Ph Transmitter

pH3900 2-Wire pH Transmitter by Jenco

Industrial 2-wire pH transmitter with an isolated 4 ~20 mA current output with an LCD display for pH and is designed for pH electrodes with a built in RTD type Pt-100 ATC temperature sensor, meter is DC loop powered for DC voltages in the 11 to 50 VDC range and comes in a watertight IP-65 case and is easily wall mounted.

• Clear LCD displays pH
• Isolated 4 to 20 mA current output for pH
• Wide range power supply, 11 to 50 V DC
• Automatic temperature compensation
• Easy to install for wall setting
• IP65 watertight casing
• Isolated two wire 4 to 20 mA

PHMA pH Transmitter, 4-20mA, Blind by Sensorex

The Model PHMA (encapsulated miniature transmitter) is a 2-wire, 4-20 mA pH transmitter featuring encapsulated construction, high performance and small size. It can be interfaced with many display and control devices requiring a 4-20 mA input.

The unit is compatible will all SensoreX conventional combination pH electrodes. It transforms the pH signal to a 4-20 mA current proportional to the pH level. This output may be transmitted over two wires to a control location. The same two wires provide power to the transmitter. Any 12 - 36 Volt D.C. power supply may be used. There are two adjustments on the transmitter to standardize probes for "SPAN" and "ZERO". The output can be monitored with a loop-powered meter, a loop resistor or even a multi-meter during the standardization procedure.

• Compact size
• Easy-to-use
• 4-20mA loop-powered
• Adjustable zero and span
• Fully encapsulated

693-pH 2-wire 4-20 mA pH Transmitter by Jenco

2-wire 4-20 mA pH transmitter in a sealed NEMA-4 enclosure powered by 11 to 80 Volts DC. Span is fixed 0-14 pH. Connectors are BNC and tinned leads for 3-K Balco ATC sensor or simulation resistor.

• Input/output isolated
• Nema 4x enclosure
• 4 to 20 mA output
• High accuracy
• BNC input connector
• High input impedance
• Wide range power supply ,12 to 80 VDC

695-pH 2-wire 4-20 mA pH Transmitter by Jenco

2-wire 4-20 mA pH transmitter in a sealed NEMA-4 enclosure with an LCD display powered by 11 to 80 Volts DC. Span is selectable any 1 to 14 pH unit via internal dip switch. Connections are BNC for pH and tinned leads for 3-K Balco ATC sensor or simulation resistor.

• Input/output isolated
• Nema 4x enclosure
• Large LCD display
• 4 to 20 mA output
• High accuracy
• BNC input connector
• High input impedance
• 4 to 20 mA output scalable to any 1 pH or 100mv unit span (695pH/695ORP only)
• Manual/auto temp. compensation
• Wide range power supply ,12 to 80 VDC

GrowControl™ SXH Temp, pH, EC Transmitter by Agrowtek

GrowControl SXH is a precision digital sensor transmitter for temperature, pH, conductivity. SXH+ includes optional oxidation reduction potential or dissolved oxygen probe input. Optional color LCD display and button interface allows instant access to sensor readings, guided calibration, alarms, historical graphing and more.

Internal memory logs over 20,000 data points per sensor. Available with WiFi module for remote monitoring, data logging, alerts, and more. LX1 USB AgrowLink connects the GrowNET port to a PC for datalog download to .csv, graphing, calibration, configuration, updates, etc. using free PC software.

Connects to Agrowtek's GrowControl Cultivation Controllers as part of a complete facility control solution. LX2 ModLINK connects GrowNET™ devices to RS-422/485 for MODBUS RTU protocol.

