All Products

Part Number: 34L-175-25

SP60B Switchable Passive Oscilloscope Probe, 60MHz, 1.2M Cable Length by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

65-2331RKSS S2 Series Detector/Amp/XP Stainless Steel J-Box, CSA XP, H2S, 0 - 100 ppm by RKI Instruments

Having a reliable gas sensor is detrimental to the safety and security of workers in potentially unstable work environments. In many cases, the decision to use a gas detection device with a reliable sensor can be the difference between life and death. RKI Instruments understands the reliability of gas sensors should be a top priority for workplace safety managers. Their team of experts works diligently to incorporate the most advanced technologies with the highest industry standards.

For nearly 20 years, RKI Instruments has worked in the gas detection industry. Its line of products leads the industry in innovation and technology. Every year, the company commits to achieving a higher level of productivity and delivering the best gas detection products on the market. With the introduction of their high performing, low cost S2 Sensor Transmitter, RKI is fulfilling that commitment.

S2 Sensor/Transmitter

The RKI S2 Sensors and Transmitters use state of the art sensor technology to detect common gas hazards. Their efficient design and cost effectiveness make them an industry choice for atmospheric monitoring. The sensor transmitters can be used in both indoor and outdoor conditions and are designed to interface with RKI controllers or PLC/DCS systems.

The sensors are available in explosion proof casing for monitoring LEL, H2 specific, oxygen, H2S, CO2, and carbon monoxide. These sensors also have flame arrestors and are approved for use in hazardous environments. The oxygen, H2S, CO, and CO2 sensors are available in non-explosion proof models. The sensors provide highly specific and quick detection and are long lasting. The sensors can be quickly replaced while on the field and do not require any tools.

Explosion proof S2 Sensor/Transmitter

The explosion proof sensors use a variety of detection mechanisms including catalytic for LEL and LEL- H2 specific; metal oxide semiconductor for hydrogen; galvanic cell technology for oxygen; electrochemical for hydrogen sulfide and carbon monoxide; and infrared for carbon dioxide, methane, and hydrocarbons. A hydrogen specific sensor transmitter is not available. Each of these detection methods come with their own measuring range specifications and response times varying from 20 seconds to 45 seconds. These sensors are stainless steel and are housed in a cast aluminum explosion proof J-Box (a stainless steel J-Box is also available).

Non-explosion proof S2 Sensor/Transmitter

The non-explosion proof sensors use galvanic cells for oxygen detection; electrochemical technology for hydrogen sulfide, carbon monoxide, and other toxics; and infrared technology for carbon dioxide detection. The response times vary between 20 seconds and 60 seconds depending on the targeted gas, and the measuring ranges vary as well. These sensors are plastic or aluminum and housed in an explosion proof J-Box.

Accessories

The S2 Sensor/Transmitter has numerous accessories available to meet the individual workplace's needs. Such accessories include calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors or panels, and data loggers.

Each sensor comes standard with a one year warranty for materials and workmanship.

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

5942-0130 GDC-350 Gas Sensor Monitor, NEMA 1 Housing, CO & Remote Combustible with Display by Bacharach

Bacharach's all new GDC-350 full-featured fixed gas monitors provide superior operation - standalone or as part of a larger system utilizing the standard analog outputs. This state-of-the-art instrument can detect a wide range of gases including carbon monoxide (CO), oxygen (O2), combustible gases, refrigerants and total volatile organic compounds (TVOCs). The GDC-350 provides a unique two sensor interface, allowing for multiple gases to be detected with onboard or remote sensors. Sensors can be located integral to the unit or remotely allowing for sensors to be placed directly in areas where potential leaks can occur. Bacharach s proprietary calibration algorithms extend the amount of time required between calibrations, reducing maintenance costs and lowering the overall cost of ownership for non-critical applications.

The GDC-350 has all the features and functionality for any application. LED alarm indicators visually indicate when alarm conditions are met and an audible alarm alerts nearby personnel. An onboard alpha numeric display shows gas readings in real time for each sensor. Integral dry contact relays are available to drive external audible / visual alarms, activate fans, or connect to building management and control systems. Installation and maintenance is simple and easy, reducing overall system cost. A pre-wired plug-in option is available for out-of-the-box operation. Simply plug the unit into any standard AC outlet for immediate detection and protection.

6010NK Handheld pH/ORP Meter Kit by Jenco

Includes:

• 6010N Handheld pH/ORP Meter
• 600P pH electrode, 3-ft cable, BNC connector, max temperature 60° C
• 6003C Extension Cable, 4-Pin to BNC & 1-Pin ATC, 3-ft

• Simultaneous displays pH or mV and temperature.
• 50 data set reviewable memory (6010M only).
• Convenient calibration with automatic buffer recognition of US and European buffer sets. Calibration data is stored in memory and ready for use on power up.
• Automatic or manual temperature compensation.
• Automatic lock mode and end point sensing are available to lock in stable readings.
• Automatic shutoff function (30 minutes of non-use).
• Battery life over 1000 hours.
• IP65 waterproof
• Low battery indicator.
• RoHS and CE compliant.

