GfG

Calibration Kit with 34L Nitrogen (N2) Calibration Gas and 34L Carbon Dioxide (CO2) Calibration Gas (25% vol.)

34L Nitrogen Dioxide (NO2) Calibration Gas Aluminum Cylinder, 10 PPM, N2 Balance

58L Hydrogen Sulfide (H2S) Calibration Gas Aluminum Cylinder, 50 PPM, Air Balance

Ammonia (NH3) Replacement Sensor, 1 ppm Resolution, 0 - 500 ppm Range

2109-500F EC 21 Fixed Gas Transmitter with Internal Sensor, Ammonia (NH3), 2 ppm, 0 - 500 ppm by GfG

GfG s EC 21 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Simple gas detection

The EC 21 is the simplest way to monitor ambient conditions. Simply attach the EC21 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in the air.

The EC 21 is reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector hasa "quick disconnect" feature to simplify transmitter installation and service.

Mounting Position of the EC 21

To determine the mounting position of the EC 21 it is important to know and consider the ambient conditions. To achieve the best results, the ventilation conditions and the density of the gases need to be considered.

The EC 21 must be installed so that the gas reaches the sensor even in poorly ventilated areas. If necessary, check the area with a smoke cartridge.

Other influences such as water (rain, dripping or condensation) and dust need to be considered as well.

Features

• Simple to use and extremely economical
• Robust housing is corrosion resistant and dust-tight>
• Linear 4 to 20 mA output signal
• 18 - 24 VDC

1418-105 Micro IV Single Gas Detector with 3-Year Sensor Warranty, Carbon Monoxide (CO), 0 - 300 ppm by GfG

Durable, compact design

The Micro IV is compact, robust and very easy to use. It is designed to be used in the harshest environments. The Micro IV includes a set of rubber boots to withstand hard knocks and drops.

Widest Range of sensors

Micro IV detectors are available for use with a wide range of long-lasting, interchangeable smart-sensors for the detection of O₂, H₂S, CO, NH₃, SO₂, Cl₂, ClO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂ and more.

Easy Operation

The Micro IV keeps gas detection simple. Most day-to-day functions are controlled with a single button, and calibration is fully automatic. Simply select the calibration mode from the keypad, attach the adapter and flow gas to the sensor. The GfG Autocal® feature automatically makes the adjustments and updates the information in the instrument s on-board memory.

Up to six months of battery life

The Micro IV delivers up to 3,000 hours of continuous operation from a single off the shelf AA alkaline battery. Battery replacement, when needed, can be completed in less than 30 seconds and requires no tools.

Clip-on attachment

The Micro IV comes with a heavy duty alligator clip that allows the detector to be conveniently clipped on to clothing and if so desired near the breathing zone.

Optional motorized pump

The Micro IV is available with an optional motorized pump to allow sampling from a remote location. The motorized pump may also be used in extraordinary harsh conditions, such as extreme heat, where it may be desirable to protect the instrument under protective clothing; using a tube the pump can draw air samples from the breathing zone.

Large graphic display

The Micro IV detector features a large backlit easy-to-read graphic display that provides a continuous readout for the sensor installed. By pressing a single button additional information such as Peak, STEL and TWA readings my be displayed.

Audible, vibrating and visual alarms

The Micro IV detector features a loud alarm (95db at 12 inches), a built-in vibrating alarm and a bright multi-directional visual LED alarm light.

Lifetime warranty

The Micro IV carries a lifetime warranty on non-consumable components and two or more years of warranty on most sensors. Select sensors such as O2, H2S, and CO carry a full three year warranty against failure.

DS220 docking station

The Micro IV is available with a six position fully automatic docking station. The docking station makes bump test and calibration even easier and all maintenance records are stored automatically. The docking station fully test sensor response, alarms and other functionality.

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Standard Accessories

• Micro IV detector
• Specified Sensor
• Alkaline Battery
• Rubber Boot
• Manual

1418-103 Micro IV Single Gas Detector with 2-Year Sensor Warranty, Carbon Monoxide (CO-H), 0 - 300 ppm by GfG

Durable, compact design

The Micro IV is compact, robust and very easy to use. It is designed to be used in the harshest environments. The Micro IV includes a set of rubber boots to withstand hard knocks and drops.

Widest Range of sensors

Micro IV detectors are available for use with a wide range of long-lasting, interchangeable smart-sensors for the detection of O₂, H₂S, CO, NH₃, SO₂, Cl₂, ClO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂ and more.

