Honeywell Analytics

2106B2310 Sensepoint Hazardous Area Approved Gas Detector, HT Flammable Sensor (ATEX) M20 by Honeywell Analytics

The Sensepoint range of flammable, toxic and Oxygen gas detectors offer users a high quality, low cost solution to their industrial gas monitoring needs. Installation in potentially explosive atmospheres is made by the use of a suitable Ex d or Ex e approved junction box. The industry standard outputs from Sensepoint are connected to either a choice of Honeywell Analytics' controllers or 3rd party DCS/ PLC systems. Both flammable and toxic versions are certified to the latest ATEX/IECEx safety and performance standards.

The flammable detector is available in either % LEL or PPM detection range versions and provides an industry standard mV bridge output. Typical life expectancy is greater than 5 years, after which the detector is simply replaced with a new one.

The toxic detectors are supplied pre calibrated for easy installation and provide an industry standard 2 wire 4-20mA loop output. User connections are Ex d, while front end Intrinsic Safety (IS) design allows for easy exchange of the replaceable sensor while powered. IS design also removes the need for a sinter enabling very fast speed of response and detection of 'sticky' gases such as Chlorine and Ammonia.

Sensepoint has proven its suitability across a wide range of demanding applications by delivering high performance and reliability at an affordable cost.

Fit For Purpose

• Flammable, toxic and Oxygen versions available
• High performance, low cost
• Suitable for new and retro fit applications

Proven Sensor Technology

• Surecell™ electrochemical sensors
• Poison resistant catalytic bead
• Fast and reliable
• Typical 2 to 5 years operational life

ATEX/IECEx Certified

• Complies with the latest standards
• Hazardous area approval and performance
• IP65/67 for use in harsh environments

Easy to Use

• Factory set operation
• Simple to replace
• Minimal training required

Range of Accessories

• Weatherproof cap
• Flow adaptor
• Duct mounting kit
• Collecting cone

1309A0037 E3Point Gas Monitor, Nitrogen dioxide (NO2); -40° to 50°C (-40° to 122°F) by Honeywell Analytics

Toxic/combustible gas monitor that makes a commercial operation run more intelligently to protect people, property and the bottom line.

Product Overview:

E3Point is capable of detecting the widest range of toxic and combustible gases found in commercial building spaces and outbuildings, including CO, NO2, O2, H2, H2S, CH4 and C3H8. It can be used as a standalone unit with single or dual-gas detection (i.e. using a remote sensor) or deployed as a networkable device (interoperable with BACnet, Modbus or other Building Automation System): E3Point also functions with existing controller-based gas monitoring systems and wired-wireless gas monitoring system components.

E3Point uses Demand Control Ventilation—through relays, Building Automation System (BAS) or controller—to increase energy savings, extend fan life and align with green building best practices. In its network configuration, E3Point also optimizes HVAC, fire/smoke, surveillance and other building systems performance.

Intelligent product design reduces the unit's cost of ownership while increasing flexibility of application. Smart sensors are pre-calibrated, auto-configure upon set-up and operate continuously on patented Reflex© technology which continuously monitors sensor cell condition and alerts user to fault status. The plug-n-play sensor cartridge, user-friendly menu and wiring options simplify installation and maintenance, and reduce the cost of gas monitoring over the life of the unit.

Flexible Operation:

• Comes in standalone, standalone with remote (dual gas mode) or network versions
• Connects to analog or digital systems
• Works with virtually any BAS including BACnet and Modbus
• Connects to wired or wireless system (via 301CW wireless controller)
• Wall or duct mount
• Factory-calibrated cartridges

Cost Effective:

• Saves energy through Demand Control Ventilation (DCV)
• Simplifies installation/maintenance through plug-n-play sensor
• Remote sensor option provides dual gas monitoring (standalone version only)
• Optimizes BAS, fire, ventilation and other security systems

Versatile Communications:

• Works through BAS to improve fault diagnostics and collect data on gas concentration levels, sensor condition, etc.
• Couple with 301C to log data and daisy-chain up to 96 E3Point units

Advanced Sensing Technology:

• Detects CO, NO2, O2, H2, H2S, CH4, C3H8
• Advanced electrochemical (for toxic gases)and catalytic bead (for combustible gases) sensor performance
• Uses patented Reflex® and smart cartridge technologies

Electrical Certifications:

• US (ANSI/UL 61010-1)
• Canada (CSA C22.2 No. 61010-1)

Features & Benefits:

• Standalone, standalone with remote (dual gas mode) or network versions available
• Saves energy through Demand Control Ventilation

Quick Specs:

• Complete toxic and combustible gas detection system with onboard sounder
• Available in single point or dual gas options
• Analog 4-20 mA or Digital outputs (Bacnet, Modbus, and Lonworks)

2108N4010H Optima Plus Gas Detector, hydrocarbon version, HART® over 4 to 20mA output, ATEX/IECEx, M25 thread spigot, electro polished 316SS, includes pre-fitted remote gassing cell, polyester mesh dust barrier, nylon weather protection housing and LNP Faradex deluge/sunshade by Honeywell Analytics

Market leading point infrared Hydrocarbon gas detector offering proven performance and sensitivity

With over 40 years experience in the design, manufacture, installation and maintenance of point infrared gas detection, Honeywell Analytics currently has a Worldwide installed base of over 100,000 infrared point Hydrocarbon gas detectors in a wide spectrum of applications from light industrial to the most demanding of offshore petrochemical environments.

