RKI Instruments

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

FP-300 Paper Tape Machine by RKI Instruments

RKI s paper tape monitors utilize highly sensitive colorimetric tapes to achieve interference free detection at low PPB and PPM levels Ammonia, Arsine, Chlorine, Diborane, Hydrogen Chloride, Hydrogen Fluoride, Hydrogen Sulfide, Phosphine, Silane. The FP-300 is equipped with an easily replaceable tape. This model is equipped with a digital display showing the type of gas and concentration in PPM or PPB. The FP-300 will also display remaining tape life as well as an end of tape alarm.

The FP-300 has audible and visual alarms, as well as alarm relay contacts and 4-20mA output. A unique tape saver mode extends tape life in applications where high background gas levels may be present.

The FP-300 meets and exceeds OSHA and NIOSH compliance requirements, and does not respond to interfering gases (hydrocarbons, alcohols, solvents, CO, etc.) that may be present in industrial/manufacturing environments.

Features:

• Small and compact
• Highly sensitive and ideal for low gas concentrations (ppb detection)
• Interference-free detection
• Easy detection tape replacement with plug-in cassette
• Tape remainder display and tape end warning alarm provided
• Easily transportable

Applications:

• Scrubbers
• Environmental Monitoring
• Semiconductor Fabs
• Manufacturing
• Detecting uncaptured gas from scrubber

*Please note we can only ship RKI products to customers within the United States

65-2424RK M-Series Hydrogen Sulfide (H2S) Sensor/Transmitter in Plastic Enclosure (Not Explosion Proof) by RKI Instruments

Some gas monitoring requirements are basic but important. The RKI M-Series transmitter is a highly reliable and very cost-effective 4-20 mA transmitter for the detection of carbon monoxide and hydrogen sulfide. This transmitter operates from a 24 VDC (11 VDC to 30 VDC) power source and provides a 4 20 mA output signal, which can be connected to a wide variety of RKI or third party controllers. The M-Series transmitters are built for use in either indoor or semienclosed areas.

The electronics are protected inside a plastic enclosure to avoid damage from mechanical abuse, water, dust or corrosion. Sensors for the M-Series have a long life-span that typically last two to three years.

Field calibrations are very basic and can be completed by a single person. The zero and calibration functions for the MSeries are performed by simply adjusting potentiometers on the amplifier board. The amplifier board is equipped with easily accessible test jacks for the connection of a voltmeter. The voltmeter is used to view sensor response while the calibration gas is being applied and the potentiometers are adjusted with a screwdriver.

Features

• Water/dust resistant housing
• Available for CO and H2S
• Long life sensors (2 + years typical)
• Competitively priced
• Compact design

Applications

• Water & wastewater treatment plants
• Pulp & paper mills
• Gas, telephone & electric utilities
• Parking garages
• Manufacturing facilities
• Loading docks

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

61-0198RK-10 Sensor, IR Carbon Dioxide (CO2) 0-100%, Non Explosion Proof Direct Connect, Replaceable Sensor by RKI Instruments

The RKI Direct Connect series gas sensors are highly reliable and very cost effective for the detection of common gas hazards. The direct connect series are available for LEL, H2 Specific LEL, LEL IR, Oxygen, H2S, CO, CO2, and for a variety of toxic gases. The sensors for LEL, H2, Oxygen, H2S, CO2, and Carbon Monoxide are explosion-proof with flame arrestors, and approved for use in hazardous areas (Class 1, Div. 1 Groups B, C, D). An optional non-explosion proof version is available for oxygen, H2S, CO, and CO2 for use in non-hazardous atmospheres.

The Direct Connect sensors can be used in two different ways. The sensors can be mounted directly to the controllers as a complete stand alone system, or they can be mounted to explosion proof junction boxes for remote detection.

The toxic sensors are electrochemical type plug-in sensors, which provide high specificity, fast response, and long life. The plug-in design allows quick replacement in the field with no tools required. Toxic sensors are designed for use in Class I, Div. 2 hazardous locations. Sensors are available for NH3, SO2, PH3, AsH3, and HCN.

