All Products

WD-27502-05 Cole-Parmer® Ion-Selective Electrode (ISE), Bromide, Double-Junction, BNC by Oakton

Whether your application involves end point determinations in potentiometric titrations or continuous monitoring of specific ions, we can help you find the right electrode for the job. These fast and accurate electrodes do not require an external reference - they're easier to use than separate sensing and reference half-cell electrodes. All Cole-Parmer electrodes are double-junction combination ion-selective electrodes and are convenient to use in places where two electrodes won't fit. All electrodes include a 30-mL bottle of reference solution, a reference filling pipette, 1-m cable, BNC connector, and an instruction manual. Solid-state electrodes also have twelve polishing strips.

Economy Epoxy Electrodes have a durable epoxy body and are well-suited for portable field applications. Outer reference chamber is silver-free and resists contamination. These electrodes are refillable.

Laboratory Glass Electrodes are double-junction in design, with a glass body that provides high-quality measurements for your laboratory applications. Improved glass seal enhances performance and reliability. Sealed inner junctions and refillable outer junctions accommodate special reference fill solutions - ideal for low-concentration measurements. Use electrodes with a meter that has a resolution of 0.1 mV for the most accurate results. Many meters in our "pH/Ion Meters" section have 0.1 mV resolution; several also give direct readings in ppm. For monitoring ions not listed below, call our Application Specialists for more electrode application information.

• Cost-effective choices that are easy to use
• Easily fit into small spaces - no additional reference electrode is needed
• Bromide (Br^-) ISE with glass body

TDSNA1/G Conductivity Solution, 1000ppm/497.7uS, 1 Gal. by Sensorex

TDS/Conductivity instruments and sensors must be calibrated together. For a single-point calibration, select the one solution that approximates the expected conductivity or ppm level of total salts. Mixed Salt standards are the most frequently used in the field to sample naturally occurring water sources, boiler feed water, or cooling tower water. Typical river water, well water, or lake water sample will contain a mixture of several different salts. Sensorex Mixed Salt standards simulate a "Natural" mixture of common salt compounds found in these sources. Sodium sulfate, sodium bicarbonate, and sodium chloride salts are blended to provide a representative value. There are certain applications where Single Salt Solutions are preferred. NaCl Solution is routinely used to calibrate instruments measuring Sea Water or brackish water samples. Reagent grade salt and high resistivity DI water is compounded for accurate results. KCI Single Salt Solution may be used with conductivity meters that read directly in Siemens or Ohms. KCI (potassium chloride) is established as an international calibration standard for conductivity measurement. Choose the conductivity calibration solution that is right for your application. CA Residents: Prop 65 WARNING(S)

Part Number: H19711.62VM1

3300-43-001 CC 33 Fixed Transmitter with Hydrogen (H2), Aluminum Housing, 0-100% LEL (MK 217-3), 4-20 mA No Relay by GfG

It has always been our aspiration to combine innovative ideas and technology with functional design. This is how quality and longevity come about. Attributes symbolic of the name GfG in gas measurement.

Are you looking for an innovative transmitter for flammable gases, but need explosion protection? Then a transmitter from the GfG 33 series is the right choice.

Robust housing for every application

The transmitters of the 33 series are flameproof encapsulated and fulfill the requirements of the type of protection "d". Depending on the application, you can choose the 33 transmitter with an epoxy-based aluminum or a pure stainless steel housing. In order to meet the quality requirements of our customers and our own standards in terms of durability, we use a particularly high-quality and durable Viton seal in the 33 series. This can withstand even the toughest operating conditions for many years.

Variants

GfG offers the CC 33 in two variants:

For conventional industrial The CC 33 is available in a lacquered die-cast aluminum housing with 10mm thick bulletproof glass. Applications with special conditions such as e.g. in the Food industry can be covered by a unpainted housing made of stainless steel with a 15mm thick bulletproof glass.

Operation by means of magnetic pin

The three magnetic switches behind the protective glass, which is up to 15mm thick, can be operated using the GfG magnetic pin. The GfG typical three-button operation is easy to understand. The menu is clearly structured and logically structured.