Searchpoint Optima Plus is an infrared point Hydrocarbon gas detector certified for use in potentially explosive atmospheres. The unit's infrared detection principle offers the fastest speed of response and fail-to-safe operation, ensuring that your plant is compliant, your personnel are protected and your production process can deliver maximum uptime. Reduced routine maintenance, when compared with conventional electro-catalytic based gas detectors, provides low ongoing cost of ownership. The development of advanced internal fault diagnostics and false alarm rejection algorithms ensures that Searchpoint Optima Plus delivers the highest level of operational integrity.

Typical applications include environments that may suffer from the presence of catalytic bead poisons or inhibitors, or where there are harsh environmental conditions forcing increased time between routine maintenance, for example; offshore oil and gas platforms, floating production storage and offloading (FPSO) vessels, tankers, onshore oil and gas terminals, refineries, LNG / LPG bottling plants, gas compressor / metering stations, gas turbine power plants, refineries, solvent printing and coating plants.

Over 100 gas and vapour calibrations are available. For a list of detectable gases and vapours, please contact our Customer Support team or your local distributor.

Why Infrared?

• Failsafe operation
• Fast speed of response
• Reduced routine maintenance
• Immune to catalytic poisons
• Long operating life
• Works in inert atmospheres

Why Searchpoint Optima Plus is the right choice...

• Experience gained from over 100,000 units installed worldwide
• Improved reliability
• Optional HART® over 4-20mA output
• Can detect a wide range of hydrocarbon gases including solvents
• Increased reliability with no moving parts
• Increased stability from self compensating optics
• Immune to long term component drift
• Remote functional gas test facility
• Certified for North American and European Hazardous areas
• Increased false alarm rejection
• Increased uptime with contaminated optics warning
• Dynamic Heating Control ensures condensation free optics
• No undetected failures
• Improved diagnostics
• Integral event logging
• Reduced power consumption
• Certified to many hazardous area classification schemes including: European (ATEX), UL, CSA, IECEx and more

SPLCO1BMXCXNZZ Sensepoint XCL Fixed Gas Detector, Bluetooth Connection, O2 25.0%VOL, Modbus, Charcoal by Honeywell Analytics

Sensepoint XCL is a fixed point gas leak detector that is designed to meet the needs of commercial and light industrial applications. With over 50 years experience in gas leak detection, Honeywell offers a flexible range of highly-reliable sensing devices to meet those needs.

• Quicker installation
• Rapid configuration
• Simple to operate
• Straightforward to maintain

Honeywell innovation enables customers to pair the gas detector with their mobile phone, and then use an app to perform many tasks related to installation, commissioning and maintenance.

Flexible Output Options

Sensepoint XCL is available with either mA loop analog output or Modbus RTU with the option for relays on both. The result is a flexible solution that can easily be incorporated into legacy systems as well as new installations.

Faster Installation

Everything you need for installation is in the box, including simple drilling templates.

Easy Control and Maintenance

Sensepoint XCL's smartphone interface makes for much faster calibration, configuration and bump tests. Inspecting the status and settings of individual Sensepoint XCL detectors is simple. Use the mobile app to:

• Read gas concentrations in real-time
• Reconfigure settings
• Check unit histories

Automated Reporting

Increase the efficiency of your operations and reduce administration time. The app and Sensepoint XCL provides easy access to diagnostic information and generates calibration reports at the touch of a screen.

Compatible System Controller

Touchpoint Plus is the perfect complement to Sensepoint XCL, providing an intuitive, easy to operate gas detection solution to meet the needs of your business.

Visual Integration

Sensepoint XCL is designed with the needs of building architects in mind. Clean aesthetics and a choice of colors mean that the detector is ideal for public spaces like lobbies and retail environments.

Typical Applications

• Kitchens and food processing
• Manufacturing facilities and factories
• Hospitals
• Retail sites
• Transportation and parking
• Laboratories
• Hotel and leisure
• Apartments, accommodation blocks and condominiums

Accessories

• Calibration cap / flow housing
• Duct mount kit for round or flat profile ducts

FEATURES & BENEFITS

• Choose from a range of mA or Modbus output versions for flexible system design to meet the customers requirements.
• Selectable source or sink current for analog output enables one detector to be suitable for both system configurations.
• Optional relay output for external control systems or alarming devices enables easy integration and local indication.
• The ingress protection of IP65 allows units to be mounted in wash down areas.
• Multi-color visual indicator to show status makes it easier to know the detector status immediately and identify detectors that require attention or are warning of danger.
• Gassing port for easier bump test of units installed in inaccessible locations. No need to purchase a separate accessory and thus saves money.
• Manage the detector without making a physical connection. Remove the need for physical access to hard-to-reach devices.
• Simplified maintenance with familiar smartphone technology saves money and time.

2108B2001N Optima Plus Gas Detector, HYDROCARB ATEX by Honeywell Analytics

Market leading point infrared Hydrocarbon gas detector offering proven performance and sensitivity

With over 40 years experience in the design, manufacture, installation and maintenance of point infrared gas detection, Honeywell Analytics currently has a Worldwide installed base of over 100,000 infrared point Hydrocarbon gas detectors in a wide spectrum of applications from light industrial to the most demanding of offshore petrochemical environments.

