Jenco

3671N 1/8 DIN Panel Mount pH/ORP Controller by Jenco

1/8 DIN panel mount pH/ORP controller with dual SPDT Hi/Lo relays, manual set points and calibration are via potentiometers. Features a voltage/recorder output and an internal pH/ORP select switch. Display is a large bright red LED. Connectors are a BNC input and spade lug screw type connector block. Meter requires a Pt-100 ATC or a simulation resistor for temperature. Power115/230A AC.

• All solid state design
• Low cost
• Easy to install
• Set points on front panel
• Recorder output
• 0.56 high efficiency red led display
• 1/8 DIN aluminum case
• Set points cover entire span
• ATC for pH 0 to 100 °C
• Internal pH/ORP select switch
• Low power consumption design, reduced internal heating thus increased reliability

9251NKC D.O. & Temperature Handheld Polarographic Meter Kit by Jenco

Includes:

• 9251N D.O. & Temperature Handheld Polarographic Meter
• LD-900-8-DO Stainless Steel Field Probe with 8-Pin Connector 8-Pin Connector & 10-ft Cable
• LD-900-03A Membrane Kit with 6 Caps & KCL Solution
• 6230D115 AC Adapter
• Carrying Case

• Clear LCD displays dissolved oxygen as percent air saturation or as parts per thousand simultaneously with temperature.
• Convenient one point calibration for dissolved oxygen. Calibration data is stored in memory and is ready for use on power up.
• User selectable salinity and pressure compensated dissolved oxygen readings.
• Work with accurate and reliable polarographic dissolved oxygen probes.
• Inclined back provides ideal viewing angle for benchtop use.
• 50 memory storage of dissolved oxygen with temperature reading with memory location ID.
• RS-232 computer interface with software.
• IP65 waterproof.
• AC adaptor or battery power (low battery indicator).

3175K0.1 Microcomputer Based Conductivity/TDS/Temperature Benchtop Meter Kit by Jenco

Jenco EC3175 is a new conductivity meter with temperature readout, backlit LCD display, selectable cell constant and a streamlined look.

This benchtop meter is RoHS compliant.

Includes:

• 3175: Benchtop Conductivity meter
• 109: Conductivity Probe, K=0.1
• Choice of 6230D115: 120V AC adapter or 6230D230: 220V AC adapter

• Clear, large LCD display with backlight
• Displays conductivity and temperature at same time
• Accepts 2-wire conductivity cells with adjustable k=0.1, k=1 and k=10 cell constants for improved flexibility and accuracy
• Convenient one point calibration
• Calibration data is stored in memory and is ready for use on power up
• Automatically selects one of three conductivity ranges to display readings
• Readings are automatically compensated for temperature (ATC)
• Meter automatically switches into manual compensation when temperature probe is not present
• Automatic lock mode is available to lock in stable readings
• Intuitive operation with membrane keypad with tactile and audio feedback.
• Splash resistant case is made with durable, reinforced plastic for added protection. protective covers for connectors are included
• Smaller case does not clutter valuable desk space
• 8pin DIN connector for conductivity cell & 10k thermistor
• AC adaptor or battery power

3675 1/4 DIN Panel Mount pH/ORP Controller/Transmitter by Jenco

1/4 DIN panel mount pH/ORP controller/transmitter with dual SPDT Hi/Lo relays, manual set points and calibration are via potentiometers. Features a 4-20 mA current output and has an external pH/ORP select switch. Display is a large LCD. Connectors are a BNC and spade lug screw type connector blocks. Meter requires a Pt-100 ATC or a simulation resistor for temperature. Power 115/230V AC.

• Isolated 4 to 20 mA output
• Dual on/off relays
• Large LCD display
• ATC
• 115VAC /230VAC operations
• Compact 1/4 DIN case
• Low power solid state design
• Front panel output current span adjustable control
• Front panel acid/base influent select switch
• Front panel high/low relay format select switch

601AKA pH Meter Kit by Jenco

pH/mV handheld meter with manual temperature compensation and pH calibration via knobs and pH slope calibration potentiometer. Has LCD digital display, BNC connector, voltage recorder output and reference electrode pin. AC/DC Powered.

