Test and Measurement

ADF25C Differential Probe by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

08610-32 Traceable® Clip-It Single-Channel Digital Timer with Calibration by Digi-Sense

Timer counts down in hours or minutes and also functions as a stopwatch. Acts as a handy reminder for meetings or tasks. The 1/3-inch four-digit display is easy to read. Features time-out function in both up and down counting. Weighs only 1/2 ounce. Features a chemical-resistant ABS case and a magnet for attaching to metal.

Traceable® products are calibrated to NIST-traceable standards and ready to use as soon as you receive it. Each product goes through an intense vetting process before it can carry the Traceable name, and it includes NIST-traceable certification. This means that a 17025-accredited calibration test lab has confirmed that the product meets or exceeds all stated specifications, saving you both time and money by not having to calibrate separately.

NIST-traceable calibration also helps you meet quality standards and regulatory compliance for ISO, FDA, cGMP, VFC, CAP, CLIA and Joint Commission requirements.

Features:

• Get accurate, reliable measurements with included NIST-traceable calibration

Includes:

NIST-traceable calibration certificate with data, magnet, clip, and battery.

GHS1282 Not a Controlled Product Label (Paper) by GHS Safety

Shipping Labels are essential for packages that contain dangerous goods. GHS labels are available in two materials. Paper for indoor applications and in vinyl for extended outdoor usage using a fade resistant ink. These labels meet the UN Recommendations on the Transport of Dangerous Goods.

Available in 500/roll formats.

6173KAA Benchtop pH/mV/Temperature Meter Kit by Jenco

pH/mV/Temp benchtop meter with an extra large LCD display for ease of use. Features a splash proof and rugged case ideal for schools and universities. Features EEF, Electrode Efficiency Function, multiple buffers 4.00, 4.01, 6.86, 7.00, 9.18 & 10.0 and automatic slope, buffer and electrode offset recognition. Has power down memory backup and works on 6 AA batteries or 115/230 V AC adapters. CE Approved & ISO 9001 Certified.

Includes:

• 6173 Benchtop pH/mV/Temperature Meter
• 600P pH Electrode
• 6230A-ST Probe
• 6230D115 AC Adapter
• Probe Holder Arm

• Larger LCD display
• Buffers recognition
• Electrode offset recognition
• Electrode slope recognition
• Built in buffer temp. coefficient
• Auto lock
• Touch keys with audio feedback
• Power down memory
• Battery/ac adaptor
• Low power consumption
• Battery low indicator
• Percentage of power supply display

AZF686300 Microtox SOLO Reagent, 50 vials per box by Modern Water

SOLO Reagent is the same as Acute Reagent - packaged to run a single test

Accessories required:

• Disposable Glass Cuvettes: box of 1000 - AZF686004
• Cuvette Racks (set of 5) - AZF686250
• Oxford® Fixed Volume 10 uL Pipette (for high toxicity protocol only) - AZF686067
• Adjustable Volume Pipette: 10 - 100 uL - AZF686087
• Adjustable Volume Pipette: 100 - 1000 uL (for all protocols) - A00176
• 10-100 uL Wide Bore Pipette Tips: tray of 96 - AZFV020
• 100-1000 uL Wide Bore Pipette Tips: tray of 100 - AZFV021
• Microtox® Diluent: 1L bottle - AZF686011
• Microtox® Osmotic Adjusting Solution: 1 x 50 mL - AZF686019

08068-20 Irreversible 8-Point Vertical Temperature Label, 100-150F/37-65C; 25/Pk by Digi-Sense

Labels are made up of a series of temperature-sensitive elements sealed between heat-resistant substrates with transparent windows. Each element changes color distinctly as its rated temperature is met or exceeded. The changes to the label are irreversible, providing a temperature history of the surface being monitored. The labels will not delaminate when removed, allowing them to be attached to an inspection report to serve as a permanent record. Ideal for use in the food, automotive, molding and metal working industries. Accuracy is ±1.8°F below 212°F and ±1°F above 212°F. Shelf life: 1 year after date of purchase.

Reliable proof that the product was maintained at the correct temperature

• Used as a quick inspection tool that the product is in usable condition during the shipping and receiving process
• Save time and money due to costly recalls
• Self-adhesive design

0560 4101 410-1 Pocket Pro Air Velocity & Temperature Meter by Testo

testo 410-1 measures air speed and temperature. It is ideal for quick spot checks at air outlets on account of its integrated measurement with the 40mm vane. Timed mean calculation is possible. In addition to air speed and temperature, testo 410-2 also measures air moisture. Testo's very own, patented humidity sensor guarantees accurate readings. In this way, air conditions can be reliably checked.

• Flow velocity measuring instrument with temperature measurement
• Integrated measurement with 40 mm vane
• Timed mean value calculation
• Hold function and max./min. values
• Windchill calculation for outside areas (perceived temperature)
• Display illumination
• Protective cap for safe storage
• Including wrist strap, belt holder and calibration protocol

701JF Temperature Magnetic Back Meter, Type J by Jenco

Model 701 is a battery operated thermocouple type digital thermometer that measures approximately 3x2.25x1.13 inches (77x60x30mm). It is available in 6 different configurations of thermocouple calibration with Celsius or Fahrenheit reading.

