Natural Gas Detector

1316-002 G313 Single Gas Detector for Methane (Natural Gas), Propane, Refrigerant and other MOS Detectable VOCs, with NiMH Rechargeable Battery Pack by GfG

Pinpoint the Smallest Leaks

Small leaks in pipes or storage tanks can release enough gas to build up dangerous concentrations. The careful inspection of flanged, threaded and soldered connections before and after installation will ensure equipment and worker safety. The G300 leak detector will make leakage sprays a thing of the past

Clear and simple displays and warnings

Changing gas concentrations are indicated audibly and visually. The frequency of the audible warning rises with gas concentrations, allowing the user to pinpoint leaks. The bar graph display will warn the user if dangerous gas concentrations arise.

Light, compact and durable

Designed for one-handed operation, the G300 reacts to concentrations as small as 5 ppm and measures up to more than 10,000 ppm or 1% volume. The sensor is located at the end of a flexible gooseneck or a helix cable to allow the user to reach difficult or unreachable locations. The G300 is available with or without explosion protection for ammonia and combustible gases. The G311 operates on four "AA" alkaline batteries. All others have a rechargeable battery with run times of more than eight hours.

Features

• Small, light, and durable leak detector
• For combustible gases and ammonia
• More than 8 hours of continuous operation
• Explosion-proof models available

Standard Accessories

• G300 Detector
• Specified sensor
• Alkaline batteries or rechargeable NiMH battery pack as specified
• Charger (with rechargeable battery pack only)
• Fixed gooseneck (with alkaline battery pack only)
• Manual

SS4-AS2-C-E-M Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors by Honeywell Analytics

The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

Fire Sentry SS4-A

The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

Fire Sentry SS4-AS

The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

Fire Sentry SS4-AUV

The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

Operation

The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

Fire Sentry SS4-A and SS4-AS Features:

• Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
• Built-in test for optical "through the lens" testing
• False alarm immunity
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option
• Meets SIL 2 requirements

Fire Sentry SS4-AUV Features:

• Senses solar-blind ultraviolet band
• Built-in test for optical "through the lens" testing
• Utilises long-life, ruggedised UV sensors
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option

Applications include:

• Petrochemical facilities and Refineries
• Co-Generation plants
• Aircraft hangars
• Silane and Hydrogen gas storage
• Gas Turbines and power plants
• Gas compressor stations
• Warehouses
• Semiconductor

SS4-AS2-CSS-E-M Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 with MA420-4 4-20 mA Module for SS4 Detectors by Honeywell Analytics

The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

Fire Sentry SS4-A

The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

Fire Sentry SS4-AS

The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

Fire Sentry SS4-AUV

The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

Operation

The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

Fire Sentry SS4-A and SS4-AS Features:

• Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
• Built-in test for optical "through the lens" testing
• False alarm immunity
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option
• Meets SIL 2 requirements

Fire Sentry SS4-AUV Features:

• Senses solar-blind ultraviolet band
• Built-in test for optical "through the lens" testing
• Utilises long-life, ruggedised UV sensors
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option

Applications include:

• Petrochemical facilities and Refineries
• Co-Generation plants
• Aircraft hangars
• Silane and Hydrogen gas storage
• Gas Turbines and power plants
• Gas compressor stations
• Warehouses
• Semiconductor

SS4-AS2-C-E Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) M25 by Honeywell Analytics

The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

Fire Sentry SS4-A

The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

Fire Sentry SS4-AS

The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

Fire Sentry SS4-AUV

The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

Operation

The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

Fire Sentry SS4-A and SS4-AS Features:

• Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
• Built-in test for optical "through the lens" testing
• False alarm immunity
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option
• Meets SIL 2 requirements

Fire Sentry SS4-AUV Features:

• Senses solar-blind ultraviolet band
• Built-in test for optical "through the lens" testing
• Utilises long-life, ruggedised UV sensors
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option

Applications include:

• Petrochemical facilities and Refineries
• Co-Generation plants
• Aircraft hangars
• Silane and Hydrogen gas storage
• Gas Turbines and power plants
• Gas compressor stations
• Warehouses
• Semiconductor

