Methanol

ME1000-G Methanol (Methyl Alcohol), ACS, 4L by AquaPhoenix

• CAS No. 67-56-1
• CH3OH FW=32.04
• Methanol/UN1230

Specifications

• Packaging Type: Glass
• Grade: ACS
• Size: 4.00 L

ME1000-P Methanol (Methyl Alcohol), ACS, 500mL by AquaPhoenix

• CAS No. 67-56-1
• CH3OH FW=32.04
• Methanol/UN1230

Specifications

• Packaging Type: Glass
• Grade: ACS
• Size: 500 mL

ME1000-Q Methanol (Methyl Alcohol), ACS, 1L by AquaPhoenix

• CAS No. 67-56-1
• CH3OH FW=32.04
• Methanol/UN1230

Specifications

• Packaging Type: Glass
• Grade: ACS
• Size: 1.00 L

XGSBC Xgard IR Spare Sensor Modules, 0-100% LEL, methanol by Crowcon

Xgard IR is an explosion-proof gas detector which uses a dual-wavelength infrared sensor to provide highly dependable detection of hazardous gases and vapors. Based on Crowcon's hugely successful Xgard design, Xgard IR offers the many advantages of infrared sensor technology in a rugged and versatile package including: failsafe sensor technology, immune to poisoning, no damage by over-gassing, fast response and suitable for use in inert atmospheres.

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

2214028 CS 21 Fixed Gas Transmitter, Methanol (CH₄O), 0(30) - 1,000 ppm by GfG

The CS 21 transmitter uses the proven chemosorption detection principle for detection of toxic gases, vapors and combustibles. The rapid response of the transmitter provides opportunity to take counter measures and thereby limit damages. The long life of the sensors makes the CS 21 a low-cost solution for your detection needs. A transmitter can be continuously operated for more than 5 years.

Wall mount installation is straightforward. The distance between transmitter and controller can be greater than 500 m. A rugged aluminum casing protects the sensor and electronics from splashes of water and dirt. The transmitter must not be operated in EX-areas. For measurement of combustible gases in the LEL range the gas needs to be sampled by pump. In this case the EX-protection needs to be guaranteed with suitable external components (e.g.flame-protection).

• High sensitivity to a broad range of refrigerants
• Long sensor life
• Fast response

RM-5003MEOH-485 Module, Indicator/Alarm, 0-100 %LEL methanol (CH3OH), 3-wire 4-20 mA, with RS-485 output, RM-5000 Series by RKI Instruments

Features

• Compatible with RM-570A/580 series
• Bar meter and digital multi-indication
• High level of visibility
• Low power consumption
• Support RS-485 communication function
• RoHS Compliant
• Global standard

Applications

• LPG, LNG utilities
• Refineries
• Chemical plants
• Semi-conductor manufacturing plants
• Engineering, public works
• Power station
• Iron and steel works
• Automative Planting Processes

*Please note we can only ship RKI products to customers within the United States

2801-32-002 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-100% LEL (MK 208-1), Methanol (CH4O), Display by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

CC22-772-DM CC 22 Series Fixed Transmitter with Methanol (CH₄O) Sensor, 0 - 100% LEL Range, Display / Modbus by GfG

Are you looking for an innovative and cost-effective transmitter for combustible gases, but without the need for explosion protection? Then a GfG 22 series transmitter is the right choice.

Time-proven and innovative

The CC 22 works according to the heat of reaction principle, a proven method for measuring combustible gases. The transmitters are fitted with high-performance electronics for voltage stabilization, processing of readings, and temperature compensation. Follow-up costs are minimized thanks to the long lifespan of the sensors.

Universal signal transmission

Either an analog or digital output signal can be transmitted by the CC 22 by means of a Modbus interface. Due to the different types of signal transmission, a 22 series transmitter can be connected to almost any gas detection system, also as an extra measuring point or as a replacement transmitter on existing systems.

Signal processing

The embedded software of the CC 22 linearises the measuring signal and compensates for the effects of temperature. As a result, correct readings are transmitted even with weather related fluctuations in temperature. The software allows problems to be detected, and the Modbus version also indicates any required service or maintenance work.

Weather protection

A weatherproof housing not only protects transmitters against exposure to wind and weather, but also against contamination and excessive temperatures caused by direct sunlight.