All transmitters of the 22, 29 and 33 series have a uniform user interface. The uniform operation and the logical system structure keep your training and maintenance effort as low as possible.

Proven and innovative is not a contradiction

The CC 33 works on the principle of catalytic heat generation (WT), a proven method for measuring combustible gases. The transmitters are equipped with high-performance electronics for voltage stabilization, processing of measured value output and temperature compensation. The long life of the sensors minimizes follow-up costs.

Sensor technology

With improved sensor technology and the unique GfG "chimney effect", the CC 33 transmitter for combustible gases has one of the fastest response times in the world. There are more crucial seconds left to initiate countermeasures and to bring people to safety.

Universal signal transmission

The measured values and status displays of the 33 series can be transmitted either analog or digital via the Modbus interface. Due to the different variants of signal transmission, a transmitter of the 33 series can be connected to almost any gas warning system as an additional measuring point or in exchange for existing transducers.

Signal processing

The embedded software of the 33 transmitter linearises the measurement signal and compensates for temperature influences. As a result, correct measured values are transmitted even in the event of weather-related temperature fluctuations. The execution of the software enables the detection of faults and, in the Modbus variant, the requirement of required service or maintenance work.

Smart sensors

Pre-calibrated sensor modules can be screwed directly into the sensor receptacle on the housing of the CC 33. The smart GfG sensors are pre-programmed with all the necessary parameters and can be used without much effort ("plug and play"). Sensor changes are shown in the display. (catalytic and electrochemical sensors)

Three freely programmable internal relays

The 33er transmitters can be used as a "stand-alone system". You can set the two alarm thresholds individually and freely program the optional three relays. You do not need a cable to a controller and you can nevertheless reliably switch safety-related devices.

With colored graphic display

The clearly laid-out graphic display makes it easy to read the device status, the current measured value and many other important information. In the event of an alarm, the display turns red. The large LEDs signal from a distance the current device status and thus serve the rapid information of your employees about any alarms or malfunctions.

Using the display, you can easily navigate through the clear device menu and make various settings, including calibration, depending on your user authorization.

Calibration

For regular function control with gas application, a calibration adapter is placed on the transmitter to ensure a safe and even gas supply.

Part Number: 10L-321

0632 0313 312 Auto-ranging Digital Manometer (+/- 16" H2O & +/- 80" H2O) by Testo

testo 312-2, DVGW approval according to TRGI, measures pressure from 0 to 200 hPa. Even the finest of pressures with a resolution of 0.01 mbar can be measured in the measuring range from 0 to 40 mbar.

• Clear display with time
• Switchable precision range with a high resolution
• With alarm function
• Printout of data incl. software, instrument number, date/time on Testo printer
• Quick data printout on location
• DVGW approval

Part Number: 17L-334

72-6XPD-B GX-6000 Sample Draw Gas Monitor, Cl2/IR HC, with alkaline batt pack/Li-Ion batt pack/100-240 VAC chgr by RKI Instruments

Simply put, the GX-6000 is a game changer. This powerful hand-held instrument is capable of simultaneously monitoring up to 6 gases. In addition to the standard 4 confined space gases which include combustibles, O2, CO, & H2S, the GX-6000 has 2 additional smart channels that accept PID, IR or super toxic sensors. Equipped with a strong internal sample pump, a man-down alarm, a panic alarm, an LED flashlight, and large auto rotating LCD display, the GX-6000 can operate as a single gas PID unit or a multifunctional tool utilizing all 6 channels. The GX-6000 with a PID sensor will come equipped with a library of over 600 VOC gases to choose from as standard. Choosing from the library is easy with a personalized favorites list of 30 commonly used VOC's as well as a list of 8 of the most recently used VOC's.

The GX-6000 has a rugged design built for the nastiest environments. It is equipped with a removable impact-resistant rubber boot and a dust and water resistant enclosure with an IP-67 rating. With 5 bright LED lights on 3 sides of the instrument, alarms are easily seen from a variety of perspectives. With vibration and loud audible alarm, GX-6000 will easily alert users when needed.