The Direct Connect sensors can be used either indoors or outdoors. The flame arrestors for the explosion-proof versions utilize a patented coating which make them water repellent. Also, splash guards are available for use in very wet environments. An optional stainless steel junction box is available for corrosive environments.

All of the Direct Connect sensors are designed to specifically interface with RKI Beacon 110, 200, and 410 controllers.

Features:

• Available gases include; LEL, H2S, CO, & CO2; Toxic sensors include NH3, AsH3, HCN, PH3, and SO2
• Infrared sensor for combustibles and CO2
• Patented water repellent sensor coating
• Explosion proof construction
• Optional stainless steel junction box

Applications:

• Petrochemical plants
• Refineries
• Gas plants
• Offshore drilling platforms
• Water & wastewater treatment plants
• Pulp & paper mills
• Gas, telephone, & electric utilities
• Parking garages
• Manufacturing facilities
• Steel
• Automotive

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

73-0050RK-HCN SC-01 Single Toxic Gas Monitor, Hydrogen Cyanide (HCN), 0 - 15.0 ppm, with Alligator Clip by RKI Instruments

Paving the way for gas detection and monitoring solutions, RKI Instruments produces the most advanced sensors and monitors. Their teams of experts are constantly seeking new and innovative methods for meeting the unique needs of jobsites with potentially hazardous conditions. Integrating the latest smart sensor technology with functional design, RKI Instruments is proud to present the SC-01 Model for single toxic gas monitoring.

SC-01 Model Single Toxic Gas Monitor

The SC-01 Single Toxic Gas Monitor is the latest in smart sensor technology with practical applications in refineries, chemical plants, hazmat response, semiconductor plants, and more. It is a versatile single gas detector with interchangeable sensors. The unit automatically recognizes when a sensor has been changed and automatically calibrates to the recognized sensor. The internal technology stores each sensor's configuration and activates the data once the new sensor is recognized.

What sets the SC-01 apart from its competitors is its wide range of available ESM-01 sensors including unique sensors for arsine, ammonia, carbon monoxide, chlorine, hydrogen cyanide, hydrogen sulfide, phosphine, and sulfur dioxide. These plug in style sensors are easy to change and can be replaced quickly while onsite. Onsite workers can also utilize the optional 10 foot extender cable for remote monitoring and quick response.

Exclusive Features

The SC-01's large backlit LCD display is great for onsite use and is easy to read. The screen displays the gas reading, battery level, and current time. When the alarm is activated, the LCD screen's backlight automatically activates. The alarm features a quadruple notification system that includes a buzzing audible alarm, a blinking LED display, a vibration alert, and display indicator. The unit performs regular safety self-evaluations for sensor connections, battery life, and circuit issues. Amazingly, the unit can function with more than 250 hours of continuous operation with 2 AA alkaline batteries. The SC-01 comes standard with data logging capabilities ensuring that workplace safety managers are able to monitor, record, and evaluate possible hazard trends.

SC-01 Model Specifications

The unit is highly portable with its lightweight (less than 8 ounces) and pocket size dimensions (2.6 x 6.2 x 1.2 ). Users can easily control the unit's functioning with its 3 large front facing push buttons. The casing is designed to protect the monitor with its high impact plastic with rubber boot that is dust proof and splash proof. The typical response time for gas detection is approximately 60 seconds and uses electrochemical detection. For gas monitoring needs, the SC-01 Model is rated intrinsically safe.

The SC-01 Single Toxic Gas Monitor comes standard with several accessories for easy use including an alligator clip, AA alkaline batteries, impact resistant rubber boot, and a user manual. Users can also purchase optional accessories to further customize the unit to meet specific workplace needs. These optional accessories include a belt clip, a 10 foot extender cable, and datalogging software that is PC compatible.

*Please note we can only ship RKI products to customers within the United States

65-2631RK-03 M2, IR Carbon Dioxide (CO2) 0 - 5%, Sensor/Transmitter, Non Explosion Proof with J-Box by RKI Instruments

RKI Instruments uses the latest cutting edge technology when developing transmitters and sensors. Its dedication to workplace safety and reliable safety solutions is unparalleled. The M2 Stand Alone Transmitter utilizes state of the art sensor cell technology to integrate workplace safety with the industry's more advanced transmitter technologies.

