Milwaukee

MA9315 Electrode Holder for Bench Meters by Milwaukee

The MA9315 is a high quality electrode holder to be used with Milwaukee bench meters.

MA955 CO2 Gas On/Off Inline Solenoid Valve with 4' Cord 110 Volt Only Includes Fittings by Milwaukee

The solenoid valve is an accessory for the MC122 and the MC125 to automate your dosing of CO2 and makes sure that the plants of your aquarium are always healthy.

MA955, solenoid valve, is supplied with 1.5 m cable.

CO2 Solenoid Diaphram Valve by Milwaukee

Includes flow regulator, needle valve, electronic solenoid & bubble counter. Unit comes with dual gauges each with dual reading of both psi & kg/cm. Left gauge meters tank capacity and right gauge meters flow. Needle valve flow control provides for precise measurement.

The solenoid valve comes with a 1.5 meter power cord. (CO2 bottle is not included)

Recommended best if used with our MC122 pH Controller.

MA991B/1 Combination Glass pH electrode - With BNC Connector and 1 meter cable by Milwaukee

The Milwaukee MA991B/1 is a lab grade single junction, gel filled glass replacement pH Probe for any Milwaukee BNC connector meter This electrode is designed for the education market, is easy-to-clean and great for students to learn with. The MA991B/1 has a glass body, high impedance, low maintenance (no refilling required) and is designed for fast accurate response. It comes with a 1 meter (3') cable, BNC connector and can withstand temperatures to -5 to 70°C (23 to 158°F) (meter(s) sold separately).

The probe connects quickly and tightly with a BNC connector. No worries of slipping off.

MC110 pH Monitor by Milwaukee

The MC Monitors are designed to continuously monitor pH, EC or TDS values directly in your reservoir. Each unit features a user selectable set-point. An LED visual alarm is activated and flashes when the pH, EC or TDS level rises either Above or Below (user selected) that set-point.

All these instruments run on a 12V adapter so there's no need to worry about failed batteries and each unit comes with mounting kit, probe, probe holder and starter calibration solution.

Professional pH monitor especially designed for use with aquariums.

• User selectable Hi/Low Set Point
• Manual 2 points calibration
• Visual LED alarm
• Supplied with 12 VDC adapter, mounting kit, and 20ml pH 7.01 calibration solution
• Double junction pH electrode with 2m cable (BNC connector)

MC120 pH Monitor by Milwaukee

The MC Monitors are designed to continuously monitor pH, EC or TDS values directly in your reservoir. Each unit features a user selectable set-point. An LED visual alarm is activated and flashes when the pH, EC or TDS level rises either Above or Below (user selected) that set-point.

All these instruments run on a 12V adapter so there's no need to worry about failed batteries and each unit comes with mounting kit, probe, probe holder and starter calibration solution.

Professional pH monitor especially designed for use with aquariums.

• User selectable Hi/Low Set Point
• Manual 2 points calibration
• Visual LED alarm
• Supplied with 12 VDC adapter, mounting kit, and 20ml pH 7.01 calibration solution
• Double junction pH electrode with 2m cable (BNC connector)

MC122 pH Controller by Milwaukee

With Milwaukee's MC Controllers you can monitor and control pH and/or ORP levels.

The Milwaukee Instruments "MC" Controllers have a user selectable set point and a visual "Power Activated" LED notification light. Power to the controller box is turned on when the reading is Above or Below (user selected) the selected set point. These MC Controllers are ideal for CO2 or ozone dosing.

With each Milwaukee Smart controller, your aquarium will have the individual attention that it needs.

Each unit comes with 12 VDC adapter, mounting kit, probe, probe holder and starter calibration solution for pH. (factory calibrated for ORP)

Professional pH controller especially designed for use with aquariums.

• User selectable Hi/Low Set Point
• Manual 2 points calibration
• Visual LED alarm
• Supplied with 12 VDC adapter and mounting kit
• Power plug for CO2 dosing
• Double junction pH electrode with 2m cable (BNC connector)

MC125 pH / ORP Controller by Milwaukee

With Milwaukee's MC Controllers you can monitor and control pH and/or ORP levels.

