All Products

3622-075 D-ReX PoS Gas Detector with 5 relays, Phosphine (PH3) MK478-10, 0 - 1 ppm by GfG

Not all gases can be monitored directly at the measuring point. This may be because the maintenance of a remote sensor would be too complicated or because the target gas has to be broken down into detectable components first. This can be done using a pyrolyzer.

In these cases, the D-ReX PoS with its integrated pump is an ideal solution. The point of sampling (PoS) can be up to 100 feet / 30 meters away from the D-ReX. This also applies to the length of the recirculation hose.

Available Accessory:

• DIN rail
• PTFE hose
• Various particle filters
• Push-Pull plug-in adapter
• Angle braces

Features:

• 5x internal relays (form C, configurable)
• Smart sensors for more than 60 gases
• Hot-swappable smart sensor cartridge
• Tool-free maintenance
• Power-over-Ethernet (PoE) communication
• Web server for browser access
• Password-protected menu
• Interface: Analog outlet: 4 20 mA output; Digital: RS-485 (Modbus/RTU); 10/100 Mbit Ethernet (Modbus/TCP)
• Bright status and alarm LEDs
• Data logger to review sensor and alarm history
• Marked as FCC, CE, IC and UKCA

6302-1152 MGS-450 Gas Detector - IP41, 3 x Relays, Analog Output, Modbus Output, Audible & Visual Alarms - R1234ze, 0-1,000ppm, Semi-conductor by Bacharach

Bacharach's MGS-400 Gas Detectors makes compliance with mechanical equipment room and refrigeration safety codes simple and easy, saving time and money on equipment and installation. Using the MGS-400 App, users can intuitively use, commission and maintain their gas detection system without the need for specialty training or tools. Pre-calibrated sensor modules simplify maintenance, take minutes to exchange and do not require the use of calibration gas. The MGS-400 sensors can trigger additional audio-visual alarms and act as a standalone gas detection system, or integrate easily into a BMS / BAS or with Bacharach's optional MGS-408 Gas Detection Controller.

Features

• Mobile App Interface
• Pre-calibrated Sensors
• Semi-automated Calibration
• Remote Sensor Option
• Temperature-Compensated Measurement
• Low Temperature Performance
• Digital Communications
• Analog Outputs
• Relay outputs
• Audio & Visual Alarms
• Multiple Cable Entries and Terminals

Benefits

• Quick, easy and intuitive commissioning, configuration and maintenance requires no special training. No tools required to set alarm levels and behavior
• Fast and easy sensor maintenance. Eliminates need for calibration gas.
• Easy calibration process with mobile app. Generate calibration certificates for documentation.
• Locate the sensor element in hard-to-reach areas and the base unit where convenient for electrical and communication wiring (MGS-460)
• Mitigates false alarms and optimizes accuracy in refrigeration applications.
• Suitable for use in cold rooms and freezers down to -40° F/C.
• Integrate with local BMS/BAS via Modbus RTU
• For current or voltage output to legacy systems (MGS-450/460)
• 3 relays available for alarm and fault events to active horn/strobes and ventilation (MGS-450, MGS-460)
• On-board alarm notification supports compliance with ASHRAE 15 / EN 378
• Quick and easy installation of all wiring; daisy-chain power and digital communications.

72-6AIX-A GX-6000 Six Sensor Sample Draw Gas Monitor, LEL / O2 / H2S / CO / SO2, with Alkaline Battery Pack by RKI Instruments

Simply put, the GX-6000 is a game changer. This powerful hand-held instrument is capable of simultaneously monitoring up to 6 gases. In addition to the standard 4 confined space gases which include combustibles, O2, CO, & H2S, the GX-6000 has 2 additional smart channels that accept PID, IR or super toxic sensors. Equipped with a strong internal sample pump, a man-down alarm, a panic alarm, an LED flashlight, and large auto rotating LCD display, the GX-6000 can operate as a single gas PID unit or a multifunctional tool utilizing all 6 channels. The GX-6000 with a PID sensor will come equipped with a library of over 600 VOC gases to choose from as standard. Choosing from the library is easy with a personalized favorites list of 30 commonly used VOC's as well as a list of 8 of the most recently used VOC's.