SS4-AS2-C-E-H Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) M25 with SS4-FSCHCOM SS4 Module HART by Honeywell Analytics

The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

Fire Sentry SS4-A

The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

Fire Sentry SS4-AS

The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

Fire Sentry SS4-AUV

The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

Operation

The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

Fire Sentry SS4-A and SS4-AS Features:

• Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
• Built-in test for optical "through the lens" testing
• False alarm immunity
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option
• Meets SIL 2 requirements

Fire Sentry SS4-AUV Features:

• Senses solar-blind ultraviolet band
• Built-in test for optical "through the lens" testing
• Utilises long-life, ruggedised UV sensors
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option

Applications include:

• Petrochemical facilities and Refineries
• Co-Generation plants
• Aircraft hangars
• Silane and Hydrogen gas storage
• Gas Turbines and power plants
• Gas compressor stations
• Warehouses
• Semiconductor

SS4-AS2-H Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, FM, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with SS4-FSCHCOM SS4 Module HART by Honeywell Analytics

The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

Fire Sentry SS4-A

The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

Fire Sentry SS4-AS

The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

Fire Sentry SS4-AUV

The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

Operation

The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

Fire Sentry SS4-A and SS4-AS Features:

• Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
• Built-in test for optical "through the lens" testing
• False alarm immunity
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option
• Meets SIL 2 requirements

Fire Sentry SS4-AUV Features:

• Senses solar-blind ultraviolet band
• Built-in test for optical "through the lens" testing
• Utilises long-life, ruggedised UV sensors
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option

Applications include:

• Petrochemical facilities and Refineries
• Co-Generation plants
• Aircraft hangars
• Silane and Hydrogen gas storage
• Gas Turbines and power plants
• Gas compressor stations
• Warehouses
• Semiconductor

720B Combustible Gas Leak Detector by Test Products International

The 720B offers 10ppm sensitivity to detect combustible gasses. Easily operated with one hand, leaks are pinpointed using the audio and visual indicators. An adjustable tic rate helps eliminate background gas concentration in contaminated environments.

The 720b is an advanced state-of-the-art leak detector capable of detecting many combustible, noncombustible and toxic gases.

Features

• Instant response
• 10 ppm (methane) sensitivity
• Adjustable tic rate
• One-hand operation
• Visual and audible leak indication
• 16" gooseneck
• Soft carrying pouch
• Measurement capability

Applications

• Detect combustible gasses including natural gas methane, propane (LPG), gasoline, diesel, and kerosene
• Trace natural gas lines and fittings for leaks
• Check gas generation for leaks

The following is a partial list of gases that the 720b is sensitive to:

Acetone, Alcohol, Ammonia, Steam, Carbon Monoxide*, Butane, Gasoline, Jet Fuel, Hydrogen Sulfide, Smoke, Industrial Solvents, Methane, Lacquer Thinner, Naphtha, Propane, Natural Gas.

Standard accessories

• Sensor (A739)
• Instruction Manual: 720b Instruction Manual
• Soft Pouch (A700)

Optional accessories

• Hard Case (A714)
• Earphone (A710)

HXG-3 Combustible Gas Leak Detector by Test Products International

The HXG-3 offers 10ppm sensitivity to detect combustible gasses. Easily operated with new patent pending electronic tick control, leaks are pinpointed using the audio and visual indicators. Two line backlit LCD displays gas leaks in ppm and %LEL simultaneously.

Pinpoint Leaks

Leaks can easily be pinpointed by using an audible tick rate. The sensor is located at the end of a flexible gooseneck to easily reach areas where leaks may be suspected.

Data Save

A Data Save feature allows you to save data during any investigation.

