Milwaukee

AG900 Standard Portable pH / Conductivity / TDS Combination Meter Kit by Milwaukee

3 meters in 1! This meter allows you to measure pH, EC (conductivity) and TDS with just one instrument and one single probe!

The AG900, with a conductivity range that goes up to 6.00 mS/cm and the TDS up to 4000 ppm is ideal for testing in crop production. Soil and well water pH that is too acidic or alkaline can have an adverse effect on plant nutrient and water uptake and directly effect the efficiency of fertilizer, herbicides and pesticides. Soil Conductivity is checked before fertilizer application to pinpoint field needs and after fertilization to establish its effectiveness.

Supplied with the SE600 interchangeable probe to measure pH, Conductivity and TDS. The pH electrode utilizes a fiber junction to reduce contamination when measuring fertilizer solutions. Both meters calibrate manually in pH, Conductivity and TDS.

Includes

• MW802 ( ph/ec/tds ) Combination Meter
• Carrying Case
• pH 230ml Bottle 7.01 Calibration Solution
• EC - Conductivity Calibration Solution in 230ml Bottle

AQ600 Standard Portable Dissolved Oxygen Meter Kit by Milwaukee

The AQ600 is a Portable Dissolved Oxygen meter ideal for use in school laboratories. Dissolved Oxygen measurements are also very important in fish farms and ponds, where Oxygen levels are continuously monitored to obtain optimal reproduction.

The AQ600 calibrates easily in 2 points (at 100% saturated air and in 0 Oxygen solution) and has Automatic Temperature Compensation which guarantees the highest accuracy. The low battery warning, easy to replace screw on cap membranes make this meter very simple to operate.

AQ600 is supplied complete with a MA840 D.O. polarographic probe with 3 m cable, calibration screwdriver, 2 spare membranes, MA7040 (20 mL) electrolyte solution, battery and instructions.

Includes

• MW600 DO Meter
• Membrane Electrolyte Refill Solution 230ml bottle
• 5 Extra Membranes
• Protective Case
• 9 Volt Battery & Testing Manual

BEM101 pH Mini-Bench Meter by Milwaukee

• Double junction electrode with 1 meter cable
• Manual calibration 2 points
• Faster Processor with The New Chipset and Motherboard
• 100% Larger & Easier To Read LED Display
• Smaller, Ergonomic & Lighter Case Design
• Includes 9vDC power supply, mounting Kit, SE220 pH probe, probe holder, and 20ml pH 7.01 & 4.01 calibration solution

BEM401 TDS - PPM Mini-Bench Meter by Milwaukee

• Manual calibration 1 points
• Faster Processor with The New Chipset and Motherboard
• 100% Larger & Easier To Read LED Display
• Smaller, Ergonomic & Lighter Case Design
• Includes 9vDC power supply, mounting Kit, MA811D/1 TDS probe, probe holder, and 20ml 1382ppm calibration solution

BEM500 ORP Mini-Bench Meter by Milwaukee

• Factory calibrated
• Faster Processor with The New Chipset and Motherboard
• 100% Larger & Easier To Read LED Display
• Smaller, Ergonomic & Lighter Case Design
• Includes 9vDC power supply, mounting Kit, SE300 Platinum probe, and probe holder

BEM500 pH/EC/TDS Combo Mini-Bench Meter by Milwaukee

• Faster Processor with The New Chipset and Motherboard
• 100% Larger & Easier To Read LED Display
• Smaller, Ergonomic & Lighter Case Design
• Includes 9vDC power supply, mounting Kit, SE600 Combo probe, probe holder, and a 20ml sachet of calibration solution of pH 7.01, 1500ppm, and 1413µS/cm

C65 Waterproof Conductivity Tester with Replaceable Electrode (low range) by Milwaukee

These instruments are designed for all applications. It's IP65 Waterproof casing and replaceable electrode make them suitable also for heavy duty applications, such as Waste Water treatment and Agriculture. The modular design allows easy electrode and battery replacement.

All Waterproof testers are supplied in a leather casing complete with calibration solution, batteries, instruction manual and screwdriver for calibration.

The C65 is a waterproof conductivity tester (for fresh water) with automatic temperature compensation, 1 point manual calibration and a range of 0 to 1999 µS/cm.

C66 Waterproof Conductivity Tester with Replaceable Electrode (high range) by Milwaukee

The C66 is a conductivity IP65 waterproof tester, specifically designed for the hydroponics and Agricultural markets, with automatic temperature compensation and 1 point manual calibration. The tester has a range of 0.00 to 10.00 mS/cm.

The C66 has a replaceable electrode and is supplied in a casing with calibration solution sachets (M10031) and screwdriver for calibration. The modular design allows easy electrode and battery replacement.

CD600 TDS Tester with ATC and 1 point manual calibration by Milwaukee

The Milwaukee CD600 Total Dissolved Solids (TDS) Pen is designed for hydroponics, aquariums, horticulture, water conditioning and many other applications. The CD600 helps you make sure that your plants are receiving the right amount of nutrient or helps you keep your filters up-to-date and clean for water filtration. Keep TDS in your target range to help your achieve better results.