Optional colored graphic display

The clear graphic display of the CC 22 is self explanatory and allows you to read off the current status and other important information with ease. The display enables you to navigate effortlessly through the unit's concise menu and to change settings or even calibrate, depending on your user authorization. In the event of an alarm, the display will turn red.

Operation buttons

The buttons on the transmitter allow the unit to be calibrated and settings to be adjusted through the menu as needed.

The application areas of the dust and water-protected structure range from production and storage areas to disposal sites, biogas plants, mines and oil rigs.

Calibration adapter

In order to perform regular bump tests, a calibration adapter is used on the transmitter, which ensures a uniform and secure supply of gas.

Easy and convenient service

GfG offers full after-the-sale commissioning and field service support.

Features

• Uses the catalytic combustion principle
• Long service life of the sensors
• High efficiency and low follow-up costs
• Sturdy plastic housing (IP 54)
• Cost effective single-man adjustment
• Affordable solution for many measuring tasks

3300-32-001 CC 33 Fixed Transmitter with Methanol (CH4O), Aluminum Housing, 0-100% LEL (MK 208-3), 4-20 mA No Relay by GfG

It has always been our aspiration to combine innovative ideas and technology with functional design. This is how quality and longevity come about. Attributes symbolic of the name GfG in gas measurement.

Are you looking for an innovative transmitter for flammable gases, but need explosion protection? Then a transmitter from the GfG 33 series is the right choice.

Robust housing for every application

The transmitters of the 33 series are flameproof encapsulated and fulfill the requirements of the type of protection "d". Depending on the application, you can choose the 33 transmitter with an epoxy-based aluminum or a pure stainless steel housing. In order to meet the quality requirements of our customers and our own standards in terms of durability, we use a particularly high-quality and durable Viton seal in the 33 series. This can withstand even the toughest operating conditions for many years.

Variants

GfG offers the CC 33 in two variants:

For conventional industrial The CC 33 is available in a lacquered die-cast aluminum housing with 10mm thick bulletproof glass. Applications with special conditions such as e.g. in the Food industry can be covered by a unpainted housing made of stainless steel with a 15mm thick bulletproof glass.

Operation by means of magnetic pin

The three magnetic switches behind the protective glass, which is up to 15mm thick, can be operated using the GfG magnetic pin. The GfG typical three-button operation is easy to understand. The menu is clearly structured and logically structured.

All transmitters of the 22, 29 and 33 series have a uniform user interface. The uniform operation and the logical system structure keep your training and maintenance effort as low as possible.

Proven and innovative is not a contradiction

The CC 33 works on the principle of catalytic heat generation (WT), a proven method for measuring combustible gases. The transmitters are equipped with high-performance electronics for voltage stabilization, processing of measured value output and temperature compensation. The long life of the sensors minimizes follow-up costs.

Sensor technology

With improved sensor technology and the unique GfG "chimney effect", the CC 33 transmitter for combustible gases has one of the fastest response times in the world. There are more crucial seconds left to initiate countermeasures and to bring people to safety.

Universal signal transmission

The measured values and status displays of the 33 series can be transmitted either analog or digital via the Modbus interface. Due to the different variants of signal transmission, a transmitter of the 33 series can be connected to almost any gas warning system as an additional measuring point or in exchange for existing transducers.

Signal processing

The embedded software of the 33 transmitter linearises the measurement signal and compensates for temperature influences. As a result, correct measured values are transmitted even in the event of weather-related temperature fluctuations. The execution of the software enables the detection of faults and, in the Modbus variant, the requirement of required service or maintenance work.

Smart sensors

Pre-calibrated sensor modules can be screwed directly into the sensor receptacle on the housing of the CC 33. The smart GfG sensors are pre-programmed with all the necessary parameters and can be used without much effort ("plug and play"). Sensor changes are shown in the display. (catalytic and electrochemical sensors)

Three freely programmable internal relays

The 33er transmitters can be used as a "stand-alone system". You can set the two alarm thresholds individually and freely program the optional three relays. You do not need a cable to a controller and you can nevertheless reliably switch safety-related devices.

With colored graphic display

The clearly laid-out graphic display makes it easy to read the device status, the current measured value and many other important information. In the event of an alarm, the display turns red. The large LEDs signal from a distance the current device status and thus serve the rapid information of your employees about any alarms or malfunctions.

Using the display, you can easily navigate through the clear device menu and make various settings, including calibration, depending on your user authorization.

Calibration

For regular function control with gas application, a calibration adapter is placed on the transmitter to ensure a safe and even gas supply.