M2 Stand Alone Transmitter

The M2 Stand Alone Transmitter is operational with or without a controller and is available in two forms: explosion proof and non-explosion proof. The unit has a backlit screen for a direct digital readout, and a user friendly setup with push buttons and easy to read LCD menus. The advanced technology transmitter can function as an independent standalone system or as part of an integrated detection and transmission system. Using state of the art technology, the transmitter uses a magnetic want technique for performing non-intrusive calibration. For optimal stability and accurate readings, the unit provides an automatic zero drift correction feature. This also reduces the need for adjustments due to sensor aging.

The M2 Stand Alone Transmitter is available for LEL, H2S, CO, PPM, HC, CO2, CI2, NH3, SO2, HCN, and more. The unit also features an infrared sensor for CO2 and combustible gases. With 2 fully programmable alarms and a fail relay, the visual color coded LED alarms are reliable and customizable to meet specific needs.

Advanced sensor technology

The state of the art sensors are long lasting with a lifespan typically over two years. Sensor construction is rated Class I, Division 1 groups B, C, and D for flammables, CO, H2S, O2, and CO2. The sensors are rated Class I, Division 2 for all other toxic gases. Depending on the gas, the sensors will operate through a catalytic, galvanic cell, electrochemical, or infrared design. The plug in nature of the sensors allows for a quick and tool free onsite replacement.

Specifications

Each transmitter features 2 to 3 years of life with normal service. The explosion proof LEL H2 specific transmitter has 3 to 5 years with normal service, and the explosion proof carbon dioxide, methane, and hydrocarbons feature over 5 years of life with normal service. The explosion proof transmitters are also water repellant. Each device is approximately 8.5 H x 5.2 W x 4.5 D and features an alphanumeric display with a backlight. The screen displays 8 characters per line with 2 lines for gas concentration readouts.

Optional Accessories

The M2 Stand Alone Transmitter has a variety of optional accessories available including calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors or panels, and dataloggers. The transmitters are directly compatible with Beacon 110, 200, 410, and 800 controllers.

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

72-2120-201 Digester Gas Monitor, 100% Volume CH4/25% Volume O2 by RKI Instruments

RKI is proud to introduce our Digester Gas Monitor. Gas from waste digesters contains high levels of methane, CO2, and H2S, with little to no oxygen present. The RKI gas monitor checks for all these gases on a cyclic basis. A powerful air aspirator draws a sample from up to 100 feet away. Since digester gas contains high humidity and high H2S, both of which can cause damage to sampling systems, the RKI Digester Gas Monitor is designed to handle these with no damage to the sampling system or sensors. The sample is passed through a series of dirt, dust, and moisture stopping filters, and these filters are automatically purged with fresh air at the end of each cycle.

Measurement time is just 4 minutes, taken at periodic cycles. Cycle time is selectable, with settings for cycle time of 15 minute, 1 hour, 4 hours, 8 hours, or 24 hours. A cycle can also be initiated anytime by pressing a button. After each cycle, the sensors and sampling system are flushed with fresh air so as to minimize corrosion caused by the high H2S content. The system is fault tolerant minimizing the possibility of expensive repairs or downtime.

System integrity is maintained at all times using a flow fail monitoring device which provides a fail alarm and relay if there is ever a problem with the flow system, such as a blockage, or if the air aspirator compressed air supply is removed or interrupted.

The system is housed in a wall mounting NEMA 4X enclosure. The gas readings can be viewed through the enclosure door clear window. Flow meters and filters are easily visible for confirmation of correct flows and operation. The RKI Digester Gas Monitor contains adjustable alarm levels for each gas, and also programmable alarm relays. In addition, the unit provides 4-20mA signals for each gas concentration for connection to an external DCS, PLC, or other site control system. A Modbus output is also available. The outputs are the readings received from the last cycle taken.

