Gas Analyzer

716A740 716 Flue Gas Analyzer Kit by Test Products International

Features

• Built-in differential manometer with 0.001 H2O resolution
• Calculates combustion efficiency
• Data Logging with time and date stamp
• Will not shut off if 15 ppm CO is present for increased safety
• Communicate to a PC via the USB interface
• Optional A740 IR printer available for hard copies of test results
• Built-in differential thermometer
• Push on fittings for fast and easy use
• Optional Bluetooth interface

A740 Features

• Easy to use
• Battery operated
• Self test facility
• Adjustable contrast
• Manual paper feed
• Maximum transmitting distance 16"(45cm)

Includes

• 716 Flue Gas Analyzer
• A740 IR Printer

72-2120A-101 Digester Gas Analyzer, 100%vol CH4 by RKI Instruments

RKI is proud to introduce our Digester Gas Monitor. Gas from waste digesters contains high levels of methane, CO2, and H2S, with little to no oxygen present. The RKI gas monitor checks for all these gases on a cyclic basis. A powerful air aspirator draws a sample from up to 100 feet away. Since digester gas contains high humidity and high H2S, both of which can cause damage to sampling systems, the RKI Digester Gas Monitor is designed to handle these with no damage to the sampling system or sensors. The sample is passed through a series of dirt, dust, and moisture stopping filters, and these filters are automatically purged with fresh air at the end of each cycle.

Measurement time is just 4 minutes, taken at periodic cycles. Cycle time is selectable, with settings for cycle time of 15 minute, 1 hour, 4 hours, 8 hours, or 24 hours. A cycle can also be initiated anytime by pressing a button. After each cycle, the sensors and sampling system are flushed with fresh air so as to minimize corrosion caused by the high H2S content. The system is fault tolerant minimizing the possibility of expensive repairs or downtime.

System integrity is maintained at all times using a flow fail monitoring device which provides a fail alarm and relay if there is ever a problem with the flow system, such as a blockage, or if the air aspirator compressed air supply is removed or interrupted.

The system is housed in a wall mounting NEMA 4X enclosure. The gas readings can be viewed through the enclosure door clear window. Flow meters and filters are easily visible for confirmation of correct flows and operation. The RKI Digester Gas Monitor contains adjustable alarm levels for each gas, and also programmable alarm relays. In addition, the unit provides 4-20mA signals for each gas concentration for connection to an external DCS, PLC, or other site control system. A Modbus output is also available. The outputs are the readings received from the last cycle taken.

Features:

• Corrosion resistant design; Housing designed for extreme environments; Internal construction for extreme samples; Flow system designed to handle corrosive wet samples
• Sample system designed to handle high humidity
• Accurately measures gases with high levels of H2S present
• 100 ft. sample range
• Up to 4 sensors: Methane 0-100% Volume; CO2 0-50% Volume; Oxygen 0-25% Volume; H2S 0-1000 PPM (0-3000 or 0-5000 optional)
• Self draining moisture trap
• Automatic backflush of sampling system
• Long life air aspirator (no moving parts)
• Suitable for inside/outside installations
• NEMA 4X enclosure
• Uses proven RKI technology
• Modular design easy to maintain
• Simple to operate

Industry Applications:

• Wastewater Treatment Digesters
• Biogas Methane
• Animal Farms

*Please note we can only ship RKI products to customers within the United States

72-2120A-102 Digester Gas Analyzer, 100%vol CH4 by RKI Instruments

RKI is proud to introduce our Digester Gas Monitor. Gas from waste digesters contains high levels of methane, CO2, and H2S, with little to no oxygen present. The RKI gas monitor checks for all these gases on a cyclic basis. A powerful air aspirator draws a sample from up to 100 feet away. Since digester gas contains high humidity and high H2S, both of which can cause damage to sampling systems, the RKI Digester Gas Monitor is designed to handle these with no damage to the sampling system or sensors. The sample is passed through a series of dirt, dust, and moisture stopping filters, and these filters are automatically purged with fresh air at the end of each cycle.

Measurement time is just 4 minutes, taken at periodic cycles. Cycle time is selectable, with settings for cycle time of 15 minute, 1 hour, 4 hours, 8 hours, or 24 hours. A cycle can also be initiated anytime by pressing a button. After each cycle, the sensors and sampling system are flushed with fresh air so as to minimize corrosion caused by the high H2S content. The system is fault tolerant minimizing the possibility of expensive repairs or downtime.

System integrity is maintained at all times using a flow fail monitoring device which provides a fail alarm and relay if there is ever a problem with the flow system, such as a blockage, or if the air aspirator compressed air supply is removed or interrupted.

The system is housed in a wall mounting NEMA 4X enclosure. The gas readings can be viewed through the enclosure door clear window. Flow meters and filters are easily visible for confirmation of correct flows and operation. The RKI Digester Gas Monitor contains adjustable alarm levels for each gas, and also programmable alarm relays. In addition, the unit provides 4-20mA signals for each gas concentration for connection to an external DCS, PLC, or other site control system. A Modbus output is also available. The outputs are the readings received from the last cycle taken.

Features:

• Corrosion resistant design; Housing designed for extreme environments; Internal construction for extreme samples; Flow system designed to handle corrosive wet samples
• Sample system designed to handle high humidity
• Accurately measures gases with high levels of H2S present
• 100 ft. sample range
• Up to 4 sensors: Methane 0-100% Volume; CO2 0-50% Volume; Oxygen 0-25% Volume; H2S 0-1000 PPM (0-3000 or 0-5000 optional)
• Self draining moisture trap
• Automatic backflush of sampling system
• Long life air aspirator (no moving parts)
• Suitable for inside/outside installations
• NEMA 4X enclosure
• Uses proven RKI technology
• Modular design easy to maintain
• Simple to operate

Industry Applications:

• Wastewater Treatment Digesters
• Biogas Methane
• Animal Farms

*Please note we can only ship RKI products to customers within the United States

72-2120A-104 Digester Gas Analyzer, 50%vol CO2 by RKI Instruments

RKI is proud to introduce our Digester Gas Monitor. Gas from waste digesters contains high levels of methane, CO2, and H2S, with little to no oxygen present. The RKI gas monitor checks for all these gases on a cyclic basis. A powerful air aspirator draws a sample from up to 100 feet away. Since digester gas contains high humidity and high H2S, both of which can cause damage to sampling systems, the RKI Digester Gas Monitor is designed to handle these with no damage to the sampling system or sensors. The sample is passed through a series of dirt, dust, and moisture stopping filters, and these filters are automatically purged with fresh air at the end of each cycle.

Measurement time is just 4 minutes, taken at periodic cycles. Cycle time is selectable, with settings for cycle time of 15 minute, 1 hour, 4 hours, 8 hours, or 24 hours. A cycle can also be initiated anytime by pressing a button. After each cycle, the sensors and sampling system are flushed with fresh air so as to minimize corrosion caused by the high H2S content. The system is fault tolerant minimizing the possibility of expensive repairs or downtime.

System integrity is maintained at all times using a flow fail monitoring device which provides a fail alarm and relay if there is ever a problem with the flow system, such as a blockage, or if the air aspirator compressed air supply is removed or interrupted.

The system is housed in a wall mounting NEMA 4X enclosure. The gas readings can be viewed through the enclosure door clear window. Flow meters and filters are easily visible for confirmation of correct flows and operation. The RKI Digester Gas Monitor contains adjustable alarm levels for each gas, and also programmable alarm relays. In addition, the unit provides 4-20mA signals for each gas concentration for connection to an external DCS, PLC, or other site control system. A Modbus output is also available. The outputs are the readings received from the last cycle taken.

Features:

• Corrosion resistant design; Housing designed for extreme environments; Internal construction for extreme samples; Flow system designed to handle corrosive wet samples
• Sample system designed to handle high humidity
• Accurately measures gases with high levels of H2S present
• 100 ft. sample range
• Up to 4 sensors: Methane 0-100% Volume; CO2 0-50% Volume; Oxygen 0-25% Volume; H2S 0-1000 PPM (0-3000 or 0-5000 optional)
• Self draining moisture trap
• Automatic backflush of sampling system
• Long life air aspirator (no moving parts)
• Suitable for inside/outside installations
• NEMA 4X enclosure
• Uses proven RKI technology
• Modular design easy to maintain
• Simple to operate

Industry Applications:

• Wastewater Treatment Digesters
• Biogas Methane
• Animal Farms

*Please note we can only ship RKI products to customers within the United States

72-2120A-203 Digester Gas Analyzer, 100%vol CH4/50%vol CO2 by RKI Instruments

RKI is proud to introduce our Digester Gas Monitor. Gas from waste digesters contains high levels of methane, CO2, and H2S, with little to no oxygen present. The RKI gas monitor checks for all these gases on a cyclic basis. A powerful air aspirator draws a sample from up to 100 feet away. Since digester gas contains high humidity and high H2S, both of which can cause damage to sampling systems, the RKI Digester Gas Monitor is designed to handle these with no damage to the sampling system or sensors. The sample is passed through a series of dirt, dust, and moisture stopping filters, and these filters are automatically purged with fresh air at the end of each cycle.

Measurement time is just 4 minutes, taken at periodic cycles. Cycle time is selectable, with settings for cycle time of 15 minute, 1 hour, 4 hours, 8 hours, or 24 hours. A cycle can also be initiated anytime by pressing a button. After each cycle, the sensors and sampling system are flushed with fresh air so as to minimize corrosion caused by the high H2S content. The system is fault tolerant minimizing the possibility of expensive repairs or downtime.

System integrity is maintained at all times using a flow fail monitoring device which provides a fail alarm and relay if there is ever a problem with the flow system, such as a blockage, or if the air aspirator compressed air supply is removed or interrupted.

The system is housed in a wall mounting NEMA 4X enclosure. The gas readings can be viewed through the enclosure door clear window. Flow meters and filters are easily visible for confirmation of correct flows and operation. The RKI Digester Gas Monitor contains adjustable alarm levels for each gas, and also programmable alarm relays. In addition, the unit provides 4-20mA signals for each gas concentration for connection to an external DCS, PLC, or other site control system. A Modbus output is also available. The outputs are the readings received from the last cycle taken.

Features:

• Corrosion resistant design; Housing designed for extreme environments; Internal construction for extreme samples; Flow system designed to handle corrosive wet samples
• Sample system designed to handle high humidity
• Accurately measures gases with high levels of H2S present
• 100 ft. sample range
• Up to 4 sensors: Methane 0-100% Volume; CO2 0-50% Volume; Oxygen 0-25% Volume; H2S 0-1000 PPM (0-3000 or 0-5000 optional)
• Self draining moisture trap
• Automatic backflush of sampling system
• Long life air aspirator (no moving parts)
• Suitable for inside/outside installations
• NEMA 4X enclosure
• Uses proven RKI technology
• Modular design easy to maintain
• Simple to operate

Industry Applications:

• Wastewater Treatment Digesters
• Biogas Methane
• Animal Farms

*Please note we can only ship RKI products to customers within the United States

72-2120A-205 Digester Gas Analyzer, 25%vol O2/50%vol CO2 by RKI Instruments

RKI is proud to introduce our Digester Gas Monitor. Gas from waste digesters contains high levels of methane, CO2, and H2S, with little to no oxygen present. The RKI gas monitor checks for all these gases on a cyclic basis. A powerful air aspirator draws a sample from up to 100 feet away. Since digester gas contains high humidity and high H2S, both of which can cause damage to sampling systems, the RKI Digester Gas Monitor is designed to handle these with no damage to the sampling system or sensors. The sample is passed through a series of dirt, dust, and moisture stopping filters, and these filters are automatically purged with fresh air at the end of each cycle.

Measurement time is just 4 minutes, taken at periodic cycles. Cycle time is selectable, with settings for cycle time of 15 minute, 1 hour, 4 hours, 8 hours, or 24 hours. A cycle can also be initiated anytime by pressing a button. After each cycle, the sensors and sampling system are flushed with fresh air so as to minimize corrosion caused by the high H2S content. The system is fault tolerant minimizing the possibility of expensive repairs or downtime.

System integrity is maintained at all times using a flow fail monitoring device which provides a fail alarm and relay if there is ever a problem with the flow system, such as a blockage, or if the air aspirator compressed air supply is removed or interrupted.

The system is housed in a wall mounting NEMA 4X enclosure. The gas readings can be viewed through the enclosure door clear window. Flow meters and filters are easily visible for confirmation of correct flows and operation. The RKI Digester Gas Monitor contains adjustable alarm levels for each gas, and also programmable alarm relays. In addition, the unit provides 4-20mA signals for each gas concentration for connection to an external DCS, PLC, or other site control system. A Modbus output is also available. The outputs are the readings received from the last cycle taken.

Features:

• Corrosion resistant design; Housing designed for extreme environments; Internal construction for extreme samples; Flow system designed to handle corrosive wet samples
• Sample system designed to handle high humidity
• Accurately measures gases with high levels of H2S present
• 100 ft. sample range
• Up to 4 sensors: Methane 0-100% Volume; CO2 0-50% Volume; Oxygen 0-25% Volume; H2S 0-1000 PPM (0-3000 or 0-5000 optional)
• Self draining moisture trap
• Automatic backflush of sampling system
• Long life air aspirator (no moving parts)
• Suitable for inside/outside installations
• NEMA 4X enclosure
• Uses proven RKI technology
• Modular design easy to maintain
• Simple to operate

Industry Applications:

• Wastewater Treatment Digesters
• Biogas Methane
• Animal Farms

*Please note we can only ship RKI products to customers within the United States

0563 3104 01 310 II - Flue Gas Analyzer by Testo

The new testo 310 II flue gas analyzer combines simple functions with a high level of measurement accuracy, and is perfect for all basic measurements on heating systems. Long battery lifetimes of more than eight hours guarantee the analyzer is ready. Simultaneous, individual measurement and display of the measurement parameters in the instrument's high-resolution display are easily possible. The display can be easily configured via the testo Smart App and translates to the 310 II. Its easy handling and compact design make the testo 310 II a robust tool for daily work – even when things get rough.

The printer with Bluetooth® interface, specially developed for the testo 310 II, allows you to create clear reports on site as required. The current measurement value can be printed out of any measurement menu during or after the measurement. Via the simple connection to the testo Smart App, further measurements as well as digital documentation, data transfer and digital customer data management can be performed simultaneously. The testo 310 II offers all advantages of electronic flue gas measurement in high quality at a perfect cost-benefit ratio.

• Simultaneous, individual measurement and display of all relevant measurement parameters (O2, CO, CO2, flue gas and ambient temperature, CO environment, draft and pressure). Display configurable via the testo Smart App.
• Simultaneous, additional measurements via the testo Smart App (e.g. gas flow pressure, flow and return temperature)
• Easy and intuitive menu guidance
• Data documented and sent digitally via testo Smart App
• Digital customer data management via testo Smart App
• Rechargeable lithium battery for over 8 hours of operation
• Robust construction
• Sensor zeroing in 30 seconds

0563 3105 01 310 II - Flue Gas Analyzer with Printer by Testo

The new testo 310 II flue gas analyzer combines simple functions with a high level of measurement accuracy, and is perfect for all basic measurements on heating systems. Long battery lifetimes of more than eight hours guarantee the analyzer is ready. Simultaneous, individual measurement and display of the measurement parameters in the instrument's high-resolution display are easily possible. The display can be easily configured via the testo Smart App and translates to the 310 II. Its easy handling and compact design make the testo 310 II a robust tool for daily work – even when things get rough.

The printer with Bluetooth® interface, specially developed for the testo 310 II, allows you to create clear reports on site as required. The current measurement value can be printed out of any measurement menu during or after the measurement. Via the simple connection to the testo Smart App, further measurements as well as digital documentation, data transfer and digital customer data management can be performed simultaneously. The testo 310 II offers all advantages of electronic flue gas measurement in high quality at a perfect cost-benefit ratio.

• Simultaneous, individual measurement and display of all relevant measurement parameters (O2, CO, CO2, flue gas and ambient temperature, CO environment, draft and pressure). Display configurable via the testo Smart App.
• Simultaneous, additional measurements via the testo Smart App (e.g. gas flow pressure, flow and return temperature)
• Easy and intuitive menu guidance
• Data documented and sent digitally via testo Smart App
• Digital customer data management via testo Smart App
• Rechargeable lithium battery for over 8 hours of operation
• Robust construction
• Sensor zeroing in 30 seconds

4500-2 BTU4500 Gas Emissions Analyzer by E Instruments

BTU4500 (2 Gas) for O2, CO, CO2 Included. Upgradeable to Add NO/NOx, NO2, SO2 or CxHy (4-Gas Analyzer) BUILT-IN, NON-THERMAL Printer + Paper Rolls Software Included (save and email reports) (SW KIT) High Range CO Sensor (0-50,000 ppm) Auto Dilution

Accurate / Reliable / Robust / Fast

• Up to FOUR (4) Gas Sensors
• Automatic Data Logging
• Total NOx Capable
• Draft & Differential Pressure
• Dilution Pump for CO Auto-Range Measurements up to 10,000 ppm
• Combustion Efficiency
• PC Software with Bluetooth®

• O2, CO, NO, NO2, SO2, CxHy (HC)
• Built-In Printer Non-Fading Paper
• Full Color Graphic Display
• Field Replaceable Sensors
• PC Software with Bluetooth®
• iOS and Android Mobile Applications

Standard Probe & Hose:

• 12" (300mm) Probe
• 1470 °F (800 °C) max
• 10' (3m) Dual Hose

Long Probe & Hose:

• 30" (750mm) Probe
• 1470 °F (800 °C) max
• 10' (3m) Dual Hose

Long & High Temp Probe & Hose:

• 40" (1m) Probe or 60'' (1.5m) Probe
• 2190 °F (1200 °C) max
• 10' (3m) Hose

Hose Extentions:

• 10' (3m) Length Available

All BTU4500 Kits Include:

• Built-In Printer
• New iOS & Android App (Remote Display & QR Scanning)
• CO2 % Calculation
• Combustion Efficiency, Losses, & Excess Air Calculations
• Draft & Differential Pressure
• Incoming Air Temperature for Condensing Boilers
• Temperature Measurements
• Large Color Display
• 2000 Test Internal Memory
• Bluetooth Connectivity
• Long Lasting Rechargeable Battery & AC Charger
• Gas Sampling Probe & Hose
• Water Trap with Filter Cartridge
• Magnetic Rubber Holster
• PC Software & USB Cable
• Operating Manual
• Calibration Certificate
• ABS Hard Carrying Case

4500-3 BTU4500 Gas Emissions Analyzer by E Instruments

BTU4500 (2 Gas) for O2, CO, CO2 Included. Upgradeable to Add NO/NOx, NO2, SO2 or CxHy (4-Gas Analyzer) BUILT-IN, NON-THERMAL Printer + Paper Rolls Software Included (save and email reports) (SW KIT) High Range CO Sensor (0-50,000 ppm) Auto Dilution

Accurate / Reliable / Robust / Fast

• Up to FOUR (4) Gas Sensors
• Automatic Data Logging
• Total NOx Capable
• Draft & Differential Pressure
• Dilution Pump for CO Auto-Range Measurements up to 10,000 ppm
• Combustion Efficiency
• PC Software with Bluetooth®

• O2, CO, NO, NO2, SO2, CxHy (HC)
• Built-In Printer Non-Fading Paper
• Full Color Graphic Display
• Field Replaceable Sensors
• PC Software with Bluetooth®
• iOS and Android Mobile Applications

Standard Probe & Hose:

• 12" (300mm) Probe
• 1470 °F (800 °C) max
• 10' (3m) Dual Hose

Long Probe & Hose:

• 30" (750mm) Probe
• 1470 °F (800 °C) max
• 10' (3m) Dual Hose

Long & High Temp Probe & Hose:

• 40" (1m) Probe or 60'' (1.5m) Probe
• 2190 °F (1200 °C) max
• 10' (3m) Hose

Hose Extentions:

• 10' (3m) Length Available

All BTU4500 Kits Include:

• Built-In Printer
• New iOS & Android App (Remote Display & QR Scanning)
• CO2 % Calculation
• Combustion Efficiency, Losses, & Excess Air Calculations
• Draft & Differential Pressure
• Incoming Air Temperature for Condensing Boilers
• Temperature Measurements
• Large Color Display
• 2000 Test Internal Memory
• Bluetooth Connectivity
• Long Lasting Rechargeable Battery & AC Charger
• Gas Sampling Probe & Hose
• Water Trap with Filter Cartridge
• Magnetic Rubber Holster
• PC Software & USB Cable
• Operating Manual
• Calibration Certificate
• ABS Hard Carrying Case

4500-N BTU4500 Gas Emissions Analyzer by E Instruments

BTU4500 (2 Gas) for O2, CO, CO2 Included. Upgradeable to Add NO/NOx, NO2, SO2 or CxHy (4-Gas Analyzer) BUILT-IN, NON-THERMAL Printer + Paper Rolls Software Included (save and email reports) (SW KIT) High Range CO Sensor (0-50,000 ppm) Auto Dilution

Accurate / Reliable / Robust / Fast

• Up to FOUR (4) Gas Sensors
• Automatic Data Logging
• Total NOx Capable
• Draft & Differential Pressure
• Dilution Pump for CO Auto-Range Measurements up to 10,000 ppm
• Combustion Efficiency
• PC Software with Bluetooth®

• O2, CO, NO, NO2, SO2, CxHy (HC)
• Built-In Printer Non-Fading Paper
• Full Color Graphic Display
• Field Replaceable Sensors
• PC Software with Bluetooth®
• iOS and Android Mobile Applications

Standard Probe & Hose:

• 12" (300mm) Probe
• 1470 °F (800 °C) max
• 10' (3m) Dual Hose

Long Probe & Hose:

• 30" (750mm) Probe
• 1470 °F (800 °C) max
• 10' (3m) Dual Hose

Long & High Temp Probe & Hose:

• 40" (1m) Probe or 60'' (1.5m) Probe
• 2190 °F (1200 °C) max
• 10' (3m) Hose

Hose Extentions:

• 10' (3m) Length Available

All BTU4500 Kits Include:

• Built-In Printer
• New iOS & Android App (Remote Display & QR Scanning)
• CO2 % Calculation
• Combustion Efficiency, Losses, & Excess Air Calculations
• Draft & Differential Pressure
• Incoming Air Temperature for Condensing Boilers
• Temperature Measurements
• Large Color Display
• 2000 Test Internal Memory
• Bluetooth Connectivity
• Long Lasting Rechargeable Battery & AC Charger
• Gas Sampling Probe & Hose
• Water Trap with Filter Cartridge
• Magnetic Rubber Holster
• PC Software & USB Cable
• Operating Manual
• Calibration Certificate
• ABS Hard Carrying Case

4500-S BTU4500 Gas Emissions Analyzer by E Instruments

BTU4500 (2 Gas) for O2, CO, CO2 Included. Upgradeable to Add NO/NOx, NO2, SO2 or CxHy (4-Gas Analyzer) BUILT-IN, NON-THERMAL Printer + Paper Rolls Software Included (save and email reports) (SW KIT) High Range CO Sensor (0-50,000 ppm) Auto Dilution

Accurate / Reliable / Robust / Fast

• Up to FOUR (4) Gas Sensors
• Automatic Data Logging
• Total NOx Capable
• Draft & Differential Pressure
• Dilution Pump for CO Auto-Range Measurements up to 10,000 ppm
• Combustion Efficiency
• PC Software with Bluetooth®

• O2, CO, NO, NO2, SO2, CxHy (HC)
• Built-In Printer Non-Fading Paper
• Full Color Graphic Display
• Field Replaceable Sensors
• PC Software with Bluetooth®
• iOS and Android Mobile Applications

Standard Probe & Hose:

• 12" (300mm) Probe
• 1470 °F (800 °C) max
• 10' (3m) Dual Hose

Long Probe & Hose:

• 30" (750mm) Probe
• 1470 °F (800 °C) max
• 10' (3m) Dual Hose

Long & High Temp Probe & Hose:

• 40" (1m) Probe or 60'' (1.5m) Probe
• 2190 °F (1200 °C) max
• 10' (3m) Hose

Hose Extentions:

• 10' (3m) Length Available

All BTU4500 Kits Include:

• Built-In Printer
• New iOS & Android App (Remote Display & QR Scanning)
• CO2 % Calculation
• Combustion Efficiency, Losses, & Excess Air Calculations
• Draft & Differential Pressure
• Incoming Air Temperature for Condensing Boilers
• Temperature Measurements
• Large Color Display
• 2000 Test Internal Memory
• Bluetooth Connectivity
• Long Lasting Rechargeable Battery & AC Charger
• Gas Sampling Probe & Hose
• Water Trap with Filter Cartridge
• Magnetic Rubber Holster
• PC Software & USB Cable
• Operating Manual
• Calibration Certificate
• ABS Hard Carrying Case

27495 Si-CA 030 Gas Analyzer Kit 2AC, two gas sensors (O2, CO), 7" (180mm) Probe, cardboard box packaging by Sauermann

The Si-CA 030 offers everything heating engineers need to inspect and maintain residential and commercial boilers, with wireless connection to our smartphone app and automatic generation of servicing reports and certificates.

• Up to three gas sensors O₂, CO and NO (for NOx)
• CO sensor measurement up to 8,000 ppm
• Auto pump cut-off for high CO levels
• Color display screen
• Lightweight, only 350 g (12 oz)
• Data management with automatic logging & report creation
• Predictive maintenance with estimated sensor life & calibration reminders
• Draft & differential pressure measurements
• Calculated CO₂ % value
• NOx capable with NO sensor
• Quick and easy pump On/Off control
• Combustion efficiency & excess air calculations
• CO safety monitoring in ambient air
• Protective rubber holster
• Extended warranties available

Kit Includes:

• 1 Si-CA 030 analyzer
• 1 O2 gas sensors
• 1 CO gas sensors
• 1 NO gas sensors (optional)
• 1 Protective rubber holster
• 1 Flue gas probe with dual hose
• 1 Water trap with filter
• 1 AC power supply / charger
• 1 USB cable
• 1 Mobile app
• 1 Internal wireless communication module
• 1 Carrying case or box packaging
• 1 Quick Start Guide
• 1 Calibration certificate

27496 Si-CA 030 Gas Analyzer Kit 2AS, two gas sensors (O2, CO), 7" (180mm) Probe, vinyl carrying case by Sauermann

The Si-CA 030 offers everything heating engineers need to inspect and maintain residential and commercial boilers, with wireless connection to our smartphone app and automatic generation of servicing reports and certificates.

• Up to three gas sensors O₂, CO and NO (for NOx)
• CO sensor measurement up to 8,000 ppm
• Auto pump cut-off for high CO levels
• Color display screen
• Lightweight, only 350 g (12 oz)
• Data management with automatic logging & report creation
• Predictive maintenance with estimated sensor life & calibration reminders
• Draft & differential pressure measurements
• Calculated CO₂ % value
• NOx capable with NO sensor
• Quick and easy pump On/Off control
• Combustion efficiency & excess air calculations
• CO safety monitoring in ambient air
• Protective rubber holster
• Extended warranties available

Kit Includes:

• 1 Si-CA 030 analyzer
• 1 O2 gas sensors
• 1 CO gas sensors
• 1 NO gas sensors (optional)
• 1 Protective rubber holster
• 1 Flue gas probe with dual hose
• 1 Water trap with filter
• 1 AC power supply / charger
• 1 USB cable
• 1 Mobile app
• 1 Internal wireless communication module
• 1 Carrying case or box packaging
• 1 Quick Start Guide
• 1 Calibration certificate

27507 Si-CA 130 Gas Analyzer Kit 2AS, two gas sensors (O2, CO), 7" (180mm) Probe, vinyl carrying case by Sauermann

The Si-CA 130 features a touch-screen display and comes with PC-based management software (in addition to the smartphone app) for more in-depth combustion gas analysis. The three field-replaceable cells and sensors offer expanded measurement capability.

• Field replaceable precalibrated sensors
• Large color touch screen
• CO sensor measurement up to 8000 ppm
• Data management with automatic logging & report creation trough app/PC software
• Lightweight, only 350 g (12 oz)
• Up to three gas sensors O₂, CO and NO or Low NO (for NOx)
• Predictive maintenance with estimated sensor life & calibration reminders
• Draft & differential pressure measurements
• Calculated CO₂ % value
• Auto pump cut-off for high CO levels (user-adjustable)
• NOx capable with NO sensor (optional)
• One Touch Pump On/Off with Purge
• PC software with wireless and USB connectivity
• Combustion efficiency & excess air calculations
• Graphical data display
• Customizable gas analysis screen
• Sample conditioning unit for low NOx & high moisture applications
• CO & CO₂ Monitoring in Ambient Air
• Smart Air Temperature Probe
• Protective rubber holster
• Maintenance contracts and extended warranties available

Kit Includes:

• 1 Si-CA 130 analyzer
• 1 O₂ gas sensors
• 1 CO gas sensors
• 1 NO gas sensors
• 1 Low NO gas sensors
• 1 Protective rubber holster
• 1 Flue gas probe with dual hose
• 1 Water trap with filter
• 1 AC power supply / charger
• 1 USB cable
• 1 Mobile app & PC software
• 1 Internal wireless communication module
• 1 Carrying case
• 1 Quick Start Guide
• 1 Calibration certificate

72-2120A-103 Digester Gas Analyzer, with internal LEL alarm shutoff, 1000ppm H2S by RKI Instruments

RKI is proud to introduce our Digester Gas Monitor. Gas from waste digesters contains high levels of methane, CO2, and H2S, with little to no oxygen present. The RKI gas monitor checks for all these gases on a cyclic basis. A powerful air aspirator draws a sample from up to 100 feet away. Since digester gas contains high humidity and high H2S, both of which can cause damage to sampling systems, the RKI Digester Gas Monitor is designed to handle these with no damage to the sampling system or sensors. The sample is passed through a series of dirt, dust, and moisture stopping filters, and these filters are automatically purged with fresh air at the end of each cycle.

Measurement time is just 4 minutes, taken at periodic cycles. Cycle time is selectable, with settings for cycle time of 15 minute, 1 hour, 4 hours, 8 hours, or 24 hours. A cycle can also be initiated anytime by pressing a button. After each cycle, the sensors and sampling system are flushed with fresh air so as to minimize corrosion caused by the high H2S content. The system is fault tolerant minimizing the possibility of expensive repairs or downtime.

System integrity is maintained at all times using a flow fail monitoring device which provides a fail alarm and relay if there is ever a problem with the flow system, such as a blockage, or if the air aspirator compressed air supply is removed or interrupted.

The system is housed in a wall mounting NEMA 4X enclosure. The gas readings can be viewed through the enclosure door clear window. Flow meters and filters are easily visible for confirmation of correct flows and operation. The RKI Digester Gas Monitor contains adjustable alarm levels for each gas, and also programmable alarm relays. In addition, the unit provides 4-20mA signals for each gas concentration for connection to an external DCS, PLC, or other site control system. A Modbus output is also available. The outputs are the readings received from the last cycle taken.

Features:

• Corrosion resistant design; Housing designed for extreme environments; Internal construction for extreme samples; Flow system designed to handle corrosive wet samples
• Sample system designed to handle high humidity
• Accurately measures gases with high levels of H2S present
• 100 ft. sample range
• Up to 4 sensors: Methane 0-100% Volume; CO2 0-50% Volume; Oxygen 0-25% Volume; H2S 0-1000 PPM (0-3000 or 0-5000 optional)
• Self draining moisture trap
• Automatic backflush of sampling system
• Long life air aspirator (no moving parts)
• Suitable for inside/outside installations
• NEMA 4X enclosure
• Uses proven RKI technology
• Modular design easy to maintain
• Simple to operate

Industry Applications:

• Wastewater Treatment Digesters
• Biogas Methane
• Animal Farms

*Please note we can only ship RKI products to customers within the United States

72-2120A-103-3K Digester, Gas Analyzer, with internal LEL alarm shutoff, 3000ppm H2S by RKI Instruments

RKI is proud to introduce our Digester Gas Monitor. Gas from waste digesters contains high levels of methane, CO2, and H2S, with little to no oxygen present. The RKI gas monitor checks for all these gases on a cyclic basis. A powerful air aspirator draws a sample from up to 100 feet away. Since digester gas contains high humidity and high H2S, both of which can cause damage to sampling systems, the RKI Digester Gas Monitor is designed to handle these with no damage to the sampling system or sensors. The sample is passed through a series of dirt, dust, and moisture stopping filters, and these filters are automatically purged with fresh air at the end of each cycle.

Measurement time is just 4 minutes, taken at periodic cycles. Cycle time is selectable, with settings for cycle time of 15 minute, 1 hour, 4 hours, 8 hours, or 24 hours. A cycle can also be initiated anytime by pressing a button. After each cycle, the sensors and sampling system are flushed with fresh air so as to minimize corrosion caused by the high H2S content. The system is fault tolerant minimizing the possibility of expensive repairs or downtime.

System integrity is maintained at all times using a flow fail monitoring device which provides a fail alarm and relay if there is ever a problem with the flow system, such as a blockage, or if the air aspirator compressed air supply is removed or interrupted.

The system is housed in a wall mounting NEMA 4X enclosure. The gas readings can be viewed through the enclosure door clear window. Flow meters and filters are easily visible for confirmation of correct flows and operation. The RKI Digester Gas Monitor contains adjustable alarm levels for each gas, and also programmable alarm relays. In addition, the unit provides 4-20mA signals for each gas concentration for connection to an external DCS, PLC, or other site control system. A Modbus output is also available. The outputs are the readings received from the last cycle taken.

Features:

• Corrosion resistant design; Housing designed for extreme environments; Internal construction for extreme samples; Flow system designed to handle corrosive wet samples
• Sample system designed to handle high humidity
• Accurately measures gases with high levels of H2S present
• 100 ft. sample range
• Up to 4 sensors: Methane 0-100% Volume; CO2 0-50% Volume; Oxygen 0-25% Volume; H2S 0-1000 PPM (0-3000 or 0-5000 optional)
• Self draining moisture trap
• Automatic backflush of sampling system
• Long life air aspirator (no moving parts)
• Suitable for inside/outside installations
• NEMA 4X enclosure
• Uses proven RKI technology
• Modular design easy to maintain
• Simple to operate

Industry Applications:

• Wastewater Treatment Digesters
• Biogas Methane
• Animal Farms

*Please note we can only ship RKI products to customers within the United States

72-2120A-103-5K Digester, Gas Analyzer, with internal LEL alarm shutoff, 5000ppm H2S by RKI Instruments

RKI is proud to introduce our Digester Gas Monitor. Gas from waste digesters contains high levels of methane, CO2, and H2S, with little to no oxygen present. The RKI gas monitor checks for all these gases on a cyclic basis. A powerful air aspirator draws a sample from up to 100 feet away. Since digester gas contains high humidity and high H2S, both of which can cause damage to sampling systems, the RKI Digester Gas Monitor is designed to handle these with no damage to the sampling system or sensors. The sample is passed through a series of dirt, dust, and moisture stopping filters, and these filters are automatically purged with fresh air at the end of each cycle.

Measurement time is just 4 minutes, taken at periodic cycles. Cycle time is selectable, with settings for cycle time of 15 minute, 1 hour, 4 hours, 8 hours, or 24 hours. A cycle can also be initiated anytime by pressing a button. After each cycle, the sensors and sampling system are flushed with fresh air so as to minimize corrosion caused by the high H2S content. The system is fault tolerant minimizing the possibility of expensive repairs or downtime.

System integrity is maintained at all times using a flow fail monitoring device which provides a fail alarm and relay if there is ever a problem with the flow system, such as a blockage, or if the air aspirator compressed air supply is removed or interrupted.

The system is housed in a wall mounting NEMA 4X enclosure. The gas readings can be viewed through the enclosure door clear window. Flow meters and filters are easily visible for confirmation of correct flows and operation. The RKI Digester Gas Monitor contains adjustable alarm levels for each gas, and also programmable alarm relays. In addition, the unit provides 4-20mA signals for each gas concentration for connection to an external DCS, PLC, or other site control system. A Modbus output is also available. The outputs are the readings received from the last cycle taken.

Features:

• Corrosion resistant design; Housing designed for extreme environments; Internal construction for extreme samples; Flow system designed to handle corrosive wet samples
• Sample system designed to handle high humidity
• Accurately measures gases with high levels of H2S present
• 100 ft. sample range
• Up to 4 sensors: Methane 0-100% Volume; CO2 0-50% Volume; Oxygen 0-25% Volume; H2S 0-1000 PPM (0-3000 or 0-5000 optional)
• Self draining moisture trap
• Automatic backflush of sampling system
• Long life air aspirator (no moving parts)
• Suitable for inside/outside installations
• NEMA 4X enclosure
• Uses proven RKI technology
• Modular design easy to maintain
• Simple to operate

Industry Applications:

• Wastewater Treatment Digesters
• Biogas Methane
• Animal Farms

*Please note we can only ship RKI products to customers within the United States

72-2120A-201 Digester Gas Analyzer, with internal LEL alarm shutoff, 100%vol CH4/25%vol O2 by RKI Instruments

RKI is proud to introduce our Digester Gas Monitor. Gas from waste digesters contains high levels of methane, CO2, and H2S, with little to no oxygen present. The RKI gas monitor checks for all these gases on a cyclic basis. A powerful air aspirator draws a sample from up to 100 feet away. Since digester gas contains high humidity and high H2S, both of which can cause damage to sampling systems, the RKI Digester Gas Monitor is designed to handle these with no damage to the sampling system or sensors. The sample is passed through a series of dirt, dust, and moisture stopping filters, and these filters are automatically purged with fresh air at the end of each cycle.

Measurement time is just 4 minutes, taken at periodic cycles. Cycle time is selectable, with settings for cycle time of 15 minute, 1 hour, 4 hours, 8 hours, or 24 hours. A cycle can also be initiated anytime by pressing a button. After each cycle, the sensors and sampling system are flushed with fresh air so as to minimize corrosion caused by the high H2S content. The system is fault tolerant minimizing the possibility of expensive repairs or downtime.

System integrity is maintained at all times using a flow fail monitoring device which provides a fail alarm and relay if there is ever a problem with the flow system, such as a blockage, or if the air aspirator compressed air supply is removed or interrupted.

The system is housed in a wall mounting NEMA 4X enclosure. The gas readings can be viewed through the enclosure door clear window. Flow meters and filters are easily visible for confirmation of correct flows and operation. The RKI Digester Gas Monitor contains adjustable alarm levels for each gas, and also programmable alarm relays. In addition, the unit provides 4-20mA signals for each gas concentration for connection to an external DCS, PLC, or other site control system. A Modbus output is also available. The outputs are the readings received from the last cycle taken.

Features:

• Corrosion resistant design; Housing designed for extreme environments; Internal construction for extreme samples; Flow system designed to handle corrosive wet samples
• Sample system designed to handle high humidity
• Accurately measures gases with high levels of H2S present
• 100 ft. sample range
• Up to 4 sensors: Methane 0-100% Volume; CO2 0-50% Volume; Oxygen 0-25% Volume; H2S 0-1000 PPM (0-3000 or 0-5000 optional)
• Self draining moisture trap
• Automatic backflush of sampling system
• Long life air aspirator (no moving parts)
• Suitable for inside/outside installations
• NEMA 4X enclosure
• Uses proven RKI technology
• Modular design easy to maintain
• Simple to operate

Industry Applications:

• Wastewater Treatment Digesters
• Biogas Methane
• Animal Farms

*Please note we can only ship RKI products to customers within the United States

72-2120A-202 Digester Gas Analyzer, with internal LEL alarm shutoff, 100%vol CH4/1000ppm H2S by RKI Instruments

RKI is proud to introduce our Digester Gas Monitor. Gas from waste digesters contains high levels of methane, CO2, and H2S, with little to no oxygen present. The RKI gas monitor checks for all these gases on a cyclic basis. A powerful air aspirator draws a sample from up to 100 feet away. Since digester gas contains high humidity and high H2S, both of which can cause damage to sampling systems, the RKI Digester Gas Monitor is designed to handle these with no damage to the sampling system or sensors. The sample is passed through a series of dirt, dust, and moisture stopping filters, and these filters are automatically purged with fresh air at the end of each cycle.

Measurement time is just 4 minutes, taken at periodic cycles. Cycle time is selectable, with settings for cycle time of 15 minute, 1 hour, 4 hours, 8 hours, or 24 hours. A cycle can also be initiated anytime by pressing a button. After each cycle, the sensors and sampling system are flushed with fresh air so as to minimize corrosion caused by the high H2S content. The system is fault tolerant minimizing the possibility of expensive repairs or downtime.

System integrity is maintained at all times using a flow fail monitoring device which provides a fail alarm and relay if there is ever a problem with the flow system, such as a blockage, or if the air aspirator compressed air supply is removed or interrupted.

The system is housed in a wall mounting NEMA 4X enclosure. The gas readings can be viewed through the enclosure door clear window. Flow meters and filters are easily visible for confirmation of correct flows and operation. The RKI Digester Gas Monitor contains adjustable alarm levels for each gas, and also programmable alarm relays. In addition, the unit provides 4-20mA signals for each gas concentration for connection to an external DCS, PLC, or other site control system. A Modbus output is also available. The outputs are the readings received from the last cycle taken.

Features:

• Corrosion resistant design; Housing designed for extreme environments; Internal construction for extreme samples; Flow system designed to handle corrosive wet samples
• Sample system designed to handle high humidity
• Accurately measures gases with high levels of H2S present
• 100 ft. sample range
• Up to 4 sensors: Methane 0-100% Volume; CO2 0-50% Volume; Oxygen 0-25% Volume; H2S 0-1000 PPM (0-3000 or 0-5000 optional)
• Self draining moisture trap
• Automatic backflush of sampling system
• Long life air aspirator (no moving parts)
• Suitable for inside/outside installations
• NEMA 4X enclosure
• Uses proven RKI technology
• Modular design easy to maintain
• Simple to operate

Industry Applications:

• Wastewater Treatment Digesters
• Biogas Methane
• Animal Farms

*Please note we can only ship RKI products to customers within the United States

72-2120A-202-3K Digester, Gas Analyzer, with internal LEL alarm shutoff, 100%vol CH4/3000ppm H2S by RKI Instruments

RKI is proud to introduce our Digester Gas Monitor. Gas from waste digesters contains high levels of methane, CO2, and H2S, with little to no oxygen present. The RKI gas monitor checks for all these gases on a cyclic basis. A powerful air aspirator draws a sample from up to 100 feet away. Since digester gas contains high humidity and high H2S, both of which can cause damage to sampling systems, the RKI Digester Gas Monitor is designed to handle these with no damage to the sampling system or sensors. The sample is passed through a series of dirt, dust, and moisture stopping filters, and these filters are automatically purged with fresh air at the end of each cycle.

Measurement time is just 4 minutes, taken at periodic cycles. Cycle time is selectable, with settings for cycle time of 15 minute, 1 hour, 4 hours, 8 hours, or 24 hours. A cycle can also be initiated anytime by pressing a button. After each cycle, the sensors and sampling system are flushed with fresh air so as to minimize corrosion caused by the high H2S content. The system is fault tolerant minimizing the possibility of expensive repairs or downtime.

System integrity is maintained at all times using a flow fail monitoring device which provides a fail alarm and relay if there is ever a problem with the flow system, such as a blockage, or if the air aspirator compressed air supply is removed or interrupted.

The system is housed in a wall mounting NEMA 4X enclosure. The gas readings can be viewed through the enclosure door clear window. Flow meters and filters are easily visible for confirmation of correct flows and operation. The RKI Digester Gas Monitor contains adjustable alarm levels for each gas, and also programmable alarm relays. In addition, the unit provides 4-20mA signals for each gas concentration for connection to an external DCS, PLC, or other site control system. A Modbus output is also available. The outputs are the readings received from the last cycle taken.

Features:

• Corrosion resistant design; Housing designed for extreme environments; Internal construction for extreme samples; Flow system designed to handle corrosive wet samples
• Sample system designed to handle high humidity
• Accurately measures gases with high levels of H2S present
• 100 ft. sample range
• Up to 4 sensors: Methane 0-100% Volume; CO2 0-50% Volume; Oxygen 0-25% Volume; H2S 0-1000 PPM (0-3000 or 0-5000 optional)
• Self draining moisture trap
• Automatic backflush of sampling system
• Long life air aspirator (no moving parts)
• Suitable for inside/outside installations
• NEMA 4X enclosure
• Uses proven RKI technology
• Modular design easy to maintain
• Simple to operate

Industry Applications:

• Wastewater Treatment Digesters
• Biogas Methane
• Animal Farms

*Please note we can only ship RKI products to customers within the United States

72-2120A-204 Digester Gas Analyzer, with internal LEL alarm shutoff, 25% volume O2/1000ppm H2S by RKI Instruments

RKI is proud to introduce our Digester Gas Monitor. Gas from waste digesters contains high levels of methane, CO2, and H2S, with little to no oxygen present. The RKI gas monitor checks for all these gases on a cyclic basis. A powerful air aspirator draws a sample from up to 100 feet away. Since digester gas contains high humidity and high H2S, both of which can cause damage to sampling systems, the RKI Digester Gas Monitor is designed to handle these with no damage to the sampling system or sensors. The sample is passed through a series of dirt, dust, and moisture stopping filters, and these filters are automatically purged with fresh air at the end of each cycle.

Measurement time is just 4 minutes, taken at periodic cycles. Cycle time is selectable, with settings for cycle time of 15 minute, 1 hour, 4 hours, 8 hours, or 24 hours. A cycle can also be initiated anytime by pressing a button. After each cycle, the sensors and sampling system are flushed with fresh air so as to minimize corrosion caused by the high H2S content. The system is fault tolerant minimizing the possibility of expensive repairs or downtime.

System integrity is maintained at all times using a flow fail monitoring device which provides a fail alarm and relay if there is ever a problem with the flow system, such as a blockage, or if the air aspirator compressed air supply is removed or interrupted.

The system is housed in a wall mounting NEMA 4X enclosure. The gas readings can be viewed through the enclosure door clear window. Flow meters and filters are easily visible for confirmation of correct flows and operation. The RKI Digester Gas Monitor contains adjustable alarm levels for each gas, and also programmable alarm relays. In addition, the unit provides 4-20mA signals for each gas concentration for connection to an external DCS, PLC, or other site control system. A Modbus output is also available. The outputs are the readings received from the last cycle taken.

Features:

• Corrosion resistant design; Housing designed for extreme environments; Internal construction for extreme samples; Flow system designed to handle corrosive wet samples
• Sample system designed to handle high humidity
• Accurately measures gases with high levels of H2S present
• 100 ft. sample range
• Up to 4 sensors: Methane 0-100% Volume; CO2 0-50% Volume; Oxygen 0-25% Volume; H2S 0-1000 PPM (0-3000 or 0-5000 optional)
• Self draining moisture trap
• Automatic backflush of sampling system
• Long life air aspirator (no moving parts)
• Suitable for inside/outside installations
• NEMA 4X enclosure
• Uses proven RKI technology
• Modular design easy to maintain
• Simple to operate

Industry Applications:

• Wastewater Treatment Digesters
• Biogas Methane
• Animal Farms

*Please note we can only ship RKI products to customers within the United States

72-2120A-301 Digester Gas Analyzer, with internal LEL alarm shutoff, 100%vol CH4/25%vol O2/1000ppm H2S by RKI Instruments

RKI is proud to introduce our Digester Gas Monitor. Gas from waste digesters contains high levels of methane, CO2, and H2S, with little to no oxygen present. The RKI gas monitor checks for all these gases on a cyclic basis. A powerful air aspirator draws a sample from up to 100 feet away. Since digester gas contains high humidity and high H2S, both of which can cause damage to sampling systems, the RKI Digester Gas Monitor is designed to handle these with no damage to the sampling system or sensors. The sample is passed through a series of dirt, dust, and moisture stopping filters, and these filters are automatically purged with fresh air at the end of each cycle.

Measurement time is just 4 minutes, taken at periodic cycles. Cycle time is selectable, with settings for cycle time of 15 minute, 1 hour, 4 hours, 8 hours, or 24 hours. A cycle can also be initiated anytime by pressing a button. After each cycle, the sensors and sampling system are flushed with fresh air so as to minimize corrosion caused by the high H2S content. The system is fault tolerant minimizing the possibility of expensive repairs or downtime.

System integrity is maintained at all times using a flow fail monitoring device which provides a fail alarm and relay if there is ever a problem with the flow system, such as a blockage, or if the air aspirator compressed air supply is removed or interrupted.

The system is housed in a wall mounting NEMA 4X enclosure. The gas readings can be viewed through the enclosure door clear window. Flow meters and filters are easily visible for confirmation of correct flows and operation. The RKI Digester Gas Monitor contains adjustable alarm levels for each gas, and also programmable alarm relays. In addition, the unit provides 4-20mA signals for each gas concentration for connection to an external DCS, PLC, or other site control system. A Modbus output is also available. The outputs are the readings received from the last cycle taken.

Features:

• Corrosion resistant design; Housing designed for extreme environments; Internal construction for extreme samples; Flow system designed to handle corrosive wet samples
• Sample system designed to handle high humidity
• Accurately measures gases with high levels of H2S present
• 100 ft. sample range
• Up to 4 sensors: Methane 0-100% Volume; CO2 0-50% Volume; Oxygen 0-25% Volume; H2S 0-1000 PPM (0-3000 or 0-5000 optional)
• Self draining moisture trap
• Automatic backflush of sampling system
• Long life air aspirator (no moving parts)
• Suitable for inside/outside installations
• NEMA 4X enclosure
• Uses proven RKI technology
• Modular design easy to maintain
• Simple to operate

Industry Applications:

• Wastewater Treatment Digesters
• Biogas Methane
• Animal Farms

*Please note we can only ship RKI products to customers within the United States