The Milwaukee Instruments "MC" Controllers have a user selectable set point and a visual "Power Activated" LED notification light. Power to the controller box is turned on when the reading is Above or Below ( user selected ) the selected set point. These MC Controllers are ideal for CO2 or ozone dosing.

With each Milwaukee Smart controller, your aquarium will have the individual attention that it needs.

Each unit comes with 12 VDC adapter, mounting kit, probe, probe holder and starter calibration solution for pH. (factory calibrated for ORP)

• User selectable Hi/Low Set Point
• Manual 2 points calibration
• Visual LED alarm
• Supplied with 12 VDC adapter and mounting kit
• 1 power plug for CO2 dosing and 1 power plug for O3 dosing
• Double junction pH electrode and platinum ORP electrode (BNC connector)

MC310 EC - Conductivity Monitor by Milwaukee

The MC Monitors are designed to continuously monitor pH, EC or TDS values directly in your reservoir. Each unit features a user selectable set-point. An LED visual alarm is activated and flashes when the pH, EC or TDS level rises either Above or Below (user selected) that set-point.

All these instruments run on a 12V adapter so there's no need to worry about failed batteries and each unit comes with mounting kit, probe, probe holder and starter calibration solution.

• User selectable Hi/Low Set Point
• Manual 1 points calibration
• Visual LED alarm
• Supplied with 12 VDC adapter, mounting kit, and 20ml 1413 µS/cm calibration solution
• MA811/2 EC Conductivity Probe with 2m cable (BNC connector)

MC311 EC Controller by Milwaukee

The Milwaukee MC311 PRO Conductivity (EC) controller lets you measure and adjust EC levels automatically.

SUMMARY

The MC311 EC controller automatically monitors and fine-tunes EC levels. Just set your EC parameters and let the Milwaukee EC Controller do the rest.

The Milwaukee PRO EC controller is preferred by people looking to dial in their testing program when they have an ongoing need to maintain levels. Common uses are nutrient tanks and aquariums.

The Milwaukee PRO EC controller offers:

ACCURACY

The Milwaukee PRO EC controller offers an accuracy to ±2% full scale.

AUTOMATION

The controller provides a control range of 0.0 to 10.0 mS/cm with alarms that activate when readings are higher or lower than set point.

COMPATIBLE DOSING PUMP

Milwaukee also offers the optional MP810 dosing pump

EASY INSTALLATION

This EC Controller comes with a complete mounting kit including a probe holder.

DESIGN FEATURES

• Fast easy to read current results with large digital LCD readout and visual LED alarm
• Accurate to ±2% full scale (0.0 pH to 10.0 mS/cm) with the user selectable high/low set points
• Simple one-point calibration for increased accuracy with manual trimmers for easy adjustment
• MA812/2 hardwired EC probe included
• 6.5 feet probe cables for extra flexibility when testing
• 12 VDC power supply

MC410 TDS - PPM Monitor by Milwaukee

The MC Monitors are designed to continuously monitor pH, EC or TDS values directly in your reservoir. Each unit features a user selectable set-point. An LED visual alarm is activated and flashes when the pH, EC or TDS level rises either Above or Below (user selected) that set-point.

All these instruments run on a 12V adapter so there's no need to worry about failed batteries and each unit comes with mounting kit, probe, probe holder and starter calibration solution.

• User selectable Hi/Low Set Point
• Manual 1 points calibration
• Visual LED alarm
• Supplied with 12 VDC adapter, mounting kit, and 20ml 1382ppm calibration solution
• MA81/2 PPM Probe with 2m cable (BNC connector)

MC510 ORP Controller by Milwaukee

With Milwaukee's MC Controllers you can monitor and control pH and/or ORP levels.

The Milwaukee Instruments "MC" Controllers have a user selectable set point and a visual "Power Activated" LED notification light. Power to the controller box is turned on when the reading is Above or Below ( user selected ) the selected set point. These MC Controllers are ideal for CO2 or ozone dosing.