Features

• Combustible Gas Leak Detector capable of displaying ppm or %LEL (Lower Explosive Limit).
• UL 913 intrinsic safety rating
• 10 ppm sensitivity (methane)
• Instant response
• Electronic tick rate control
• Settable alarm
• Visual and audible leak indication
• 16'' gooseneck
• Hard carrying case
• Displays LEL and PPM
• Infrared Downloading
• Long-life, Low-Cost Sensor
• Simple Calibration

Applications

• Confined Space Monitoring
• Vessel Testing
• Manhole Entry
• Vault Entry
• Leak Detection
• Leak Pinpointing
• Pipeline Purging

Partial List of Industries:

• Natural Gas Companies
• Propane Suppliers
• Electric Companies
• Safety Engineers
• Fire and Police
• Emergency Vehicles
• Appliance Repair
• Plant Maintenance
• Plumbing Contractors
• Marine Operations
• Heating and Air Conditioning
• Municipalities
• Mobile Home Parks
• Apartment Buildings

106223 Gas Laser Natural Gas Leak Detector by GMI

Highly advanced laser technology designed to detect natural gas with the aim of enhancing safety and improving detection for fire services, first responders and utility markets.

Features

• Quickly scan common venting points from a Safe Distance
• Highly visible, sunshine resistant Guide Laser equipped for location accuracy
• Graphical Interface for easy user interpretation
• Color Camera with Bluetooth, WiFi, and datalogging onboard
• Trusted Technology used in gas utility since 2005
• Certified Intrinsically Safe to Class I, Division 2, Group D

RGDME5MP1T BEAGLE Plus Natural Gas/Methane Gas Detector; with plug cable; Power supply: 110V~ by Seitron Americas

This is a plug&play version of the gas detector Beagle Plus. You just need to plug the device into the power supply and you are done.

Based on the gas you need to detect, you can choose among methan, LPG or CO version of the Beagle PLus.

Invisible enemies

A gas leak detector protects you from invisible enemies, which presence we can only detect when it is too late, or even never, such as in case of a carbon monoxide leak.

Every year around the world there are numerous accidents and fatalities due to gas leaks. Beagle Plus improves your house safety, and alert you in case of danger.

Quality and reliability

All Seitron gas leak detectors are made in Italy and undergo strict quality tests to ensure the highest quality level. Beagle and Segugio detectors are both IMQ certificated, and are compliant to international standards.

1316009 G311 Single Gas Detector for Methane (Natural Gas), Propane, and Other MOS Detectable VOCs, with 4 AA Alkaline Batteries by GfG

Pinpoint the Smallest Leaks

Small leaks in pipes or storage tanks can release enough gas to build up dangerous concentrations. The careful inspection of flanged, threaded and soldered connections before and after installation will ensure equipment and worker safety. The G300 leak detector will make leakage sprays a thing of the past

Clear and simple displays and warnings

Changing gas concentrations are indicated audibly and visually. The frequency of the audible warning rises with gas concentrations, allowing the user to pinpoint leaks. The bar graph display will warn the user if dangerous gas concentrations arise.

Light, compact and durable

Designed for one-handed operation, the G300 reacts to concentrations as small as 5 ppm and measures up to more than 10,000 ppm or 1% volume. The sensor is located at the end of a flexible gooseneck or a helix cable to allow the user to reach difficult or unreachable locations. The G300 is available with or without explosion protection for ammonia and combustible gases. The G311 operates on four "AA" alkaline batteries. All others have a rechargeable battery with run times of more than eight hours.

Features

• Small, light, and durable leak detector
• For combustible gases and ammonia
• More than 8 hours of continuous operation
• Explosion-proof models available

Standard Accessories

• G300 Detector
• Specified sensor
• Alkaline batteries or rechargeable NiMH battery pack as specified
• Charger (with rechargeable battery pack only)
• Fixed gooseneck (with alkaline battery pack only)
• Manual

SS4-AS2-CSS-E Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 by Honeywell Analytics

The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

Fire Sentry SS4-A

The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

Fire Sentry SS4-AS

The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

Fire Sentry SS4-AUV

The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

Operation

The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

Fire Sentry SS4-A and SS4-AS Features:

• Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
• Built-in test for optical "through the lens" testing
• False alarm immunity
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option
• Meets SIL 2 requirements

Fire Sentry SS4-AUV Features:

• Senses solar-blind ultraviolet band
• Built-in test for optical "through the lens" testing
• Utilises long-life, ruggedised UV sensors
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option

Applications include:

• Petrochemical facilities and Refineries
• Co-Generation plants
• Aircraft hangars
• Silane and Hydrogen gas storage
• Gas Turbines and power plants
• Gas compressor stations
• Warehouses
• Semiconductor

7900 Combustible Gas Sniffer / Leak Detector (with Rechargeable Battery) for detecting the presence of ANY combustible gases. (ex: Natural Gas, Methane, Propane, Gasoline, Kerosene, LPG, Hydrocarbons, etc.). Manual and automatic auto-zero, flexible probe, supplied with Carrying case, manual and batteries by Seitron Americas

Features

• Durable, Accurate and Highly Sensitive
• Detect any Combustible Hydrocarbon Gases (e.g. natural gas, LPG)
• Displays Readings in PPM, %Vol, & %L.E.L.
• Fast Response Time
• Auto-Zero Drift Adjustment
• Audible and Visual Alarms
• 11" Flexible Gooseneck Probe
• Field Replaceable Sensors

SS4-AS2-M Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, FM, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with MA420-4 4-20 mA Module for SS4 Detectors by Honeywell Analytics

The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

Fire Sentry SS4-A

The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

Fire Sentry SS4-AS

The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

Fire Sentry SS4-AUV

The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

Operation

The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

Fire Sentry SS4-A and SS4-AS Features:

• Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
• Built-in test for optical "through the lens" testing
• False alarm immunity
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option
• Meets SIL 2 requirements

Fire Sentry SS4-AUV Features:

• Senses solar-blind ultraviolet band
• Built-in test for optical "through the lens" testing
• Utilises long-life, ruggedised UV sensors
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option

Applications include:

• Petrochemical facilities and Refineries
• Co-Generation plants
• Aircraft hangars
• Silane and Hydrogen gas storage
• Gas Turbines and power plants
• Gas compressor stations
• Warehouses
• Semiconductor

SS4-AS2 Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Aluminum UV/IR, FM, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT by Honeywell Analytics

The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

Fire Sentry SS4-A

The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

Fire Sentry SS4-AS

The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

Fire Sentry SS4-AUV

The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

Operation

The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

Fire Sentry SS4-A and SS4-AS Features:

• Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
• Built-in test for optical "through the lens" testing
• False alarm immunity
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option
• Meets SIL 2 requirements

Fire Sentry SS4-AUV Features:

• Senses solar-blind ultraviolet band
• Built-in test for optical "through the lens" testing
• Utilises long-life, ruggedised UV sensors
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option

Applications include:

• Petrochemical facilities and Refineries
• Co-Generation plants
• Aircraft hangars
• Silane and Hydrogen gas storage
• Gas Turbines and power plants
• Gas compressor stations
• Warehouses
• Semiconductor

SS4-AS2-CSS-E-H Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non Latching Alarm LED, FM, cFM, IECEx for Zone 1 (2) M25 with SS4-FSCHCOM SS4 Module HART by Honeywell Analytics

The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

Fire Sentry SS4-A

The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

Fire Sentry SS4-AS

The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

Fire Sentry SS4-AUV

The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

Operation

The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

Fire Sentry SS4-A and SS4-AS Features:

• Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
• Built-in test for optical "through the lens" testing
• False alarm immunity
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option
• Meets SIL 2 requirements

Fire Sentry SS4-AUV Features:

• Senses solar-blind ultraviolet band
• Built-in test for optical "through the lens" testing
• Utilises long-life, ruggedised UV sensors
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option

Applications include:

• Petrochemical facilities and Refineries
• Co-Generation plants
• Aircraft hangars
• Silane and Hydrogen gas storage
• Gas Turbines and power plants
• Gas compressor stations
• Warehouses
• Semiconductor

SS4-AS2-SS Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, FM, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT by Honeywell Analytics

The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

Fire Sentry SS4-A

The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

Fire Sentry SS4-AS

The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

Fire Sentry SS4-AUV

The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

Operation

The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

Fire Sentry SS4-A and SS4-AS Features:

• Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
• Built-in test for optical "through the lens" testing
• False alarm immunity
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option
• Meets SIL 2 requirements

Fire Sentry SS4-AUV Features:

• Senses solar-blind ultraviolet band
• Built-in test for optical "through the lens" testing
• Utilises long-life, ruggedised UV sensors
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option

Applications include:

• Petrochemical facilities and Refineries
• Co-Generation plants
• Aircraft hangars
• Silane and Hydrogen gas storage
• Gas Turbines and power plants
• Gas compressor stations
• Warehouses
• Semiconductor

SS4-AS2-SS-H Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, FM, optimized for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with SS4-FSCHCOM SS4 Module HART Factory installed by Honeywell Analytics

The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

Fire Sentry SS4-A

The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

Fire Sentry SS4-AS

The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

Fire Sentry SS4-AUV

The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

Operation

The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

Fire Sentry SS4-A and SS4-AS Features:

• Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
• Built-in test for optical "through the lens" testing
• False alarm immunity
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option
• Meets SIL 2 requirements

Fire Sentry SS4-AUV Features:

• Senses solar-blind ultraviolet band
• Built-in test for optical "through the lens" testing
• Utilises long-life, ruggedised UV sensors
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option

Applications include:

• Petrochemical facilities and Refineries
• Co-Generation plants
• Aircraft hangars
• Silane and Hydrogen gas storage
• Gas Turbines and power plants
• Gas compressor stations
• Warehouses
• Semiconductor

SS4-AS2-SS-M Multi-Spectrum Electro-Optical Digital Fire & Flame Detector, Stainless Steel UV/IR, FM, optimised for Non-Hydrocarbons and Silane, Ethanol, Methanol, Hydrogen & Natural Gas Fires, Non-latching Alarm LED, FM, cFM, CSFM for Class I, Div.1 groups B,C & D (2) 3/4 NPT with MA420-4 4-20 mA Module for SS4 by Honeywell Analytics

The Fire Sentry SS4 Electro-Optical Digital Fire and Flame Detectors represent leading edge UV and UV/IR technology.

Fire Sentry SS4-A

The Fire Sentry SS4-A represents the world's pre-eminent UV/IR technology for ElectroOptical Flame Detectors with tens of thousands successfully operating in a multitude of installations worldwide. This multi-spectrum detector senses radiant energy in the ultraviolet (UV), visible and wide band Infrared™ (IR) spectrum. The radiant energy from all types of flaming fires will alert the detector to their presence.

To eliminate common nuisance false alarms that occasionally occur with UV-only, IR-only, Dual IR or Dual Mode UV/IR detectors, the Fire Sentry SS4 detectors' FireLogic signal processing requires that UV, visible and wide band IR radiant energy all be evaluated before declaring a fire. The smart detector utilises real-time signal processing algorithms that are optimised to alarm on all types of fires, while virtually eliminating the possibility of false alarms.

Fire Sentry SS4-AS

The Fire Sentry SS4-AS processes UV, IR and Visible (VIS) spectral ranges from ruggedised solar-blind UV, "Quantum-Effect" IR and VIS sensors correspondingly. It is optimised for detection of hydrogen, ethanol, methanol and methane (natural gas) fires and like the other detectors in its family, it responds to Type A, B and C flaming fires.

Fire Sentry SS4-AUV

The Fire Sentry SS4-AUV represents the leading edge technology UV optical flame detectors. This flame detector senses radiant energy in the ultraviolet (UV) spectrum. The radiant emissions of flaming fires will alert the detector to their presence. The SS4-AUV is for indoor applications where UV sources such as welding are not present.

Operation

The Fire Sentry SS4 detectors operate from standard 24 Volt DC power and interface to approved fire alarm panels or standard PLC's. On power up, a self-test is performed and the fault relay resets to show no faults. The front LED lights flash every ten seconds to indicate power is on.

The continuous spectral data stream of information from the sensor array is analysed by the microprocessor. Upon alarm, the detector activates the alarm relay and stores all the pre-fire spectral data in non-volatile memory for retrieval and evaluation. This Fire Pic™ data can be used to postulate the cause of the fire. As part of the FS2000™ System, the SS4 family of detectors communicate with CM1-A Controller via a four wire bi-directional RS-485 FireBus™.