• All solid state design
• High stability
• Wide temperature range
• cold junction compensation
• Easy to read LCD display
• One conventional 9V battery
• Long battery life
• Interchangeable TC sensor

93800-12 Type K Industrial Direct Insert Ungrounded Thermocouple Probe 12" L by Digi-Sense

Thermocouple Probes are ideal for use in industrial applications, chemical processes, production lines, ovens, furnaces, and vessels. The probes conductor is made of 18 gauge wire and is encased with Magnesium Oxide insulation, and has a 316 stainless steel sheath. Featuring a standard size aluminum protection head with a gasketed cap to seal out dust and moisture and houses a ceramic terminal block. Head has a 3/4" NPT(F) opening on the side for easy connection to electrical conduit.

Spring loaded probes: designed to bottom out when inserted in to a thermowell to produce an accurate reading. (Not designed for direct insertion in to medium)

Non-spring loaded probes: designed to be directly inserted into the medium being measured without the use of a thermowell.

0560 1128 110 112 NTC Food Thermometer by Testo

The calibratable testo 112 precision temperature measuring instrument was designed specially for official inspection measurements. The instrument is approved for official measurements by food inspectors, assessors and official authorities on account of its PTB design approval and the option of calibrating it. A built-in self-test indicates correct functioning before measurement begins. Owing to its wide measuring range, testo 112 is the ideal temperature measuring instrument for all areas of food monitoring. NTC probes (thermistor probes) and Pt100 probes (platinum resistance probes) can both be attached to the probe input, so that a wide temperature range is covered, ranging from deep-frozen products to deep-fat fryer monitoring. In order to document readings, testo 112 provides the possibility of printing data directly on site with date and time. This is particularly interesting for food hygiene inspectors. If adjustable high or low limit values are exceeded, the instrument immediately sounds an audible alarm. Minimum and maximum limit values can be conveniently called up in the two-line display. It is possible to print out readings on site on the Testo printer (optional).

• The instrument for official food inspections
• Data printout on site on the Testo fast printer (optional)
• TopSafe, indestructible protection case (optional)
• Large, backlit display with 14 mm high characters
• Call up max/min values at the touch of a button
• Highly accurate, officially calibratable temperature measuring instrument
• Minimum/maximum value memory

URSA II - Universal Radiation Spectrum Analyzer by SE International

The URSA II, with a full-featured MCA program, can be used with practically any radiation detector and can extract any data your detector can supply! It has been designed taking into account comments and requests from our current URSA customers. URSA-II MCA, the all-new fully, quantitative Windows™ based URSA-II software package has been designed for ease of use in a 32-bit Windows™ environment. Software also includes URSA-II for PPC software to run the URSA-II using a Windows Mobile™ Device (Jornada, iPAQ, TDS Recon, etc.) running WindowsCE™ or Windows Mobile™. The Software can be installed on as many computers as you like, with no restrictions and includes free software updates.

Specific applications include:

• Bulk sample analysis
• Air sample analysis
• Wipe sample analysis
• Thyroid assay
• Compliance monitoring
• Environmental monitoring
• Nuclear medicine
• Identification of unknown nuclides
• Remote monitoring
• Health physics
• Homeland defense
• Portal monitoring
• Education

700 Portable Compliance-Level Combustion Emissions Analyzer by Enerac

Enerac brings you the model 700 The most accurate, reliable, rugged and affordable multi parameter, compliance level, portable combustion analyzer. The Enerac 700 is unmatched in versatility. It is designed to help you meet the challenges of a rapidly changing regulatory environment.

Compact/Rugged

The Enerac Model 700 is handheld, weighs 6 lbs and is easy to operate (no technical expertise is needed). The Model 700 units are rugged, made with a metal case and considered the workhorse of the industry withstanding years of use and abuse. No one makes a more affordable, accurate, rugged, reliable and sophisticated portable combustion emissions analyzer than Enerac. Enerac custom builds all units and can engineer sensor ranges and options to customer requirements for their respective application(s) at hand.

Versatile

The Enerac Model 700 is used for a vast array of applications. The most common applications are those related to combustion sources, such as Boilers, Burners, Engines, Turbines, Generators, Kilns, Dryers, Heaters, Ovens to name a few. The Enerac Model 700 is also of interest to Scientists and their respective combustion/emissions experiments typically found at the University research environment as well as in the private sector.

User Friendly

The Enerac Model 700 units have easy access for replacing sensors in the field. The back of the unit has easy thumb screws to pop off the back plate. Once the back plate is off, the sensors are easy to see and pop in and out. These sensors are field replaceable (the unit does not need to be sent back to the factory for sensor replacement). The Model 700 also has the ability to be field calibrated without having to send the unit back to the factory! Free factory tech support is always available if need be.

