All Products

P250BR Non-Switchable Passive Oscilloscope Probe, 250MHz, x 10 with Readout, 1.2M Cable Length by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

XT-X0HM-Y-AU GasAlertMax XT II 3 Gas Detector, Oxygen (O2), Hydrogen Sulfide (H2S), Carbon Monoxide (CO) - Yellow Housing, AU Version (Australia) by BW Technologies

GasAlertMax XT II is the safest and most economical choice for multi-gas detection systems. Utilizing the most advanced technology on the market, the GasAlertMax accurately and reliably monitors up to four hazardous conditions, and offers a simple user friendly device for easy operation. Its standard safety features and compatibility with other instruments ensure that the gas detector is the best instrument for gas monitoring compliance.

GasAlertMax XT II specifications

The lightweight and portable unit is approximately 11.5 ounces, and features the latest technology allowing for a compact design. With an operational temperature range of -4 to 122 degrees Fahrenheit, the monitor is designed to function effectively in many harsh conditions. The cautionary yellow outer shell helps to ensure that the gas detector is carried with the user not left onsite. Additionally, the durable casing is resistant to water and features a built-in concussion proof boot.

Triple alarm system

The GasAlertMax XT II features a triple alarm system designed to alert users of potentially hazardous conditions. When the gas sensors detect specified levels of H2S, CO, O2, or combustible gases, the instrument will begin the triple alarm alert and notify users and those nearby. The device indicates these dangers with a vibrating alarm, an ultra bright visual alarm, and an audible alarm of over 95 decibels. The alarms are also designed to alert users of administrative needs such as battery replacement.

GasAlertMax XT II features

The GasAlertMax XT II has multi-language support features in English, French, Spanish, German, and Portuguese. The gas detector also has state of the art block detection with semi-conductor pressure sensor, and standard data and event logging. Accessories such as the belt holster, multi-unit cradle charger, and concussion proof boot are also available.

Upon activation, the unit will automatically test sensors, pumps, battery, and circuitry. For additional test and calibration, the GasAlertMax XT II is compatible with the MicroDock II automated test and calibration system and Fleet Manager II. Improving on its functionality, the unit is customizable. Users can change options for forced calibration and tests, safety locks, alarm setpoints, safe display mode, language choices, start-up message, and more.

The easy to read LCD screen displays continuous information about real-time gas concentrations and alarms. To maintain simplicity and ease of use, the GasAlertMax XT II also features a user and glove friendly one touch button for operation. The no-frills design has an added benefit of minimizing cost and user training. This simple, portable, and compact detector is the best instrument for confined spaces or potentially dangerous worksites.

Highest standards of reliability

The typical batter life ranges between 8 and 13 hours depending on the temperature. The durable and long lasting batteries can fully recharge in approximately 6 hours. The GasAlertMax XT II and its sensors feature a standard two year warranty. With safety and reliability as a top priority, BW Technologies has developed the multigas detector to utilize the most advanced technology on the market, while maintaining its simplicity and portability. When working in settings with possible gas exposure, users can be certain that the gas levels are being accurately and reliably monitored with the best technology available.

Part Number: XTX0HMYAU

723-117-20 Eagle 2 Portable Monitor for Hydrogen H2 100% Volume (TC)/O2/H2S by RKI Instruments

Continuing in its legacy of durable and reliable gas detection and monitoring systems, RKI Instruments is proud to offer a new product in its popular Eagle portable gas detector series. The Eagle 2 can monitor up to 6 different gases and is equipped with several exclusive features that can only be found with the Eagle series. In addition, its large glove friendly push buttons and LCD screen ensure an ease of use when onsite. Rated intrinsically safe, the Eagle 2 is equipped with state of the art technologies that are not available with other competitive gas detectors and monitors.

Specialty Sensors

The Eagle 2 has a variety of available specialty sensors. Workers can use a photoionization detector for low or high range VOC detection and Fence Electrode Technology for humidity and contamination resistance. An infrared sensor is available for Co2, % LEL CH4, % Volume CH4, % LEL HC, and % Volume HC. Thermal conductivity sensors are available for % Volume H2 and % Volume CH4. The unit is also compatible with the smart plug and play toxic sensors for the detection of NH3, AsH3, CI2, HCN, PH3, and SO2. With the wide variety of sensors and gas detection available, the Eagle 2 can be customized to meet almost all worksite gas detection needs.

