calibration Perform ice bath calibration to achieve ±1°F system accuracy within the 30° F to 120°F temperature range. Calibration is easy two-step process performed with keypad, no additional tools needed
• Data logging capability: 16,000 readings with sampling interval from 1 second upto 24 hours.
• Auto Resolution (0.1° / 1°)
• Store 16 readings
• Real time and logged data transfer to PC via optional USB docking station (A367)
• Multi use belt clip (A366): can used as a belt clip or wall mount
• Large two line LCD display with clock display, alarm clock, alarm timer, and over temperature alarm
• Fast reading mode - Increases sample rate
• Min/Max Record and Data Hold
• Selectable Resolution (0.1° / 1°)
• °C/°F Selectable
• Up to 14,000 hour battery life (7,000hrs data logging) (AA alkaline batteries x 2)
• Auto Off
• Overmolded case

343C5 Dual Input K-Type Thermocouple Thermometer with Two GK13M Probes and Two CK24M Probes A901 Carrying Case by Test Products International

TPI contact temperature testers are accurate, reliable, and built to last. Models 341K, 343 and 367D can be auto field calibrated to system accuracy (tester plus probe) of ± 1°F in less than 10 seconds in ice water.

Auto Field Calibration Perform ice bath calibration to achieve ±1°F system accuracy within the 30°F to 120°F temperature range. Calibration is an easy two-step process performed with instrument keypad, no additional tools needed.

Features:

• Auto Field Calibrate in less than 10 seconds in ice water to achieve ± 1°F system (tester & probe) accuracy within 30°F to 120°F temperature range
• Temp1, Temp2, Temp1-Temp2 display modes
• Min / Max Record
• Auto Resolution (0.1° / 1°)
• °C/°F Selectable
• Hold feature freezes reading on display
• Auto Off
• Protective rubber boot
• Easy to read LCD display

Includes:

• Two GK13M temperature probe
• A908 Case
• Two CK21M pipe clamp probes

HXG-2D Combustible Gas Leak Detector by Test Products International

The HXG-2D offers 10ppm sensitivity to detect combustible gasses. Easily operated with new patent pending electronic tick control, leaks are pinpointed using the audio and visual indicators. Backlit LCD display of gas leaks in ppm or %LEL.

Features

• Combustible Gas Leak Detector capable of displaying ppm or %LEL (Lower Explosive Limit).
• Designed to meet UL 913 intrinsic safety (Approval Pending)
• 10 ppm sensitivity (methane)
• Instant response
• Electronic tick rate control
• Settable alarm
• Visual and audible leak indication
• 16'' gooseneck
• Hard carrying case

Applications

• Detect combustible gasses including natural gas methane, propane (LPG), gasoline, diesel, and kerosene
• Trace natural gas lines and fittings for leaks
• Check gas generation for leaks

How big is the leak?

• Direct PPM readout
• Direct "LEL" percent readout

Find Leaks Quickly

• New "Patent Pending" electronic tick control
• Ideal for Natural, Propane and Butane gas leaks

Safe, Durable and Reliable

• Intrinsically safe design
• SENSIT "ruggedized" design

Partial List of Industries:

• Utility Companies
• Gas Processing Plants
• Propane Marketers
• Safety Engineers
• Fire and Police
• Emergency Vehicles
• Appliance Repair
• Plant Maintenance
• Plumbing Contractors
• Furnace Heat Exchanger Testing
• Marine Operations
• Heating and Air Conditioning
• Municipalities
• Mobile Home Parks
• Apartment Buildings

307C Calibratable Low Cost Pocket Digital Thermometer with Needle Tip with A306 by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Compact and convenient
• Easy-to-read, large LCD
• Auto power off
• Data hold for hard to reach areas
• A306 protective rubber boot offers protection from drops
• 307C with needle tip

775 Combination Carbon Monoxide & Combustion Gas Leak Detector by Test Products International

The combo CO/Combustible gas detector is the first of its kind to combine both detection technologies into one easy to use hand-held andaffordable instrument.

The TPI 775 is a state-of-the-art Carbon Monoxide and Combustible Gas Leak Detector. It is the first of its kind to combine both detection technologies into one easy to use hand-held affordable instrument.

Features

• Easy to use
• One hand operation
• Auto Zero
• Back light
• Visable and audible alarm

Applications

• CO safety measurements in and around combustion sources
• Ambient CO safety checks

Standard Accessories

• Instruction Manual
• Soft Pouch

Optional Accessories

• Earphones