Sensors

• Water Temperature: -20 - 60°C x 0.1°
• Conductivity: 0 - 5000uS x 10uS
• pH: 0 - 14pH x 0.01pH
• ORP or DO (+ model): +/-1000mv x 1mV; 0 - 20mg/mL x 0.1mg/mL
• Color LCD display for sensor monitoring & graphing optional
• Real Time Clock (RTC): Battery Backup Included

Features

• WiFi optional for direct sensor monitoring and web portal connection
• GrowNET link for connection to AgrowDose: Pumps or GrowControl™ master controller
• Available 4-20mA analog outputs: MODBUS RTU for industrial PLC applications
• Durable splash-proof ABS plastic enclosure: Conformal coated circuit boards
• 1-Year Warranty
• Made in USA

GrowControl™ SXHM Temp, pH, EC Transmitter by Agrowtek

GrowControl SXH is a precision digital sensor transmitter for temperature, pH, conductivity. SXH+ includes optional oxidation reduction potential or dissolved oxygen probe input. Optional color LCD display and button interface allows instant access to sensor readings, guided calibration, alarms, historical graphing and more.

Internal memory logs over 20,000 data points per sensor. Available with WiFi module for remote monitoring, data logging, alerts, and more. LX1 USB AgrowLink connects the GrowNET port to a PC for datalog download to .csv, graphing, calibration, configuration, updates, etc. using free PC software.

Connects to Agrowtek's GrowControl Cultivation Controllers as part of a complete facility control solution. LX2 ModLINK connects GrowNET™ devices to RS-422/485 for MODBUS RTU protocol.

Sensors

• Water Temperature: -20 - 60°C x 0.1°
• Conductivity: 0 - 5000uS x 10uS
• pH: 0 - 14pH x 0.01pH
• ORP or DO (+ model): +/-1000mv x 1mV; 0 - 20mg/mL x 0.1mg/mL
• Color LCD display for sensor monitoring & graphing optional
• Real Time Clock (RTC): Battery Backup Included

Features

• WiFi optional for direct sensor monitoring and web portal connection
• GrowNET link for connection to AgrowDose: Pumps or GrowControl™ master controller
• Available 4-20mA analog outputs: MODBUS RTU for industrial PLC applications
• Durable splash-proof ABS plastic enclosure: Conformal coated circuit boards
• 1-Year Warranty
• Made in USA

GrowControl™ PHX pH, Temp Transmitter by Agrowtek

GrowControl PHX and PHX+ are precision digital sensor transmitters for temperature and pH, plus optional ORP. Color LCD display and button interface model allows instant access to sensor readings, guided calibration, alarms, historical graphing and more.

Internal memory logs over 20,000 data points per sensor. Connects to Agrowtek's GrowControl Cultivation Controllers as part of a complete facility control solution. Available with WiFi module for stand-alone or remote monitoring, data logging, alerts, and more.

LX1 USB AgrowLink connects the GrowNET™ port to a PC with free PC software for datalog download, graphing, calibration, configuration, firmware updates, etc. LX2 ModLINK connects GrowNET™ devices to RS-422/485 for MODBUS RTU protocol communication.

Sensors

• Water Temperature: -20 - 60°C x 0.1°
• Conductivity: 0 - 5000uS x 10uS
• pH: 0 - 14pH x 0.01pH
• Color LCD display for sensor monitoring & graphing optional
• Real Time Clock (RTC): Battery Backup Included

Features

• WiFi optional for direct sensor monitoring and web portal connection
• GrowNET™ port for connection to AgrowDose Pumps, LX1 USB link or LX2 ModLINK
• MODBUS RTU for industrial PLC applications: Available 4-20mA analog outputs
• Durable splash-proof ABS plastic enclosure: Conformal coated circuit boards
• 1-Year Warranty
• Made in USA

GrowControl™ PHXM pH, Temp Transmitter by Agrowtek

GrowControl PHX and PHX+ are precision digital sensor transmitters for temperature and pH, plus optional ORP. Color LCD display and button interface model allows instant access to sensor readings, guided calibration, alarms, historical graphing and more.

Internal memory logs over 20,000 data points per sensor. Connects to Agrowtek's GrowControl Cultivation Controllers as part of a complete facility control solution. Available with WiFi module for stand-alone or remote monitoring, data logging, alerts, and more.

LX1 USB AgrowLink connects the GrowNET™ port to a PC with free PC software for datalog download, graphing, calibration, configuration, firmware updates, etc. LX2 ModLINK connects GrowNET™ devices to RS-422/485 for MODBUS RTU protocol communication.