Searchpoint Optima Plus is an infrared point Hydrocarbon gas detector certified for use in potentially explosive atmospheres. The unit's infrared detection principle offers the fastest speed of response and fail-to-safe operation, ensuring that your plant is compliant, your personnel are protected and your production process can deliver maximum uptime. Reduced routine maintenance, when compared with conventional electro-catalytic based gas detectors, provides low ongoing cost of ownership. The development of advanced internal fault diagnostics and false alarm rejection algorithms ensures that Searchpoint Optima Plus delivers the highest level of operational integrity.

Typical applications include environments that may suffer from the presence of catalytic bead poisons or inhibitors, or where there are harsh environmental conditions forcing increased time between routine maintenance, for example; offshore oil and gas platforms, floating production storage and offloading (FPSO) vessels, tankers, onshore oil and gas terminals, refineries, LNG / LPG bottling plants, gas compressor / metering stations, gas turbine power plants, refineries, solvent printing and coating plants.

Over 100 gas and vapour calibrations are available. For a list of detectable gases and vapours, please contact our Customer Support team or your local distributor.

Why Infrared?

• Failsafe operation
• Fast speed of response
• Reduced routine maintenance
• Immune to catalytic poisons
• Long operating life
• Works in inert atmospheres

Why Searchpoint Optima Plus is the right choice...

• Experience gained from over 100,000 units installed worldwide
• Improved reliability
• Optional HART® over 4-20mA output
• Can detect a wide range of hydrocarbon gases including solvents
• Increased reliability with no moving parts
• Increased stability from self compensating optics
• Immune to long term component drift
• Remote functional gas test facility
• Certified for North American and European Hazardous areas
• Increased false alarm rejection
• Increased uptime with contaminated optics warning
• Dynamic Heating Control ensures condensation free optics
• No undetected failures
• Improved diagnostics
• Integral event logging
• Reduced power consumption
• Certified to many hazardous area classification schemes including: European (ATEX), UL, CSA, IECEx and more

1309A0057 E3Point Gas Monitor with Remote Sensor, Nitrogen dioxide (NO2) by Honeywell Analytics

Toxic/combustible gas monitor that makes a commercial operation run more intelligently to protect people, property and the bottom line.

Product Overview:

E3Point is capable of detecting the widest range of toxic and combustible gases found in commercial building spaces and outbuildings, including CO, NO2, O2, H2, H2S, CH4 and C3H8. It can be used as a standalone unit with single or dual-gas detection (i.e. using a remote sensor) or deployed as a networkable device (interoperable with BACnet, Modbus or other Building Automation System): E3Point also functions with existing controller-based gas monitoring systems and wired-wireless gas monitoring system components.

E3Point uses Demand Control Ventilation—through relays, Building Automation System (BAS) or controller—to increase energy savings, extend fan life and align with green building best practices. In its network configuration, E3Point also optimizes HVAC, fire/smoke, surveillance and other building systems performance.

Intelligent product design reduces the unit's cost of ownership while increasing flexibility of application. Smart sensors are pre-calibrated, auto-configure upon set-up and operate continuously on patented Reflex© technology which continuously monitors sensor cell condition and alerts user to fault status. The plug-n-play sensor cartridge, user-friendly menu and wiring options simplify installation and maintenance, and reduce the cost of gas monitoring over the life of the unit.

Flexible Operation:

• Comes in standalone, standalone with remote (dual gas mode) or network versions
• Connects to analog or digital systems
• Works with virtually any BAS including BACnet and Modbus
• Connects to wired or wireless system (via 301CW wireless controller)
• Wall or duct mount
• Factory-calibrated cartridges

Cost Effective:

• Saves energy through Demand Control Ventilation (DCV)
• Simplifies installation/maintenance through plug-n-play sensor
• Remote sensor option provides dual gas monitoring (standalone version only)
• Optimizes BAS, fire, ventilation and other security systems

Versatile Communications:

• Works through BAS to improve fault diagnostics and collect data on gas concentration levels, sensor condition, etc.
• Couple with 301C to log data and daisy-chain up to 96 E3Point units

Advanced Sensing Technology:

• Detects CO, NO2, O2, H2, H2S, CH4, C3H8
• Advanced electrochemical (for toxic gases)and catalytic bead (for combustible gases) sensor performance
• Uses patented Reflex® and smart cartridge technologies

Electrical Certifications:

• US (ANSI/UL 61010-1)
• Canada (CSA C22.2 No. 61010-1)

Features & Benefits:

• Standalone, standalone with remote (dual gas mode) or network versions available
• Saves energy through Demand Control Ventilation

Quick Specs:

• Complete toxic and combustible gas detection system with onboard sounder
• Available in single point or dual gas options
• Analog 4-20 mA or Digital outputs (Bacnet, Modbus, and Lonworks)

1309A0036 E3Point Gas Monitor, Oxygen (O2); -40° to 50°C (-40° to 122°F) by Honeywell Analytics

Toxic/combustible gas monitor that makes a commercial operation run more intelligently to protect people, property and the bottom line.

Product Overview:

E3Point is capable of detecting the widest range of toxic and combustible gases found in commercial building spaces and outbuildings, including CO, NO2, O2, H2, H2S, CH4 and C3H8. It can be used as a standalone unit with single or dual-gas detection (i.e. using a remote sensor) or deployed as a networkable device (interoperable with BACnet, Modbus or other Building Automation System): E3Point also functions with existing controller-based gas monitoring systems and wired-wireless gas monitoring system components.