Exclusive Features

The monitor has a long internal pump that can draw samples for up to 125 feet. The pump features a low flow auto shut off and alarm. This allows operators to respond swiftly from a safe distance. The unit is multilingual with 5 different language preferences, and features an alkaline battery life of 18 hours or a NiMH life of 20 hours. To protect the integrity of the device and the configurations, the unit can be password protected. The Eagle 2 also has standard data logging capabilities for easy research, evaluation, and site monitoring. To reduce calibration costs and time, the unit features an automatic calibration option and a single gas calibration option.

The Eagle 2 is heavily protected from environmental conditions by a weather proof, chemical resistant RFI/EMI coated high impact polycarbonate/PBT blend enclosure. The enclosure also renders the unit water and dust resistant. Because of the enclosure, the Eagle 2 can function in 2 inches of water without leakage.

Eagle 2 Specifications

The portable and durable unit is lightweight at less than 4 pounds. Its dimensions are suitable for convenient carrying (9.5?L x 5.25?W x 5.875?H), and it features a conveniently placed durable top handle. The large easy to read display has a polyurethane overlay backlights on demand and when the alarm is activated. The 2 alarm channels are fully adjustable for the user and can be password protected. With a 95 dB buzzer and 4 high intensity LEDs, the alarm is sure not to be missed. The Eagle 2 is standard with a 2 year warranty for material and workmanship and a 1 year warranty for PID sensor.

*Please note we can only ship RKI products to customers within the United States

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

72-0310RKA GX-2009 Personal Gas Monitor, 3 Gas LEL / O2 / H2S with Alligator Clip, 12 VDC Charger & Vehicle Plug by RKI Instruments

Workplace safety is a top priority at RKI Industries. With a reputation as being a world leader in gas detection and sensor technology, the company invests heavily in their research and design team to develop the industry's leading workplace safety products. The GX-2009 Model Personal Four Gas Monitor utilizes advanced technology and efficient design. It is the world's smallest and lightest gas monitor.

The GX-2009 Model Personal Four Gas Monitor

The GX-2009 Model Personal Four Gas Monitor is an obvious choice for many particularly hazardous applications. From personal monitoring in confined spaces to its use in fire services and construction, the portable monitor has been rated intrinsically safe. Its noticeable alarm functions and simultaneous detection of four separate gases help to ensure the safety of workers in potentially dangerous situations. The state of the art monitor can detect LEL, O2, H2S, and CO simultaneously and display the results on the large LCD display screen.

Each of the miniature sensors are manufactured with the high quality control standards of RKI Instruments. The compact sensors utilize catalytic combustion, electrochemical, and galvanic sensor technology.

Alarm System

The unit features dual audible alarm ports at 95 dB, and three bright LED lights for noticeable alerts. The Personal Four Gas Monitor also utilizes an ultra strong vibration alert designed to notify users of atmospheric conditions even when the device cannot be heard. When the monitor is in alarm mode, the backlight on the LCD display is turned on. The multi-faceted alarm system is designed to be noticeable in any given situation and is sure to notify the user and those nearby.

Standard Features

The GX-2009 Model Personal Four Gas Monitor has many standard features including an incredible datalogging function. The datalogging software can store up to 100 calibration records and is compatible with many computer platforms. The log time can range from 10 to 300 hours and houses 8 alarm trends. The unit can also remind users of upcoming calibration and bump tests. With 2 glow in the dark, glove friendly buttons, users can easily operate the device on site.

The unit comes standard with an alligator clip, NiMH batteries, a charging station with VAC power supply, and a product CD with datalogging software.

Specifications

The GX-2009 Model Personal Four Gas Monitor is the smallest and lightest personal gas monitor in the world. Weighing in at less than 5 ounces, the device fits easily in the palm of a hand and is easily portable. Additionally, the IP-67 water resistant and dustproof design contains an impact resistant over mold rubber body to protect the integrity of the device. The unit uses a set of 2 NiMH batteries with 20 hours of operation. Each GX-2009 Model Personal Four Gas Monitor comes standard with a 2 year warranty for materials and workmanship.

