Sulfur Dioxide Calibration Gas

2811-731-001M EC 28 Gas Transmitter with MODBUS, Sulfur Dioxide (SO2), No Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

65-2340RK-SO2 S2 Series Sulfur Dioxide (SO2) 0 - 6 ppm Sensor/Transmitter, Non Explosion Proof with J-Box by RKI Instruments

Having a reliable gas sensor is detrimental to the safety and security of workers in potentially unstable work environments. In many cases, the decision to use a gas detection device with a reliable sensor can be the difference between life and death. RKI Instruments understands the reliability of gas sensors should be a top priority for workplace safety managers. Their team of experts works diligently to incorporate the most advanced technologies with the highest industry standards.

For nearly 20 years, RKI Instruments has worked in the gas detection industry. Its line of products leads the industry in innovation and technology. Every year, the company commits to achieving a higher level of productivity and delivering the best gas detection products on the market. With the introduction of their high performing, low cost S2 Sensor Transmitter, RKI is fulfilling that commitment.

S2 Sensor/Transmitter

The RKI S2 Sensors and Transmitters use state of the art sensor technology to detect common gas hazards. Their efficient design and cost effectiveness make them an industry choice for atmospheric monitoring. The sensor transmitters can be used in both indoor and outdoor conditions and are designed to interface with RKI controllers or PLC/DCS systems.

The sensors are available in explosion proof casing for monitoring LEL, H2 specific, oxygen, H2S, CO2, and carbon monoxide. These sensors also have flame arrestors and are approved for use in hazardous environments. The oxygen, H2S, CO, and CO2 sensors are available in non-explosion proof models. The sensors provide highly specific and quick detection and are long lasting. The sensors can be quickly replaced while on the field and do not require any tools.

Explosion proof S2 Sensor/Transmitter

The explosion proof sensors use a variety of detection mechanisms including catalytic for LEL and LEL- H2 specific; metal oxide semiconductor for hydrogen; galvanic cell technology for oxygen; electrochemical for hydrogen sulfide and carbon monoxide; and infrared for carbon dioxide, methane, and hydrocarbons. A hydrogen specific sensor transmitter is not available. Each of these detection methods come with their own measuring range specifications and response times varying from 20 seconds to 45 seconds. These sensors are stainless steel and are housed in a cast aluminum explosion proof J-Box (a stainless steel J-Box is also available).

Non-explosion proof S2 Sensor/Transmitter

The non-explosion proof sensors use galvanic cells for oxygen detection; electrochemical technology for hydrogen sulfide, carbon monoxide, and other toxics; and infrared technology for carbon dioxide detection. The response times vary between 20 seconds and 60 seconds depending on the targeted gas, and the measuring ranges vary as well. These sensors are plastic or aluminum and housed in an explosion proof J-Box.

Accessories

The S2 Sensor/Transmitter has numerous accessories available to meet the individual workplace's needs. Such accessories include calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors or panels, and data loggers.

Each sensor comes standard with a one year warranty for materials and workmanship.

*Please note we can only ship RKI products to customers within the United States

500-10 Handheld Combustion Efficiency Emissions Analyzer includes O2, CO, NO, NO2, NOx, SO2 (Sulfur Dioxide), Temperature, Draft, Combustibles, Printer, Blue-Tooth, Thermoelectric Condenser/Peltier Cooler by Enerac

Enerac invented the first electronic portable multi-parameter combustion analyzer in 1979 (in the USA). Enerac still services this analyzer as well as all others Enerac has manufactured. The Enerac Model 500 is a low-cost, easy to use (no technical expertise needed) portable combustion efficiency emissions analyzer. The Enerac 500 is perfect for determining the efficiency of a combustion source as well as for collecting advanced emissions data for internal use, or for local, state and federal emissions reporting requirements.

The Enerac 500 is perfect for testing various combustion sources, such as boilers, burners, engines, turbines, generators, kilns, dryers, heaters and ovens (just to name a few). Equally, with a simple combustion efficiency test, or a more advanced combustion emissions test, the Enerac 500 is designed to provide years of trouble-free service. It is flexible enough to be tailored to meet your specific needs, yet simple enough to be completely maintained in the field. Advanced design, rugged construction and an impressive array of options are its hallmark. Constructed as a field work-horse the Enerac 500 can be upgraded (adding sensors and options to the same unit) to meet your changing needs at any time.