3300-32-002 CC 33 Fixed Transmitter with Methanol (CH4O), Aluminum Housing, 0-100% LEL (MK 208-3), 4-20 mA with Relay by GfG

It has always been our aspiration to combine innovative ideas and technology with functional design. This is how quality and longevity come about. Attributes symbolic of the name GfG in gas measurement.

Are you looking for an innovative transmitter for flammable gases, but need explosion protection? Then a transmitter from the GfG 33 series is the right choice.

Robust housing for every application

The transmitters of the 33 series are flameproof encapsulated and fulfill the requirements of the type of protection "d". Depending on the application, you can choose the 33 transmitter with an epoxy-based aluminum or a pure stainless steel housing. In order to meet the quality requirements of our customers and our own standards in terms of durability, we use a particularly high-quality and durable Viton seal in the 33 series. This can withstand even the toughest operating conditions for many years.

Variants

GfG offers the CC 33 in two variants:

For conventional industrial The CC 33 is available in a lacquered die-cast aluminum housing with 10mm thick bulletproof glass. Applications with special conditions such as e.g. in the Food industry can be covered by a unpainted housing made of stainless steel with a 15mm thick bulletproof glass.

Operation by means of magnetic pin

The three magnetic switches behind the protective glass, which is up to 15mm thick, can be operated using the GfG magnetic pin. The GfG typical three-button operation is easy to understand. The menu is clearly structured and logically structured.

All transmitters of the 22, 29 and 33 series have a uniform user interface. The uniform operation and the logical system structure keep your training and maintenance effort as low as possible.

Proven and innovative is not a contradiction

The CC 33 works on the principle of catalytic heat generation (WT), a proven method for measuring combustible gases. The transmitters are equipped with high-performance electronics for voltage stabilization, processing of measured value output and temperature compensation. The long life of the sensors minimizes follow-up costs.

Sensor technology

With improved sensor technology and the unique GfG "chimney effect", the CC 33 transmitter for combustible gases has one of the fastest response times in the world. There are more crucial seconds left to initiate countermeasures and to bring people to safety.

Universal signal transmission

The measured values and status displays of the 33 series can be transmitted either analog or digital via the Modbus interface. Due to the different variants of signal transmission, a transmitter of the 33 series can be connected to almost any gas warning system as an additional measuring point or in exchange for existing transducers.

Signal processing

The embedded software of the 33 transmitter linearises the measurement signal and compensates for temperature influences. As a result, correct measured values are transmitted even in the event of weather-related temperature fluctuations. The execution of the software enables the detection of faults and, in the Modbus variant, the requirement of required service or maintenance work.

Smart sensors

Pre-calibrated sensor modules can be screwed directly into the sensor receptacle on the housing of the CC 33. The smart GfG sensors are pre-programmed with all the necessary parameters and can be used without much effort ("plug and play"). Sensor changes are shown in the display. (catalytic and electrochemical sensors)

Three freely programmable internal relays

The 33er transmitters can be used as a "stand-alone system". You can set the two alarm thresholds individually and freely program the optional three relays. You do not need a cable to a controller and you can nevertheless reliably switch safety-related devices.

With colored graphic display

The clearly laid-out graphic display makes it easy to read the device status, the current measured value and many other important information. In the event of an alarm, the display turns red. The large LEDs signal from a distance the current device status and thus serve the rapid information of your employees about any alarms or malfunctions.

Using the display, you can easily navigate through the clear device menu and make various settings, including calibration, depending on your user authorization.

Calibration

For regular function control with gas application, a calibration adapter is placed on the transmitter to ensure a safe and even gas supply.

3300-32-003 CC 33 Fixed Transmitter with Methanol (CH4O), Aluminum Housing, 0-100% LEL (MK 208-3), RS 485 No Relay by GfG

It has always been our aspiration to combine innovative ideas and technology with functional design. This is how quality and longevity come about. Attributes symbolic of the name GfG in gas measurement.

Are you looking for an innovative transmitter for flammable gases, but need explosion protection? Then a transmitter from the GfG 33 series is the right choice.

Robust housing for every application

The transmitters of the 33 series are flameproof encapsulated and fulfill the requirements of the type of protection "d". Depending on the application, you can choose the 33 transmitter with an epoxy-based aluminum or a pure stainless steel housing. In order to meet the quality requirements of our customers and our own standards in terms of durability, we use a particularly high-quality and durable Viton seal in the 33 series. This can withstand even the toughest operating conditions for many years.