Features:

• Corrosion resistant design; Housing designed for extreme environments; Internal construction for extreme samples; Flow system designed to handle corrosive wet samples
• Sample system designed to handle high humidity
• Accurately measures gases with high levels of H2S present
• 100 ft. sample range
• Up to 4 sensors: Methane 0-100% Volume; CO2 0-50% Volume; Oxygen 0-25% Volume; H2S 0-1000 PPM (0-3000 or 0-5000 optional)
• Self draining moisture trap
• Automatic backflush of sampling system
• Long life air aspirator (no moving parts)
• Suitable for inside/outside installations
• NEMA 4X enclosure
• Uses proven RKI technology
• Modular design easy to maintain
• Simple to operate

Industry Applications:

• Wastewater Treatment Digesters
• Biogas Methane
• Animal Farms

*Please note we can only ship RKI products to customers within the United States

72-5539RK Eagle Portable Monitor for LEL & PPM/O2/CO/CI2/SiH4 by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

725-128-02-P2 Eagle 2 Portable Monitor for LEL & PPM/O2/CO2 10,000 ppm Volume (IR)/VOC?s 0 - 2,000 ppm, (PID)/NH3 by RKI Instruments

Continuing in its legacy of durable and reliable gas detection and monitoring systems, RKI Instruments is proud to offer a new product in its popular Eagle portable gas detector series. The Eagle 2 can monitor up to 6 different gases and is equipped with several exclusive features that can only be found with the Eagle series. In addition, its large glove friendly push buttons and LCD screen ensure an ease of use when onsite. Rated intrinsically safe, the Eagle 2 is equipped with state of the art technologies that are not available with other competitive gas detectors and monitors.

Specialty Sensors

The Eagle 2 has a variety of available specialty sensors. Workers can use a photoionization detector for low or high range VOC detection and Fence Electrode Technology for humidity and contamination resistance. An infrared sensor is available for Co2, % LEL CH4, % Volume CH4, % LEL HC, and % Volume HC. Thermal conductivity sensors are available for % Volume H2 and % Volume CH4. The unit is also compatible with the smart plug and play toxic sensors for the detection of NH3, AsH3, CI2, HCN, PH3, and SO2. With the wide variety of sensors and gas detection available, the Eagle 2 can be customized to meet almost all worksite gas detection needs.

Exclusive Features

The monitor has a long internal pump that can draw samples for up to 125 feet. The pump features a low flow auto shut off and alarm. This allows operators to respond swiftly from a safe distance. The unit is multilingual with 5 different language preferences, and features an alkaline battery life of 18 hours or a NiMH life of 20 hours. To protect the integrity of the device and the configurations, the unit can be password protected. The Eagle 2 also has standard data logging capabilities for easy research, evaluation, and site monitoring. To reduce calibration costs and time, the unit features an automatic calibration option and a single gas calibration option.

The Eagle 2 is heavily protected from environmental conditions by a weather proof, chemical resistant RFI/EMI coated high impact polycarbonate/PBT blend enclosure. The enclosure also renders the unit water and dust resistant. Because of the enclosure, the Eagle 2 can function in 2 inches of water without leakage.

Eagle 2 Specifications

The portable and durable unit is lightweight at less than 4 pounds. Its dimensions are suitable for convenient carrying (9.5?L x 5.25?W x 5.875?H), and it features a conveniently placed durable top handle. The large easy to read display has a polyurethane overlay backlights on demand and when the alarm is activated. The 2 alarm channels are fully adjustable for the user and can be password protected. With a 95 dB buzzer and 4 high intensity LEDs, the alarm is sure not to be missed. The Eagle 2 is standard with a 2 year warranty for material and workmanship and a 1 year warranty for PID sensor.

*Please note we can only ship RKI products to customers within the United States

73-0051RK-HCN SC-01 Single Toxic Gas Monitor, Hydrogen Cyanide (HCN), 0 - 15.0 ppm, with Belt Clip by RKI Instruments

Paving the way for gas detection and monitoring solutions, RKI Instruments produces the most advanced sensors and monitors. Their teams of experts are constantly seeking new and innovative methods for meeting the unique needs of jobsites with potentially hazardous conditions. Integrating the latest smart sensor technology with functional design, RKI Instruments is proud to present the SC-01 Model for single toxic gas monitoring.