The field of view for the Fire Sentry SS4 detectors is the widest in the industry with a 120° cone of vision. This means more hazard area can be covered by each detector. Greater sensitivity also increases the volume covered by each detector; up to four times more than some other detectors.

Using sophisticated microprocessor signal processing algorithms, false alarm rejection is maximised - with virtual immunity to false alarms from arc welding, corona discharge and other common non-fire sources.

Fire Sentry SS4-A and SS4-AS Features:

• Multi-Spectrum™: senses ultraviolet, visible and wide band Infrared™
• Built-in test for optical "through the lens" testing
• False alarm immunity
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microprocessor based algorithms: FirePic™, Snapshot™ and Tri-Mode Plot™
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option
• Meets SIL 2 requirements

Fire Sentry SS4-AUV Features:

• Senses solar-blind ultraviolet band
• Built-in test for optical "through the lens" testing
• Utilises long-life, ruggedised UV sensors
• Detects hydrocarbon and non-hydrocarbon based fires
• Wide field-of-view and solar-blind
• Adjustable detector sensitivity
• Microcomputer based algorithms: FirePic&trad;, Snapshot™ and UV Plot
• Wide temperature range of operation
• Compatible with standard approved fire alarm panels
• Explosion-proof housing
• Time programmable alarm verification
• mA output option

Applications include:

• Petrochemical facilities and Refineries
• Co-Generation plants
• Aircraft hangars
• Silane and Hydrogen gas storage
• Gas Turbines and power plants
• Gas compressor stations
• Warehouses
• Semiconductor

735A Gas Leak Detector by Test Products International

Designed to quickly and accurately measure natural and propane gas leaks, as well as carbon monoxide concentrations.

Features

• Internal Pump
• Water/Dust Filter
• Push Button Operation
• Field Calibration
• Date/Time Display
• Calibration Alert
• Operation Memory
• Calibration Memory
• Infrared Download
• Audible/Visual Alarms
• Backlit LCD
• Programmable Auto Shut Off

Applications

• Gas Leak Survey/Investigations
• Confined Space Monitoring
• Gas Emergency Investigations
• Vessel Testing

Standard Accessories

• Carrying Pouch (A780)
• Instruction Manual
• Battery and Sensor (Installed and Calibrated)

725 Pocket Combustible Gas Detector by Test Products International

The 725 offers 1000ppm sensitivity to detect combustible gasses including natural gas, methane, propane (LPG), diesel, and kerosene.

Trace fuel lines, tanks and containers for gas leaks. Once a leak is detected, the 725 will sound an alarm and the red LED s will light showing level of leak.

Features

• 1000ppm sensitivity
• Trace natural gas lines and fittings for leaks
• Check gas equipment for leaks
• Test propane tanks, fittings, lines, and heaters for leaks
• Check propane tanks, fitting lines, and heaters for leaks.
• Test confined spaces for gas build-up
• Fits in shirt pocket
• Responds instantly

Applications

• Check gas generation for leaks

Standard Accessories

• Carrying Pouch (A780)
• Instruction Manual
• Battery and Sensor (Installed and Calibrated)

719 Combustible Gas Leak Detector by Test Products International

The 719 offers 30ppm sensitivity to detect combustible gasses. Easily operated with one hand, leaks are pinpointed using the audio and visual indicators. An adjustable tic rate helps eliminate background gas concentration in contaminated environments.

The 719 is easy to use and is built to last. It is backed by a 3 year limited warranty. Please remember to complete and return your product warranty registration card.

Features

• Instant response
• 30 ppm (methane) sensitivity
• Adjustable tic rate
• One-hand operation
• Visual and audible leak indication
• 16'' gooseneck
• Soft carrying pouch

Applications

• Detect combustible gasses including natural gas methane, propane (LPG), gasoline, diesel, and kerosene
• Trace natural gas lines and fittings for leaks
• Check gas generation for leaks

The 719 comes complete with the following accessories:

• Carrying Pouch (A780)
• Instruction Manual
• Battery and Sensor (Installed and Calibrated)

HXG-2D Combustible Gas Leak Detector by Test Products International

The HXG-2D offers 10ppm sensitivity to detect combustible gasses. Easily operated with new patent pending electronic tick control, leaks are pinpointed using the audio and visual indicators. Backlit LCD display of gas leaks in ppm or %LEL.