Introduction

The Enerac 500 provides a comprehensive range of automatic emissions calculations, advanced Enercom Windows Software, two-way communications and factory support. From low NOx burners, (0.1ppm NOxresolution) to large rich burn engines (5,000ppm (NOx)/20,000ppm CO) the Enerac 500 is designed to help meet your needs of various monitoring applications at an affordable price.

The Enerac 500 handheld combustion efficiency emissions analyzer, is our newest, low cost, Emissions-Monitoring System, utilizing standard electrochemical sensors. It is designed to help you meet the challenges of a rapidly changing regulatory environment. It is easy to use, comprehensive (O2-CO-NO-NO2-(NOx), SO2, Combustibles, Stack Temperature, Draft), and flexible.

• A micro-sized Combustion-Efficiency analyzer and Emissions-Monitoring System
• Thermoelectric Condenser / Peltier Cooler (sample conditioning system for proper detection and measurement of NO2 and/or SO2 gasses
• Powered by 4xAA Rechargeable batteries
• Built-in Thermal Printer: 2" Character-type
• Our Enercom Windows Software included
• USB and Serial Ports included. Bluetooth Wireless (optional)

Rugged

The Enerac 500 is designed for years of trouble-free service. Housed in a rugged, lightweight aluminum case, its modular design allows end-users the ability to replace a battery or sensor, in a matter of seconds. Reducing both downtime and costs.

• Rugged lightweight aluminum case
• Work-horse of the industry
• Won't warp or crack like plastic models
• Small, lightweight and tough
• 2 Year Warranty
• 24 Hour Service
• Best service and support in the industry

Comprehensive

The Enerac 500 provides an extensive range of data management, and support options. It not only (automatically) performs complicated emission calculations, it can even allow the user the ability to identify specific data sets with a specific customer, dramatically reducing retrieval and processing costs.

Enerac 500 is compatible with Enerac's advanced Enercom for Windows ™ software. All parameters can be continuously displayed; Minimum, Maximum, Averages and Standard Deviations calculated; Multiple plots and graphs can be viewed or printed. With the Enercom software, data management and report writing is now a snap. With the Enerac 500, help is never more than a phone call or email away.

Affordable

With all these capabilities the Enerac 500 is surprisingly affordable.

• Buy only what you need and add options later
• Always upgradeable (anytime)!
• Free software and accessories
• Receive a generous trade-in allowance on your old analyzer
• Loaners available at no charge.

Compliance Level

The Enerac 500 can be configured to a compliance-level analyzer with addition of several key features. The Enerac 500 has the ability to produce Total NOx data for one. With both the NO and NO2 sensors Total NOxis obtained (NOx)=NO+NO2 on stationary combustion sources). The ability to also configure the 500 with High Sensativity sensors allows extreme accuracy over the sensors shorter range etc. Additionally, the 500 has the option to have the Thermoelectric Condenser (also called Peltier Cooler) option installed. This is a sample conditioning system (usually found on our competitors larger more expensive units) essential for proper NO2 and or SO2 gas detection and measurement. With the final addition of the viton hose, sample quality is maintained and compliance level data obtained. Therefore, the Enerac 500 is perfect for meeting your local, state and federal regulatory emissions compliance requirements.

• Free data collection software
• Time-stamped internal data storage
• Total NOx (NO and NO2)
• High Sensitivity / Low Range Sensors Available
• Viton and Teflon hose options
• Sample Conditioning System (for proper NO2 and/or SO2 gas detection and measurement)
• Field replaceable sensors
• Easy field calibrations (if desired)
• Comply with local, state and federal emissions requirements

In a world of downsizing, and increasing workloads, the Enerac 500 can help you simplify your job. With a broad array of available options, the Enerac 500 will provide you with the capabilities you need, when you need them, all within your budget.

3507-050 EC 35 Fixed Gas Transmitter, Sulfur Dioxide (SO2), Display by GfG

Remote Transmitters for Oxygen and Toxic Gases

The EC 30 is an advanced transmitter for the detection of toxic gases and oxygen levels. This smart area monitor has an aluminum explosion proof housing with a stainless steel sensor cover that makes the EC 30 series suitable for the harshest environments.

Simple and effective

Once you power up the units, they will accurately display values on the large LCD and transmit a linear 4-20 mA signal to any GfG controller. AutoCal automatic calibration and maintenance is done effortlessly through push buttons or via a digital remote control connection. Smart sensors allow the user to easily change ranges or gas types in the field without a need for additional programming. The EC 36 is equipped with onboard relays for two alarm points and one sensor fault for local connection and activation or deactivation of external devices like alarms, fans, auto dialers etc.