Easy Operation

The Micro IV keeps gas detection simple. Most day-to-day functions are controlled with a single button, and calibration is fully automatic. Simply select the calibration mode from the keypad, attach the adapter and flow gas to the sensor. The GfG Autocal® feature automatically makes the adjustments and updates the information in the instrument s on-board memory.

Up to six months of battery life

The Micro IV delivers up to 3,000 hours of continuous operation from a single off the shelf AA alkaline battery. Battery replacement, when needed, can be completed in less than 30 seconds and requires no tools.

Clip-on attachment

The Micro IV comes with a heavy duty alligator clip that allows the detector to be conveniently clipped on to clothing and if so desired near the breathing zone.

Optional motorized pump

The Micro IV is available with an optional motorized pump to allow sampling from a remote location. The motorized pump may also be used in extraordinary harsh conditions, such as extreme heat, where it may be desirable to protect the instrument under protective clothing; using a tube the pump can draw air samples from the breathing zone.

Large graphic display

The Micro IV detector features a large backlit easy-to-read graphic display that provides a continuous readout for the sensor installed. By pressing a single button additional information such as Peak, STEL and TWA readings my be displayed.

Audible, vibrating and visual alarms

The Micro IV detector features a loud alarm (95db at 12 inches), a built-in vibrating alarm and a bright multi-directional visual LED alarm light.

Lifetime warranty

The Micro IV carries a lifetime warranty on non-consumable components and two or more years of warranty on most sensors. Select sensors such as O2, H2S, and CO carry a full three year warranty against failure.

DS220 docking station

The Micro IV is available with a six position fully automatic docking station. The docking station makes bump test and calibration even easier and all maintenance records are stored automatically. The docking station fully test sensor response, alarms and other functionality.

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Standard Accessories

• Micro IV detector
• Specified Sensor
• Alkaline Battery
• Rubber Boot
• Manual

1418-103K Micro IV Value Kit with 2-Years Sensor Warranty, Carbon Monoxide (CO-H), 0 - 300 ppm by GfG

Durable, compact design

The Micro IV is compact, robust and very easy to use. It is designed to be used in the harshest environments. The Micro IV includes a set of rubber boots to withstand hard knocks and drops.

Widest Range of sensors

Micro IV detectors are available for use with a wide range of long-lasting, interchangeable smart-sensors for the detection of O₂, H₂S, CO, NH₃, SO₂, Cl₂, ClO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂ and more.

Easy Operation

The Micro IV keeps gas detection simple. Most day-to-day functions are controlled with a single button, and calibration is fully automatic. Simply select the calibration mode from the keypad, attach the adapter and flow gas to the sensor. The GfG Autocal® feature automatically makes the adjustments and updates the information in the instrument s on-board memory.

Up to six months of battery life

The Micro IV delivers up to 3,000 hours of continuous operation from a single off the shelf AA alkaline battery. Battery replacement, when needed, can be completed in less than 30 seconds and requires no tools.

Clip-on attachment

The Micro IV comes with a heavy duty alligator clip that allows the detector to be conveniently clipped on to clothing and if so desired near the breathing zone.

Optional motorized pump

The Micro IV is available with an optional motorized pump to allow sampling from a remote location. The motorized pump may also be used in extraordinary harsh conditions, such as extreme heat, where it may be desirable to protect the instrument under protective clothing; using a tube the pump can draw air samples from the breathing zone.

Large graphic display

The Micro IV detector features a large backlit easy-to-read graphic display that provides a continuous readout for the sensor installed. By pressing a single button additional information such as Peak, STEL and TWA readings my be displayed.

Audible, vibrating and visual alarms

The Micro IV detector features a loud alarm (95db at 12 inches), a built-in vibrating alarm and a bright multi-directional visual LED alarm light.

Lifetime warranty

The Micro IV carries a lifetime warranty on non-consumable components and two or more years of warranty on most sensors. Select sensors such as O2, H2S, and CO carry a full three year warranty against failure.

DS220 docking station

The Micro IV is available with a six position fully automatic docking station. The docking station makes bump test and calibration even easier and all maintenance records are stored automatically. The docking station fully test sensor response, alarms and other functionality.