723-079-05-1K Eagle 2 Portable Monitor, CH4(IR Autoranging %LEL/%vol)/H2S(0-1000 ppm)/CO2(IR 0-60%vol), w/internal H2S dilution by RKI Instruments

Continuing in its legacy of durable and reliable gas detection and monitoring systems, RKI Instruments is proud to offer a new product in its popular Eagle portable gas detector series. The Eagle 2 can monitor up to 6 different gases and is equipped with several exclusive features that can only be found with the Eagle series. In addition, its large glove friendly push buttons and LCD screen ensure an ease of use when onsite. Rated intrinsically safe, the Eagle 2 is equipped with state of the art technologies that are not available with other competitive gas detectors and monitors.

Specialty Sensors

The Eagle 2 has a variety of available specialty sensors. Workers can use a photoionization detector for low or high range VOC detection and Fence Electrode Technology for humidity and contamination resistance. An infrared sensor is available for Co2, % LEL CH4, % Volume CH4, % LEL HC, and % Volume HC. Thermal conductivity sensors are available for % Volume H2 and % Volume CH4. The unit is also compatible with the smart plug and play toxic sensors for the detection of NH3, AsH3, CI2, HCN, PH3, and SO2. With the wide variety of sensors and gas detection available, the Eagle 2 can be customized to meet almost all worksite gas detection needs.

Exclusive Features

The monitor has a long internal pump that can draw samples for up to 125 feet. The pump features a low flow auto shut off and alarm. This allows operators to respond swiftly from a safe distance. The unit is multilingual with 5 different language preferences, and features an alkaline battery life of 18 hours or a NiMH life of 20 hours. To protect the integrity of the device and the configurations, the unit can be password protected. The Eagle 2 also has standard data logging capabilities for easy research, evaluation, and site monitoring. To reduce calibration costs and time, the unit features an automatic calibration option and a single gas calibration option.

The Eagle 2 is heavily protected from environmental conditions by a weather proof, chemical resistant RFI/EMI coated high impact polycarbonate/PBT blend enclosure. The enclosure also renders the unit water and dust resistant. Because of the enclosure, the Eagle 2 can function in 2 inches of water without leakage.

Eagle 2 Specifications

The portable and durable unit is lightweight at less than 4 pounds. Its dimensions are suitable for convenient carrying (9.5 L x 5.25 W x 5.875 H), and it features a conveniently placed durable top handle. The large easy to read display has a polyurethane overlay backlights on demand and when the alarm is activated. The 2 alarm channels are fully adjustable for the user and can be password protected. With a 95 dB buzzer and 4 high intensity LEDs, the alarm is sure not to be missed. The Eagle 2 is standard with a 2 year warranty for material and workmanship and a 1 year warranty for PID sensor.

*Please note we can only ship RKI products to customers within the United States

2811-707-001M EC 28 Gas Transmitter with MODBUS, Carbon Monoxide (CO), No Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

VN00483 X-am 8000 Multi-Gas Detector, LEL,PID,CO,H2S,O2,RFID&CLIP by Draeger

Clearance measurement was never this easy and convenient: The 1 to 7 gas detector detects toxic and flammable gases as well as vapors and oxygen all at once – either in pump or diffusion mode. Innovative signaling design and handy assistant functions ensure complete safety throughout the process.

Multi-gas detector

• 1- to 7 gas detection device
• for clearance measurement
• detection of toxic and combustible gases as well as vapors and oxygen

Specially designed for use with a pump, optimized for clearance measurement

The Draeger X-am® 8000 is equipped with a very powerful pump. It can be connected with hoses of up to 45 meters in length. A pump adapter makes it easy to switch between diffusion and pump mode at any time. This means the pump is only operated when you actually need it. That saves energy, reduces wear and tear, and extends the lifespan of the pump.

Handy and durable, the Draeger X-am® 8000 is intuitive to operate single-handedly using three function keys. The easy-to-read color display clearly lays out all the information for you.

The multi-gas detector also features advanced software functions including change of measurement gas for PID, CatEx and IR sensor during operation. This is based on an on-board library and a convenient assistant to hide unused sensor channels and adapt the flexible instrument to the measurement task.

Standard accessories include a sturdy shoulder strap so you can comfortably carry the X-am 8000. Thanks to its compact and robust construction, the device can withstand even the harshest conditions.