DESIGN FEATURES

• Measures Total Disolved (TDS) direct and with automatic temperature compensation.
• Ideal range for hydroponics (0 to 1990 ppm).
• Units in ppm easily convertable to μS/cm.
• Factory calibrated with the ability to recalibrate if needed.
• Automatic Temperature Compensation (ATC).
• 350 hours continuous use (4 x 1.5V batteries included).
• Simple one point calibration.

MAINTENANCE

TDS/PPM electrodes can develop nutrient build up over time. To miminize build up, always rinse the probe in fresh tap or DI water after every use.

CONVERTING TDS TO EC

The Milwaukee TDS Pen, like all TDS meters, provides a measure of Total Dissolved Solids (ppm) reading, of contaminates per unit of volume in a solution.

TDS/PPM is often converted to μS/cm. Different scales include the 500 scale, 650 scale and the 700 scale.

Your TDS/PPM readings can be approximately converted to μS/cm as shown in the examples below.

1 ppm = 2 μS/cm on the 0.5 factor scale

1 ppm = 1.43 μS/cm on the 442 scale or .70 factor scale

CD601 Conductivity Tester with ATC and 1 point manual calibration by Milwaukee

The Milwaukee CD601 digital electrical conductivity (EC) Pen is designed for aquariums, aquaculture, pools, water conditioning and many other applications. The CD601 helps you make sure that your water has the right amount of nutrient to help keep fish tanks healthy or helps you keep your filters up-to-date and clean for water filtration. Keep EC in your target range to help your achieve better results.

DESIGN FEATURES

• Measures microSiemens (μS/cm) direct and with automatic temperature compensation.
• Ideal range for aquariums (0 to 1990 μS/cm).
• Units in μS/cm are easily convertable to (ppm).
• Factory calibrated with the ability to recalibrate if needed.
• Automatic Temperature Compensation (ATC).
• 350 hours continuous use (4 x 1.5V batteries included).
• Simple one point calibration.

MAINTENANCE

EC electrodes can develop nutrient build up over time. To miminize build up, always rinse the probe in fresh tap or DI water after every use.

CONVERTING EC TO TDS

The Milwaukee EC Pen, like all conductivity meters, provides a measure of electrically charged ions in a solution and is an absolute measure of conductivity.

EC is often converted to TDS in parts per million (ppm). Different scales include the 500 scale, 650 scale and the 700 scale. However, true PPM can only be determined through chemical analysis.

Your mS/cm reading can be approximately converted to TDS (ppm) as shown in the examples below.

2,000 μS/cm = 2.0 mS/cm = 1000 ppm on .50 factor scale

2,000 μS/cm = 2.0 mS/cm = 1400 ppm on the 442 scale or .70 factor scale

CD610 TDS Tester with ATC and 1 point manual calibration by Milwaukee

The Milwaukee CD610 Total Dissolved Solids High Range (PPM) Pen is designed for aquariums, pools and education and many other applications. The CD610 helps make sure that you keep your fish tank water clean and healthy. It is a cost effective tool for teacher's science labs. Keep PPM in your target range to help your achieve better results.

DESIGN FEATURES

• Measures Total Dissovled Solids (PPM) direct and with automatic temperature compensation.
• Ideal range for aquariums and pools (0 to 10000 ppm).
• Units in ppm easily convertable to μS/cm.
• Factory calibrated with the ability to recalibrate if needed.
• Automatic Temperature Compensation (ATC).
• 350 hours continuous use (4 x 1.5V batteries included).
• Simple one point calibration.

MAINTENANCE

EC/PPM electrodes can develop nutrient build up over time. To miminize build up, always rinse the probe in fresh tap or DI water after every use.

CONVERTING TDS TO EC

The Milwaukee TDS/PPM Pen, like all TDS meters, provides a reading measured in parts per million of contaminates per unit of volume in a solution.

TDS/PPM is often converted to uS/cm. Different scales include the 500 scale, 650 scale and the 700 scale.

Your TDS/PPM reading can be approximately converted to μS/cm as shown in the examples below.

1 ppm = 2 μS/cm on the 0.5 factor scale

1 ppm = 1.43 μS/cm on the 442 scale or .70 factor scale

CD611 Conductivity Tester with ATC and 1 point manual calibration by Milwaukee

The Milwaukee Conductivity Pen is designed for hydroponic and other growers to help you make sure that your plants are receiving the right amount of nutrient. Keep EC in your target range to help your achieve better results.

DESIGN FEATURES

• Measures conductivity and temperature with automatic temperature compensation
• Ideal range for hydroponics (0 to 20,000 μS/cm)
• Units in μS/cm easily convertable to ppm
• Factory calibrated with the ability to recalibrate if needed
• 350 hours continuous use (3 x 1.5V batteries included)

MAINTENANCE

EC electrodes can develop nutrient build up over time. To miminize build up, always rinse the probe in fresh tap water after every use.