Features

• Monitor up to 6 gases
• 2 smart sensor slots auto recognize PID, IR, and super toxic sensors
• 5 Operating modes: normal, leak check, inert, snap log and bar hole
• Library of over 600 VOCs
• PPM Leak Check mode
• Man-down and panic alarms
• Auto display rotation
• LED Light source
• Internal sample pump
• Glove friendly glow in the dark buttons
• Light weight, small, rugged IP-67 design
• Interchangeable battery packs Li-ion / alkaline
• Operates up to 14 hours on Li-ion battery pack, fully recharges in 3 hours
• Field replaceable sensors, batteries and filters

Applications

• Confined space entry
• Hazmat response teams
• Arson investigation
• Remediation sites
• Perimeter monitoring
• Leak detection
• Landfill monitoring
• Wing tank entry

*Please note we can only ship RKI products to customers within the United States

SSRE-C-MB/EN/2000 Smart Remote Electronics, Toroidal Conductivity, Modbus 485 output, UL Enclosure, 0-2000 mS Range by Sensorex

Thank you for choosing Sensorex Smart Sensor Remote Electronics. This instruction manual covers all remote electronics modules for PH, ORP, DO, contact conductivity(CCOND), toroidal conductivity(TOR), free chlorine(FCL) and chlorine dioxide(CLD) sensors. The remote electonics modules are offered in DIN Rail and blind enclosure version. Output for the modules (either Modbus RTU or 4-20mA) is marked on the product label.

Convert Analog Sensors into Smart Sensors

• Reduce inventory by stocking analog sensors and wire them to remote electronics to output a digital communication signal (4-20 mA or Modbus)
• Save on costs by only replacing the sensor; keep remote electronics and cabling in place
• Improve environmental impact by eliminating electronics waste after sensor end of life

Compatible with a Comprehensive Set of Measurements

• pH/ORP, Contacting Conductivity, Toroidal Conductivity, Dissolved Oxygen, Free Chlorine, and Chlorine Dioxide
• Simple wiring for each measurement type

Two Versions for Your Ideal Application

• Interface module for DIN Rail installation
• Enclosure box for wall or panel mounting

VP5-02201001111 Ventis Pro5 Personal Gas Monitor, H2S (DualSense), Li-ion Battery, No Pump, Orange, UL/CSA, LENS Wireless, English by Industrial Scientific

Detect up to five gases simultaneously with the rugged, wireless, Ventis® Pro5 Multi-Gas Monitor. With Ventis Pro5, safety goes beyond the gas detector whether you need team-based alarm sharing, remote monitoring with location details, or both. The monitor is also backed by a Guaranteed for Life™ warranty.

• Eliminate the need for two pieces of equipment by using Ventis Pro5 for personal monitoring and confined space entry.
• Train workers on one, multi-purpose gas monitor and reduce the risk and investment of having different devices in the field.
• Improve team and site safety by locally sharing alarms and gas readings between wirelessly connected Ventis Pro5 monitors.
• Get real-time location and alarm data directly from Ventis Pro5 gas monitors to a designated safety contact with the optional cellular or wi-fi battery pack.
• Reinforce safe behavior with programmable alarm action messages like "EVACUATE" or "VENTILATE" based on alarm level.
• Simplify the user experience with the ability to hide unnecessary screens based on user needs, role, industry, or site.

726-017-ID Eagle 2 Portable Monitor, LEL(CAT)/Oxy/H2S/CO/NH3/SO2, with internal LEL CAT dilution by RKI Instruments

Continuing in its legacy of durable and reliable gas detection and monitoring systems, RKI Instruments is proud to offer a new product in its popular Eagle portable gas detector series. The Eagle 2 can monitor up to 6 different gases and is equipped with several exclusive features that can only be found with the Eagle series. In addition, its large glove friendly push buttons and LCD screen ensure an ease of use when onsite. Rated intrinsically safe, the Eagle 2 is equipped with state of the art technologies that are not available with other competitive gas detectors and monitors.