Clearance measurement, release and documentation in no time

The X-am 8000 effectively supports various applications with specially developed assistant functions that guide you through each process step by step. During clearance measurement, for example, the smart assistant calculates the necessary flooding time for the device and probe (FKM hose) based on parameters such as measuring gases, temperature limits, and the indicated hose length. Additionally, customer defined flooding times are also possible.

When monitoring for potentially high methane concentrations, an optional automatic measurement range switch makes it easier to take a reading: If the Cat-Ex sensor measures values above 100 % LEL, the display switches to the range of 0 to 100 vol %. A similar function to measure in % LEL and vol % simultaneously is also available for the IR EX ES sensor.

The DraegerSensor CatEx 125 PR Gas offers a special variant for the measuring gas methane, which enables measurements in the ppm range. The performance of selected sensors has been verified by an external approval body within the scope of the measurement performance approval (EN 60079-29-1) for combustible gases and vapors including methane, propane and n-nonane.

An additional useful tool is CSE Connect. It combines an app, specially designed for the X-am 8000, with a cloud-computing solution. Measuring jobs can be quickly and easily transferred to the app using an online application. An optional Bluetooth® module in the Draeger X-am 8000 enables measured values to be transferred automatically to the CSE Connect app. You can also easily and conveniently use the app to create measurement reports. This saves time and helps you manage your measuring tasks during clearance measurements more efficiently.

Clear signaling design

The signal system of the Draeger X-am 8000 is based on a clear color code, in accordance with the requirements of EN 60079-29-1, EN 45544-1 and EN 50104:

• Red light = gas alarm
• Yellow light = device-related alarm, e.g. low battery
• Green light = device is ready for use

The green glow of the D-Light allows you to see from a distance whether the device has been properly tested and is ready for use.

In case of an alarm, the X-am 8000 alerts you with colorful warning LEDs, a loud horn (100 dB(A) at a distance of 30 cm), and clearly palpable vibration. Optionally, four preset hazard symbols are available for the display which explicitly indicate the presence of explosive or toxic gas hazards, for example. This allows the user to easily recognize the type of hazard based purely on the symbol displayed.

The X-am 8000 is equipped with an impact detection system. The event report indicates whenever severe mechanical impacts have occurred that might result in functional impairments of the device or the sensors. These are also documented in the data logger. With this information, a device operator can specifically check the device. The instrument can also be locked after a detected impact as well.

Economical Fleet Management

Bumptest and calibration are carried out simply and quickly using the Draeger X-dock® calibrating station. Its low test gas consumption keeps operating costs to a minimum.

Its reporting function and numerous other useful features make the X-dock Manager PC software a smart addition to any fleet management operation. To identify devices in your fleet, you can either use tried and tested barcodes or an integrated RFID transponder.

Specialist for high and low hydrocarbon concentrations

To measure hard-to-detect hydrocarbons, you can fit the Draeger X-am 8000 with one of two high-performance PID sensors. The PID HC covers a measurement range of 0 to 2,000 ppm (isobutene). The PID LC ppb is particularly suited for a measurement range of 0 to 10 ppm (isobutene) with a high resolution in the range below 1 ppm.

For benzene-specific measurements, the X-am 8000 can be used with a pre-tube. The advantage: You only need one measuring device for this application, which significantly reduces the costs of purchasing, maintaining and transporting devices in use. The use of pre-tubes is supported by a built-in assistant.

Inductive charging protects against wear and tear

The X-am 8000 features inductive charging. This makes it easier to operate and increases the lifespan of the device. Issues like corrosion and contact problems in the charging cradle are a thing of the past. You can charge (outside of explosion-hazard zones) and measure at once, e.g, when using inside vehicles or on machinery.

The charging cradles can connect with one another, take up minimal space, and are compatible with existing Draeger X-am® series cradles.

Package Includes: Nano-Clip only

Part Number: P10492000PN

Multiflow Regulator

The 6000 Series regulators are for use with 58 liter and 103 liter non-refillable cylinders having a C-10 (5/8 -18 UNF) inlet connection. They may also be configured for use on returnable cylinders having pressures to 2400 PSIG. These aluminum-bodied, singlestage, piston-style regulators have eight flow settings from 0.2 LPM to 6 LPM. They are compatible with non-reactive as well as reactive gas mixtures like hydrogen sulfide, nitric oxide and ammonia. 1000 PSI gauges are used for non-refillable cyclinders and 3000 PSI gauges are used for refillable cylinders.

Part Number: 6660

6201-5107 IAM-100 Gas Detector, Remote Sensor/Faceplate, R410a 0-1000ppm, 110 VAC by Bacharach

The IAM-100 Gas Monitor from Bacharach offers exceptional continuos monitoring performance and flexibility at an economical price. By itself, or integrated into a comprehensive detection system, the IAM-100 is a scalable solution for detecting a variety of refrigerants, combustible gases and VOC gas leaks at the lowest possible cost.