Sensors

• Water Temperature: -20 - 60°C x 0.1°
• Conductivity: 0 - 5000uS x 10uS
• pH: 0 - 14pH x 0.01pH
• Color LCD display for sensor monitoring & graphing optional
• Real Time Clock (RTC): Battery Backup Included

Features

• WiFi optional for direct sensor monitoring and web portal connection
• GrowNET™ port for connection to AgrowDose Pumps, LX1 USB link or LX2 ModLINK
• MODBUS RTU for industrial PLC applications: Available 4-20mA analog outputs
• Durable splash-proof ABS plastic enclosure: Conformal coated circuit boards
• 1-Year Warranty
• Made in USA

692 1/8 DIN Panel Mount pH Transmitter with 4-20 mA Output by Jenco

1/8 DIN panel mount pH transmitter with 4-20 mA output and calibration by potentiometers. ATC temperature control uses a Pt-100 or simulation resistor. Features a large LCD display and uses a BNC input and spade lug screw type connector block.

• All solid state design
• ATC
• Low power consumption design, reduced internal heating thus increased reliability
• 0.56 high LCD display
• Isolated 4 to 20 mA current output
• High stability and fast response
• 1/8 DIN standard aluminum case
• Easy to install
• Heat cycled 100 hours before shipment

691N 1/8 DIN Panel Mount pH Transmitter with Calibration by Jenco

1/8 DIN panel mount pH transmitter with calibration by potentiometers. Has a manual temperature control knob and normal transmitter output of 4-20 mA output for 0-14 pH range or in expanded mode 4-2mA can be for any 2 pH units from 0 to 14 pH. Features a large bright red LED display. Connectors are a BNC pH input and spade lug screw type connector block. 115/230V AC.

• Current output with selectable span for better accuracy
• Manual temp. compensation
• 0.56 high efficiency red led display
• Low power consumption
• Reduced internal heating for increased reliability
• Heat cycled 100 hrs
• Isolated 4-20 mA output span of 0 to 14 pH over any 2 pH

6303C-pH Programmable Transmitter/Controller, LCD Display, 1/4 DIN by Jenco

The model 6303 is a precise instrument for the measurement and control of pH. It can also be used to measure but not control temperature and mV. A built-in micro- controller stores, calculates and compensates for all the parameters relating to pH determinations, such as the temperature characteristics of the pH electrode, pH electrode offset voltage and pH electrode slope deviations, etc.

3661 pH/ORP Controller/Transmitter Voltage Output, LED Display by Jenco

pH, ORP, Temperature In-line Controller. 1/8 DIN, RoHS compliant, panel mount pH/ORP/Temp controller with 2 sets of programmable on/off relay and backlight. Extremely price competitive.

• Easy to install 1/8 DIN plastic casing.
• Clear LCD displays pH, mV or temperature with backlight.
• Universal power supply input from 100 to 240 V AC.
• Automatic buffer recognition of US and NIST buffer sets. Calibrated data is stored in memory and ready to for use on power up.
• Automatic or manual temperature compensation.
• Displays absolute and relative ORP.
• Two sets of programmable on/off relays for pH or ORP & Isolated and reversible
• 4 to 20 mA current output for pH or ORP allows it to be used as a proportional output.
• CE, RoHs compliant.

3679N 1/4 DIN Panel Mount pH/ORP Controller/Transmitter by Jenco

1/4 DIN panel mount pH/ORP controller/transmitter in a waterproof IP-65 enclosure. Features, LCD display, dual SPDT Hi/Lo relays, manual set point adjust and pH calibration via potentiometers. For ORP there is a Zero Adjustment and pH/ORP is selectable via a shorting plug. Output is 4-20 mA current type. Connectors are a spade lug circular connector for pH+. All other connections are tinned leads to terminal blocks. Temperature compensation is a Pt-100 ATC or simulation resistor. Power 115/230V AC.