Digital display / control connection

The digital connection allows display of readings, non-intrusive maintenance and AutoCal calibration activation to be done locally or from a distance.

Features

• Robust industrial design
• Fully-automatic one button calibration adjustment

Part Number: 116L-174-10

BW Clip 2 Year Single Gas Detector, Sulfur Dioxide (SO2), Low - 5 ppm / High - 10 ppm, Black Housing by BW Technologies

The BW Clip single-gas detector is your everyday companion for hazardous environments. It operates up to three years maintenance-free: Just turn on the device and it runs continuously - no need for calibration, sensor replacement, battery replacement or battery charging. That means great reliability and no downtime.

Plus, with the two-year BW Clip for H2S or CO, you can put the device in a hibernation case when you re not using it for a week or more - and extend its life by that period of time.

Compatible with both the MicroDock II and the IntelliDoX instrument management systems, the BW Clip is engineered to the highest standards of quality and reliability, keeping you safe and compliant.

Use our unique advanced technology for safety, compliance and productivity.

Surecell™: unique dual reservoir sensor design dramatically improves instrument performance, response time, and longevity compared to traditional electrochemical sensors and consistently delivers reliable instrument performance under the harshest environmental conditions

Reflex Technology™: advanced automated self-test function routinely checks the operating condition of the sensor to increase safety, up-time, and overall worker confidence

IntelliDoX: instrument management system

• The quickest bump test in the industry
• Confi guration of alarm set points and more
• Performing different tests for up to five BW Clip detectors at once - for maximum productivity
• Easy and accurate record-keeping

BW Clip Standard Features:

• Maintenance-free: no sensor or battery changes necessary
• Compact, lightweight design with one-button operation
• Designed for a range of harsh environments and extreme temperatures
• Hibernation mode with case accessory or IntelliDoX
• Automated self-test of battery, sensor and electronics
• Wide-angle flash, which alerts simultaneously with audible and vibrating alarm
• Automatic logging of the 35 most recent gas events and bump test results
• Compatible with MicroDock II and Fleet Manager II software
• Affordable, with low cost of ownership

Configureable Options:

• Configuration of high and low alarm set points before the device is activated
• Adjustment of alarm set points and other parameters as needed throughout the lifespan
• Option to enable the noncompliance indicator, which flashes red when a bump test is due or a gas event occurs
• Option to display gas reading during alarm
• User settable bump test reminder
• Option to display the Real Time Clock

Part Number: BWC2-S-B

Part Number: Z10795PM2

Part Number: 116L-175-25

Part Number: Z107910PM4

Part Number: U107950PA

73-0051RK-SO2 SC-01 Single Toxic Gas Monitor, Sulfur Dioxide (SO2), 0 - 6.00 PPM, with Belt Clip by RKI Instruments

Paving the way for gas detection and monitoring solutions, RKI Instruments produces the most advanced sensors and monitors. Their teams of experts are constantly seeking new and innovative methods for meeting the unique needs of jobsites with potentially hazardous conditions. Integrating the latest smart sensor technology with functional design, RKI Instruments is proud to present the SC-01 Model for single toxic gas monitoring.

SC-01 Model Single Toxic Gas Monitor

The SC-01 Single Toxic Gas Monitor is the latest in smart sensor technology with practical applications in refineries, chemical plants, hazmat response, semiconductor plants, and more. It is a versatile single gas detector with interchangeable sensors. The unit automatically recognizes when a sensor has been changed and automatically calibrates to the recognized sensor. The internal technology stores each sensor's configuration and activates the data once the new sensor is recognized.

What sets the SC-01 apart from its competitors is its wide range of available ESM-01 sensors including unique sensors for arsine, ammonia, carbon monoxide, chlorine, hydrogen cyanide, hydrogen sulfide, phosphine, and sulfur dioxide. These plug in style sensors are easy to change and can be replaced quickly while onsite. Onsite workers can also utilize the optional 10 foot extender cable for remote monitoring and quick response.

Exclusive Features

The SC-01's large backlit LCD display is great for onsite use and is easy to read. The screen displays the gas reading, battery level, and current time. When the alarm is activated, the LCD screen's backlight automatically activates. The alarm features a quadruple notification system that includes a buzzing audible alarm, a blinking LED display, a vibration alert, and display indicator. The unit performs regular safety self-evaluations for sensor connections, battery life, and circuit issues. Amazingly, the unit can function with more than 250 hours of continuous operation with 2 AA alkaline batteries. The SC-01 comes standard with data logging capabilities ensuring that workplace safety managers are able to monitor, record, and evaluate possible hazard trends.