Includes:

• 601A pH/mV Handheld Meter
• 600P pH electrode
• 601AF carrying case

• Liquid crystal display readable under bright ambient conditions
• Three position rocker switch for pH off mv operations
• Recorder output
• All solid state design
• High stability
• Low drift
• Fast response
• Rugged carrying case
• UL approved ac line adaptor
• One conventional 9v battery
• Extra long battery life
• Battery low indicator

3010KA Conductivity Meter Kit by Jenco

Includes:

• 3010 Conductivity Meter
• 107A: Conductivity Probe, Glass, K=10, 3-ft

9250MKC D.O. & Temperature Handheld Polarographic Meter with Memory & RS-232 Kit by Jenco

Includes:

• 9250M: DO meter
• LD-900-10/10: DO Field Probe, Stainless Steel, 10K, 10-ft Cable, 8-Pin
• LD-900-03A: Membrane Kit with 6-Membrane Caps & KCL Solution
• 9250F: Carrying case
• Choice of 6230D115: 120V AC adapter Or 6230D230: 220V AC adapter

• Clear LCD displays dissolved oxygen as percent air saturation or as parts per thousand simultaneously with temperature.
• Convenient one point calibration for dissolved oxygen. Calibration data is stored in memory and is ready for use on power up.
• User selectable salinity and pressure compensated dissolved oxygen readings.
• Work with accurate and reliable polarographic dissolved oxygen probes.
• Inclined back provides ideal viewing angle for benchtop use.
• 50 memory storage of dissolved oxygen with temperature reading with memory location ID.
• RS-232 computer interface with software.
• IP65 waterproof.
• AC adaptor or battery power (low battery indicator).

6360KB Handheld/Portable pH/ORP/Conductivity/Temperature Meter Kit by Jenco

Includes:

• 6350N: Conductivity mete
• 600P: pH/Ref. electrode
• Choice of 6230D115: 120V AC adapter Or 6230D230: 220V AC adapter
• 6230F: Carrying Case with pH4, pH7 buffer capsule

5005KC pH Meter Kit by Jenco

pH/mV/Temp. handheld meter with build in tabletop stand with LCD digital display. Meter has both ATC and manual temperature compensation. pH standardization calibration is via knobs and pH slope calibration is via potentiometer. Features include a voltage recorder output, reference input pin and BNC input connector. AC/DC Powered.

Includes:

• 5005 pH/mV/Temp. handheld meter
• 600A Temp. probe
• 600P pH electrode
• 600D115 AC adapter
• 5005F carrying case with pH 4 & 7 capsules

• All solid state design
• Fast input response
• Low drift and high stability
• Tilt stand
• Greater than 100db 50/60hz rejection
• Battery low indicator
• Extra long battery life
• Auto polarity mv measurement
• Analog recorder output
• Rugged carrying case
• UL approved ac line adaptor
• Aconventional 9v battery
• Manual and ATC for pH measurement
• 0 to 100.0 °C range of temperature measurement
• 0.5 high liquid crystal display readable under bright ambient conditions

3010M+109A Handheld Cond/TDS/Sal/Temp Meter Kit by Jenco

Includes:

• 3010M Handheld Cond/TDS/Sal/Temp Meter
• 109A Two-wire conductivity cell with 4 PIN connector, K=0.1 (0.0~200.0uS/cm).

• Simultaneous displays of conductivity, salinity or TDS with temperature measurements.
• 50 data set reviewable memory.
• Convenient one point calibration. Calibration data is stored in memory and ready for use on power up.
• Selectable cell constants for true wide range readings.
• Adjustable TDS coefficient, reference temperature and temperature coefficient.
• Uses one conductivity cell for conductivity, salinity and TDS measurements.
• Accepts 2-wire conductivity cells with K=0.1, 1.0 and 10.0 cell constants for improved flexibility and accuracy.
• Automatic shutoff function (30 minutes of non-use).
• Battery life over 1000 hours.
• IP65 waterproof.
• Low battery indicator.
• RoHS and CE compliant.