SC-01 Model Single Toxic Gas Monitor

The SC-01 Single Toxic Gas Monitor is the latest in smart sensor technology with practical applications in refineries, chemical plants, hazmat response, semiconductor plants, and more. It is a versatile single gas detector with interchangeable sensors. The unit automatically recognizes when a sensor has been changed and automatically calibrates to the recognized sensor. The internal technology stores each sensor's configuration and activates the data once the new sensor is recognized.

What sets the SC-01 apart from its competitors is its wide range of available ESM-01 sensors including unique sensors for arsine, ammonia, carbon monoxide, chlorine, hydrogen cyanide, hydrogen sulfide, phosphine, and sulfur dioxide. These plug in style sensors are easy to change and can be replaced quickly while onsite. Onsite workers can also utilize the optional 10 foot extender cable for remote monitoring and quick response.

Exclusive Features

The SC-01's large backlit LCD display is great for onsite use and is easy to read. The screen displays the gas reading, battery level, and current time. When the alarm is activated, the LCD screen's backlight automatically activates. The alarm features a quadruple notification system that includes a buzzing audible alarm, a blinking LED display, a vibration alert, and display indicator. The unit performs regular safety self-evaluations for sensor connections, battery life, and circuit issues. Amazingly, the unit can function with more than 250 hours of continuous operation with 2 AA alkaline batteries. The SC-01 comes standard with data logging capabilities ensuring that workplace safety managers are able to monitor, record, and evaluate possible hazard trends.

SC-01 Model Specifications

The unit is highly portable with its lightweight (less than 8 ounces) and pocket size dimensions (2.6 x 6.2 x 1.2 ). Users can easily control the unit's functioning with its 3 large front facing push buttons. The casing is designed to protect the monitor with its high impact plastic with rubber boot that is dust proof and splash proof. The typical response time for gas detection is approximately 60 seconds and uses electrochemical detection. For gas monitoring needs, the SC-01 Model is rated intrinsically safe.

The SC-01 Single Toxic Gas Monitor comes standard with several accessories for easy use including an alligator clip, AA alkaline batteries, impact resistant rubber boot, and a user manual. Users can also purchase optional accessories to further customize the unit to meet specific workplace needs. These optional accessories include a belt clip, a 10 foot extender cable, and datalogging software that is PC compatible.

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

FP-300A-BF3 FP-300 Paper Tape Machine for Boron Trifluoride, 0 - 3 ppm by RKI Instruments

RKI s paper tape monitors utilize highly sensitive colorimetric tapes to achieve interference free detection at low PPB and PPM levels Ammonia, Arsine, Chlorine, Diborane, Hydrogen Chloride, Hydrogen Fluoride, Hydrogen Sulfide, Phosphine, Silane. The FP-300 is equipped with an easily replaceable tape. This model is equipped with a digital display showing the type of gas and concentration in PPM or PPB. The FP-300 will also display remaining tape life as well as an end of tape alarm.

The FP-300 has audible and visual alarms, as well as alarm relay contacts and 4-20mA output. A unique tape saver mode extends tape life in applications where high background gas levels may be present.

The FP-300 meets and exceeds OSHA and NIOSH compliance requirements, and does not respond to interfering gases (hydrocarbons, alcohols, solvents, CO, etc.) that may be present in industrial/manufacturing environments.

Features:

• Small and compact
• Highly sensitive and ideal for low gas concentrations (ppb detection)
• Interference-free detection
• Easy detection tape replacement with plug-in cassette
• Tape remainder display and tape end warning alarm provided
• Easily transportable

Applications:

• Scrubbers
• Environmental Monitoring
• Semiconductor Fabs
• Manufacturing
• Detecting uncaptured gas from scrubber

*Please note we can only ship RKI products to customers within the United States