SC-01 Model Specifications

The unit is highly portable with its lightweight (less than 8 ounces) and pocket size dimensions (2.6 x 6.2 x 1.2 ). Users can easily control the unit's functioning with its 3 large front facing push buttons. The casing is designed to protect the monitor with its high impact plastic with rubber boot that is dust proof and splash proof. The typical response time for gas detection is approximately 60 seconds and uses electrochemical detection. For gas monitoring needs, the SC-01 Model is rated intrinsically safe.

The SC-01 Single Toxic Gas Monitor comes standard with several accessories for easy use including an alligator clip, AA alkaline batteries, impact resistant rubber boot, and a user manual. Users can also purchase optional accessories to further customize the unit to meet specific workplace needs. These optional accessories include a belt clip, a 10 foot extender cable, and datalogging software that is PC compatible.

*Please note we can only ship RKI products to customers within the United States

2811-731-003M EC 28 Gas Transmitter with MODBUS, Sulfur Dioxide (SO2), Display / Alarm by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

Old Part Number: Z107935
New Part Number: Z107935PN

Part Number: U107925PM1

2811-731-002 EC 28 Gas Transmitter with Sensor, Sulfur Dioxide (SO2), Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

2811-731-002M EC 28 Gas Transmitter with MODBUS, Sulfur Dioxide (SO2), Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

500-1 Handheld Combustion Efficiency Emissions Analyzer includes SO2 (Sulfur Dioxide) Sensor by Enerac

Enerac invented the first electronic portable multi-parameter combustion analyzer in 1979 (in the USA). Enerac still services this analyzer as well as all others Enerac has manufactured. The Enerac Model 500 is a low-cost, easy to use (no technical expertise needed) portable combustion efficiency emissions analyzer. The Enerac 500 is perfect for determining the efficiency of a combustion source as well as for collecting advanced emissions data for internal use, or for local, state and federal emissions reporting requirements.

The Enerac 500 is perfect for testing various combustion sources, such as boilers, burners, engines, turbines, generators, kilns, dryers, heaters and ovens (just to name a few). Equally, with a simple combustion efficiency test, or a more advanced combustion emissions test, the Enerac 500 is designed to provide years of trouble-free service. It is flexible enough to be tailored to meet your specific needs, yet simple enough to be completely maintained in the field. Advanced design, rugged construction and an impressive array of options are its hallmark. Constructed as a field work-horse the Enerac 500 can be upgraded (adding sensors and options to the same unit) to meet your changing needs at any time.

Introduction

The Enerac 500 provides a comprehensive range of automatic emissions calculations, advanced Enercom Windows Software, two-way communications and factory support. From low NOx burners, (0.1ppm NOxresolution) to large rich burn engines (5,000ppm (NOx)/20,000ppm CO) the Enerac 500 is designed to help meet your needs of various monitoring applications at an affordable price.

The Enerac 500 handheld combustion efficiency emissions analyzer, is our newest, low cost, Emissions-Monitoring System, utilizing standard electrochemical sensors. It is designed to help you meet the challenges of a rapidly changing regulatory environment. It is easy to use, comprehensive (O2-CO-NO-NO2-(NOx), SO2, Combustibles, Stack Temperature, Draft), and flexible.

• A micro-sized Combustion-Efficiency analyzer and Emissions-Monitoring System
• Thermoelectric Condenser / Peltier Cooler (sample conditioning system for proper detection and measurement of NO2 and/or SO2 gasses
• Powered by 4xAA Rechargeable batteries
• Built-in Thermal Printer: 2" Character-type
• Our Enercom Windows Software included
• USB and Serial Ports included. Bluetooth Wireless (optional)

Rugged

The Enerac 500 is designed for years of trouble-free service. Housed in a rugged, lightweight aluminum case, its modular design allows end-users the ability to replace a battery or sensor, in a matter of seconds. Reducing both downtime and costs.

• Rugged lightweight aluminum case
• Work-horse of the industry
• Won't warp or crack like plastic models
• Small, lightweight and tough
• 2 Year Warranty
• 24 Hour Service
• Best service and support in the industry

Comprehensive

The Enerac 500 provides an extensive range of data management, and support options. It not only (automatically) performs complicated emission calculations, it can even allow the user the ability to identify specific data sets with a specific customer, dramatically reducing retrieval and processing costs.

Enerac 500 is compatible with Enerac's advanced Enercom for Windows ™ software. All parameters can be continuously displayed; Minimum, Maximum, Averages and Standard Deviations calculated; Multiple plots and graphs can be viewed or printed. With the Enercom software, data management and report writing is now a snap. With the Enerac 500, help is never more than a phone call or email away.

