All Products

M5-XW0Y-A-P-D-B-N-00 GasAlertMicro 5 Detector % LEL, O2, H2S, CO - Alkaline Batteries and Pump - Black Housing by BW Technologies

The GasAlertMicro 5 Series is the most customizable gas monitoring series on the market. With an extensive selection of models, user options, and instrument settings, this multi-gas detector series is an industry leader. BW Technologies by Honeywell recognizes that not all worksites can operate with a one size fits all model of gas detection devices. With the introduction of the GasAlertMicro 5 Series multi-gas detectors, worksites, managers, and users can utilize the customizable features to ensure that the instrument meets their specific worksite needs.

GasAlertMicro 5 Series models

This multi-gas monitor series is available in several models: the standard toxic gas model, a PID model for detection of VOCs, or an IR model for CO2 detection. The unit accurately and reliably identifies up to five atmospheric hazards simultaneously and can rapidly switch from diffusion mode to the optional integrated pump.

Each model of GasAlertMicro 5 Series has several distinct features. With the GasAlertMicro 5 Series, the standard toxic gas model, users can monitor several standard gases with a plug in electrochemical cell sensor and catalytic cell sensor and a typical battery life of 20 hours (AA Alkaline rechargeable). The GasAlertMicro 5 PID is standard with several gas detections, a plug in electrochemical cell sensor and photoionization detector, and a battery life of approximately 15 hours (AA Alkaline rechargeable). Finally, the GasAlertMicro 5 IR features specific gas detection ranges, a plug in electrochemical cell sensor, a catalytic cell sensor, and an infrared sensor for carbon dioxide monitoring. This model also has a battery life of approximately 15 and AA Alkaline rechargeable batteries. For more information about available sensor configurations, please contact BW Technologies by Honeywell.

Exclusive features

Each GasAlertMicro 5 Series device features several exclusive features including a triple alarm system, raised glove-friendly buttons, a large easy to read display, stainless steel alligator clip, visual filter inspection, and automatic activation tests. When the unit is activated, the gas detector will automatically test for sensor integrity, circuitry, and battery. This continuous and reliable testing process ensures that the integrity and dependability of the device is never a concern.

BW Technologies by Honeywell also recognizes the unique needs of the various industries with environmental hazards. With each industry anticipating a separate set of possible dangers, the ability to customize safety devices is critical.

Users and worksite managers will be comforted to know their GasAlertMicro 5 series model is fully customizable. Customizable features include STEL intervals, TWA methods, sensor activation, alarms, display settings, record keeping, pumps, combustible gas measurements, start up calibration, backlights, activation modes, calibration levels, daily bump tests, and languages. To protect the integrity of the user settings and the safety of the gas monitoring device, the GasAlertMicro 5 device features a passcode function to prevent unauthorized manipulation of settings.

Accessories

The GasAlertMicro 5 Series is also compatible with BW's MicroDock II automatic test and calibration system. Users may purchase additional accessories to help fully tailor the gas detection unit to their needs. Accessories include an integral pump and battery charger, a confined space kit, a belt holster, and a collapsible sampling probe.

Part Number: M5XW0YAPDBN00

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

9250MKA D.O. & Temperature Handheld Polarographic Meter with Memory & RS-232 Kit by Jenco

Includes:

• 9250M D.O. & Temperature Handheld Polarographic Meter with Memory & RS-232
• LD-900-8-DO Stainless Steel Field Probe with 8-Pin Connector 8-Pin Connector & 10-ft Cable
• LD-900-03A Membrane Kit with 6 Caps & KCL Solution

• Clear LCD displays dissolved oxygen as percent air saturation or as parts per thousand simultaneously with temperature.
• Convenient one point calibration for dissolved oxygen. Calibration data is stored in memory and is ready for use on power up.
• User selectable salinity and pressure compensated dissolved oxygen readings.
• Work with accurate and reliable polarographic dissolved oxygen probes.
• Inclined back provides ideal viewing angle for benchtop use.
• 50 memory storage of dissolved oxygen with temperature reading with memory location ID.
• RS-232 computer interface with software.
• IP65 waterproof.
• AC adaptor or battery power (low battery indicator).

Gasmaster Control Panel for Gas and Fire Monitoring

Crowcon Detection Instruments is a global leader in gas detection and safety equipment. With over 40 years of experience in research and technology, Crowcon is consistently leading the industry in design innovation. By integrating historical successes with advances in modern technology, Crowcon is able to consistently produce high quality products that meet today s challenging environments.

The Gasmaster is an innovative self-contained control panel that monitors gas and fire hazards. Its exclusive features allow the control panel to be flexible enough to fit most industrial applications. More importantly, its outstanding performance and leading technology make this panel an industry leader.

Exclusive Gasmaster Features

Crowcon sGasmaster contains numerous features that outperform the competition in gas detection and safety standards:

• Easy to use control features
• Easy to read backlit LCD display
• Unparalleled flexibility and compatibility with existing equipment
• Reliable alarm and safety features

Easy to Use

The Gasmaster is incredibly easy to read and operate. The front mounted display simultaneously broadcasts all of the appropriate gas levels while indicating the system status check. The front panel also houses the buttons that control the systems operations. All features of the Gasmaster, including recalibration, can be controlled by these easy to operate keys. With the simple push of a button, any user can easily operate the system s features. The Gasmaster s system s software was also designed with ease of use in mind. The software enables reconfiguration and datalogging instantaneously and requires minimal training.

The backlit LCD display screen provides all of the necessary safety information without overwhelming the user. Utilizing a large clear screen, the alphanumeric display reads the gas levels, displays the system status, and illuminates an alarm bar when necessary.