9173RK Large LCD Polarographic Benchtop Meter with RS-232 Kit by Jenco

Dissolved Oxygen benchtop meter with extra large LCD display for ease of use. The meter uses polarographic type sensor with replaceable membranes and programmable pressure compensation, 600 to 1000 mBar and salinity compensation, 0 to 40.0 ppt. Communications is via. Features dual LCD displays for D.O. and temperature and an RS-232-C interface. ATC is a 10k thermistor. Power is 115/230V AC or by battery.

Includes:

• 9173R Large LCD Polarographic Benchtop Meter with RS-232
• LD-900-7-DO Laboratory D.O. Probe with 8-Pin Connector
• LD-900-03A Membrane Kit with 6 Caps & KCL Solution
• 6230D115 AC Adapter

• Clear, large LCD display (4 1/8 x 3 1/16 in.).
• Clear LCD displays D.O. as percent air saturation or D.O. as parts per thousand, simultaneously with temperature.
• Manual or automatic temperature compensated (ATC) D.O. readings.
• User selectable salinity and pressure compensated D.O. readings.
• Works with accurate and reliable polarographic D.O. probes.
• Convenient one point calibration for D.O. calibration data is stored in memory and is ready for use on power up.
• Automatic lock mode and end point sensing are available to lock in stable readings.
• Intuitive operation with membrane keypad with tactile and audio feedback.
• Splash resistant case is made with durable, reinforced plastic for added protection. protective covers for connectors are included.
• Large LCD is offset for improved protection against unintentional damage.
• Smaller case does not clutter valuable desk space.
• RS-232 computer interface.
• 8pin DIN connector for D.O. and thermistor.
• AC adaptor or battery power.

pH618NF pH/Temperature with Memory and Replaceable pH Electrode by Jenco

VisionPlus pH618N is the successor of the popular pH618 advanced pH tester with IP67 body, temperature readout, 50 data point storage, menu driven operation and replaceable electrode module. VisionPlus pH618N takes useful features typically found in larger, portable meters and packed them into a small, easy to use package. Available in two different models: one for °Celsius temperature readout and one for Fahrenheit temperature readout.

VisionPlus pH618N is RoHS compliant.

• Graphical LCD provides on-screen menu selection for manual-free, easy operation.
• On-screen messaging displays useful information such as meter status, buffer selection and operation modes. no more guess work involving cryptic indictors or flashing digits.
• 50 memory storage of both pH and temperature readings with memory location id and date and time stamp.
• 4-button keypad provides intuitive operation with separate buttons for data hold, calibration, data memory storage and memory retrieval.
• IP67 rated, water-proof dust-proof body.
• Glass bulb electrode exposes more measuring surface to solution for fast response time.
• Surface mounted temperature element improves temperature accuracy and response time.
• Indicates exact date and time of last calibration so users can decide optimal maintenance schedule.
• Real-time date and time display.
• Clear LCD displays pH and temperature at the same time, along with meter status, calibrated buffers, status, date and time.
• Large temperature range for wide range of applications.
• 1,2, or 3 point calibration, with automatic buffer recognition of us and nist buffer sets.
• Calibration data is stored in memory, ready for use on power up, even when batteries are removed.
• Readings are automatically compensated for temperature (ATC).
• Data hold for convenient reading.
• Watertight case is ideal for rugged use. protective cover for pH electrode is included.
• Replaceable electrode module ensures extended usefulness.
• Belt clip which also attaches to neck strap.
• 1 year warranty.

EC331 VisionPlus Resistivity/Conductivity Meter by Jenco

Jenco EC331 is an easy to use, IP67 rated conductivity tester with resistivity and temperature readout. Key features include dual display of conductivity or resistivity with temperature, selectable or auto ranging, replaceable conductivity cell and IP67 rated body.

This tester is RoHS compliant.

• Simultaneous display of conductivity and temperature, or resistivity and temperature
• Convenient 1 point calibration
• Automatic temperature compensation
• Selectable or auto ranging of conductivity and resistivity readings
• Replaceable stainless steel conductivity cell ensures extended usefulness
• 4 selectable units of measure (uS/cm, M?, °C, °F)
• Battery life of over 100 hours
• Data hold