Variants

GfG offers the CC 33 in two variants:

For conventional industrial The CC 33 is available in a lacquered die-cast aluminum housing with 10mm thick bulletproof glass. Applications with special conditions such as e.g. in the Food industry can be covered by a unpainted housing made of stainless steel with a 15mm thick bulletproof glass.

Operation by means of magnetic pin

The three magnetic switches behind the protective glass, which is up to 15mm thick, can be operated using the GfG magnetic pin. The GfG typical three-button operation is easy to understand. The menu is clearly structured and logically structured.

All transmitters of the 22, 29 and 33 series have a uniform user interface. The uniform operation and the logical system structure keep your training and maintenance effort as low as possible.

Proven and innovative is not a contradiction

The CC 33 works on the principle of catalytic heat generation (WT), a proven method for measuring combustible gases. The transmitters are equipped with high-performance electronics for voltage stabilization, processing of measured value output and temperature compensation. The long life of the sensors minimizes follow-up costs.

Sensor technology

With improved sensor technology and the unique GfG "chimney effect", the CC 33 transmitter for combustible gases has one of the fastest response times in the world. There are more crucial seconds left to initiate countermeasures and to bring people to safety.

Universal signal transmission

The measured values and status displays of the 33 series can be transmitted either analog or digital via the Modbus interface. Due to the different variants of signal transmission, a transmitter of the 33 series can be connected to almost any gas warning system as an additional measuring point or in exchange for existing transducers.

Signal processing

The embedded software of the 33 transmitter linearises the measurement signal and compensates for temperature influences. As a result, correct measured values are transmitted even in the event of weather-related temperature fluctuations. The execution of the software enables the detection of faults and, in the Modbus variant, the requirement of required service or maintenance work.

Smart sensors

Pre-calibrated sensor modules can be screwed directly into the sensor receptacle on the housing of the CC 33. The smart GfG sensors are pre-programmed with all the necessary parameters and can be used without much effort ("plug and play"). Sensor changes are shown in the display. (catalytic and electrochemical sensors)

Three freely programmable internal relays

The 33er transmitters can be used as a "stand-alone system". You can set the two alarm thresholds individually and freely program the optional three relays. You do not need a cable to a controller and you can nevertheless reliably switch safety-related devices.

With colored graphic display

The clearly laid-out graphic display makes it easy to read the device status, the current measured value and many other important information. In the event of an alarm, the display turns red. The large LEDs signal from a distance the current device status and thus serve the rapid information of your employees about any alarms or malfunctions.

Using the display, you can easily navigate through the clear device menu and make various settings, including calibration, depending on your user authorization.

Calibration

For regular function control with gas application, a calibration adapter is placed on the transmitter to ensure a safe and even gas supply.

3300-32-004 CC 33 Fixed Transmitter with Methanol (CH4O), Aluminum Housing, 0-100% LEL (MK 208-3), RS 485 with Relay by GfG

It has always been our aspiration to combine innovative ideas and technology with functional design. This is how quality and longevity come about. Attributes symbolic of the name GfG in gas measurement.

Are you looking for an innovative transmitter for flammable gases, but need explosion protection? Then a transmitter from the GfG 33 series is the right choice.

Robust housing for every application

The transmitters of the 33 series are flameproof encapsulated and fulfill the requirements of the type of protection "d". Depending on the application, you can choose the 33 transmitter with an epoxy-based aluminum or a pure stainless steel housing. In order to meet the quality requirements of our customers and our own standards in terms of durability, we use a particularly high-quality and durable Viton seal in the 33 series. This can withstand even the toughest operating conditions for many years.

Variants

GfG offers the CC 33 in two variants:

For conventional industrial The CC 33 is available in a lacquered die-cast aluminum housing with 10mm thick bulletproof glass. Applications with special conditions such as e.g. in the Food industry can be covered by a unpainted housing made of stainless steel with a 15mm thick bulletproof glass.

Operation by means of magnetic pin

The three magnetic switches behind the protective glass, which is up to 15mm thick, can be operated using the GfG magnetic pin. The GfG typical three-button operation is easy to understand. The menu is clearly structured and logically structured.

All transmitters of the 22, 29 and 33 series have a uniform user interface. The uniform operation and the logical system structure keep your training and maintenance effort as low as possible.