*Please note we can only ship RKI products to customers within the United States

2813-4505-002 EC 28i Intrinsically Safe Transmitter with Sensor, Ammonia (NH3), 0-500 ppm, Display by GfG

Features

• Full-featured smart transmitter for oxygen or a wide range of toxic gas measurement
• Non-intrusive AutoCal calibration adjustment
• Increased safety design to reduce installation cost in potentially hazardous locations
• Intrinsically safe (i) EX-Proof version
• BVS 04 ATEX E 132 X (electrical ex-protection) II 1G EEx ia IIC T4 C 0158
• Available in two configurations: Blind (no display), Display
• Barriers are required
• EX- conduit is not required
• Reduced installation costs

WD-35607-91 CON 150 Portable Waterproof Conductivity Meter Kit with NIST Certificate by Oakton

The CON 150 meter offers a rugged, waterproof housing with built-in stand at an economical price. The large, three-line LCD lets you view the conductivity or TDS measurement simultaneously with temperature. Convenient auto-ranging and auto-cal functions for one calibration point per measurement range. Select a two-cell probe with a 0.1, 1.0, or 10 cell constant and automatic temperature compensation (ATC). ATC ensures measurement accuracy even in fluctuating temperatures. Select temperature readout from C/F to suit your application.

Meter features include ready (stability) indicator, smart averaging, hold function, calibration alarm (visible), battery life indicator, and probe status. Data storage allows manual storage and recall of 150 data sets, as well as the log of the last calibration data.

• Intuitive, user-friendly icons probe status displays cell constant
• Grip-Clip holder quickly and easily secures the probe to your beaker or container
• Expanded data logging for up to 150 data sets
• 700 hours battery life or optional universal power adapter
• Built-in stand and wall-mount option allow for easy laboratory measurement or storage

183A True RMS DMM with Temperature, Capacitance, Duty Cycle and Low-pass Filter by Test Products International

The 183A is a hand-held autoranging DMM. The 183A measures ACV, DCV, ACA, DCA, Resistance, Frequency, Duty Cycle, Diodes, Capacitance, Temperature and Continuity. The meter is also easy to use and built to last.

Features:

• REC: Records Min/Max and Average readings during specified measurement intervals.
• Range: Allows the user to manually range the 183A instead of autoranging.
• Hold: Holds the reading on the display for easy viewing.
• REL: Displays the value as a difference to a reference value.
• Auto Off: Preserves battery life.
• Rubber Boot: Added protection when the instrument is dropped.
• 0.5% DCV basic accuracy
• 0 to 750 ACV; max resolution 1mV
• 0 to 1,000 DCV; max resolution 0.1mV
• 0 to 32.6MΩ; max resolution 0.1Ω
• Audible continuity
• 0 to 10 amps AC/DC; max resolution 0.1uA
• Analog bar graph
• cULus 61010-1
• CAT II - 1000V, CAT III - 600V

Applications:

• Thermocouples in furnaces or gas applications
• Heat anticipator current in thermostats
• Line voltage
• Voltage of direct drive DC motors
• Control circuit voltage
• Motor run and start capacitors
• Flame safeguard control current
• Heating element resistance (continuity)
• Compressor winding resistance
• Contactor and relay coil resistance
• Continuity of wiring
• Continuity of circuit breakers
• Temperature with optional temperature adapter
• Bar graph to indicate rapid fluctuations in measurements

The 183A comes complete with the following accessories:

• 183A Instrument
• Zippered Vinyl Carrying Case
• Rubber Boot
• Test Lead Set
• Instruction Manual

72-5301RK Eagle Portable Monitor for LEL& PPM/O2/H2S by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

Part Number: 221L-389

72-5494RK-XX Eagle Portable Monitor for O2/H2S/NH3/CO2 (Specify CO2 Range) by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

WD-20250-08 50:1 Data Logging IR Thermometer with T/C Input and NIST Traceable Calibration by Digi-Sense

Ergonomic pistol-grip infrared (IR) thermometers provide the precision you need for quick and easy temperature measurements. Noncontact meters safely measure the surface temperature of objects without physically touching the object. Simply aim, pull the trigger, and read the display—reliable measurements couldn't be easier!