With each Milwaukee Smart controller, your aquarium will have the individual attention that it needs.

Each unit comes with 12 VDC adapter, mounting kit, probe, probe holder and starter calibration solution for pH. (factory calibrated for ORP)

• User selectable Hi/Low Set Point
• Visual LED alarm
• Supplied with 12 VDC adapter
• 1 power plug for O3 dosing
• Platinum ORP electrode (BNC connector)

MC720 Ph Contoller With Dosing Pump Kit by Milwaukee

The MC122 pH controller and dosing pump (MP810) provides fully automated pH control of aqueous solutions in hydroponic systems. It has been specifically designed to control the pH in mixing tanks for fertilization. The small and precise flow of the peristaltic pump allows you to maintain ideal pH values in your tank.

After selecting the desired pH setting from 5.5 to 9.5 pH, the pH controller measures the pH value of the solution and automatically adds pH adjustment (acid or alkaline) to change the liquid s pH to the selected level.

MC740 EC Controller With Dosing Pump Kit by Milwaukee

The Milwaukee MC740 PRO Conductivity (EC) controller and pump lets you measure and adjust EC levels automatically.

CONTROL THE EC AND FERTILIZER DOSAGE IN YOUR TANK AUTOMATICALLY

The MC740 kit includes the MC311 EC controller and the MP810 dosing pump to automatically monitor and fine-tune EC levels. Just set your EC parameters and let the Milwaukee EC Controller and pump do the rest.

The Milwaukee PRO EC controller kit is preferred by people looking to dial in their testing program when they have an ongoing need to maintain levels. Common uses are nutrient tanks.

The Milwaukee PRO EC controller and pump offers:

ACCURACY

The Milwaukee PRO EC controller offers an accuracy to ±2% full scale.

AUTOMATION

The controller provides a control range of 0.0 to 10.0 mS/cm with alarms that activate when readings are higher or lower than set point.

COMPATIBLE DOSING PUMP

The Milwaukee MP810 dosing pump (designed specifically for use with the MC311) is included in the kit.

EASY INSTALLATION

The MC740 EC controller and pump kit comes with a complete mounting kit including a probe holder.

DESIGN FEATURES

• Fast easy to read current results with large digital LCD readout and visual LED alarm
• Accurate to ±2% full scale (0.0 pH to 10.0 mS/cm) with the user selectable high/low set points
• Simple one-point calibration for increased accuracy with manual trimmers for easy adjustment
• MA812/2 hardwired EC probe included
• 6.5 feet probe cables for extra flexibility when testing
• 12 VDC power supply
• Pump provides a maximum pressure of 1.5 bar or more than 50 feet of head pressure with a 0.16 GPM dosing flow.

MC745 EC Controller by Milwaukee

The Milwaukee MC745 PRO Conductivity (EC) controller and pump lets you measure and adjust EC levels automatically.

CONTROL THE EC AND FERTILIZER DOSAGE IN YOUR TANK AUTOMATICALLY

The MC745 kit includes the MC311 EC controller and two MP810 dosing pumps to automatically monitor and fine-tune EC levels. Just set your EC parameters and let the Milwaukee EC Controller and pumps do the rest.

The Milwaukee MC745 PRO controller kit is preferred by people looking to dial in their testing program when they have an ongoing need to maintain levels. Common uses are nutrient tanks.

The Milwaukee PRO EC controller and pumps offers:

ACCURACY

The Milwaukee PRO EC controller offers an accuracy to ±2% full scale.

AUTOMATION

The controller provides a control range of 0.0 to 10.0 mS/cm with alarms that activate when readings are higher or lower than set point.

COMPATIBLE DOSING PUMP

The Milwaukee MP810 dosing pump (designed specifically for use with the MC311) is included in the kit.

EASY INSTALLATION

The MC745 EC controller and pump kit comes with a complete mounting kit including a probe holder.