Features

• Combustible Gas Leak Detector capable of displaying ppm or %LEL (Lower Explosive Limit).
• Designed to meet UL 913 intrinsic safety (Approval Pending)
• 10 ppm sensitivity (methane)
• Instant response
• Electronic tick rate control
• Settable alarm
• Visual and audible leak indication
• 16'' gooseneck
• Hard carrying case

Applications

• Detect combustible gasses including natural gas methane, propane (LPG), gasoline, diesel, and kerosene
• Trace natural gas lines and fittings for leaks
• Check gas generation for leaks

How big is the leak?

• Direct PPM readout
• Direct "LEL" percent readout

Find Leaks Quickly

• New "Patent Pending" electronic tick control
• Ideal for Natural, Propane and Butane gas leaks

Safe, Durable and Reliable

• Intrinsically safe design
• SENSIT "ruggedized" design

Partial List of Industries:

• Utility Companies
• Gas Processing Plants
• Propane Marketers
• Safety Engineers
• Fire and Police
• Emergency Vehicles
• Appliance Repair
• Plant Maintenance
• Plumbing Contractors
• Furnace Heat Exchanger Testing
• Marine Operations
• Heating and Air Conditioning
• Municipalities
• Mobile Home Parks
• Apartment Buildings

VPE Ultrasonic Leak Detector by Superior AccuTrak

The Patented Superior AccuTrak® VPE represents state-of-the-art technology for pinpointing leaks is air conditioning and refrigeration systems. AccuTrak® is extremely sensitive to the ultrasonic sound of a turbulent gas leak. Using a technology called "heterodyning" it translates the sound to a lower frequency which your ear can interpret. AccuTrak maintains the original sound characteristics making it possible to distinguish leaks from other competing background sounds. AccuTrak is so sensitive you can actually hear the blink of an eye, yet most background noise will not interfere with detection accuracy.

VPE Basic Kit

Superior AccuTrak® advanced patented technology has never been so affordable! The AccuTrak® VPE Basic Kit is for technicians who require only the essentials to detect leaks using airborne ultrasound. As with all AccuTrak® instruments, the VPE finds leaks for any kind of gas or refrigerant without changing tips or components. Works equally well to find compressed air leaks, nitrogen leaks even vacuum leaks! AccuTrak® can find leaks as small as the equivalent of 1.5 oz per year of refrigerant, or can hear a 5 psi leak up to 30 feet away.

Kit Includes:

• VPE Leak Detector
• Headset
• Battery
• Hard Case

VPE Standard Kit

The AccuTrak® VPE Standard Kit offers literally twice the functionality of the Basic Kit with the addition of the AccuTrak® Touch Probe and Waveguide. Utilizing the Touch Probe, the VPE can troubleshoot thermal expansion valves in less than 5 minutes, and find faulty steam traps in just seconds! The Touch Probe can also be used to detect worn bearings and faulty valves. With the Waveguide attachment a technician can gain better access to hard-to-reach places and better determine the location of leaks that would otherwise be inaccessible. This is our most popular kit for a reason!

Kit Includes:

• VPE Leak Detector
• Headset
• Battery
• Hard Case
• Touch Probe
• Waveguide

VPE Professional Kit

The AccuTrak® VPE Professional Kit is designed for technicians who work in noisy places, or who regularly need to find smaller leaks. The VPE Professional Kit includes all the great features of our VPE Standard Kit upgraded with professional Noise Cancelling Headphones and a larger case to keep everything together. These high quality headphones eliminate all background noise, allowing a technician to effectively find the smallest leaks even in very loud environments. You can choose the standard style professional headphones, or the hardhat compatible version same price!