Features

• Reliable measurements, guaranteed! Precalibrated to NIST-traceable standards.
• Laser sighting helps target the measuring area
• Large backlight LCD with backlight for easy viewing
• Adjustable emissivity (except model 20250-04)
• Min/Max readings and data Hold function
• User-selectable temperature readout in °C or °F
• Automatic selection range and display resolution
• Trigger lock for continuous scanning of temperatures
• Auto power-off mode extends battery life
• Dual-laser sighting to pinpoint target areas
• Higher distance-to-sight (D/S) ratios for long-distance measurements
• Extended temperature ranges
• Temperature differential and average readings
• USB interface for data transmission to PC
• Heavy-duty construction and protective lens cover
• External type K input for contact measurements
• Internal logging of 100 readings (model 20250-08 only)

Applications

• Agricultural
• Educational
• Food processing
• HVAC
• Industrial
• Laboratory
• R&D
• Preventive maintenance

Part Number: 10L-481

726-125-P2 Eagle 2 Portable Monitor for LEL & PPM (Catalytic)/O2/H2S/CO/VOC?s (0 - 2,000 ppm, PID)/HCN by RKI Instruments

Continuing in its legacy of durable and reliable gas detection and monitoring systems, RKI Instruments is proud to offer a new product in its popular Eagle portable gas detector series. The Eagle 2 can monitor up to 6 different gases and is equipped with several exclusive features that can only be found with the Eagle series. In addition, its large glove friendly push buttons and LCD screen ensure an ease of use when onsite. Rated intrinsically safe, the Eagle 2 is equipped with state of the art technologies that are not available with other competitive gas detectors and monitors.

Specialty Sensors

The Eagle 2 has a variety of available specialty sensors. Workers can use a photoionization detector for low or high range VOC detection and Fence Electrode Technology for humidity and contamination resistance. An infrared sensor is available for Co2, % LEL CH4, % Volume CH4, % LEL HC, and % Volume HC. Thermal conductivity sensors are available for % Volume H2 and % Volume CH4. The unit is also compatible with the smart plug and play toxic sensors for the detection of NH3, AsH3, CI2, HCN, PH3, and SO2. With the wide variety of sensors and gas detection available, the Eagle 2 can be customized to meet almost all worksite gas detection needs.

Exclusive Features

The monitor has a long internal pump that can draw samples for up to 125 feet. The pump features a low flow auto shut off and alarm. This allows operators to respond swiftly from a safe distance. The unit is multilingual with 5 different language preferences, and features an alkaline battery life of 18 hours or a NiMH life of 20 hours. To protect the integrity of the device and the configurations, the unit can be password protected. The Eagle 2 also has standard data logging capabilities for easy research, evaluation, and site monitoring. To reduce calibration costs and time, the unit features an automatic calibration option and a single gas calibration option.

The Eagle 2 is heavily protected from environmental conditions by a weather proof, chemical resistant RFI/EMI coated high impact polycarbonate/PBT blend enclosure. The enclosure also renders the unit water and dust resistant. Because of the enclosure, the Eagle 2 can function in 2 inches of water without leakage.

Eagle 2 Specifications

The portable and durable unit is lightweight at less than 4 pounds. Its dimensions are suitable for convenient carrying (9.5?L x 5.25?W x 5.875?H), and it features a conveniently placed durable top handle. The large easy to read display has a polyurethane overlay backlights on demand and when the alarm is activated. The 2 alarm channels are fully adjustable for the user and can be password protected. With a 95 dB buzzer and 4 high intensity LEDs, the alarm is sure not to be missed. The Eagle 2 is standard with a 2 year warranty for material and workmanship and a 1 year warranty for PID sensor.

*Please note we can only ship RKI products to customers within the United States

6201-5112 IAM-100 Gas Detector, Remote Sensor/Faceplate, R600a 0-5000ppm, 110 VAC by Bacharach

The IAM-100 Gas Monitor from Bacharach offers exceptional continuos monitoring performance and flexibility at an economical price. By itself, or integrated into a comprehensive detection system, the IAM-100 is a scalable solution for detecting a variety of refrigerants, combustible gases and VOC gas leaks at the lowest possible cost.

Onboard LEDs illuminate when the sensor is in an alarm state while the unit's audible alarm alerts personnel in the area that levels have exceeded the desired limit. The audible alarm can be muted with the onboard silence switch. Integrated dual relays enable the IAM-100 to shut-off refrigerant or propane supply lines while the second relay can be used as a connection to a building BMS or BAS system.

The IAM-100 is an alarm threshold device. When the range of the sensor is exceeded, the detector will go into alarm. For example, a unit with a 1,000 ppm R-410a sensor will activate its alarm when the detected refrigerant meets or exceeds 1,000 ppm.

Features & Benefits:

• Real-time continuous gas detection that's scalable, reliable and affordable
• Ideal for commercial applications such as hotel rooms, apartments, dorms, hospitals, restaurant kitchens or battery charging rooms
• Detects refrigerants (at ?1,000 or ?10,000 ppm), TVOCs (at ?1,000 ppm), combustible gases and hydrocarbons (at ?5,000 ppm)
• Fast-responding, long-life sensors
• Integrated visual LED and audible alarms
• Two onboard relays to activate shut-off valves, exhaust fans, or connect to a BMS or fire panel
• Remote sensor with aesthetic faceplate available for discreet monitoring in decorative interiors

72-5425RK-01 Eagle Portable Monitor for LEL/O2/NH3/NO2, Modified for Extra RF Resistance by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

723-016-05 Eagle 2 Portable Monitor for LEL & PPM/O2/CO2 60% Volume (IR) by RKI Instruments

Continuing in its legacy of durable and reliable gas detection and monitoring systems, RKI Instruments is proud to offer a new product in its popular Eagle portable gas detector series. The Eagle 2 can monitor up to 6 different gases and is equipped with several exclusive features that can only be found with the Eagle series. In addition, its large glove friendly push buttons and LCD screen ensure an ease of use when onsite. Rated intrinsically safe, the Eagle 2 is equipped with state of the art technologies that are not available with other competitive gas detectors and monitors.

Specialty Sensors

The Eagle 2 has a variety of available specialty sensors. Workers can use a photoionization detector for low or high range VOC detection and Fence Electrode Technology for humidity and contamination resistance. An infrared sensor is available for Co2, % LEL CH4, % Volume CH4, % LEL HC, and % Volume HC. Thermal conductivity sensors are available for % Volume H2 and % Volume CH4. The unit is also compatible with the smart plug and play toxic sensors for the detection of NH3, AsH3, CI2, HCN, PH3, and SO2. With the wide variety of sensors and gas detection available, the Eagle 2 can be customized to meet almost all worksite gas detection needs.

Exclusive Features

The monitor has a long internal pump that can draw samples for up to 125 feet. The pump features a low flow auto shut off and alarm. This allows operators to respond swiftly from a safe distance. The unit is multilingual with 5 different language preferences, and features an alkaline battery life of 18 hours or a NiMH life of 20 hours. To protect the integrity of the device and the configurations, the unit can be password protected. The Eagle 2 also has standard data logging capabilities for easy research, evaluation, and site monitoring. To reduce calibration costs and time, the unit features an automatic calibration option and a single gas calibration option.

The Eagle 2 is heavily protected from environmental conditions by a weather proof, chemical resistant RFI/EMI coated high impact polycarbonate/PBT blend enclosure. The enclosure also renders the unit water and dust resistant. Because of the enclosure, the Eagle 2 can function in 2 inches of water without leakage.

Eagle 2 Specifications

The portable and durable unit is lightweight at less than 4 pounds. Its dimensions are suitable for convenient carrying (9.5?L x 5.25?W x 5.875?H), and it features a conveniently placed durable top handle. The large easy to read display has a polyurethane overlay backlights on demand and when the alarm is activated. The 2 alarm channels are fully adjustable for the user and can be password protected. With a 95 dB buzzer and 4 high intensity LEDs, the alarm is sure not to be missed. The Eagle 2 is standard with a 2 year warranty for material and workmanship and a 1 year warranty for PID sensor.

*Please note we can only ship RKI products to customers within the United States

TLSIND1 Industrial Test Lead Kit by Test Products International

Includes

• A038 Modular Sprung Hook Set
• A052 M4.0/0.7 Thread Safety Plug Adaptor
• A054 Modular Test Prod Set with Sharp Steel Point
• A057 Pair Back Probing Probes Part
• A066 1000V Fully Insulated Crocodile Clip.
• A067 Modular Grabber Clips
• A081 Modular Silicone Test Lead Set

GHS1269 Corrosion Pictogram Placard (10.75" x 10.75") by GHS Safety

These large format HazCom GHS Pictograms are 10.75" x 10.75" (273 mm x 273 mm) and perfect for marking your containment vessels or tanks. Printed on outdoor grade peel and stick vinyl with durable fade resistant inks, these pictograms are made to withstand the elements.

They come with a back split liner for easy application and are sold individually or in packages of 100.