Compliance Level

The Enerac Model 700 is fully upgradeable (one can order new sensors and options to the same unit over time). The Model 700 also has a standard sample conditioning system (thermoelectric condenser also called a peltier cooler) necessary for the proper detection and measurement of both NO2 and/or SO2 gasses. The Model 700 also has proper control over the NO sensors tendency to drift over time with increasing ambient temperatures. The Enerac Model 700 s NO SEM sensor incorporates a proprietary temperature control system designed to automatically hold the nominal filter and sensor temperatures at < 30 degrees C. This ultimately prevents rising measurement data drift and maintains the actual lower readings of the NO (NOx). This in turn prevents one from overstating one s NO (NOx) emissions.

The Enerac Model 700 combines a high quality tubing (Viton hose with its specific dimensions and flow rate) along with an accurate and reliable conditioning system (peltier cooler) with the additional benefits of the extremely accurate SEM sensors. The result is a Compliance-Level Emissions Analyzer that produces reliable, accurate data in the palms of your hands.

The Enerac Model 700 is perfect for gathering extremely accurate and reliable data for internal needs as well as for the necessary emissions reporting requirements for local, district, county, state and federal agencies. The Model 700 Is perfect for S.C.A.Q.M.D. compliance requirements (and the other CA districts) EPA compli-ance tests (i.e. ctm 30, ASTM 6522, ctm 34, for CO, (NOx) requirements etc.), method 2 (stack gas velocity), and method 25B (Hydrocarbons).

Communications

The Enerac Model 700 comes with 500 internal storage buffers for storing collected data during a testing event. With Enerac s free Enercom software, one can use during the testing event or download the stored data at a later date. There is a serial port (RS 232 port), USB port and Blue tooth for communicating with your Enerac Model 700 and your computer.

Enerac Model 700 Base unit Includes

O2 (Oxygen), CO (Carbon Monoxide) SEM Sensor Dual Range (Dual range is not available if Combustible Sensor is Selected), Draft (not available with pitot tube/velocity option), Combustibles (not available with NDIR opt.), Stack & Ambient Temperature, Computes Efficiency, CO2 & Excess air.; with a 4&8 line 128 x 64 pixel dual display with backlight, Emissions Calculation, Auto Zero, RS-232 Port, USB port, Rechargeable Battery, AC Adapter, Built-In Printer, Storage (400 Complete Test Printouts), Blue Tooth, Enercom Software cd, Travel Case, in-line filter, roll of printer paper, manual, Calibration Certificate and a Two Year Warranty on the Unit and a Two Year Warranty (Pro-Rated) on the Sensors

0560 5126 512 Digital Manometer/Anemometer +/- 1" WC (0 to 2hPa) by Testo

testo 512 simultaneously shows pressure and flow velocity (apart from version 0 to 2000 hPa) in the large, easily legible, illuminated display, the measurement values can be printed out on site with date and time as well as minimum and maximum values.

testo 512 has two switchable units for flow velocity, and for pressure, eight units can even be set.

In the testo 512, damping for a sliding mean value calculation can be individually programmed, tightness compensation is integrated. The actual value displayed can be frozen in the display with the Hold-button, and the minimum and maximum values can be displayed and stored in the instrument.

The TopSafe protects the instrument from impact, dirt and splash water in tough practical applications (optional).

The differential pressure measuring instrument testo 512 is available in four different versions:

• Measuring range 0 to 2 hPa
• Measuring range 0 to 20 hPa
• Measuring range 0 to 200 hPa
• Measuring range 0 to 2000 hPa (without flow velocity and Pascal measurement)

• 8 pressure units can be selected: kPa, hPa, Pa, mm H2O, mmHg, psi, inch H2O, inch Hg
• 2 flow velocity units can be selected: m/s, fpm
• Integrated tightness compensation
• Display illumination
• Max./min. as well as Hold-function
• Printout of measurement values incl. date/time and min./max. values

97610-51 LDM-65 Compact Handheld Laser Distance Meter by Digi-Sense

These laser distance meters are designed for high-accuracy measuring at an economical price. Compact size and simple-to-use push-button control with shortcut keys makes measuring fast and reliable.

• Measure up to 213 ft (65 m)
• Calculation of area (square footage) and volume
• Indirect measurement using Pythagoras calculation
• Continuous measurement
• Addition and subtraction of measurement
• Min/Max distance tracking
• Multiline and illuminated display

Includes

carrying case and batteries.

SP100B Switchable Passive Oscilloscope Probe, 100MHz, 1.2M Cable Length by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

TT220TB Tagboard Class 2.2 Non-Flammable, Non-Toxic Gases Placard (10.75" x 10.75") by GHS Safety

Placards are displayed on vehicles, tankers, and containers to identify the risk of products being transported. GHS Line of placards are manufactured to meet the UN specifications on the Transport of Dangerous Goods.

These placards are stocked in 3 materials. Paper Tag-board placards are a cost effective single use format. Rigid Plastic placards will withstand multiple uses even in adverse weather conditions.

Outdoor Grade Peel and Stick Vinyl placards offer a permanent marking solution and will withstand outdoor environments.