E3Point uses Demand Control Ventilation—through relays, Building Automation System (BAS) or controller—to increase energy savings, extend fan life and align with green building best practices. In its network configuration, E3Point also optimizes HVAC, fire/smoke, surveillance and other building systems performance.

Intelligent product design reduces the unit's cost of ownership while increasing flexibility of application. Smart sensors are pre-calibrated, auto-configure upon set-up and operate continuously on patented Reflex© technology which continuously monitors sensor cell condition and alerts user to fault status. The plug-n-play sensor cartridge, user-friendly menu and wiring options simplify installation and maintenance, and reduce the cost of gas monitoring over the life of the unit.

Flexible Operation:

• Comes in standalone, standalone with remote (dual gas mode) or network versions
• Connects to analog or digital systems
• Works with virtually any BAS including BACnet and Modbus
• Connects to wired or wireless system (via 301CW wireless controller)
• Wall or duct mount
• Factory-calibrated cartridges

Cost Effective:

• Saves energy through Demand Control Ventilation (DCV)
• Simplifies installation/maintenance through plug-n-play sensor
• Remote sensor option provides dual gas monitoring (standalone version only)
• Optimizes BAS, fire, ventilation and other security systems

Versatile Communications:

• Works through BAS to improve fault diagnostics and collect data on gas concentration levels, sensor condition, etc.
• Couple with 301C to log data and daisy-chain up to 96 E3Point units

Advanced Sensing Technology:

• Detects CO, NO2, O2, H2, H2S, CH4, C3H8
• Advanced electrochemical (for toxic gases)and catalytic bead (for combustible gases) sensor performance
• Uses patented Reflex® and smart cartridge technologies

Electrical Certifications:

• US (ANSI/UL 61010-1)
• Canada (CSA C22.2 No. 61010-1)

Features & Benefits:

• Standalone, standalone with remote (dual gas mode) or network versions available
• Saves energy through Demand Control Ventilation

Quick Specs:

• Complete toxic and combustible gas detection system with onboard sounder
• Available in single point or dual gas options
• Analog 4-20 mA or Digital outputs (Bacnet, Modbus, and Lonworks)

1309A0041 E3Point Gas Monitor, Propane (C3H8); -40° to 50°C (-40° to 122°F) by Honeywell Analytics

Toxic/combustible gas monitor that makes a commercial operation run more intelligently to protect people, property and the bottom line.

Product Overview:

E3Point is capable of detecting the widest range of toxic and combustible gases found in commercial building spaces and outbuildings, including CO, NO2, O2, H2, H2S, CH4 and C3H8. It can be used as a standalone unit with single or dual-gas detection (i.e. using a remote sensor) or deployed as a networkable device (interoperable with BACnet, Modbus or other Building Automation System): E3Point also functions with existing controller-based gas monitoring systems and wired-wireless gas monitoring system components.

E3Point uses Demand Control Ventilation—through relays, Building Automation System (BAS) or controller—to increase energy savings, extend fan life and align with green building best practices. In its network configuration, E3Point also optimizes HVAC, fire/smoke, surveillance and other building systems performance.

Intelligent product design reduces the unit's cost of ownership while increasing flexibility of application. Smart sensors are pre-calibrated, auto-configure upon set-up and operate continuously on patented Reflex© technology which continuously monitors sensor cell condition and alerts user to fault status. The plug-n-play sensor cartridge, user-friendly menu and wiring options simplify installation and maintenance, and reduce the cost of gas monitoring over the life of the unit.

Flexible Operation:

• Comes in standalone, standalone with remote (dual gas mode) or network versions
• Connects to analog or digital systems
• Works with virtually any BAS including BACnet and Modbus
• Connects to wired or wireless system (via 301CW wireless controller)
• Wall or duct mount
• Factory-calibrated cartridges

Cost Effective:

• Saves energy through Demand Control Ventilation (DCV)
• Simplifies installation/maintenance through plug-n-play sensor
• Remote sensor option provides dual gas monitoring (standalone version only)
• Optimizes BAS, fire, ventilation and other security systems

Versatile Communications:

• Works through BAS to improve fault diagnostics and collect data on gas concentration levels, sensor condition, etc.
• Couple with 301C to log data and daisy-chain up to 96 E3Point units

Advanced Sensing Technology:

• Detects CO, NO2, O2, H2, H2S, CH4, C3H8
• Advanced electrochemical (for toxic gases)and catalytic bead (for combustible gases) sensor performance
• Uses patented Reflex® and smart cartridge technologies

Electrical Certifications:

• US (ANSI/UL 61010-1)
• Canada (CSA C22.2 No. 61010-1)

Features & Benefits:

• Standalone, standalone with remote (dual gas mode) or network versions available
• Saves energy through Demand Control Ventilation

Quick Specs:

• Complete toxic and combustible gas detection system with onboard sounder
• Available in single point or dual gas options
• Analog 4-20 mA or Digital outputs (Bacnet, Modbus, and Lonworks)

1309A0038 E3Point Gas Monitor, Carbon monoxide (CO); -20° to 50°C (-4° to 122°F) by Honeywell Analytics

Toxic/combustible gas monitor that makes a commercial operation run more intelligently to protect people, property and the bottom line.