• Dual function pH & ORP
• Orp zero point calibration
• Isolated 4~20ma output
• Dual on/off relays
• Auto temperature compensation
• Water & corrosion proof case
• Large LCD display

3675 1/4 DIN Panel Mount pH/ORP Controller/Transmitter by Jenco

1/4 DIN panel mount pH/ORP controller/transmitter with dual SPDT Hi/Lo relays, manual set points and calibration are via potentiometers. Features a 4-20 mA current output and has an external pH/ORP select switch. Display is a large LCD. Connectors are a BNC and spade lug screw type connector blocks. Meter requires a Pt-100 ATC or a simulation resistor for temperature. Power 115/230V AC.

• Isolated 4 to 20 mA output
• Dual on/off relays
• Large LCD display
• ATC
• 115VAC /230VAC operations
• Compact 1/4 DIN case
• Low power solid state design
• Front panel output current span adjustable control
• Front panel acid/base influent select switch
• Front panel high/low relay format select switch

3676 1/4 DIN Panel Mount pH/ORP Controller/Transmitter by Jenco

1/4 DIN panel mount pH/ORP controller/transmitter with dual SPDT Hi/Lo relays, manual set points and calibration are via potentiometers. Features a 4-20 mA current output and has an external pH/ORP select switch. Display is a large bright red LED display. Connectors are a BNC input and spade lug screw type connector blocks. Meter requires a Pt-100 ATC or temp. simulation resistor. Power 115/230V AC.

• Isolated 4 to 20 mA output
• Dual on/off relays
• Large led display
• ATC
• 115VAC /230VAC operations
• Compact 1/4 DIN case
• Low power solid state design
• Front panel output current span adjustable control
• Front panel acid/base influent select switch
• Front panel high/low relay format select switch

WD-19066-06 Sensorex TX2000 1/4-DIN pH/ORP Transmitter/Controller; 100-240 VAC by Oakton

This full-featured pH/ORP transmitter/controller is designed for drinking water, wastewater, and general-purpose applications. The analyzer offers a wide range of features: two adjustable high/low relays, one wash control, and two isolated 4 to 20 mA outputs (one for the selected measurement and one for temperature), and enhanced measurement stability with sample averaging functionality. Automatic calibration with preset standards for up to three buffers. Calibration data can be password protected with a programmable security code.

• Large, graphical LCD with auto-sense backlight and contrast can be easily viewed in all lighting conditions
• Easy menu-driven operation with continuous diagnostic tests to ensure proper operation
• Dual diaplay with measurement and temperature
• Backup memory retains settings during power outage
• Automatic temperature compensation
• Up to 3-point calibration with USA or NIST buffers
• Panel- or wall-mount NEMA 4X, IP65 rated housing

TX3100 pH / ORP Transmitter, 1/2 Din by Sensorex

The TX3100 replaces the Sensorex TX3000 as our pH and ORP/mV monitoring instrument in a 1/2 DIN size.

This transmitter / controller can be used in a variety of water and wastewater monitoring applications, including industrial water and wastewater treatment, chemical processing, and environmental monitoring.

The TX3100 features brand new firmware and an updated user interface with user friendly text and graphical illustrations. This makes the instrument more intuitive to use compared with the older TX3000.

• Intelligent Graphic and Text Programming
• Large LCD display indicates pH or mV and temperature simultaneously
• NEMA 4X, IP65, 1/2 DIN enclosure
• Sample averaging to enhance stability
• Solution ground input eliminates reference ground potentials

TX105 pH/ORP Loop Powered 4-20mA Transmitter by Sensorex

Our TX105 is an isolated output 4-20mA industrial transmitter for reading pH or ORP sensors. Easily power the unit with available two-wire power supply loop. Ideal for connecting to a PLC for advanced control systems. Versatile mounting options for wall or panel mount. With a dual display LCD, monitoring both the measuring value and the temperature is simple. The TX105 is CE certified.

Features:

• Large LCD screen for easy reading
• Isolated 4-20 mA analog output
• Automatic temperature compensation
• Flexible mounting options

GrowControl™ SXHM+ Temp, pH, EC + ORP/DO Transmitter by Agrowtek

GrowControl SXH is a precision digital sensor transmitter for temperature, pH, conductivity. SXH+ includes optional oxidation reduction potential or dissolved oxygen probe input. Optional color LCD display and button interface allows instant access to sensor readings, guided calibration, alarms, historical graphing and more.

Internal memory logs over 20,000 data points per sensor. Available with WiFi module for remote monitoring, data logging, alerts, and more. LX1 USB AgrowLink connects the GrowNET port to a PC for datalog download to .csv, graphing, calibration, configuration, updates, etc. using free PC software.

Connects to Agrowtek's GrowControl Cultivation Controllers as part of a complete facility control solution. LX2 ModLINK connects GrowNET™ devices to RS-422/485 for MODBUS RTU protocol.

Sensors

• Water Temperature: -20 - 60°C x 0.1°
• Conductivity: 0 - 5000uS x 10uS
• pH: 0 - 14pH x 0.01pH
• ORP or DO (+ model): +/-1000mv x 1mV; 0 - 20mg/mL x 0.1mg/mL
• Color LCD display for sensor monitoring & graphing optional
• Real Time Clock (RTC): Battery Backup Included

Features

• WiFi optional for direct sensor monitoring and web portal connection
• GrowNET link for connection to AgrowDose: Pumps or GrowControl™ master controller
• Available 4-20mA analog outputs: MODBUS RTU for industrial PLC applications
• Durable splash-proof ABS plastic enclosure: Conformal coated circuit boards
• 1-Year Warranty
• Made in USA

GrowControl™ SXH+ Temp, pH, EC + ORP/DO Transmitter by Agrowtek

GrowControl SXH is a precision digital sensor transmitter for temperature, pH, conductivity. SXH+ includes optional oxidation reduction potential or dissolved oxygen probe input. Optional color LCD display and button interface allows instant access to sensor readings, guided calibration, alarms, historical graphing and more.

Internal memory logs over 20,000 data points per sensor. Available with WiFi module for remote monitoring, data logging, alerts, and more. LX1 USB AgrowLink connects the GrowNET port to a PC for datalog download to .csv, graphing, calibration, configuration, updates, etc. using free PC software.

Connects to Agrowtek's GrowControl Cultivation Controllers as part of a complete facility control solution. LX2 ModLINK connects GrowNET™ devices to RS-422/485 for MODBUS RTU protocol.

Sensors

• Water Temperature: -20 - 60°C x 0.1°
• Conductivity: 0 - 5000uS x 10uS
• pH: 0 - 14pH x 0.01pH
• ORP or DO (+ model): +/-1000mv x 1mV; 0 - 20mg/mL x 0.1mg/mL
• Color LCD display for sensor monitoring & graphing optional
• Real Time Clock (RTC): Battery Backup Included

Features

• WiFi optional for direct sensor monitoring and web portal connection
• GrowNET link for connection to AgrowDose: Pumps or GrowControl™ master controller
• Available 4-20mA analog outputs: MODBUS RTU for industrial PLC applications
• Durable splash-proof ABS plastic enclosure: Conformal coated circuit boards
• 1-Year Warranty
• Made in USA

GrowControl™ PHXM+ pH, Temp + ORP/DO Transmitter by Agrowtek

GrowControl PHX and PHX+ are precision digital sensor transmitters for temperature and pH, plus optional ORP. Color LCD display and button interface model allows instant access to sensor readings, guided calibration, alarms, historical graphing and more.

Internal memory logs over 20,000 data points per sensor. Connects to Agrowtek's GrowControl Cultivation Controllers as part of a complete facility control solution. Available with WiFi module for stand-alone or remote monitoring, data logging, alerts, and more.

LX1 USB AgrowLink connects the GrowNET™ port to a PC with free PC software for datalog download, graphing, calibration, configuration, firmware updates, etc. LX2 ModLINK connects GrowNET™ devices to RS-422/485 for MODBUS RTU protocol communication.

Sensors

• Water Temperature: -20 - 60°C x 0.1°
• Conductivity: 0 - 5000uS x 10uS
• pH: 0 - 14pH x 0.01pH
• Color LCD display for sensor monitoring & graphing optional
• Real Time Clock (RTC): Battery Backup Included

Features

• WiFi optional for direct sensor monitoring and web portal connection
• GrowNET™ port for connection to AgrowDose Pumps, LX1 USB link or LX2 ModLINK
• MODBUS RTU for industrial PLC applications: Available 4-20mA analog outputs
• Durable splash-proof ABS plastic enclosure: Conformal coated circuit boards
• 1-Year Warranty
• Made in USA

GrowControl™ PHX+ pH, Temp + ORP/DO Transmitter by Agrowtek

GrowControl PHX and PHX+ are precision digital sensor transmitters for temperature and pH, plus optional ORP. Color LCD display and button interface model allows instant access to sensor readings, guided calibration, alarms, historical graphing and more.

Internal memory logs over 20,000 data points per sensor. Connects to Agrowtek's GrowControl Cultivation Controllers as part of a complete facility control solution. Available with WiFi module for stand-alone or remote monitoring, data logging, alerts, and more.

LX1 USB AgrowLink connects the GrowNET™ port to a PC with free PC software for datalog download, graphing, calibration, configuration, firmware updates, etc. LX2 ModLINK connects GrowNET™ devices to RS-422/485 for MODBUS RTU protocol communication.

Sensors

• Water Temperature: -20 - 60°C x 0.1°
• Conductivity: 0 - 5000uS x 10uS
• pH: 0 - 14pH x 0.01pH
• Color LCD display for sensor monitoring & graphing optional
• Real Time Clock (RTC): Battery Backup Included

Features

• WiFi optional for direct sensor monitoring and web portal connection
• GrowNET™ port for connection to AgrowDose Pumps, LX1 USB link or LX2 ModLINK
• MODBUS RTU for industrial PLC applications: Available 4-20mA analog outputs
• Durable splash-proof ABS plastic enclosure: Conformal coated circuit boards
• 1-Year Warranty
• Made in USA

6503 ORP Transmitter/Controller with 1 ORP & 1 pH Inputs, 1/4 DIN by Jenco

1/4 DIN panel mount ORP controller/transmitter, microprocessor based, password protected with membrane keypad. LCD displays ORP or pH and temp. Meter has dual SPDT Hi/Lo relays, with programmable hysteresis and a reversible, isolated and programmable 4-20 mA output. Connectors are dual BNC for pH/ORP and spade lug type. ATC is 10K thermistor or simulation resistor. Power 115 / 230V AC

• Controls ORP & measures pH
• Offset calibration for ORP
• Set point security code protection
• Dual on/off relays
• 0.5 high LCD display
• Auto/manual temp. compensation
• Power down memory backup
• Audio feed back touch keys
• 1/4 DIN housing

TX100 pH/ORP Loop Powered Transmitter, 4-20mA, VDC, 1/4 DIN by Sensorex

The TX100 pH/mV transmitter is a loop-powered 4-20mA transmitter with a wide range of useful features and programmable options. Five buffer choices are available in two-point calibration mode. The 4-20mA output is scaleable in pH or mV units and has 500V input to output isolation. Temperature is always displayed and is selectable in °C or °F. All stored parameters and calibration data are retained in the non-volatile memory during transmitter power down or power loss. A useful probe clean reminder icon flashes when it is time to clean the probe. Probe cleaning interval is user programmable from 1 to 250 days. The TX100 can be used for wall mounting, panel mounting, pipe mounting and DIN-rail mounting. Cable grips for inlet/outlet to box are included as well as all mounting hardware. The case meets NEMA and IP ratings for water resistance.

Features:

• Displays readings in pH or mV alongisde temperature
• Mounts on wall, panel, pipe or DIN-rail
• Simple, easy to read user interface
• Probe cleaning reminder for easy maintenance
• Stores calibration and other data in case of power loss
• Water resistant case included