Specialty Sensors

The Eagle 2 has a variety of available specialty sensors. Workers can use a photoionization detector for low or high range VOC detection and Fence Electrode Technology for humidity and contamination resistance. An infrared sensor is available for Co2, % LEL CH4, % Volume CH4, % LEL HC, and % Volume HC. Thermal conductivity sensors are available for % Volume H2 and % Volume CH4. The unit is also compatible with the smart plug and play toxic sensors for the detection of NH3, AsH3, CI2, HCN, PH3, and SO2. With the wide variety of sensors and gas detection available, the Eagle 2 can be customized to meet almost all worksite gas detection needs.

Exclusive Features

The monitor has a long internal pump that can draw samples for up to 125 feet. The pump features a low flow auto shut off and alarm. This allows operators to respond swiftly from a safe distance. The unit is multilingual with 5 different language preferences, and features an alkaline battery life of 18 hours or a NiMH life of 20 hours. To protect the integrity of the device and the configurations, the unit can be password protected. The Eagle 2 also has standard data logging capabilities for easy research, evaluation, and site monitoring. To reduce calibration costs and time, the unit features an automatic calibration option and a single gas calibration option.

The Eagle 2 is heavily protected from environmental conditions by a weather proof, chemical resistant RFI/EMI coated high impact polycarbonate/PBT blend enclosure. The enclosure also renders the unit water and dust resistant. Because of the enclosure, the Eagle 2 can function in 2 inches of water without leakage.

Eagle 2 Specifications

The portable and durable unit is lightweight at less than 4 pounds. Its dimensions are suitable for convenient carrying (9.5 L x 5.25 W x 5.875 H), and it features a conveniently placed durable top handle. The large easy to read display has a polyurethane overlay backlights on demand and when the alarm is activated. The 2 alarm channels are fully adjustable for the user and can be password protected. With a 95 dB buzzer and 4 high intensity LEDs, the alarm is sure not to be missed. The Eagle 2 is standard with a 2 year warranty for material and workmanship and a 1 year warranty for PID sensor.

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

Part Number: E107850LM5

3622-152 D-ReX PoS Gas Detector with 5 relays, Propane (C3H8) MK221-10, 0 - 100 % LEL (CC) by GfG

Not all gases can be monitored directly at the measuring point. This may be because the maintenance of a remote sensor would be too complicated or because the target gas has to be broken down into detectable components first. This can be done using a pyrolyzer.

In these cases, the D-ReX PoS with its integrated pump is an ideal solution. The point of sampling (PoS) can be up to 100 feet / 30 meters away from the D-ReX. This also applies to the length of the recirculation hose.

Available Accessory:

• DIN rail
• PTFE hose
• Various particle filters
• Push-Pull plug-in adapter
• Angle braces

Features:

• 5x internal relays (form C, configurable)
• Smart sensors for more than 60 gases
• Hot-swappable smart sensor cartridge
• Tool-free maintenance
• Power-over-Ethernet (PoE) communication
• Web server for browser access
• Password-protected menu
• Interface: Analog outlet: 4 20 mA output; Digital: RS-485 (Modbus/RTU); 10/100 Mbit Ethernet (Modbus/TCP)
• Bright status and alarm LEDs
• Data logger to review sensor and alarm history
• Marked as FCC, CE, IC and UKCA

3600S75 "No-Air" 12V 20W Aluminum Body Abrasive Blast Light System with Power Pack & 75' Electric Cable by Western Technology

The 3600 HALOGEN NO-AIR ALUMINUM BLAST LIGHT is the best solution for all of your blasting needs. With a built in Light Stanchion, aluminum body and additional options available, it is a must have tool for your lighting needs.

Features

• 12 volt repairable blast light made specifically for abrasive blasting
• Aluminum body
• 20 Watt halogen bulb
• Built in Light Stanchion
• Additional options available

GHS1060 Exclamation Mark Pictogram Tag (25/pk) by GHS Safety

HazCom GHS Pictogram Tags offer a quick and easy way to identify hazards throughout your facilites. Perfect for marking drums, valves, cylinders and many other applications. Each durable plastic tag has the HazCom GHS pictogram and written description both sides, so the hazard information is always visible. Available in English/Spanish or English/French versions. 25 tags per pack. EN/FR