Kit Includes:

• VPE Leak Detector
• Battery
• Touch Probe
• Waveguide
• Noise Blocking Headphones
• Large Carry Case

VPE Plus Kit

The AccuTrak® VPE Plus Kit is designed for technicians looking to take full advantage of all the VPE s many capabilities. The VPE Plus Kit includes everything in our Standard Kit PLUS our powerful Burst Tone Sound Generator! The sophisticated Burst Tone can artificially pressurize any vessel or space with ultrasonic sound, allowing a technician to quickly scan for leaks even where there is no actual pressure differential! The VPE Plus Kit is ideal for technicians who test refrigerator door and window seals, or any other non-pressurized seal or vessel. The VPE Plus Kit is also great for Energy Audits and Surveys, and finding air leaks and sources of air infiltration in homes, aircraft, ships, and buildings.

Kit Includes:

• VPE Leak Detector
• Headset
• Battery
• Hard Case
• Touch Probe
• Waveguide
• Sound Generator

VPE Pro-Plus Kit

The AccuTrak® VPE Pro-Plus Kit is our most comprehensive VPE Kit, for the serious technician who needs the maximum capability from an ultrasonic instrument. The VPE Pro-Plus Kit includes the upgraded professional Noise Cancelling Headphones PLUS the powerful Burst Tone Sound Generator, in the larger case to keep everything together. The VPE Pro-Plus Kit offers unrivaled functionality and versatility for a fraction of the cost of any competitive system with similar performance. Find any kind of leak, troubleshoot internal mechanical problems, find bad gaskets and door seals and do it all well, in any environment! If you do a variety of work, and need a cost effective professional kit that can do it all, the Superior AccuTrak® VPE Pro-Plus Kit is for you.

Kit Includes:

• VPE Leak Detector
• Battery
• Touch Probe
• Waveguide
• Sound Generator
• Noise Blocking Headphones
• Large Carry Case

Applications:

• Leak Detection: Air, Vacuum, Refrigerants; ANY GAS!
• Steam Traps: Detect live steam loss in seconds!
• Valves: Detect/hear internal leakage in check, ball, needle, gate or any type of valve! Diagnose thermal expansion valves in just five minutes!
• Bearing Wear: Hear wear and lubrication problems before damage is done!

Features:

• Audio Output: 0 Hz to 4 kHz Natural Sound conversion allows you to Hear the Leak, and distinguish leaks from mechanical or other background ultrasound.
• Visual Output: 10 element bar graph provides quick and intuitive visual indication to presence of and relative strength of ultrasound.
• Adjustable Sensitivity: allows operator to quickly identify leaks from a distance, and then zero in on the exact location of the leak.

Capabilities:

• Capable of detecting a 5 psi leak out of a 0.005" (5/1000 inch) hole, 20 to 30 feet away depending on background noise.
• Easily detects any gas that generates ultrasonic sound during flow including vacuum leaks.
• Capable of detecting leaks equivalent to 1.5 oz/year of Refrigerant.
• Works equally well for compressed Air or Nitrogen.
• Not affected by wind or high concentrations of leaked gas or refrigerant.

Kits for Every Application

Whether you only need the basic functions of the VPE or you plan to take full advantage of the instrument's diverse capabilities, we have a kit that will meet your needs! Click the "Find Your Kit" tab above to learn more.

Advantages Versus Sniffers

• AccuTrak® VPE is a much more accurate and reliable instrument for detecting single and multiple leaks.
• AccuTrak® VPE can detect any type of refrigerant gas including nitrogen.
• AccuTrak® VPE detects both vacuum and pressure leaks.
• AccuTrak® VPE is effective in gas saturated areas and under windy conditions.
• AccuTrak® VPE does not require the introduction of tracer gases into the system, which can be ozone depleting when vented, and can also be harmful to ones health.
• AccuTrak® VPE is battery powered for cordless operation

Advantages versus other Ultrasonic Leak Detectors

• AccuTrak® VPE is #1 in technology. We wrote the book on ultrasonic leak detection, our patented instruments lead the industry!
• AccuTrak® VPE is the original! it is not a copy.
• AccuTrak® VPE is the most durable unit available, with the best warranty. The face of the unit is sealed with no pin holes/speakers for foreign objects to enter.
• AccuTrak® VPE has more dynamic range, and wont overload in loud areas.
• AccuTrak® VPE gives true audio sound reproduction instead of the "beeps and squeals" of other instruments.