The GX-6000 has a rugged design built for the nastiest environments. It is equipped with a removable impact-resistant rubber boot and a dust and water resistant enclosure with an IP-67 rating. With 5 bright LED lights on 3 sides of the instrument, alarms are easily seen from a variety of perspectives. With vibration and loud audible alarm, GX-6000 will easily alert users when needed.

Features

• Monitor up to 6 gases
• 2 smart sensor slots auto recognize PID, IR, and super toxic sensors
• 5 Operating modes: normal, leak check, inert, snap log and bar hole
• Library of over 600 VOCs
• PPM Leak Check mode
• Man-down and panic alarms
• Auto display rotation
• LED Light source
• Internal sample pump
• Glove friendly glow in the dark buttons
• Light weight, small, rugged IP-67 design
• Interchangeable battery packs Li-ion / alkaline
• Operates up to 14 hours on Li-ion battery pack, fully recharges in 3 hours
• Field replaceable sensors, batteries and filters

Applications

• Confined space entry
• Hazmat response teams
• Arson investigation
• Remediation sites
• Perimeter monitoring
• Leak detection
• Landfill monitoring
• Wing tank entry

*Please note we can only ship RKI products to customers within the United States

VPX-L1731100G1C Ventis Pro Series, LEL (Methane), CO, Cl2, O2, Li-ion, Desktop Charger, None, Black, China Ex, CPA, LENS Wireless, Chinese by Industrial Scientific

Detect up to five gases simultaneously with the rugged, wireless, Ventis® Pro5 Multi-Gas Monitor. With Ventis Pro5, safety goes beyond the gas detector whether you need team-based alarm sharing, remote monitoring with location details, or both. The monitor is also backed by a Guaranteed for Life™ warranty.

• Eliminate the need for two pieces of equipment by using Ventis Pro5 for personal monitoring and confined space entry.
• Train workers on one, multi-purpose gas monitor and reduce the risk and investment of having different devices in the field.
• Improve team and site safety by locally sharing alarms and gas readings between wirelessly connected Ventis Pro5 monitors.
• Get real-time location and alarm data directly from Ventis Pro5 gas monitors to a designated safety contact with the optional cellular or wi-fi battery pack.
• Reinforce safe behavior with programmable alarm action messages like "EVACUATE" or "VENTILATE" based on alarm level.
• Simplify the user experience with the ability to hide unnecessary screens based on user needs, role, industry, or site.

1324-0401 IR-148 Infrared Gas Monitor, Four Point, N2O (0-1000 ppm) by Honeywell Analytics

The Model IR-148 is an infrared gas monitor that detects toxic and combustible gases as well as solvents. It uses infrared sensing technology, allowing accurate measurement of target gas vapors with minimum interference from other vapors. The Model IR-148 is supplied as a wall mount unit configured for 1, 4 or 8 sampling points measuring down to 1 part per million (ppm). It has two available analog outputs, each which is software selectable between 10% and 100% of full scale: 4-20mA, isolated, current sourcing, and 0-10 VDC. Multiple gas calibrations are available.

Additional Features and Benefits:

• Infrared sensing technology
• Accurate measurement of target gas vapors with minimum interference
• Optional relay module can be configured for 1, 2 or 3 alarm levels
• 4-20mA

Quick Specs:

• Response: Updated reading every 7 seconds
• Operating temperature: 0-50°C, 32-122°F
• Relative humidity: 0-99% non-condensing (no effect on reading)

*Please note we can only ship RKI products to customers within the United States

Set of 2 straps which in combination with the chest harness plate enable the detector to be worn on the chest.

MX6-L72A6211 MX6 iBrid Multi-Gas Monitor, LEL (Methane), Cl2, H2S, HCl, NH3, Lithium-ion Extended Range Battery, UL/CSA/ATEX/IECEx, Pump, English by Industrial Scientific

The MX6 iBrid® is more than an intelligent hybrid of Industrial Scientific's best monitoring technologies—it's the most adaptable six-gas monitor on the market. With hundreds of possible sensor combinations, and a robust list of available configuration settings, the MX6 iBrid is ready to monitor oxygen, toxic and combustible gas, and volatile organic compounds (VOCs).