Onboard LEDs illuminate when the sensor is in an alarm state while the unit's audible alarm alerts personnel in the area that levels have exceeded the desired limit. The audible alarm can be muted with the onboard silence switch. Integrated dual relays enable the IAM-100 to shut-off refrigerant or propane supply lines while the second relay can be used as a connection to a building BMS or BAS system.

The IAM-100 is an alarm threshold device. When the range of the sensor is exceeded, the detector will go into alarm. For example, a unit with a 1,000 ppm R-410a sensor will activate its alarm when the detected refrigerant meets or exceeds 1,000 ppm.

Features & Benefits:

• Real-time continuous gas detection that's scalable, reliable and affordable
• Ideal for commercial applications such as hotel rooms, apartments, dorms, hospitals, restaurant kitchens or battery charging rooms
• Detects refrigerants (at ?1,000 or ?10,000 ppm), TVOCs (at ?1,000 ppm), combustible gases and hydrocarbons (at ?5,000 ppm)
• Fast-responding, long-life sensors
• Integrated visual LED and audible alarms
• Two onboard relays to activate shut-off valves, exhaust fans, or connect to a BMS or fire panel
• Remote sensor with aesthetic faceplate available for discreet monitoring in decorative interiors

10160028 Altair 2XP Single Gas Detector, NO2, Gray, Sleep by MSA

Introducing the ALTAIR 2X Gas Detector from MSA; the first one or two gas detector that incorporates industry-leading XCell Sensor Technology to deliver unparalleled performance while drastically minimizing total cost of ownership, increasing durability and delivering enhanced worker safety, compliance and traceability.

The Altair 2X is also the first portable gas detector to introduce revolutionary XCell Pulse Technology. Based on proven science and advanced patented sensor capabilities, the Altair 2XP detector delivers the world's first stand-alone bump test. This allows a daily bump test to be performed without the need for calibration accessories or specific calibration gas.

ALTAIR 2XP Gas Detector with xCell Pulse Technology

ALTAIR 2xT Two-Tox Gas Detector

ALTAIR 2X Single Gas Detector

Features & Benefits

Low cost of ownership

• Fastest sensor response times, lowest calibration gas flow rate on the market
• 4-year expected instrument & sensor life
• 3-year warranty on instrument & most sensors (2 years on Cl2, NH3)
• Stand-alone bump tests reduce maintenance, increase productivity (ALTAIR 2XP only)
• 1 device can monitor 2 gases (ALTAIR 2XT only)

Increased safety awareness & real-time compliance

• Stand-alone bump test anytime, anywhere without specific calibration gas (ALTAIR 2XP only)
• Bump pass: green LED flash every 15s, large on-screen checkmark
• Bump fail or expiration: red LED flash every 15s, no checkmark
• End-of-sensor-life warning and alarm

Full-time traceability

• Records 75 alarm events
• 150+ hours of periodic data (ALTAIR 2X and 2XP)
• 100+ hours of periodic data (ALTAIR 2XT)
• Compatible with MSA GALAXY® GX2 Automated Test System and MSA Link Pro software

Rugged durability

• Tough over-molded rubber armor
• Survives multiple 25-ft drops onto concrete
• Agency-certified dust- and water-tight IP67 construction
• Intrinsically-safe design

Old Part Number: XD10675PN
New Part Number: X10675PN

72-5510RK Eagle Portable Monitor forLEL/Oxy/CO/NO/SO2,3-gas blk by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

72-2104RK-LCHR Rig Monitor System, with Beacon 410 Four Channel Controller, H2S Sensor 0 - 100 ppm, CO Sensor 0 - 300 ppm, Combustible Sensor 0 - 100% LEL with Cal Cup/Splash Guard and 25 Cable, Horn/Strobe, and 50 Power Cable with Battery Clamps by RKI Instruments

RKI Instruments is proud to announce our new RM series continuous gas monitors. These monitors are specifically designed for detection of H2S around temporary drilling rigs. All units include our long-life plug in electrochemical H2S sensor, range 0-100 ppm. All cable connections are protected by rugged strain relief cord grips, and sensors are mounted in an explosion proof enclosure that includes a convenient mounting bracket.

Features:

• H2S detection, 0-100 ppm range
• Explosion proof enclosure
• Convenient mounting bracket
• Easily installed and moveable
• Battery clamps for easy connection
• Powerful horn and strobe

Applications:

• Workover rigs
• Drilling rigs
• Fractionators
• Water reclamation
• Pumpers
• Water haulers
• Exploration

*Please note we can only ship RKI products to customers within the United States