Flexible and Adaptable

The state of the art Gasmaster is incredibly versatile and flexible. The unit can monitor and control virtually any combination of gas and fire detectors. The unit also offers a variety of outputs

SP200B Switchable Passive Oscilloscope Probe, 200MHz, 1.2M Cable Length by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

G888C-030124006010K G888C gas monitor, 5 year O2 (lead free), CO, NO2, IR CO2, includes calibration cap, charging cradle with wall power adapter and value kit (cal gas, regulator, carrying case) by GfG

The development of the Microtector III G888 focused on the requirements of a modern multi-gas detection instrument for use in personal protection. The result is a multi-gas warning device that is safe, robust and practical and has proven itself in daily working conditions.

Advantages

Safety through quality and functionality

Equipped with high-quality, precise and durable sensors that can be individually adapted to your requirements. Multitude of gas-combinations can be identified to ensure maximum safety of employees.

The well thought-out design of the housing and the menu navigation eases the operation of the multi-gas warning device under difficult conditions. This device features a rotating display, easily turning 180 degrees with just one click. For working in poorly lit conditions, the device conveniently features an explosion-protected LED light.

Designed for difficult working conditions

Sometimes there is a need to work in challenging environments; the Microtector III G888 is equipped to withstand such challenges. Ex zone 1 certified, the Microtector III G888 is dusttight and water-resistant in accordance to the IP 67 protection class. The rubberized polycarbonate housing makes the detector shock-resistant and will keep your device safe in case of a fall. It is also comfortable to wear, weighing only 275g.

Suitable for long operating times

Depending on the sensor equipment and configuration, the Microtector III G888 has an operating time of up to 65 hours.

Remote monitoring keeps employees safe

If the G888 with the radio module is used, teams can be monitored centrally via the portable GfG-Link or using a computer and an USB dongle. Information regarding the measured gas concentrations, alarm levels and the status of the man-down alarm will then be available in real time.

Be prepared for an emergency

In the event of an emergency it is always good to be prepared. The Microtector III G888 is able to simulate an alarm of any gas concentration, in order to train and prepare for a variety of emergency situations.

Maintenance and documentation

The test and docking stations for the Microtector III G888 not only allow location-independent, daily bump tests and regular functional checks, as well as the complete documentation.

G888 - the team player

The Microtector III G888 offers optimum individual protection for everyone working in hazardous and/or enclosed areas. When measuring releases of gas or searching for a gas leak, it is recommended to use the Polytectors III G999 from GfG, which has a built-in pump. The advantage: both devices can be remotely monitored by a computer or GfG-Link.

FP-300AGZS FP-300 Paper Tape Machine, C4F6 / C5F8, 0-5.00 ppm by RKI Instruments

RKI s paper tape monitors utilize highly sensitive colorimetric tapes to achieve interference free detection at low PPB and PPM levels Ammonia, Arsine, Chlorine, Diborane, Hydrogen Chloride, Hydrogen Fluoride, Hydrogen Sulfide, Phosphine, Silane. The FP-300 is equipped with an easily replaceable tape. This model is equipped with a digital display showing the type of gas and concentration in PPM or PPB. The FP-300 will also display remaining tape life as well as an end of tape alarm.

The FP-300 has audible and visual alarms, as well as alarm relay contacts and 4-20mA output. A unique tape saver mode extends tape life in applications where high background gas levels may be present.

The FP-300 meets and exceeds OSHA and NIOSH compliance requirements, and does not respond to interfering gases (hydrocarbons, alcohols, solvents, CO, etc.) that may be present in industrial/manufacturing environments.

Features:

• Small and compact
• Highly sensitive and ideal for low gas concentrations (ppb detection)
• Interference-free detection
• Easy detection tape replacement with plug-in cassette
• Tape remainder display and tape end warning alarm provided
• Easily transportable

Applications:

• Scrubbers
• Environmental Monitoring
• Semiconductor Fabs
• Manufacturing
• Detecting uncaptured gas from scrubber

*Please note we can only ship RKI products to customers within the United States

Part Number: CP-KF

Part Number: DXFILTERS

0560 4101 410-1 Pocket Pro Air Velocity & Temperature Meter by Testo

testo 410-1 measures air speed and temperature. It is ideal for quick spot checks at air outlets on account of its integrated measurement with the 40mm vane. Timed mean calculation is possible. In addition to air speed and temperature, testo 410-2 also measures air moisture. Testo's very own, patented humidity sensor guarantees accurate readings. In this way, air conditions can be reliably checked.

• Flow velocity measuring instrument with temperature measurement
• Integrated measurement with 40 mm vane
• Timed mean value calculation
• Hold function and max./min. values
• Windchill calculation for outside areas (perceived temperature)
• Display illumination
• Protective cap for safe storage
• Including wrist strap, belt holder and calibration protocol

Part Number: 103L-50-100

BW Technologies Auxiliary Filter Kit (Complete with Filter Adaptor and 5 Filters)

To ensure proper maintenance and operation of BW Technologies gas detection device, users will need to perform regular inspections and maintenance. Depending on the frequency of use, filters and screens may need to be replaced. A filter replacement kit is ideal to have on hand so that after inspection, a user can immediately replace the filters if needed. Clean filters help to protect the device and its internal circuitry from dust, debris, and moisture. This particular kit includes a filter adaptor and 5 filters. A clean filter is critical to extending the life of any gas detection instrument.

Part Number: MCAFK1

SO3371-P Sodium Oxalate, 0.0250M, 500mL by AquaPhoenix

• APHA for Nitrogen (Nitrite), 4500-B

Specifications

• Packaging Type: Glass
• Size: 500 mL

Part Number: M5-AF-K2-100