As your work changes, so can your MX6 iBrid. It uses five sensor slots to detect up to six gases. Each of those sensor slots accepts a variety of sensors, which means you can use the instrument with a PID sensor one day and an infrared sensor the next. What's more, settings allow you to adapt the instrument's behavior for your application. If you need to use a benzene PID response factor for one application, and butadiene for others, the familiar menu structure will allow you to quickly change settings.

The rugged MX6 iBrid carries our Guaranteed for Life™ warranty and is compatible with DSX™ Docking Stations. With a DSX Docking Station, maintenance is simplified and data becomes more than a spreadsheet filled with logged readings. Proactively manage your gas detection fleet—track trends, know when instrument maintenance will be required, and understand how your MX6 iBrid instruments are being used.

• 24 "Plug-and-Play" field-replaceable sensors including PID and Infrared options
• Up to 6 gases monitored simultaneously
• Simple, user-friendly, customizable, menu-driven navigation
• Five-way navigation button
• Durable, concussion-proof overmold
• Optional integral sampling pump with strong 30.5 meter (100 feet) sample draw
• Full-color graphic LCD is highly visible in a variety of lighting conditions
• Powerful, 95 dB audible alarm

CC22-702-DM CC 22 Series Fixed Transmitter with Propane (C₃H₈) Sensor, 0 - 100% LEL Range, Display / Modbus by GfG

Are you looking for an innovative and cost-effective transmitter for combustible gases, but without the need for explosion protection? Then a GfG 22 series transmitter is the right choice.

Time-proven and innovative

The CC 22 works according to the heat of reaction principle, a proven method for measuring combustible gases. The transmitters are fitted with high-performance electronics for voltage stabilization, processing of readings, and temperature compensation. Follow-up costs are minimized thanks to the long lifespan of the sensors.

Universal signal transmission

Either an analog or digital output signal can be transmitted by the CC 22 by means of a Modbus interface. Due to the different types of signal transmission, a 22 series transmitter can be connected to almost any gas detection system, also as an extra measuring point or as a replacement transmitter on existing systems.

Signal processing

The embedded software of the CC 22 linearises the measuring signal and compensates for the effects of temperature. As a result, correct readings are transmitted even with weather related fluctuations in temperature. The software allows problems to be detected, and the Modbus version also indicates any required service or maintenance work.

Weather protection

A weatherproof housing not only protects transmitters against exposure to wind and weather, but also against contamination and excessive temperatures caused by direct sunlight.

Optional colored graphic display

The clear graphic display of the CC 22 is self explanatory and allows you to read off the current status and other important information with ease. The display enables you to navigate effortlessly through the unit's concise menu and to change settings or even calibrate, depending on your user authorization. In the event of an alarm, the display will turn red.

Operation buttons

The buttons on the transmitter allow the unit to be calibrated and settings to be adjusted through the menu as needed.

The application areas of the dust and water-protected structure range from production and storage areas to disposal sites, biogas plants, mines and oil rigs.

Calibration adapter

In order to perform regular bump tests, a calibration adapter is used on the transmitter, which ensures a uniform and secure supply of gas.

Easy and convenient service

GfG offers full after-the-sale commissioning and field service support.

Features

• Uses the catalytic combustion principle
• Long service life of the sensors
• High efficiency and low follow-up costs
• Sturdy plastic housing (IP 54)
• Cost effective single-man adjustment
• Affordable solution for many measuring tasks

CC22-761-D CC 22 Series Fixed Transmitter with n-Hexane (C₆H₁₄) Sensor, 0 - 100% LEL Range, Display / 4-20 mA by GfG

Are you looking for an innovative and cost-effective transmitter for combustible gases, but without the need for explosion protection? Then a GfG 22 series transmitter is the right choice.

Time-proven and innovative

The CC 22 works according to the heat of reaction principle, a proven method for measuring combustible gases. The transmitters are fitted with high-performance electronics for voltage stabilization, processing of readings, and temperature compensation. Follow-up costs are minimized thanks to the long lifespan of the sensors.

Universal signal transmission

Either an analog or digital output signal can be transmitted by the CC 22 by means of a Modbus interface. Due to the different types of signal transmission, a 22 series transmitter can be connected to almost any gas detection system, also as an extra measuring point or as a replacement transmitter on existing systems.

