Test and Measurement

6230MKA pH/mV/Temp. Microprocessor Handheld Meter Kit by Jenco

pH/mV/Temp. microprocessor handheld meter in splash proof case with 3 point calibration, 40 memory storage, RS-232-C IBM compatible communication interface and BNC, pH/ORP connector with 8-pin DIN ATC connector. AC/DC power. CE Approved.

Includes:

• 6230M pH/mV/Temp. Microprocessor Handheld Meter
• 6230A-ST Stainless Steel Temperature Probe

• 3 point calibration
• 40 memory storage
• Power down memories
• Electrode offset recognition
• Electrode slope recognition
• Built in buffer temp. coefficients
• ATC
• RS-232c output
• CE approved
• Splash resistant/watertight case
• Battery/ac adaptor
• High 50/60hz noise rejection
• UL approved ac line adaptor
• Aconventional 9v battery
• Highly reliable mechanical touch keys with audio feedback

275 Clamp-On Tester with True RMS Digital Multimeter and 11,000 Count Display by Test Products International

Clamp-On Tester with True RMS Digital Multimeter & 11,000 Count Display. The new TPI 275 with slim jaw and body is ideal for cramped work areas and crowded electrical panels.

The slim design 275 is a hand-held, autoranging clamp-on DMM. Extra large numerals, min/max, capacitance, DC microamps and duty cycle are just a few of the features of the 275. An affordable choice, the 275 offers measurements in all basic electrical functions with additional advanced features like non-contact voltage.

Features:

• True RMS
• 11,000 count display
• Up to 400 amps AC/DC
• Auto & Manual Ranging
• Data Hold
• Low Battery Indicator
• Over Range Indication ("OL")
• Peak Hold
• Min/Max
• Relative Mode
• Hi Voltage Indicator(>30V AC/DC)
• Non-contact voltage detection
• Auto Power Off after 30 minutes
• Separate Battery Compartment
• Low Ohm Range (110Ω)
• Amps AC Resolution: 0.01A
• VDC/VAC Resolution: 0.01mV
• DCiA measurement (0.01μA resolution)
• Temperature measurement

Applications:

• Measure DC amperage of motor drive units
• Measure flame safety control current
• Test run and start capacitors and motors
• Measure motor run current and capture peak motor start up amperage
• Measure heat anticipator current
• Determine thermocouple voltage
• Test line and control voltages
• Measure heating element resistance
• Measure air temperature in ducts
• Test for the presence of voltage in circuits without contacting the circuit
• Measure temperature differential using relative mode

The 275 comes complete with the following accessories:

• Carrying Pouch
• Test Lead Set
• Temperature Probe
• Instruction Manual
• Battery & Fuse

0572 1764 176 T4 4-Channel Temperature Logger with 4 External Thermocouple Connections (Type T, K, J) by Testo

You can measure and document flow and return temperatures with the testo 176 T4 at 4 different places, for example at the distributor og an underfloor heating system, in order to test its functionality. The requirements of a many different applications can be fulfilled using a broad range of connectable thermocouple probes (Type K, Type T, Type J).

• Large memory for 2 million measurement values - large, easily legible display
• up to 8 years battery life
• Standard battery (AA) replaceable by user
• Scope of delivery: Data logger testo 176 T4 incl. wallholder, lock, batteries, calibration certificate and instruction manual

6173R Large LCD Benchtop pH/mV/Temp Meter with RS-232 Interface by Jenco

pH/mV/Temp benchtop meter with a very large LCD display for ease of use. Features a splash proof and rugged case ideal for schools and universities. Features EEF, Electrode Efficiency Function, multiple buffers 4.00, 4.01, 6.86, 7.00, 9.18 & 10.0 and automatic slope, buffer and electrode offset recognition. Has power down memory backup and works on 6 AA batteries or 115/230 V AC adapters. CE Approved & ISO 9001 Certified. RS-232C output.

• Larger LCD display
• Buffers recognition
• Electrode offset recognition
• Electrode slope recognition
• Built in buffer temp. coefficient
• Auto lock
• Touch keys with audio feedback
• Power down memory
• Battery/ac adaptor
• Low power consumption
• Battery low indicator
• Percentage of power supply display
• RS-232c output

Vibrio fischeri bacteria; shelf life is 18 months when stored at (-20C) - (-25C); on average one vial will provide enough reagent for 20-25 tests (depending on number of dilutions, test protocols, controls, etc.)

400563 4355 435-4 IAQ Kit with Memory by Testo

The ambient air conditions measuring instrument, for asssessing Indoor Air Quality and tuning and testing VAC systems, stands out on account of its efficient measurement process. The user-friendly measuring instrument has the right measurement engineering for every application and different flow speeds; for example, thermal probes, vane or Pitot tube measurement. Probe-controlled menus and selectable user profiles, e.g. for duct measurement or long-term measurement, ensure the user-friendliest operation possible. The new IAQ probe measures Indoor Air Quality by measuring the CO2 level, air moisture and air temperature. In addition, lux and comfort level probes can be connected to measure draught air. Clear analysis and archiving ensure convenient documentation. Temperature and humidity measurement is built-in in the new thermal probe. The special flow protocol professionally documents duct measurements. It is also possible to connect additional temperature and humidity probes. Readings from up to 3 temperature or humidity probes can be displayed in the measuring instrument; data transmission is by radio, i.e. wireless.

Kits includes:

• 0563 4354 - 435-4 with memory, software & integral differential pressure
• 0632 1535 - IAQ probe CO2, humidity, temperature
• 0554 0610 - Recharger with 4 NiMH rechargeable batteries
• 0635 2045 - 19" pitot tube
• 0554 0440 - Silicon hose for pressure probes (16' long)
• 0516 0435 - Deluxe service case

• Instrument memory for 10,000 readings
• PC software for analysis, filing and documentation of measurement data
• IAQ probe, lux probe and comfort level probe
• Thermal probes, vane measurement and built-in differential pressure probe probe for Pitot tube measurement
• Radio probe for temperature and humidity (optional)
• Protection class IP54

MC1K Handheld Radiation Alert Detector by SE International

The new ergonomic MC1K is a handheld survey meter using a built-in energy compensated GM detector. It detects gamma and x-rays up to 1000 mR/hr over 4 selectable ranges. A beep sounds and a count light flashes with each event detected.

0563 1550 550 Digital Manifold Kit with Bluetooth by Testo

The App integration via Bluetooth opens up new possibilities for efficient analysis and documentation. You can read the data on a Smartphone or Tablet, allowing for more work quickly and conveniently. In addition to this, the user can finalize and send the measurement report directly on site. The App allows the list of stored refrigerants to be updated, via the internet.

The more rugged housing includes a metal frame around the display which protects the new testo 550 from impact. Now with 60 refrigerant profiles and added functionality of leak tests, Testo manifolds are versatile enough to be the tool for every job.

Includes:

• 550 Digital Manifold with Bluetooth
• 0613 5505 - Two (2) 4.9 ft Clamp Probes (NTC)
• 0516 0012 - Hard carry case
• Certificate of Conformity

• Measures high side / low side pressures and temperatures
• Accurate, simultaneous super heat/subcooling in real time
• App integration via Bluetooth for monitoring and reporting
• 60 refrigerant profiles onboard
• Refrigerant updates in the instrument via App
• 2-way valve block with three connections, large, 2-line backlit display
• 5 year warranty with registration

0564 3004 95 300 Commercial / Industrial Analyzer Kit (O₂ & CO. Field upgradable for NO) by Testo

Truly smart combustion analysis: that is what the testo 300 stands for. The compact combustion analyzer is fully operated via the large touch display - you can see all the measuring values without scrolling. The scratch-resistant screen in embedded in a robust housing which remains reliable even in tough day-to-day working conditions. Menus for the most important measurements are already stored in the testo 300 and reliably guide you through the relevant application.

The combustion analyzer is not familiar with waiting times or start-up phases, it is immediately ready to go at the touch of a button in standby mode. Documentation is dealt with just as quickly with the testo 300, reports can be created and sent directly on site, with WiFi connection The testo 300 is available with a 2-year or 4-year warranty. There is also an optional NOx sensor available (with 2 year sensor warranty).

The O₂ sensor, is extremely durable and in Longlife models, an optional automatic dilution up to a maximum of 30,000 ppm CO protects the CO sensor.

• Large scratch-resistant 5" HD display with smart-touch operation and replaceable protective film
• Stored, intuitive menus for all relevant measurements
• 4 strong magnets with rubber coating for material friendly mounting
• Ready to measure at the touch of a button in standby mode
• Optional: extremely durable O₂ sensor and automatic dilution up to 30,000 ppm CO
• E-mailing of reports directly on site

Kit Includes:

• testo 300 O₂, CO, dilution 30.000 ppm, NO ready
• 12" probe, 1/4" diameter, 7' teflon hose assembly, t max=932°
• Spare part filters (10)
• testo 300 Hard Case
• easyheat PC analysis software

98768-63 Traceable® Blue-Steel Digital Timer with Calibration by Digi-Sense

With a stylish modern design, blue steel timer is an attractive addition to any lab. Automatic-Bounce back™ Memory feature returns timer to previously programmed setting at the touch of a key for quick repetitive timing. Memory is retained even after unit is turned off. Large keys and 1"H display make it easy to set time and read from a distance.

Traceable® Products have an individually-numbered Traceable® Certificate provided with each unit, that assures accuracy from our ISO/IEC 17025:2017(1750.01) calibration laboratory accredited by A2LA. It indicates traceability of measurements to the SI units through NIST or other recognized national measurement institutes (NMI) that are signatories to the CIPM Mutual Recognition Agreement. Each product goes through an intense vetting process before it can carry the Traceable name, thus saving you both time and money by not having to calibrate separately.

• Includes NIST-Traceable certificate from our A2LA accredited (1750.01) calibration laboratory
• Polished metal case and rubberized backing provides excellent durability

Includes

Magnetic back, flip-open stand, one 1.5 V LR44 battery, and NIST-traceable calibration certificate with data.

440 Single Input 1 MHz oscilloscope with True RMS DMM by Test Products International

The TPI 440 is a hand-held oscilloscope plus autoranging DMM. The instruments large, backlit LCD display shows a reading and waveform simultaneously. In addition to the standard functions of ACV, DCV, ACA, DCA, Ω, Diode Test and Continuity Buzzer; the 440 measures Frequency (Hz),Capacitance, Logic and Component test functions. The 440 also has RS232 output and software for interfacing with a PC is offered as an optional accessory.

Features:

• Auto Ranging 4,000 Count True RMS DMM: TPI s 440 has 9 measurement functions and 0.3% basic DC accuracy.
• 1 MHz Oscilloscope: View industrial power signals such as motor controls, UPS, switching power supplies, and PLC controls with detail and clarity.
• Trend Mode: Graph readings over a predetermined time period to check for surges or dropouts.
• Component Test: Check voltage-current signatures on resistors, capacitors, and semiconductors.
• Logic Test: Indicates transitions up to 2 MHz.
• Frequency Counter: Measure low frequency signals from 1Hz to 2 MHz and display duty cycle, pulse width and period.
• T-Base Button:Use feature to manually adjust sweep speed (time/division) to shrink or enlarge the viewable waveform for analysis.
• Continuous Autoset:Feature automatically determines the correct vertical and horizontal settings for optimum waveform viewing. Autoset provides hands free operation while moving between test points.
• PC/Printer Compatibility to RS-232C Port:Optional accessory A402 allows user to download data or waveforms to a PC for archiving, processing, and report generation. Perfect for extended monitoring. Eight waveform storage locations enables remote data acquisition for later viewing.

Applications:

• Industrial motor control: View start-up in rush currents, waveform symmetry, SCR trigger pulses, variable frequency drive signals, pulse width modulation, noise, miscellaneous AC/DC speed control signals, and synchronous motor and generator field excitation controls.
• Power quality: Define AC voltage wave shapes, current waveforms, machine start-up and power quality interference, and noise on industrial feeds and/or general noise.
• Battery testing: Measure voltage drops in Gel-Cell type batteries when connected in circuit. Measure stationary battery charger float and equalize voltages and individual cell voltages in DC backup power systems.
• Programmable logic controls: Read PLC input and output signals, control signals, signal conditioning circuits, communication lines and power supplies.
• NC/CNC machines: Check power quality, sensor outputs, control circuits, safety circuits, calibration and adjustments of components, relays and switches. Troubleshoot axis drives.
• Uninterruptable power supplies: Sense and monitor circuits, switching circuits, output waveforms and current waveforms.
• Audio: Locate noise spikes and voltage/current drops on all home/auto amplifiers, mixers, preamps, and paging system amplifiers.
• Video: Analyze horizontal and vertical scan rates, z-axis blanking, sync pulses and luminance.
• Industrial lighting controls:Troubleshoot SCR and Triac dimming controls and photo sensors. Measure lamp ballast voltages
• Factory automation: Robot control signals, machine vision, machine control and sensing circuits, calibration of positioning systems, analog controllers, and servo controls.
• Line conditioners: Detect noise and monitor waveform distortion
• Voltage regulators: Define noise and stability
• Inverters: Define waveform quality.
• Gaming Industry: Troubleshoot for component and capacitor degrading which causes noise to appear as periodic waveforms or rapid fluctuations. Most meters cannot catch these anomalies due to a slow sampling frequency. The 440 samples at 20 million times per second. This offers a visual graph of the voltage making it fast and simple for you to detect the noise.

716NA740 716N New Combustion Analyzer Kit by Test Products International

Features

• Built-in differential manometer with 0.001" H2O resolution
• Measure NO (Nitric Oxide), Calculate NOX
• Calculates combustion efficiency
• Data Logging with time and date stamp
• Will not shut off if 15 ppm CO is present for increased safety
• Communicate to a PC via the USB interface
• Optional A740 IR printer available for hard copies of test results
• Built-in differential thermometer
• Store function to save up to 10 readings
• Pump driven for fast response
• Push on fittings for fast and easy use
• Large easy to read backlit display
• Ten selectable fuels
• Optional Bluetooth interface

A740 Features

• Easy to use
• Battery operated
• Self test facility
• Adjustable contrast
• Manual paper feed
• Maximum transmitting distance 16"(45cm)

Includes

• 716N New Combustion Analyzer
• A740 IR Printer