Product Overview:

E3Point is capable of detecting the widest range of toxic and combustible gases found in commercial building spaces and outbuildings, including CO, NO2, O2, H2, H2S, CH4 and C3H8. It can be used as a standalone unit with single or dual-gas detection (i.e. using a remote sensor) or deployed as a networkable device (interoperable with BACnet, Modbus or other Building Automation System): E3Point also functions with existing controller-based gas monitoring systems and wired-wireless gas monitoring system components.

E3Point uses Demand Control Ventilation—through relays, Building Automation System (BAS) or controller—to increase energy savings, extend fan life and align with green building best practices. In its network configuration, E3Point also optimizes HVAC, fire/smoke, surveillance and other building systems performance.

Intelligent product design reduces the unit's cost of ownership while increasing flexibility of application. Smart sensors are pre-calibrated, auto-configure upon set-up and operate continuously on patented Reflex© technology which continuously monitors sensor cell condition and alerts user to fault status. The plug-n-play sensor cartridge, user-friendly menu and wiring options simplify installation and maintenance, and reduce the cost of gas monitoring over the life of the unit.

Flexible Operation:

• Comes in standalone, standalone with remote (dual gas mode) or network versions
• Connects to analog or digital systems
• Works with virtually any BAS including BACnet and Modbus
• Connects to wired or wireless system (via 301CW wireless controller)
• Wall or duct mount
• Factory-calibrated cartridges

Cost Effective:

• Saves energy through Demand Control Ventilation (DCV)
• Simplifies installation/maintenance through plug-n-play sensor
• Remote sensor option provides dual gas monitoring (standalone version only)
• Optimizes BAS, fire, ventilation and other security systems

Versatile Communications:

• Works through BAS to improve fault diagnostics and collect data on gas concentration levels, sensor condition, etc.
• Couple with 301C to log data and daisy-chain up to 96 E3Point units

Advanced Sensing Technology:

• Detects CO, NO2, O2, H2, H2S, CH4, C3H8
• Advanced electrochemical (for toxic gases)and catalytic bead (for combustible gases) sensor performance
• Uses patented Reflex® and smart cartridge technologies

Electrical Certifications:

• US (ANSI/UL 61010-1)
• Canada (CSA C22.2 No. 61010-1)

Features & Benefits:

• Standalone, standalone with remote (dual gas mode) or network versions available
• Saves energy through Demand Control Ventilation

Quick Specs:

• Complete toxic and combustible gas detection system with onboard sounder
• Available in single point or dual gas options
• Analog 4-20 mA or Digital outputs (Bacnet, Modbus, and Lonworks)

711305 Chemcassette Tape, Nitrogen Dioxide (3) by Honeywell Analytics

Chemcassette® is the unique trademarked name for a calibration free toxic gas detection method that uses an optical scanning system to detect the presence of gas by a colour change on the specially chemically impregnated paper tape. Chemcassette® technology is highly specific and reacts extremely fast to the presence of parts per billion (ppb) levels of many hazardous gases. Over 200,000 points of gas detection are currently maintained by the Chemcassette® sensing technology at any given time around the World in some of the most critical safety applications possible.

Each Chemcassette® is manufactured to traceable ISO 9000 manufacturing standards by a world class team of highly trained chemists and each batch is calibrated with ultra pure gas that is traceable to nationally accepted standards. This means that the end user does not have to provide calibration facilities themselves thereby saving cost and reducing risks to their own staff.

Efficient high volume manufacturing techniques means that there is always available Chemcassette® in stock that can be shipped anywhere in the World so that our customers are never left without adequate safety cover. Application support with expert gas detection chemists is available by phone and e-mail and is supported with many years of technical application notes and help to diagnose common support issues.

Should there be any concern regarding the performance of an individual Chemcassette®, a free of charge evaluation will be performed to trouble shoot the observed scenario using the award winning quality management system "Customer Discrepancy Report" CDR. Every CDR completed by a customer is guaranteed a full response and the outcome is reported directly back to the end user to ensure a complete resolution process.

Each Chemcassette® is backed with a full warranty and we have over 20 years of experience regarding the quality control of our proven sensing technology.

Additional Features and Benefits:

• Visible proof of a gas release event
• Greater sensitivity (detection down to parts per billion levels)
• Superior selectivity (less cross-interference with other gases)
• Fast response time
• Low false alarm occurrence
• Stability (consistent, repeatable operation)
• No calibration required
• Easy to use
• Available in fixed and portable instrumentation

Features & Benefits

• Visible proof of a gas release event
• Fast response time
• Low false alarm occurrence

Quick Specs

• Greater sensitivity (detection down to parts per billion levels)
• Superior selectivity (less cross-interference with other gases)
• Stability (consistent, repeatable operation)

FS24X-211-22-1 FS24X QuadBand™ IR3+ Fire and Flame Detector, 316 Stainless Steel Encl., (2) 3/4 in. NPT entries FM & ATEX approved by Honeywell Analytics

Fire Sentry FS24X is a quantum leap in flame detection with its sophisticated software and detection technology.