DESIGN FEATURES

• Fast easy to read current results with large digital LCD readout and visual LED alarm
• Accurate to ±2% full scale (0.0 pH to 10.0 mS/cm) with the user selectable high/low set points
• Simple one-point calibration for increased accuracy with manual trimmers for easy adjustment
• MA812/2 hardwired EC probe included
• 6.5 feet probe cables for extra flexibility when testing
• 12 VDC power supply
• Pump provides a maximum pressure of 1.5 bar or more than 50 feet of head pressure with a 0.16 GPM dosing flow.

MC811 MAX pH/EC/Temp Monitor by Milwaukee

ACCURATE. SIMPLE. RELIABLE. 24/7 PH/TDS/TEMP MONITORING.

Why Guard when you can Monitor! The Milwaukee MC811 MAX pH/EC/Temp Monitor lets you monitor your pH/EC/Temp levels 24/7 automatically.

COMMENTS FROM FIELD TESTING

"I run this unit 24/7 and have not had any problems for the past two months. I can monitor 24/7, point a camera on it and connect to my phone."
"Easy to calibrate."
"Using this now, far less expensive than what my friends paid ... I recommend this to any serious grower."

SUMMARY

The MC811 MAX Monitor automatically monitors and displays pH/EC/Temp levels. Just calibrate the parameters and let the Milwaukee MAX Monitor do the rest.

The Milwaukee MC811 MAX pH/EC/Temp Monitor is preferred by people looking to know 24/7 what their pH and nutrient levels are on an ongoing basis. Common uses are nutrient tanks, Hydroponics and aquariums.

The Milwaukee MAX pH/EC/Temp Monitor offers:

ACCURACY

The Milwaukee MAX Monitor offers an accuracy to ± 0.2 pH with two point manual calibration, EC accuracy of ±2% Full Scale and ±0.5 °F (0.3 °C) temperature accuracy.

AUTOMATION

Just calibrate the parameters and begin to monitor 24/7!

EASY INSTALLATION

The MC811 MAX pH/EC/Temp Monitor comes with a complete mounting kit including a probe holder.

DESIGN FEATURES

• Fast easy to read current results with 3 large digital BACKLIT LCD readouts.
• Accurate to ±0.2 pH (0.0 pH to 12.0 pH).
• Accurate ±2% Full Scale EC.
• External Switch atop the unit converts EC conductivity to EC using 0.5 or 0.7 conversion factor.
• Simple two-point pH calibration and one point EC, for increased accuracy with manual trimmers for easy adjustment.
• Gel-filled, double junction MA911B/2 (included) lab grade pH electrode for low maintenance and high performance.
• 6.5 feet probe cables for extra flexibility when testing.
• 12 VDC power supply.

USE AND CARE

pH meters usually start performing poorly because of problems with the probe. The two parts of the pH probe that cause problems are the glass sensing bulb and the reference junction.

SENSING BULB

The glass bulb loses sensitivity with use and will eventually fail. This is true of all pH probes.

REFERENCE JUNCTION

The reference junction is a small hole that allows the meter to compare the sample to a reference. The reading is generated based on the electrical difference between the sample and reference. If the junction hole gets clogged, the pH probe will no longer function.

You can extend the life of your pH electrode in the following ways.

STORAGE

The pH probe needs to be kept hydrated. Long periods of dry storage will damage the sensitivity of the probe. Allowing the probe to dry out may also result in the junction hole getting clogged.

Storing in pH probe storage solution or pH calibration buffers will help address both these issues. Do not store in tap water and DI water. This will damage the sensitivity of the probe.

The best way to store the probe is with the probe's cap filled with storage solution or calibiration buffer and the cap tightened to prevent leakage. It is also recommended that to store the electrode upright to further reduce the potential for leakage.

CLEANING

Residue from the sample can impact the sensitivity of the sensing bulb and clog the junction. This is especially true if the sample has a lot of organic material. We recommend regularly soaking your electrode in cleaning solution.

CALIBRATION

The pH sensing bulbs become less sensitive over time so make sure that you are calibrating reguarly to keep your PRO pH controller accurate. Also, calibrate after cleaning or a long period of storage.