Test and Measurement, Jenco

3621 Industrial pH/ORP Controller, LCD Display, 1/8 Din Panel Mount by Jenco

• Easy to install 1/8 DIN plastic casing.
• Clear LCD displays pH, mV or temperature with backlight.
• Universal power supply input from 100-240VAC.
• Automatic buffer recognition of US and NIST buffer sets. Calibrated data is stored in memory and ready to for use on power up.
• Automatic or manual temperature compensation.
• Displays absolute and relative ORP.
• Two sets of programmable on/off relays for pH or ORP (3621).
• Isolated and reversible 4-20mA current output for pH or ORP allows it to be used as a proportional output (3631).
• RoHs compliant.

692 1/8 DIN Panel Mount pH Transmitter with 4-20 mA Output by Jenco

1/8 DIN panel mount pH transmitter with 4-20 mA output and calibration by potentiometers. ATC temperature control uses a Pt-100 or simulation resistor. Features a large LCD display and uses a BNC input and spade lug screw type connector block.

• All solid state design
• ATC
• Low power consumption design, reduced internal heating thus increased reliability
• 0.56 high LCD display
• Isolated 4 to 20 mA current output
• High stability and fast response
• 1/8 DIN standard aluminum case
• Easy to install
• Heat cycled 100 hours before shipment

701TF Temperature Magnetic Back Meter, Type T by Jenco

Model 701 is a battery operated thermocouple type digital thermometer that measures approximately 3x2.25x1.13 inches (77x60x30mm). It is available in 6 different configurations of thermocouple calibration with Celsius or Fahrenheit reading.

• All solid state design
• High stability
• Wide temperature range
• cold junction compensation
• Easy to read LCD display
• One conventional 9V battery
• Long battery life
• Interchangeable TC sensor

3675 1/4 DIN Panel Mount pH/ORP Controller/Transmitter by Jenco

1/4 DIN panel mount pH/ORP controller/transmitter with dual SPDT Hi/Lo relays, manual set points and calibration are via potentiometers. Features a 4-20 mA current output and has an external pH/ORP select switch. Display is a large LCD. Connectors are a BNC and spade lug screw type connector blocks. Meter requires a Pt-100 ATC or a simulation resistor for temperature. Power 115/230V AC.

• Isolated 4 to 20 mA output
• Dual on/off relays
• Large LCD display
• ATC
• 115VAC /230VAC operations
• Compact 1/4 DIN case
• Low power solid state design
• Front panel output current span adjustable control
• Front panel acid/base influent select switch
• Front panel high/low relay format select switch

77A-RTD, Type RTD, 2-Wire Temperature Transmitter and 3-Wire RTD Connection, Temperature Range 0 - 250°F (77A-11/0000/+0250/FAH) or 0 - 500°F (77A-11/0000/+0500/FAH) by Jenco

2-wire thermo well head type 4-20 mA current loop output signal temperature transmitter for thermocouple or RTD applications, 3 user selectable temperature ranges and adjustable Zero Span with current output proportional to the display LED s brightness. Two ambient temperature ranges are available model 77 and 77A. Specify type J, K, E, T or RTD and specify temperature range.

• Fits standard thermo well heads
• 12-36 vdc powered
• 3user-select measurement ranges
• Current proportional led brightness
• Factory calibrated
• User adjustable zero/span
• 2ambient temperature ranges
• Factory custom calibration available

6308PT 1/4 DIN Panel Mount pH Single Parameter Analyzer by Jenco

1/4 DIN panel mount pH single parameter analyzer with electrode efficiency display function. Features pH linear or antilog transmitter output, hysteresis control and uninterrupted operation during pH calibration. Has one 4-20mA output, 5 relays and a RS-485 communications interface. Graphical display. 115/230V AC. CE Approved.

• Bright, graphical LCD display, 1.5 x 2.25
• Simultaneous measurement and analysis
• 1/4 DIN watertight, ip65 rated enclosure
• Reversible & isolated 4 to 20ma output with adjustable bandwidth
• Continuous controller / relays operation during calibration
• 4-digit password security protection
• Programmable set point hysteresis
• Automatic temperature compensation
• CE approved
• Built in ISO9001 certified facility
• Membrane keypad with audio feedback
• Power down, non-volatile memory backup
• RS-485 output
• Multiple spst on/off relays
• Embedded self diagnostic program
• High 50/60 hz noise rejection

3173 Large LCD Conductivity/TDS/Temperature Benchtop Meter by Jenco

Conductivity/TDS/Temperature benchtop meter, with an extra large LCD display, adjustable cell constants K=0.1, 1.0, 10.0, programmable temperature co-efficient and reference temperature. Battery or 115/230 AC powered. CE approved.

• Clear, large LCD display (4 1/8 x 3 1/16 in.).
• Displays conductivity and temperature, or tds and temperature readings at the same time.
• Accepts 2-wire conductivity cells with adjustable k=0.1, k=1 and k=10 cell constants for improved flexibility and accuracy.
• Auto or manual ranging of 3 conductivity ranges are available for improved usability.
• Convenient one point calibration. calibration data is stored in memory and is ready for use on power up.
• Readings are automatically compensated for temperature (ATC). meter automatically switches into manual
• compensation when temperature probe is not present.
• Automatic lock mode is available to lock in stable readings.
• Intuitive operation with membrane keypad with tactile and audio feedback.
• Splash resistant case is made with durable, reinforced plastic for added protection. protective covers for connectors are included.
• Large LCD is offset for improved protection against unintentional damage.
• Smaller case does not clutter valuable desk space.
• 8pin DIN connector for conductivity cell & 10k thermistor.
• AC adaptor or battery power.

3631 Industrial pH/ORP Controller, LCD Display, 1/8 Din Panel Mount by Jenco

• Easy to install 1/8 DIN plastic casing.
• Clear LCD displays pH, mV or temperature with backlight.
• Universal power supply input from 100-240VAC.
• Automatic buffer recognition of US and NIST buffer sets. Calibrated data is stored in memory and ready to for use on power up.
• Automatic or manual temperature compensation.
• Displays absolute and relative ORP.
• Two sets of programmable on/off relays for pH or ORP (3621).
• Isolated and reversible 4-20mA current output for pH or ORP allows it to be used as a proportional output (3631).
• RoHs compliant.

6313 Single Parameter pH or ORP Controller, 2-Relays, IP-65 Case, RS-485 by Jenco

• Clear LCD displays pH or mV, with temperature and relay status simultaneously.
• Automatic buffer recognition of US and NIST buffer sets. Calibration data is stored in memory and is ready for use on power up.
• Displays absolute and relative ORP.
• Isolated and reversible 4-20 mA current output for pH or ORP allows it to be used as a proportional output.
• 2 programmable on/off relays: 2 for pH or ORP.
• CE Approved
• Password protection.
• IP65

765JF Thermocouple Panel Thermometer, Type J, Range -346°F to 1400°F by Jenco

Panel mount digital thermometer with analog voltage output of 1 mV per digit, with analog output accuracy of ± 0.2%, features a bright red LED display and 1/8 DIN plastic housing. °C/°F selectable via plastic jumper behind front bezel. Available in types. J, K, T, E, and 3-wire Pt-100 RTD. Ambient range 0 to 60°C. 115/230V AC operation.

• High accuracy
• 50/60 hz rejection design
• Compact 1/8 DIN plastic case
• °C/°F selectable w/ re-calibration
• Models available for k,j,t,e pt-100
• Upscale break detection
• Cold junction consumption design
• 1mv/digit analog output
• Easy to install
• 0.56 high efficiency ide display