The Fire Sentry FS24X is the latest generation high technology Multi-Spectrum Triple IR (IR/IR/IR/Visible) Flame Detector, which is part of our FSX family of advanced technology Electro-Optical fire detectors. Using our patented* WideBand IR™, WideBand 4.3 micron IR™, and Visible detection technology, the Fire Sentry FS24X is a quantum leap in flame detection. Sophisticated software algorithms and dual microprocessors ensure that the Fire Sentry FS24X has the highest flame detection performance combined with optimal false alarm rejection.

The WideBand IR™ Infrared technology using high-speed solid-state Quantum sensors allows detection of all types of fires, hydrocarbon and non-hydrocarbon, in all weather conditions. If the detector's signal is blocked by ordinary window glass, the patented WideBand IR sensors will still alarm to the fire albeit at a reduced sensitivity and slower response time.

Dual microprocessors provide a high level of fail-safe operation combined with fast and reliable performance. The master microprocessor performs high-speed digital sampling and signal-processing calculations, while the slave microprocessor handles various sensor data, performs communications, self-diagnostics and provides interface versatility and additional memory for storing Event Log and FirePic™ data.

The Fire Sentry FSX family of detectors feature our patented* FirePic data storage and information retrieval facility. FirePic™ records pre-fire data, which can be recovered from the Detector's non-volatile flash memory for post fire analysis and postulation of the fire cause. Additionally, unique Real-Time Graphing (RTG™) allows viewing of the data which the Detector actually sees. A combination of outputs makes the Fire Sentry FS24X a truly versatile detector for today's demanding industrial requirements.

The Fire Sentry FS24X detector has a detection range greater than 200 feet (Very High Sensitivity setting) for the detection of a one square-foot Heptane reference fire and has a cone of vision far greater in volumetric coverage than any other Multi-Spectrum IR Detector. This means fewer Detectors can be used as compared to other manufacturers' Detectors.

Features

• Patented* WideBand IR™ technology
• Patented* Electronic Frequency Analysis™
• Visible sensor for optimum false alarm rejection
• Selectable detection sensitivities
• Field-of-View: 110° cone-of-vision (90° cone-of-vision model also available)
• Dual microprocessors for reliable performance
• Real-time clock for accurate time dating of events
• FirePic™ - pre-fire event data storage
• Event log with date and time stamp
• RS-485 ModBus communication
• Non-Isolated 4-20 mA Analog output (sink or source)
• Alarm, Fault and Fire Verification relays
• Automatic optical path and electronic self-test
• Patented* Electronics Module for components protection with easy plug-in terminations and field installation
• Two 3/4" NPT conduit entries
• Low power consumption
• High RFI and EMI immunity
• FM, ATEX, CE mark approvals
• CU-TR approved
• INMETRO approved
• Meets SIL 2 requirements
• Certified to EN54-10:2002 (FS24X-9) option
• FM 3260 Performance

Benefits

• Detects hydrocarbon and non-hydrocarbon fuel fires in all environmental conditions
• User selectable outputs
• Wide operating temperature range
• Optimal false alarm rejection
• Minimal maintenance for trouble-free operation
• PC software and Interface Module (FSIM) for fault diagnostics, real-time graphics (RTGs), and downloading of FirePics™ and event log
• Suitable for a wide variety of applications
• Easy electronics module replacement
• Test lamps for manual testing

Applications

• Refineries and oil production facilities
• Off-Shore platforms
• Turbine/Compressor enclosures
• Oil and gas pipelines and pumping stations
• LNG/LPG loading and unloading facilities
• Natural Gas and CNG plants
• Ethanol, Methanol, and IPA production and storage
• Crude oil and gasoline storage and tank farms
• Aircraft hangars
• Paint and solvent storage
• Chemical production, storage, and loading facilities
• Power plants

FS24X-912-24-4 FS24X QuadBand™ IR3+ Fire and Flame Detector, 316 Stainless Steel Encl., (2) M25 entries INMETRO approved with FSX-A014R Optional Registered HART Module for FS24X Detectors Factory installed by Honeywell Analytics

Fire Sentry FS24X is a quantum leap in flame detection with its sophisticated software and detection technology.

The Fire Sentry FS24X is the latest generation high technology Multi-Spectrum Triple IR (IR/IR/IR/Visible) Flame Detector, which is part of our FSX family of advanced technology Electro-Optical fire detectors. Using our patented* WideBand IR™, WideBand 4.3 micron IR™, and Visible detection technology, the Fire Sentry FS24X is a quantum leap in flame detection. Sophisticated software algorithms and dual microprocessors ensure that the Fire Sentry FS24X has the highest flame detection performance combined with optimal false alarm rejection.

The WideBand IR™ Infrared technology using high-speed solid-state Quantum sensors allows detection of all types of fires, hydrocarbon and non-hydrocarbon, in all weather conditions. If the detector's signal is blocked by ordinary window glass, the patented WideBand IR sensors will still alarm to the fire albeit at a reduced sensitivity and slower response time.

Dual microprocessors provide a high level of fail-safe operation combined with fast and reliable performance. The master microprocessor performs high-speed digital sampling and signal-processing calculations, while the slave microprocessor handles various sensor data, performs communications, self-diagnostics and provides interface versatility and additional memory for storing Event Log and FirePic™ data.

The Fire Sentry FSX family of detectors feature our patented* FirePic data storage and information retrieval facility. FirePic™ records pre-fire data, which can be recovered from the Detector's non-volatile flash memory for post fire analysis and postulation of the fire cause. Additionally, unique Real-Time Graphing (RTG™) allows viewing of the data which the Detector actually sees. A combination of outputs makes the Fire Sentry FS24X a truly versatile detector for today's demanding industrial requirements.