Proven and innovative is not a contradiction

The CC 33 works on the principle of catalytic heat generation (WT), a proven method for measuring combustible gases. The transmitters are equipped with high-performance electronics for voltage stabilization, processing of measured value output and temperature compensation. The long life of the sensors minimizes follow-up costs.

Sensor technology

With improved sensor technology and the unique GfG "chimney effect", the CC 33 transmitter for combustible gases has one of the fastest response times in the world. There are more crucial seconds left to initiate countermeasures and to bring people to safety.

Universal signal transmission

The measured values and status displays of the 33 series can be transmitted either analog or digital via the Modbus interface. Due to the different variants of signal transmission, a transmitter of the 33 series can be connected to almost any gas warning system as an additional measuring point or in exchange for existing transducers.

Signal processing

The embedded software of the 33 transmitter linearises the measurement signal and compensates for temperature influences. As a result, correct measured values are transmitted even in the event of weather-related temperature fluctuations. The execution of the software enables the detection of faults and, in the Modbus variant, the requirement of required service or maintenance work.

Smart sensors

Pre-calibrated sensor modules can be screwed directly into the sensor receptacle on the housing of the CC 33. The smart GfG sensors are pre-programmed with all the necessary parameters and can be used without much effort ("plug and play"). Sensor changes are shown in the display. (catalytic and electrochemical sensors)

Three freely programmable internal relays

The 33er transmitters can be used as a "stand-alone system". You can set the two alarm thresholds individually and freely program the optional three relays. You do not need a cable to a controller and you can nevertheless reliably switch safety-related devices.

With colored graphic display

The clearly laid-out graphic display makes it easy to read the device status, the current measured value and many other important information. In the event of an alarm, the display turns red. The large LEDs signal from a distance the current device status and thus serve the rapid information of your employees about any alarms or malfunctions.

Using the display, you can easily navigate through the clear device menu and make various settings, including calibration, depending on your user authorization.

Calibration

For regular function control with gas application, a calibration adapter is placed on the transmitter to ensure a safe and even gas supply.

2801-32-001 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-100% LEL (MK 208-1), Methanol (CH4O), No Display by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

2801-32-003 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-100% LEL (MK 208-1), Methanol (CH4O), Display / Alarm by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

CC22-772 CC 22 Series Fixed Transmitter with Methanol (CH₄O) Sensor, 0 - 100% LEL Range, No Display / 4-20 mA by GfG

Are you looking for an innovative and cost-effective transmitter for combustible gases, but without the need for explosion protection? Then a GfG 22 series transmitter is the right choice.

Time-proven and innovative

The CC 22 works according to the heat of reaction principle, a proven method for measuring combustible gases. The transmitters are fitted with high-performance electronics for voltage stabilization, processing of readings, and temperature compensation. Follow-up costs are minimized thanks to the long lifespan of the sensors.

Universal signal transmission

Either an analog or digital output signal can be transmitted by the CC 22 by means of a Modbus interface. Due to the different types of signal transmission, a 22 series transmitter can be connected to almost any gas detection system, also as an extra measuring point or as a replacement transmitter on existing systems.

Signal processing

The embedded software of the CC 22 linearises the measuring signal and compensates for the effects of temperature. As a result, correct readings are transmitted even with weather related fluctuations in temperature. The software allows problems to be detected, and the Modbus version also indicates any required service or maintenance work.

Weather protection

A weatherproof housing not only protects transmitters against exposure to wind and weather, but also against contamination and excessive temperatures caused by direct sunlight.

Optional colored graphic display

The clear graphic display of the CC 22 is self explanatory and allows you to read off the current status and other important information with ease. The display enables you to navigate effortlessly through the unit's concise menu and to change settings or even calibrate, depending on your user authorization. In the event of an alarm, the display will turn red.

Operation buttons

The buttons on the transmitter allow the unit to be calibrated and settings to be adjusted through the menu as needed.

The application areas of the dust and water-protected structure range from production and storage areas to disposal sites, biogas plants, mines and oil rigs.

Calibration adapter

In order to perform regular bump tests, a calibration adapter is used on the transmitter, which ensures a uniform and secure supply of gas.

Easy and convenient service

GfG offers full after-the-sale commissioning and field service support.