Affordable

With all these capabilities the Enerac 500 is surprisingly affordable.

• Buy only what you need and add options later
• Always upgradeable (anytime)!
• Free software and accessories
• Receive a generous trade-in allowance on your old analyzer
• Loaners available at no charge.

Compliance Level

The Enerac 500 can be configured to a compliance-level analyzer with addition of several key features. The Enerac 500 has the ability to produce Total NOx data for one. With both the NO and NO2 sensors Total NOxis obtained (NOx)=NO+NO2 on stationary combustion sources). The ability to also configure the 500 with High Sensativity sensors allows extreme accuracy over the sensors shorter range etc. Additionally, the 500 has the option to have the Thermoelectric Condenser (also called Peltier Cooler) option installed. This is a sample conditioning system (usually found on our competitors larger more expensive units) essential for proper NO2 and or SO2 gas detection and measurement. With the final addition of the viton hose, sample quality is maintained and compliance level data obtained. Therefore, the Enerac 500 is perfect for meeting your local, state and federal regulatory emissions compliance requirements.

• Free data collection software
• Time-stamped internal data storage
• Total NOx (NO and NO2)
• High Sensitivity / Low Range Sensors Available
• Viton and Teflon hose options
• Sample Conditioning System (for proper NO2 and/or SO2 gas detection and measurement)
• Field replaceable sensors
• Easy field calibrations (if desired)
• Comply with local, state and federal emissions requirements

In a world of downsizing, and increasing workloads, the Enerac 500 can help you simplify your job. With a broad array of available options, the Enerac 500 will provide you with the capabilities you need, when you need them, all within your budget.

2811-731-003 EC 28 Gas Transmitter with Sensor, Sulfur Dioxide (SO2), Display / Alarm by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

65-2618RK-SO2 M2, Sulfur Dioxide (SO2) 0 - 6 ppm Sensor/Transmitter, Non Explosion Proof with J-Box by RKI Instruments

RKI Instruments uses the latest cutting edge technology when developing transmitters and sensors. Its dedication to workplace safety and reliable safety solutions is unparalleled. The M2 Stand Alone Transmitter utilizes state of the art sensor cell technology to integrate workplace safety with the industry's more advanced transmitter technologies.

M2 Stand Alone Transmitter

The M2 Stand Alone Transmitter is operational with or without a controller and is available in two forms: explosion proof and non-explosion proof. The unit has a backlit screen for a direct digital readout, and a user friendly setup with push buttons and easy to read LCD menus. The advanced technology transmitter can function as an independent standalone system or as part of an integrated detection and transmission system. Using state of the art technology, the transmitter uses a magnetic want technique for performing non-intrusive calibration. For optimal stability and accurate readings, the unit provides an automatic zero drift correction feature. This also reduces the need for adjustments due to sensor aging.

The M2 Stand Alone Transmitter is available for LEL, H2S, CO, PPM, HC, CO2, CI2, NH3, SO2, HCN, and more. The unit also features an infrared sensor for CO2 and combustible gases. With 2 fully programmable alarms and a fail relay, the visual color coded LED alarms are reliable and customizable to meet specific needs.

Advanced sensor technology

The state of the art sensors are long lasting with a lifespan typically over two years. Sensor construction is rated Class I, Division 1 groups B, C, and D for flammables, CO, H2S, O2, and CO2. The sensors are rated Class I, Division 2 for all other toxic gases. Depending on the gas, the sensors will operate through a catalytic, galvanic cell, electrochemical, or infrared design. The plug in nature of the sensors allows for a quick and tool free onsite replacement.

Specifications

Each transmitter features 2 to 3 years of life with normal service. The explosion proof LEL H2 specific transmitter has 3 to 5 years with normal service, and the explosion proof carbon dioxide, methane, and hydrocarbons feature over 5 years of life with normal service. The explosion proof transmitters are also water repellant. Each device is approximately 8.5 H x 5.2 W x 4.5 D and features an alphanumeric display with a backlight. The screen displays 8 characters per line with 2 lines for gas concentration readouts.

Optional Accessories

The M2 Stand Alone Transmitter has a variety of optional accessories available including calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors or panels, and dataloggers. The transmitters are directly compatible with Beacon 110, 200, 410, and 800 controllers.

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

2811-731-001 EC 28 Gas Transmitter with Sensor, Sulfur Dioxide (SO2), No Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions