Oakton Instruments

WD-35625-41 Economic 2-in-1 Food Safety IR Thermometer by Digi-Sense

A combination contact/noncontact thermometer for all food applications

Check critical food temperatures and monitor HACCP food safety zones with this combination contact/noncontact thermometer. LED s rapidly indicate if food temperature is in the bacterial growth safety zone. Green lights indicate safe temperatures below 40°F (4°C) and above 140°F (60°C). Red light indicates the HACCP danger zone between 40 to 140°F (4 to 60°C). The contact probe swings out for internal temperature checks, then folds in for storage. IR mode provides quick, noncontact surface measurements and stores maximum reading. Target illumination indicates target measurement area and is ideal for close working distances of 2 to 12 . Countdown timer with alarm monitors cooking and cooling intervals and HACCP exposure times set countdown timer to a maximum of 8 hours.

• Go/no-go LEDs provide quick check of HACCP food zones
• Sealed IP54 housing make for easy cleaning

WD-00653-89 8974 µS Conductivity/TDS Calibration Solution 500 mL (1-pint) Bottle by Oakton

Choose from economical 1-pint solution bottles or individually sealed Singles calibration pouches.

All OAKTON Conductivity/TDS calibration solutions are cross checked using different test methods, premixed, and ready to use.

OAKTON conductivity/TDS solution bottles are labeled with the name and CAS number for all ingredients to conform with Right-to-Know requirements, and includes an MSDS. Solutions come in one pint bottles. Dimensions: 7.75"H x 2.25" dia. Shpg wt: 1.1 lbs.

OAKTON Conductivity Singles pouches are convenient, air-tight pouches with high-precision calibration standards. Ideal for field use-take them to your test site for on-the-spot calibration. Pouches are labeled with equivalent values for ppm in KCl, NaCl and 442 and Conductivity values at 25°C and CAS numbers for Right-to-Know requirements. Each box contains twenty 20 mL pouches. Dimensions: 4.5"L x 5"W x 4.5"H (box). Shpg wt 1 lb per box.

• NIST traceable materials
• ±1% accuracy at 25°C

WD-05942-44 pH 7.00 Calibration Buffer Solution 4 Liter Bottle by Oakton

Choose from economical solution bottles or individually sealed pH buffer pouches.

All Oakton pH buffer solutions are freshness dated, and standardized against NIST-traceable references to ensure quality. ±0.01 pH at 25°C.

OAKTON pH buffer solution bottles are labeled with the name and CAS number for all ingredients (for Right-to-Know requirements), and are supplied with an MSDS (Material Safety Data Sheet).

OAKTON pouches are convenient, air-tight pouches with high-precision calibration standards. Ideal for field use-take them to your test site for on-the-spot calibration. Each box contains twenty 20 mL pouches. Dimensions: 4.5"L x 5"W x 4.5"H (box). Shpg wt 1 lb per box.

• NIST traceable materials
• Labeled with pH vs temperature tables for accurate calibration

WD-35820-22 Industrial Conductivity Cell, 10 ft Cable, 3/4 MNPT Threaded Housing, Epoxy Body, Graphite Sensor, K= 10 (Use with CON 100, CON 200, CON 1000, and RES 1000 controllers) by Oakton

Feature built-in temperature compensation

• Designed for continuous in-line monitoring
• Feature stripped ends for easy wiring

Choose from three different cell constants:

• K = 1.0 for midrange conductivity measurements.
• K = 10.0 for high conductivity measurements (near or above 20 mS)
• K = 0.1 for low conductivity measurements (near or below 20 µS)
• K = 0.01 for resistivity measurements (at or below 2 µS)

Install these rugged cells in a pipeline, or submerse in a tank.

Dimensions: 142 mm L x 12 mm dia. Shpg wt 0.5 lb.

WD-35811-74 Double-junction, Glass-body, Refillable pH Electrode (Use with pH 5, pH 6, pH 510, Ion 510, pH 1100, pH 2100 meters) by Oakton

Built-in temperature sensor lets you take ATC readings with a single probe

Each All-in-One Acorn electrode features a built-in temperature sensor for taking readings with Automatic Temperature Compensation (ATC). Choose a single junction electrode for field, clean water, and general purpose applications. Choose a double junction electrode for most applications, including dirty water, heavy metals and organics applications.

Each electrode is 12 mm dia with a 3 ft cable.

• Includes a FREE electrode saver bottle to extend electrode life
• Feature a BNC connector for pH and a phono jack connector for temperature

WD-00606-10 12,880 µS Conductivity/TDS Calibration Solution 500 mL (1-pint) Bottle by Oakton

Choose from economical solution bottles or individually sealed pH buffer pouches.

All Oakton pH buffer solutions are freshness dated, and standardized against NIST-traceable references to ensure quality. ±0.01 pH at 25°C.

OAKTON pH buffer solution bottles are labeled with the name and CAS number for all ingredients (for Right-to-Know requirements), and are supplied with an MSDS (Material Safety Data Sheet).

OAKTON pouches are convenient, air-tight pouches with high-precision calibration standards. Ideal for field use-take them to your test site for on-the-spot calibration. Each box contains twenty 20 mL pouches. Dimensions: 4.5"L x 5"W x 4.5"H (box). Shpg wt 1 lb per box.

• NIST traceable materials
• Labeled with pH vs temperature tables for accurate calibration

WD-35608-55 Conductivity/TDS Cell, Epoxy Body, Platinum Sensor, 3 ft Cable, K= 0.1 by Oakton

Feature built-in temperature compensation

• Ultem Cells with K = 1.0 have removable a probe guard for easy cleaning

Choose from three different cell constants:

• K = 1.0 for midrange conductivity measurements.
• K = 10.0 for high conductivity measurements (near or above 20 mS)
• K = 0.1 for low conductivity measurements (near or below 20 µS)

Each conductivity/TDS cell has a temperature range of 0 to 100°C.

WD-35653-11 1413 µS Conductivity/TDS "Singles" Calibration Solution Pouches, 20 pouches each with 20 mL of solution by Oakton

Choose from economical 1-pint solution bottles or individually sealed Singles calibration pouches.

All OAKTON Conductivity/TDS calibration solutions are cross checked using different test methods, premixed, and ready to use.

OAKTON conductivity/TDS solution bottles are labeled with the name and CAS number for all ingredients to conform with Right-to-Know requirements, and includes an MSDS. Solutions come in one pint bottles. Dimensions: 7.75"H x 2.25" dia. Shpg wt: 1.1 lbs.

OAKTON Conductivity Singles pouches are convenient, air-tight pouches with high-precision calibration standards. Ideal for field use-take them to your test site for on-the-spot calibration. Pouches are labeled with equivalent values for ppm in KCl, NaCl and 442 and Conductivity values at 25°C and CAS numbers for Right-to-Know requirements. Each box contains twenty 20 mL pouches. Dimensions: 4.5"L x 5"W x 4.5"H (box). Shpg wt 1 lb per box.

• NIST traceable materials
• ±1% accuracy at 25°C

WD-35613-80 Ion 6+ Meter Only, 0.0 to 100.0°C Temperature Range, 0.00 to 14.00 pH Range, ±1999 mV Range, and 0.01 to 1999 ppm by Oakton

Direct readout of ion concentration at economical prices

These rugged, economical meters are very easy to use. Features include all push-button calibration, hold function,auto-off, and splash-resistantkeypad. Read concentration in ppm and mV as well as pH and temperature in ºC. The included protective rubber boot also acts as a meter stand for benchtop use. Order ISE electrodes separately.

• Works with almost all ion selective electrodes with BNC connectors
• Reads ion concentration (ppm) pH, mV, and temperature
• Preprogrammed ion calibration points let even beginners take readings in minutes
• Hold function; Auto-off

WD-35604-21 TDS 6+ Handheld Total Dissolved Solids Meter with Probe, -10 to 110°C Temperature Range and 0 to 10.00, 10 to 100.0, 100 to 1000 ppm; 1.00 to 10.00, 10.0 to 100.0, up to 200.0 ppt TDS Range, with NIST Traceable Certificate of Calibration by Oakton

Customize TDS conversion factor for better accuracy

These meters feature easy, push-button operation, a convenient HOLD function, and Auto-off function that shuts meter off after 20 minutes of nonuse.

Meters offer two modes of five-point calibration. For quick and easy calibrations, use automatic mode with preset calibration points at the most popular values. For more flexibility, calibrate in the manual mode and set your calibration point at any value.

Set-up functions let you customize automatic temperature compensation, cell constant, and TDS conversion factor for better accuracy and faster use. The protective rubber boot helps shield your meter from drops and dings, and features a built-in stand.

• Includes conductivity/TDS temperature probe (K= 1.0), protective rubber boot, calibration solutions, sample bottles, hard carrying case and batteries
• High accuracy in changing temperature conditions
• Temperature readout and automatic temperature compensation (ATC)
• Calibrate the TDS 6+ at one point and all five ranges are covered

WD-00653-06 pH/ORP Electrode Cleaning Solution 500 mL (1-pint) Bottle by Oakton

Solutions to clean, store and fill electrodes

Electrode storage solution keeps pH/ORP electrode bulbs moist for faster, more accurate readings. Use storage solution with electrode saver bottle WD-35805-50 (included with all Oakton 12 mm electrodes) to extend the life of your electrode and maintain accurate readings. Accepts pH electrodes up to 12 mm in dia.

General-purpose pH/ORP electrode cleaning solution removes build-up from electrodes and maintains electrode sensitivity.

Storage and cleaning solutions come in 1 pint bottles.

Use the reference fill solutions with refillable pH electrodes.

• Extend the life of your electrodes and maintain accurate readings
• Use cleaning and storage solution with any pH or ORP electrodes

WD-35820-26 Industrial Conductivity Cell, 10 ft Cable, 3/4 MNPT Threaded Housing, Glass Body, Platinized Platinum Sensor, K = 0.1 (Use with CON 100, CON 200, CON 1000, and RES 1000 controllers) by Oakton

Feature built-in temperature compensation

• Designed for continuous in-line monitoring
• Feature stripped ends for easy wiring

Choose from three different cell constants:

• K = 1.0 for midrange conductivity measurements.
• K = 10.0 for high conductivity measurements (near or above 20 mS)
• K = 0.1 for low conductivity measurements (near or below 20 µS)
• K = 0.01 for resistivity measurements (at or below 2 µS)

Install these rugged cells in a pipeline, or submerse in a tank.

Dimensions: 142 mm L x 12 mm dia. Shpg wt 0.5 lb.

WD-35413-20 pH/Con 700 Benchtop Meter with and Electrode Stand, 110/220 VAC, 50/60 Hz by Oakton

Easily toggle between pH, mV, conductivity, TDS, and temperature measurements at the touch of a button

The pH/CON 700 meter offers a new compact design that is over 40% smaller than other benchtop meters. The large display is easy to read even at a distance. Dual-display allows you to read both a measured parameter and temperature at a glance. The meter features pH auto-buffer recognition for both USA and NIST buffer sets (1.68, 4.01, 7.00, 10.01 and 12.45 or 1.68, 4.01. 6.18. 9.86, and 12.45), automatic or manual temperature compensation, temperature selectable in either °F or °C, display HOLD, and water-resistant membrane keypad.

Previous calibration points, electrode slope and offset, and conductivity/TDS cell constants are stored in memory for quick and easy retrieval. The convenient pull-out quick reference card keeps keypad functions at your fingertips.

• Space-saving design takes up less room on the bench than other meters
• Large display lets you see your measurements from across the lab
• Conductivity and TDS autoranging chooses the best resolution for each measurement

WD-35604-20 TDS 6+ Handheld Total Dissolved Solids Meter with Probe, -10 to 110°C Temperature Range and 0 to 10.00, 10 to 100.0, 100 to 1000 ppm; 1.00 to 10.00, 10.0 to 100.0, up to 200.0 ppt TDS Range by Oakton

Customize TDS conversion factor for better accuracy

These meters feature easy, push-button operation, a convenient HOLD function, and Auto-off function that shuts meter off after 20 minutes of nonuse.

Meters offer two modes of five-point calibration. For quick and easy calibrations, use automatic mode with preset calibration points at the most popular values. For more flexibility, calibrate in the manual mode and set your calibration point at any value.

Set-up functions let you customize automatic temperature compensation, cell constant, and TDS conversion factor for better accuracy and faster use. The protective rubber boot helps shield your meter from drops and dings, and features a built-in stand.

• Includes conductivity/TDS temperature probe (K= 1.0), protective rubber boot, calibration solutions, sample bottles, hard carrying case and batteries
• High accuracy in changing temperature conditions
• Temperature readout and automatic temperature compensation (ATC)
• Calibrate the TDS 6+ at one point and all five ranges are covered