Features

• Uses the catalytic combustion principle
• Long service life of the sensors
• High efficiency and low follow-up costs
• Sturdy plastic housing (IP 54)
• Cost effective single-man adjustment
• Affordable solution for many measuring tasks

CC22-772-D CC 22 Series Fixed Transmitter with Methanol (CH₄O) Sensor, 0 - 100% LEL Range, Display / 4-20 mA by GfG

Are you looking for an innovative and cost-effective transmitter for combustible gases, but without the need for explosion protection? Then a GfG 22 series transmitter is the right choice.

Time-proven and innovative

The CC 22 works according to the heat of reaction principle, a proven method for measuring combustible gases. The transmitters are fitted with high-performance electronics for voltage stabilization, processing of readings, and temperature compensation. Follow-up costs are minimized thanks to the long lifespan of the sensors.

Universal signal transmission

Either an analog or digital output signal can be transmitted by the CC 22 by means of a Modbus interface. Due to the different types of signal transmission, a 22 series transmitter can be connected to almost any gas detection system, also as an extra measuring point or as a replacement transmitter on existing systems.

Signal processing

The embedded software of the CC 22 linearises the measuring signal and compensates for the effects of temperature. As a result, correct readings are transmitted even with weather related fluctuations in temperature. The software allows problems to be detected, and the Modbus version also indicates any required service or maintenance work.

Weather protection

A weatherproof housing not only protects transmitters against exposure to wind and weather, but also against contamination and excessive temperatures caused by direct sunlight.

Optional colored graphic display

The clear graphic display of the CC 22 is self explanatory and allows you to read off the current status and other important information with ease. The display enables you to navigate effortlessly through the unit's concise menu and to change settings or even calibrate, depending on your user authorization. In the event of an alarm, the display will turn red.

Operation buttons

The buttons on the transmitter allow the unit to be calibrated and settings to be adjusted through the menu as needed.

The application areas of the dust and water-protected structure range from production and storage areas to disposal sites, biogas plants, mines and oil rigs.

Calibration adapter

In order to perform regular bump tests, a calibration adapter is used on the transmitter, which ensures a uniform and secure supply of gas.

Easy and convenient service

GfG offers full after-the-sale commissioning and field service support.

Features

• Uses the catalytic combustion principle
• Long service life of the sensors
• High efficiency and low follow-up costs
• Sturdy plastic housing (IP 54)
• Cost effective single-man adjustment
• Affordable solution for many measuring tasks

CC22-772-M CC 22 Series Fixed Transmitter with Methanol (CH₄O) Sensor, 0 - 100% LEL Range, No Display / Modbus by GfG

Are you looking for an innovative and cost-effective transmitter for combustible gases, but without the need for explosion protection? Then a GfG 22 series transmitter is the right choice.

Time-proven and innovative

The CC 22 works according to the heat of reaction principle, a proven method for measuring combustible gases. The transmitters are fitted with high-performance electronics for voltage stabilization, processing of readings, and temperature compensation. Follow-up costs are minimized thanks to the long lifespan of the sensors.

Universal signal transmission

Either an analog or digital output signal can be transmitted by the CC 22 by means of a Modbus interface. Due to the different types of signal transmission, a 22 series transmitter can be connected to almost any gas detection system, also as an extra measuring point or as a replacement transmitter on existing systems.

Signal processing

The embedded software of the CC 22 linearises the measuring signal and compensates for the effects of temperature. As a result, correct readings are transmitted even with weather related fluctuations in temperature. The software allows problems to be detected, and the Modbus version also indicates any required service or maintenance work.

Weather protection

A weatherproof housing not only protects transmitters against exposure to wind and weather, but also against contamination and excessive temperatures caused by direct sunlight.

Optional colored graphic display

The clear graphic display of the CC 22 is self explanatory and allows you to read off the current status and other important information with ease. The display enables you to navigate effortlessly through the unit's concise menu and to change settings or even calibrate, depending on your user authorization. In the event of an alarm, the display will turn red.

Operation buttons

The buttons on the transmitter allow the unit to be calibrated and settings to be adjusted through the menu as needed.

The application areas of the dust and water-protected structure range from production and storage areas to disposal sites, biogas plants, mines and oil rigs.

Calibration adapter

In order to perform regular bump tests, a calibration adapter is used on the transmitter, which ensures a uniform and secure supply of gas.

Easy and convenient service

GfG offers full after-the-sale commissioning and field service support.

Features

• Uses the catalytic combustion principle
• Long service life of the sensors
• High efficiency and low follow-up costs
• Sturdy plastic housing (IP 54)
• Cost effective single-man adjustment
• Affordable solution for many measuring tasks