The Fire Sentry FS24X detector has a detection range greater than 200 feet (Very High Sensitivity setting) for the detection of a one square-foot Heptane reference fire and has a cone of vision far greater in volumetric coverage than any other Multi-Spectrum IR Detector. This means fewer Detectors can be used as compared to other manufacturers' Detectors.

Features

• Patented* WideBand IR™ technology
• Patented* Electronic Frequency Analysis™
• Visible sensor for optimum false alarm rejection
• Selectable detection sensitivities
• Field-of-View: 110° cone-of-vision (90° cone-of-vision model also available)
• Dual microprocessors for reliable performance
• Real-time clock for accurate time dating of events
• FirePic™ - pre-fire event data storage
• Event log with date and time stamp
• RS-485 ModBus communication
• Non-Isolated 4-20 mA Analog output (sink or source)
• Alarm, Fault and Fire Verification relays
• Automatic optical path and electronic self-test
• Patented* Electronics Module for components protection with easy plug-in terminations and field installation
• Two 3/4" NPT conduit entries
• Low power consumption
• High RFI and EMI immunity
• FM, ATEX, CE mark approvals
• CU-TR approved
• INMETRO approved
• Meets SIL 2 requirements
• Certified to EN54-10:2002 (FS24X-9) option
• FM 3260 Performance

Benefits

• Detects hydrocarbon and non-hydrocarbon fuel fires in all environmental conditions
• User selectable outputs
• Wide operating temperature range
• Optimal false alarm rejection
• Minimal maintenance for trouble-free operation
• PC software and Interface Module (FSIM) for fault diagnostics, real-time graphics (RTGs), and downloading of FirePics™ and event log
• Suitable for a wide variety of applications
• Easy electronics module replacement
• Test lamps for manual testing

Applications

• Refineries and oil production facilities
• Off-Shore platforms
• Turbine/Compressor enclosures
• Oil and gas pipelines and pumping stations
• LNG/LPG loading and unloading facilities
• Natural Gas and CNG plants
• Ethanol, Methanol, and IPA production and storage
• Crude oil and gasoline storage and tank farms
• Aircraft hangars
• Paint and solvent storage
• Chemical production, storage, and loading facilities
• Power plants

SPLCA1BMXCXNZZ Sensepoint XCL Fixed Gas Detector, Bluetooth Connection, NH3 100ppm, Modbus, Charcoal by Honeywell Analytics

Sensepoint XCL is a fixed point gas leak detector that is designed to meet the needs of commercial and light industrial applications. With over 50 years experience in gas leak detection, Honeywell offers a flexible range of highly-reliable sensing devices to meet those needs.

• Quicker installation
• Rapid configuration
• Simple to operate
• Straightforward to maintain

Honeywell innovation enables customers to pair the gas detector with their mobile phone, and then use an app to perform many tasks related to installation, commissioning and maintenance.

Flexible Output Options

Sensepoint XCL is available with either mA loop analog output or Modbus RTU with the option for relays on both. The result is a flexible solution that can easily be incorporated into legacy systems as well as new installations.

Faster Installation

Everything you need for installation is in the box, including simple drilling templates.

Easy Control and Maintenance

Sensepoint XCL's smartphone interface makes for much faster calibration, configuration and bump tests. Inspecting the status and settings of individual Sensepoint XCL detectors is simple. Use the mobile app to:

• Read gas concentrations in real-time
• Reconfigure settings
• Check unit histories

Automated Reporting

Increase the efficiency of your operations and reduce administration time. The app and Sensepoint XCL provides easy access to diagnostic information and generates calibration reports at the touch of a screen.

Compatible System Controller

Touchpoint Plus is the perfect complement to Sensepoint XCL, providing an intuitive, easy to operate gas detection solution to meet the needs of your business.

Visual Integration

Sensepoint XCL is designed with the needs of building architects in mind. Clean aesthetics and a choice of colors mean that the detector is ideal for public spaces like lobbies and retail environments.

Typical Applications

• Kitchens and food processing
• Manufacturing facilities and factories
• Hospitals
• Retail sites
• Transportation and parking
• Laboratories
• Hotel and leisure
• Apartments, accommodation blocks and condominiums

Accessories

• Calibration cap / flow housing
• Duct mount kit for round or flat profile ducts

FEATURES & BENEFITS

• Choose from a range of mA or Modbus output versions for flexible system design to meet the customers requirements.
• Selectable source or sink current for analog output enables one detector to be suitable for both system configurations.
• Optional relay output for external control systems or alarming devices enables easy integration and local indication.
• The ingress protection of IP65 allows units to be mounted in wash down areas.
• Multi-color visual indicator to show status makes it easier to know the detector status immediately and identify detectors that require attention or are warning of danger.
• Gassing port for easier bump test of units installed in inaccessible locations. No need to purchase a separate accessory and thus saves money.
• Manage the detector without making a physical connection. Remove the need for physical access to hard-to-reach devices.
• Simplified maintenance with familiar smartphone technology saves money and time.