Signal processing

The embedded software of the CC 22 linearises the measuring signal and compensates for the effects of temperature. As a result, correct readings are transmitted even with weather related fluctuations in temperature. The software allows problems to be detected, and the Modbus version also indicates any required service or maintenance work.

Weather protection

A weatherproof housing not only protects transmitters against exposure to wind and weather, but also against contamination and excessive temperatures caused by direct sunlight.

Optional colored graphic display

The clear graphic display of the CC 22 is self explanatory and allows you to read off the current status and other important information with ease. The display enables you to navigate effortlessly through the unit's concise menu and to change settings or even calibrate, depending on your user authorization. In the event of an alarm, the display will turn red.

Operation buttons

The buttons on the transmitter allow the unit to be calibrated and settings to be adjusted through the menu as needed.

The application areas of the dust and water-protected structure range from production and storage areas to disposal sites, biogas plants, mines and oil rigs.

Calibration adapter

In order to perform regular bump tests, a calibration adapter is used on the transmitter, which ensures a uniform and secure supply of gas.

Easy and convenient service

GfG offers full after-the-sale commissioning and field service support.

Features

• Uses the catalytic combustion principle
• Long service life of the sensors
• High efficiency and low follow-up costs
• Sturdy plastic housing (IP 54)
• Cost effective single-man adjustment
• Affordable solution for many measuring tasks

35612-91 Replacement Calibration Salt, 75% RH by Digi-Sense

Keep your hygrometer running smoothly with these replacement items.

72-6AZB-C GX-6000 Six Sensor Sample Draw Gas Monitor, LEL/Oxy/H2S/CO/VOC(10.0 ev)/VOC(6K ppm 10.6 eV),w/Li-ion bat pack/100-240 VAC charger by RKI Instruments

Simply put, the GX-6000 is a game changer. This powerful hand-held instrument is capable of simultaneously monitoring up to 6 gases. In addition to the standard 4 confined space gases which include combustibles, O2, CO, & H2S, the GX-6000 has 2 additional smart channels that accept PID, IR or super toxic sensors. Equipped with a strong internal sample pump, a man-down alarm, a panic alarm, an LED flashlight, and large auto rotating LCD display, the GX-6000 can operate as a single gas PID unit or a multifunctional tool utilizing all 6 channels. The GX-6000 with a PID sensor will come equipped with a library of over 600 VOC gases to choose from as standard. Choosing from the library is easy with a personalized favorites list of 30 commonly used VOC's as well as a list of 8 of the most recently used VOC's.

The GX-6000 has a rugged design built for the nastiest environments. It is equipped with a removable impact-resistant rubber boot and a dust and water resistant enclosure with an IP-67 rating. With 5 bright LED lights on 3 sides of the instrument, alarms are easily seen from a variety of perspectives. With vibration and loud audible alarm, GX-6000 will easily alert users when needed.

Features

• Monitor up to 6 gases
• 2 smart sensor slots auto recognize PID, IR, and super toxic sensors
• 5 Operating modes: normal, leak check, inert, snap log and bar hole
• Library of over 600 VOCs
• PPM Leak Check mode
• Man-down and panic alarms
• Auto display rotation
• LED Light source
• Internal sample pump
• Glove friendly glow in the dark buttons
• Light weight, small, rugged IP-67 design
• Interchangeable battery packs Li-ion / alkaline
• Operates up to 14 hours on Li-ion battery pack, fully recharges in 3 hours
• Field replaceable sensors, batteries and filters

Applications

• Confined space entry
• Hazmat response teams
• Arson investigation
• Remediation sites
• Perimeter monitoring
• Leak detection
• Landfill monitoring
• Wing tank entry

*Please note we can only ship RKI products to customers within the United States

10-100-10 Ammonia Colorimetric Gas Detection Tube, 5 - 100 ppmv (10 Tubes / Box) by RAE Systems

RAE Systems colorimetric gas detection tubes enable quick, on-the-spot measurement of a wide range of toxic and combustible gases and vapors. RAE Systems tubes are easy to read, and provide a sharp, clear color change directly corresponding to the concentration of gas present. RAE Systems tubes are compatible with the RAE Systems piston hand pump, a reliable way to draw samples of an exact volume required for the most accurate measurements.

Key Features

• Wide assortment of tubes available to detect over 300 gases and vapors
• Easyto use, even in multiple layers of gloves
• Easy-to-read with sharp,clearcolorchange
• No calibration or other maintenance required

Applications

• Oil and gas
• Chemicals and petrochemicals
• Agriculture and pestcontro
• Food and beverage production
• Environmental protection
• Fire service
• HazMat response
• Nationalsecurity

CC22-751-DM CC 22 Series Fixed Transmitter with Nonane (C9H₂0) Sensor, 0 - 100% LEL Range, Display / Modbus by GfG

Are you looking for an innovative and cost-effective transmitter for combustible gases, but without the need for explosion protection? Then a GfG 22 series transmitter is the right choice.

Time-proven and innovative

The CC 22 works according to the heat of reaction principle, a proven method for measuring combustible gases. The transmitters are fitted with high-performance electronics for voltage stabilization, processing of readings, and temperature compensation. Follow-up costs are minimized thanks to the long lifespan of the sensors.

Universal signal transmission

Either an analog or digital output signal can be transmitted by the CC 22 by means of a Modbus interface. Due to the different types of signal transmission, a 22 series transmitter can be connected to almost any gas detection system, also as an extra measuring point or as a replacement transmitter on existing systems.

Signal processing

The embedded software of the CC 22 linearises the measuring signal and compensates for the effects of temperature. As a result, correct readings are transmitted even with weather related fluctuations in temperature. The software allows problems to be detected, and the Modbus version also indicates any required service or maintenance work.

Weather protection

A weatherproof housing not only protects transmitters against exposure to wind and weather, but also against contamination and excessive temperatures caused by direct sunlight.

Optional colored graphic display

The clear graphic display of the CC 22 is self explanatory and allows you to read off the current status and other important information with ease. The display enables you to navigate effortlessly through the unit's concise menu and to change settings or even calibrate, depending on your user authorization. In the event of an alarm, the display will turn red.

Operation buttons

The buttons on the transmitter allow the unit to be calibrated and settings to be adjusted through the menu as needed.

The application areas of the dust and water-protected structure range from production and storage areas to disposal sites, biogas plants, mines and oil rigs.

Calibration adapter

In order to perform regular bump tests, a calibration adapter is used on the transmitter, which ensures a uniform and secure supply of gas.

Easy and convenient service

GfG offers full after-the-sale commissioning and field service support.

Features

• Uses the catalytic combustion principle
• Long service life of the sensors
• High efficiency and low follow-up costs
• Sturdy plastic housing (IP 54)
• Cost effective single-man adjustment
• Affordable solution for many measuring tasks

MX6-M143Q21B MX6 iBrid Multi-Gas Monitor, CH4 (0-5%), CO, NO2, O2, CO2 (IR), Lithium-ion Extended Range Battery, UL/CSA/ATEX/IECEx, Pump, Czech by Industrial Scientific

The MX6 iBrid® is more than an intelligent hybrid of Industrial Scientific's best monitoring technologies—it's the most adaptable six-gas monitor on the market. With hundreds of possible sensor combinations, and a robust list of available configuration settings, the MX6 iBrid is ready to monitor oxygen, toxic and combustible gas, and volatile organic compounds (VOCs).

As your work changes, so can your MX6 iBrid. It uses five sensor slots to detect up to six gases. Each of those sensor slots accepts a variety of sensors, which means you can use the instrument with a PID sensor one day and an infrared sensor the next. What's more, settings allow you to adapt the instrument's behavior for your application. If you need to use a benzene PID response factor for one application, and butadiene for others, the familiar menu structure will allow you to quickly change settings.

The rugged MX6 iBrid carries our Guaranteed for Life™ warranty and is compatible with DSX™ Docking Stations. With a DSX Docking Station, maintenance is simplified and data becomes more than a spreadsheet filled with logged readings. Proactively manage your gas detection fleet—track trends, know when instrument maintenance will be required, and understand how your MX6 iBrid instruments are being used.