CONVERTING EC TO TDS

The Milwaukee EC Pen, like all conductivity meters, provides a measure of electrically charged ions in a solution and is an absolute measure of conductivity.

EC is often converted to TDS in parts per million (ppm). Different scales include the 500 scale, 650 scale and the 700 scale. However, true PPM can only be determined through chemical analysis.

Your mS/cm reading can be approximately converted to TDS (ppm) as shown in the examples below.

2,000 μS/cm = 2.0 mS/cm = 1000 ppm on .50 factor scale

2,000 μS/cm = 2.0 mS/cm = 1400 ppm on the 442 scale or .70 factor scale

CD97 TDS Tester with ATC and 1 point manual calibration by Milwaukee

The Milwaukee CD97 Total Dissolved Solids Low Range (PPM) Pen is designed for water conditioning, education and many other applications. The CD97 helps you make sure that your keep your filters up-to-date and clean for water filtration and is a cost effective tool for teacher's science labs. Keep PPM in your target range to help your achieve better results.

DESIGN FEATURES

• Ideal range for water conditioning (0 to 999 ppm).
• Units in ppm easily convertable to μS/cm.
• Factory calibrated with the ability to recalibrate if needed.
• Automatic Temperature Compensation (ATC).
• 300 hours continuous use (4 x 1.5V batteries included).
• Simple one point calibration.

MAINTENANCE

EC/PPM electrodes can develop nutrient build up over time. To miminize build up, always rinse the probe in fresh tap or DI water after every use.

CONVERTING TDS TO EC

The Milwaukee TDS/PPM Pen, like all TDS meters, provides a reading measured in parts per million of contaminates per unit of volume in a solution.

TDS/PPM is often converted to uS/cm. Different scales include the 500 scale, 650 scale and the 700 scale.

Your TDS/PPM reading can be approximately converted to uS/cm as shown in the examples below.

1 ppm = 2 μS/cm on the 0.5 factor scale

1 ppm = 1.43 μS/cm on the 442 scale or .70 factor scale

EC40 EC Nutrient Stick by Milwaukee

The Milwaukee EC/TDS Nutrient Meter is designed for Hydroponics, horticulture and agriculture to help you make sure that your vegetables and plants are receiving the right amount of nutrient to promote healthy growth with low to zero product waste. Keep EC/TDS in your target range to help your achieve better results.

DESIGN FEATURES

• Measures conductivity (EC) and total dissolved solids (TDS) with automatic temperature compensation.
• Ideal range for Hydroponics (0.2 to 4 mS/cm | 2 to 40 CF | 140 to 2800 ppm 0.7 scale | 100 to 2000 ppm 0.5 scale).
• Units directly in mS/cm/CF/PPM (no conversions required).
• Factory calibrated no continious calibration required.
• High accuracy.
• Automatic Temperature Compensation (ATC).
• Auto on/off feature.
• Blue LED display.
• Graphite electrode in ABC + PC body.
• Battery level indicators.
• Battery life up to 3 years with approx. 10 measurements per day.
• 3 X 1.5V AA (batteries included).

MAINTENANCE

EC/TDS electrodes can develop nutrient build up over time. To miminize build up, always rinse the probe in fresh tap or DI water after every use.

CONVERTING EC TO TDS

The Milwaukee EC40 meter, like all conductivity meters, provides a measure of electrically charged ions in a solution and is an absolute measure of conductivity.

EC is often converted to TDS in parts per million (ppm). Different scales include the 500 scale, 650 scale and the 700 scale. However, the EC40 has all the readings direct EC/TDS/CF.

Your μS/cm reading can be approximately converted to TDS (ppm) as shown in the examples below.

1 μS/cm = 0.5 ppm on a .5 factor scale

1 μS/cm = 0.7 ppm on a .70 factor scale (442)

EC59 Pocket-size Conductivity / TDS / Temperature Meter with Replaceable Electrode by Milwaukee

This new waterproof Pocket-size EC/TDS/Temp Meter include features such as a replaceable probe, temperature in °C or °F, automatic temperature compensation with adjustable ß, battery level indicator, stability indicator, automatic shut-off and automatic calibration all in a floating, waterproof casing.

EC59 shows on the dual-level LCD the EC (3999 µS/cm) or TDS (2000 ppm) value. It also displays the temperature from 0.0 to 60.0°C (or 32.0 to 140.0°F) on the secondary level at the same time.

EC60 Pocket-size Conductivity / TDS / Temperature Meter with Replaceable Electrode by Milwaukee

This new waterproof Pocket-size EC/TDS/Temp Meter include features such as a replaceable probe, temperature in °C or °F, automatic temperature compensation with adjustable ß, battery level indicator, stability indicator, automatic shut-off and automatic calibration all in a floating, waterproof casing.

EC60 shows on the dual-level LCD the EC (20.00 mS/cm) or TDS (10.00 ppt) value. It also displays the temperature from 0.0 to 60.0°C (or 32.0 to 140.0°F) on the secondary level at the same time.