2108N4100N Optima Plus Gas Detector, hydrocarbon version, 4 to 20mA output, UL/INMETRO, 3/4" NPT thread spigot, electro polished 316SS, includes polyester mesh dust barrier, nylon weather protection housing and LNP Faradex deluge/sunshade by Honeywell Analytics

Market leading point infrared Hydrocarbon gas detector offering proven performance and sensitivity

With over 40 years experience in the design, manufacture, installation and maintenance of point infrared gas detection, Honeywell Analytics currently has a Worldwide installed base of over 100,000 infrared point Hydrocarbon gas detectors in a wide spectrum of applications from light industrial to the most demanding of offshore petrochemical environments.

Searchpoint Optima Plus is an infrared point Hydrocarbon gas detector certified for use in potentially explosive atmospheres. The unit's infrared detection principle offers the fastest speed of response and fail-to-safe operation, ensuring that your plant is compliant, your personnel are protected and your production process can deliver maximum uptime. Reduced routine maintenance, when compared with conventional electro-catalytic based gas detectors, provides low ongoing cost of ownership. The development of advanced internal fault diagnostics and false alarm rejection algorithms ensures that Searchpoint Optima Plus delivers the highest level of operational integrity.

Typical applications include environments that may suffer from the presence of catalytic bead poisons or inhibitors, or where there are harsh environmental conditions forcing increased time between routine maintenance, for example; offshore oil and gas platforms, floating production storage and offloading (FPSO) vessels, tankers, onshore oil and gas terminals, refineries, LNG / LPG bottling plants, gas compressor / metering stations, gas turbine power plants, refineries, solvent printing and coating plants.

Over 100 gas and vapour calibrations are available. For a list of detectable gases and vapours, please contact our Customer Support team or your local distributor.

Why Infrared?

• Failsafe operation
• Fast speed of response
• Reduced routine maintenance
• Immune to catalytic poisons
• Long operating life
• Works in inert atmospheres

Why Searchpoint Optima Plus is the right choice...

• Experience gained from over 100,000 units installed worldwide
• Improved reliability
• Optional HART® over 4-20mA output
• Can detect a wide range of hydrocarbon gases including solvents
• Increased reliability with no moving parts
• Increased stability from self compensating optics
• Immune to long term component drift
• Remote functional gas test facility
• Certified for North American and European Hazardous areas
• Increased false alarm rejection
• Increased uptime with contaminated optics warning
• Dynamic Heating Control ensures condensation free optics
• No undetected failures
• Improved diagnostics
• Integral event logging
• Reduced power consumption
• Certified to many hazardous area classification schemes including: European (ATEX), UL, CSA, IECEx and more

1309A0042 E3Point Gas Monitor without Sensor, Wall Mount, Analog, 24VAC/VDC by Honeywell Analytics

Toxic/combustible gas monitor that makes a commercial operation run more intelligently to protect people, property and the bottom line.

Product Overview:

E3Point is capable of detecting the widest range of toxic and combustible gases found in commercial building spaces and outbuildings, including CO, NO2, O2, H2, H2S, CH4 and C3H8. It can be used as a standalone unit with single or dual-gas detection (i.e. using a remote sensor) or deployed as a networkable device (interoperable with BACnet, Modbus or other Building Automation System): E3Point also functions with existing controller-based gas monitoring systems and wired-wireless gas monitoring system components.

E3Point uses Demand Control Ventilation—through relays, Building Automation System (BAS) or controller—to increase energy savings, extend fan life and align with green building best practices. In its network configuration, E3Point also optimizes HVAC, fire/smoke, surveillance and other building systems performance.

Intelligent product design reduces the unit's cost of ownership while increasing flexibility of application. Smart sensors are pre-calibrated, auto-configure upon set-up and operate continuously on patented Reflex© technology which continuously monitors sensor cell condition and alerts user to fault status. The plug-n-play sensor cartridge, user-friendly menu and wiring options simplify installation and maintenance, and reduce the cost of gas monitoring over the life of the unit.

Flexible Operation:

• Comes in standalone, standalone with remote (dual gas mode) or network versions
• Connects to analog or digital systems
• Works with virtually any BAS including BACnet and Modbus
• Connects to wired or wireless system (via 301CW wireless controller)
• Wall or duct mount
• Factory-calibrated cartridges

Cost Effective:

• Saves energy through Demand Control Ventilation (DCV)
• Simplifies installation/maintenance through plug-n-play sensor
• Remote sensor option provides dual gas monitoring (standalone version only)
• Optimizes BAS, fire, ventilation and other security systems

Versatile Communications:

• Works through BAS to improve fault diagnostics and collect data on gas concentration levels, sensor condition, etc.
• Couple with 301C to log data and daisy-chain up to 96 E3Point units

Advanced Sensing Technology:

• Detects CO, NO2, O2, H2, H2S, CH4, C3H8
• Advanced electrochemical (for toxic gases)and catalytic bead (for combustible gases) sensor performance
• Uses patented Reflex® and smart cartridge technologies

Electrical Certifications:

• US (ANSI/UL 61010-1)
• Canada (CSA C22.2 No. 61010-1)

Features & Benefits:

• Standalone, standalone with remote (dual gas mode) or network versions available
• Saves energy through Demand Control Ventilation

Quick Specs:

• Complete toxic and combustible gas detection system with onboard sounder
• Available in single point or dual gas options
• Analog 4-20 mA or Digital outputs (Bacnet, Modbus, and Lonworks)