• 24 "Plug-and-Play" field-replaceable sensors including PID and Infrared options
• Up to 6 gases monitored simultaneously
• Simple, user-friendly, customizable, menu-driven navigation
• Five-way navigation button
• Durable, concussion-proof overmold
• Optional integral sampling pump with strong 30.5 meter (100 feet) sample draw
• Full-color graphic LCD is highly visible in a variety of lighting conditions
• Powerful, 95 dB audible alarm

Part Number: F105315PM1

GS-AN-B-004-G Gasman Single Gas Monitor, 0-20ppm Chlorine, Non Rechargable Battery (single use), Spanish ATEX by Crowcon

For over 40 years, Crowcon Detection Instruments has produced state of the art gas detection devices for personal and industrial use. Building upon their reputation for reliable and innovative gas monitoring products, Crowcon introduces the Gasman personal gas monitor. Its lightweight and compact design is convenient for jobsites where workers need not be weighed down by excessive bulk and equipment. The unit conveniently clips to a pocket or helmet and operates continuously.

The Gasman personal gas monitor has numerous convenient features such as:

• One button technology
• Backlit LCD display
• Durable polycarbonate casing
• Quick response triple alert system
• Compact and lightweight design

Easy to Use

The Gasman s true one button technology is an ideal and simple design. The large glove friendly button is mounted on the front of the unit for easy access and controls all of the unit s programmable features. Also on the front, the Gasman s easy to read backlit LCD screen indicates gas readings and the battery status. The simple screen provides a clear indication of the unit s operation status. It will also alert the user 30 days in advance of when a calibration test is due. With a simple and intuitive design, Crowcon has produced a gas detector that reduces the complexities of workplace safety, and ensures workers in a straightforward manner that their equipment is on and operational.

Triple Alarm System

This portable single gas detection system features a triple alarm system that is sure to alert the user and anyone in the vicinity. The visible alarm utilizes a dual red and blue flashing LED light, and the unit houses an internal vibrating alert system. These two indicators allow for visual recognition in loud environments and working conditions. The alarm system also features a programmable audible alarm at 95 decibels. The unit is capable of a variety of alarm tones, and users can select which tone may be best for the individual workplace setting. The triple alarm system with multiple sensory indicators is sure to be noticed in almost any work environment.

Specifications

The Gasman single gas monitor is lightweight and compact, weighing less than 135 grams and with dimensions of 90 x 48 x 24 mm. The unit is available with a wide variety of gas sensors which feature various detection and alarm levels. The unit also features a quick response time of 20 seconds for flammable and toxic gases or 10 seconds for oxygen. Its datalogging feature has approximately 900 hours of storage and all events are time stamped. The battery life for this unit is incredible with 12 hours of runtime on a Rechargeable battery battery or up to 2 years on a non-Rechargeable battery.

EC22-706-D EC 22 Fixed Transmitter with Carbon Monoxide (CO) Sensor, 0 - 2,000 ppm Range, Display / 4-20 mA by GfG

The EC 22 Series are innovative and cost-effective transmitters for the detection of toxic gases or oxygen levels, but without the need for explosion protection.

Time-proven and innovative

The EC 22 is equipped with high quality GfG sensors. The transmitters are fitted with high-performance electronics for voltage stabilization, processing of readings, and temperature compensation. Follow up costs are minimized thanks to the long lifespan of the sensors.

Universal signal transmission

Either an analog or digital output signal can be transmitted by the EC 22 by means of a Modbus interface. Due to the different types of signal transmission, a transmitter from the 22 series can be connected to almost any gas detecting system, also as a supplementary or replacement transmitter on existing systems.

Signal processing

The embedded software of the EC 22 linearizes the measuring signal and compensates for the effects of temperature. As a result, correct readings are transmitted even with weather related fluctuations in temperature. In addition, the transmitter also offers the option of transmitting service, maintenance, and error messages to a connected gas measuring computer.

Weather protection

A weatherproof housing not only protects transmitters against exposure to wind and weather, but also against contamination and excessive temperatures caused by direct sunlight.

Optional colored graphic display and horn

The clear graphic display of the EC 22 is self explanatory and allows you to read the current status and other important information with ease. The display enables you to navigate effortlessly through the unit s concise menu and to change settings or even calibrate, depending on your user authorization. In the event of an alarm the display changes color from green to red. Two LEDs indicate the status.

Operation buttons

The buttons on the transmitter allow the unit to be calibrated and settings to be adjusted through the menu as needed.

Calibration adapter

In order to perform regular bump tests, a calibration adapter is used on the transmitter, which ensures a uniform and secure supply of gas.

Easy and convenient service

GfG offers full after-the-sale commissioning and field service support.

Features

• Long service life of the sensors
• High efficiency and low follow-up costs
• Sturdy plastic housing (IP-54)
• Cost effective single-man adjustment
• Affordable solution for many measuring tasks

2108N5002H Optima Plus Gas Detector, Z ETH ATEX FLOW HSG HART by Honeywell Analytics

Market leading point infrared Hydrocarbon gas detector offering proven performance and sensitivity

With over 40 years experience in the design, manufacture, installation and maintenance of point infrared gas detection, Honeywell Analytics currently has a Worldwide installed base of over 100,000 infrared point Hydrocarbon gas detectors in a wide spectrum of applications from light industrial to the most demanding of offshore petrochemical environments.

Searchpoint Optima Plus is an infrared point Hydrocarbon gas detector certified for use in potentially explosive atmospheres. The unit's infrared detection principle offers the fastest speed of response and fail-to-safe operation, ensuring that your plant is compliant, your personnel are protected and your production process can deliver maximum uptime. Reduced routine maintenance, when compared with conventional electro-catalytic based gas detectors, provides low ongoing cost of ownership. The development of advanced internal fault diagnostics and false alarm rejection algorithms ensures that Searchpoint Optima Plus delivers the highest level of operational integrity.

Typical applications include environments that may suffer from the presence of catalytic bead poisons or inhibitors, or where there are harsh environmental conditions forcing increased time between routine maintenance, for example; offshore oil and gas platforms, floating production storage and offloading (FPSO) vessels, tankers, onshore oil and gas terminals, refineries, LNG / LPG bottling plants, gas compressor / metering stations, gas turbine power plants, refineries, solvent printing and coating plants.

Over 100 gas and vapour calibrations are available. For a list of detectable gases and vapours, please contact our Customer Support team or your local distributor.

Why Infrared?

• Failsafe operation
• Fast speed of response
• Reduced routine maintenance
• Immune to catalytic poisons
• Long operating life
• Works in inert atmospheres

Why Searchpoint Optima Plus is the right choice...

• Experience gained from over 100,000 units installed worldwide
• Improved reliability
• Optional HART® over 4-20mA output
• Can detect a wide range of hydrocarbon gases including solvents
• Increased reliability with no moving parts
• Increased stability from self compensating optics
• Immune to long term component drift
• Remote functional gas test facility
• Certified for North American and European Hazardous areas
• Increased false alarm rejection
• Increased uptime with contaminated optics warning
• Dynamic Heating Control ensures condensation free optics
• No undetected failures
• Improved diagnostics
• Integral event logging
• Reduced power consumption
• Certified to many hazardous area classification schemes including: European (ATEX), UL, CSA, IECEx and more

3615-079 D-ReX PoL Gas Detector with 5 relays and Enclosure, Silane (SiH4) MK477-10, 0 - 50 ppm by GfG

The D-ReX is a very user-friendly, easy-to-maintain gas detector.

High-resolution, full-color display

The 2.4, 320 x 240 pixel full-color TFT display sets new standards for gas detectors. It provides clear and precise information about the current measured values, the short-term and long-term exposure, as well as any malfunctions that may have occurred. Information can be displayed in a variety of languages and scripts, including English, German and Simplified Chinese.

Clear Information

No longer will you have to decipher cryptic error codes – information on any issue is instead displayed in plain text. Status LEDs provide an additional instant overview of vital components of the system.

Intuitive device management using Bluetooth and app

Settings on the D-ReX can easily be managed using the configuration program or the GfG app (Android). They can be connected to the device either via RJ45 an interface or Bluetooth. This will give you access to all settings and configuration options. After entering the password, changes can also be made using the control keys in the D-ReX's service menu.

Advanced connectivity

The D-ReX comes with a wide variety of communication interfaces: Choose between analog, industry standard 4-20 mA, digital RS-485 interface (Modbus/RTU), Ethernet (Modbus/TCP) and LonWorks (optional) for signal transmission. The Bluetooth option enables wireless connectivity. In addition to the five internal, programmable changeover contact relays (optional), 16 additional relays can be addressed by connecting the D-ReX to a GMA200-RT/D relay module.

Periodic sensor self-tests

The plug-and-play smart sensor cartridges are pre-configured and pre-calibrated for easy installation or replacement. Automatic sensor self-tests increase safety while reducing maintenance costs even further.

The new Standard for Versatility: D-ReX

All the advantages mentioned perfectly qualify the D-ReX for numerous applications in virtually all industries. Some of its unique features make it particularly suitable for use in the semiconductor industry, photovoltaic industry and industrial manufacturing as well as in laboratories. If you are looking for the gas detector that best suits your needs, the D-ReX will be your first choice for many applications.

Possible areas of application:

• MRI Labs
• Process tools
• Vacuum pumps
• Scrubbers
• Gas cabinets
• Ambient breathing zones
• Storage areas
• Cleanroom environments
• Sub fab systems

Features:

• Sensors for more than 30 gases
• Hot-swappable smart sensor cartridge
• High-resolution, full-color 2.4" TFT display
• Plain text information
• Tool-free maintenance
• Power-over-Ethernet (PoE) communication
• Can be addresses via web portal
• Password-protected menu
• Interface: Analog: 4 20 mA output; Digital: RS-485 (Modbus/RTU); 10/100 Mbit Ethernet (Modbus/TCP)
• Bright status and alarm LEDs
• Data logger to review sensor and alarms history
• CE marked and UL certified

USPs:

• Tube length up to 30 m / 100 ft.
• Extension cable 1 m / 30 m
• Easy to replace mechanical component of internal pump
• Bluetooth®

Options:

• 16x external relays (GMA200-RT/D)
• Line Integrity Monitoring

GS-BG-A-074-G Gasman Single Gas Monitor, 0-500ppm Hydrogen Sulphide, Rechargable Battery, Polish Safe Area only by Crowcon

For over 40 years, Crowcon Detection Instruments has produced state of the art gas detection devices for personal and industrial use. Building upon their reputation for reliable and innovative gas monitoring products, Crowcon introduces the Gasman personal gas monitor. Its lightweight and compact design is convenient for jobsites where workers need not be weighed down by excessive bulk and equipment. The unit conveniently clips to a pocket or helmet and operates continuously.

The Gasman personal gas monitor has numerous convenient features such as:

• One button technology
• Backlit LCD display
• Durable polycarbonate casing
• Quick response triple alert system
• Compact and lightweight design

Easy to Use

The Gasman s true one button technology is an ideal and simple design. The large glove friendly button is mounted on the front of the unit for easy access and controls all of the unit s programmable features. Also on the front, the Gasman s easy to read backlit LCD screen indicates gas readings and the battery status. The simple screen provides a clear indication of the unit s operation status. It will also alert the user 30 days in advance of when a calibration test is due. With a simple and intuitive design, Crowcon has produced a gas detector that reduces the complexities of workplace safety, and ensures workers in a straightforward manner that their equipment is on and operational.

Triple Alarm System

This portable single gas detection system features a triple alarm system that is sure to alert the user and anyone in the vicinity. The visible alarm utilizes a dual red and blue flashing LED light, and the unit houses an internal vibrating alert system. These two indicators allow for visual recognition in loud environments and working conditions. The alarm system also features a programmable audible alarm at 95 decibels. The unit is capable of a variety of alarm tones, and users can select which tone may be best for the individual workplace setting. The triple alarm system with multiple sensory indicators is sure to be noticed in almost any work environment.

Specifications

The Gasman single gas monitor is lightweight and compact, weighing less than 135 grams and with dimensions of 90 x 48 x 24 mm. The unit is available with a wide variety of gas sensors which feature various detection and alarm levels. The unit also features a quick response time of 20 seconds for flammable and toxic gases or 10 seconds for oxygen. Its datalogging feature has approximately 900 hours of storage and all events are time stamped. The battery life for this unit is incredible with 12 hours of runtime on a Rechargeable battery battery or up to 2 years on a non-Rechargeable battery.