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Value Kit Configuration

• All standard accessories: Micro IV detector, Specified Sensor, Alkaline Battery, Rubber Boot, Manual
• Calibration Adapter
• Calibration Gas
• Fixed Flow Regulator
• ABS Carrying Case

Ammonia (NH3), 0 - 500 ppm, Replacement Sensor with 1-Year Warranty

Carbon Monoxide (CO) Replacement Sensor, 1 ppm Resolution, 0 - 2000 ppm Range

Carbon Monoxide (CO), 0 - 1,000 ppm, Replacement Sensor with 3-Year Sensor Warranty

Hydrogen Sulfide (H2S), - Standard 0 - 100 ppm, Replacement Sensor with 3-Years Warranty

1418-022 Micro IV Single Gas Detector with 3-Years Sensor Warranty, Oxygen (O2), 0 - 25% Vol. by GfG

Durable, compact design

The Micro IV is compact, robust and very easy to use. It is designed to be used in the harshest environments. The Micro IV includes a set of rubber boots to withstand hard knocks and drops.

Widest Range of sensors

Micro IV detectors are available for use with a wide range of long-lasting, interchangeable smart-sensors for the detection of O₂, H₂S, CO, NH₃, SO₂, Cl₂, ClO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂ and more.

Easy Operation

The Micro IV keeps gas detection simple. Most day-to-day functions are controlled with a single button, and calibration is fully automatic. Simply select the calibration mode from the keypad, attach the adapter and flow gas to the sensor. The GfG Autocal® feature automatically makes the adjustments and updates the information in the instrument s on-board memory.

Up to six months of battery life

The Micro IV delivers up to 3,000 hours of continuous operation from a single off the shelf AA alkaline battery. Battery replacement, when needed, can be completed in less than 30 seconds and requires no tools.

Clip-on attachment

The Micro IV comes with a heavy duty alligator clip that allows the detector to be conveniently clipped on to clothing and if so desired near the breathing zone.

Optional motorized pump

The Micro IV is available with an optional motorized pump to allow sampling from a remote location. The motorized pump may also be used in extraordinary harsh conditions, such as extreme heat, where it may be desirable to protect the instrument under protective clothing; using a tube the pump can draw air samples from the breathing zone.

Large graphic display

The Micro IV detector features a large backlit easy-to-read graphic display that provides a continuous readout for the sensor installed. By pressing a single button additional information such as Peak, STEL and TWA readings my be displayed.

Audible, vibrating and visual alarms

The Micro IV detector features a loud alarm (95db at 12 inches), a built-in vibrating alarm and a bright multi-directional visual LED alarm light.

Lifetime warranty

The Micro IV carries a lifetime warranty on non-consumable components and two or more years of warranty on most sensors. Select sensors such as O2, H2S, and CO carry a full three year warranty against failure.

DS220 docking station

The Micro IV is available with a six position fully automatic docking station. The docking station makes bump test and calibration even easier and all maintenance records are stored automatically. The docking station fully test sensor response, alarms and other functionality.

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Standard Accessories

• Micro IV detector
• Specified Sensor
• Alkaline Battery
• Rubber Boot
• Manual

Ammonia (NH3), 0 - 500 ppm, Replacement Sensor with 1-Year Warranty

58L Hydrogen Sulfide (H2S) Calibration Gas Aluminum Cylinder, 20 PPM, N2 Balance

Ammonia (NH3) Replacement Sensor, 2 ppm Resolution, 0 - 500 ppm Range

Extended 6-year sensor warranty (O2, H2S and CO)

1418-115 Micro IV Single Gas Detector with 2-Year Sensor Warranty, Nitric Oxide (NO), 0 - 100 ppm by GfG

Durable, compact design

The Micro IV is compact, robust and very easy to use. It is designed to be used in the harshest environments. The Micro IV includes a set of rubber boots to withstand hard knocks and drops.

Widest Range of sensors

Micro IV detectors are available for use with a wide range of long-lasting, interchangeable smart-sensors for the detection of O₂, H₂S, CO, NH₃, SO₂, Cl₂, ClO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂ and more.

Easy Operation

The Micro IV keeps gas detection simple. Most day-to-day functions are controlled with a single button, and calibration is fully automatic. Simply select the calibration mode from the keypad, attach the adapter and flow gas to the sensor. The GfG Autocal® feature automatically makes the adjustments and updates the information in the instrument s on-board memory.

Up to six months of battery life

The Micro IV delivers up to 3,000 hours of continuous operation from a single off the shelf AA alkaline battery. Battery replacement, when needed, can be completed in less than 30 seconds and requires no tools.

Clip-on attachment

The Micro IV comes with a heavy duty alligator clip that allows the detector to be conveniently clipped on to clothing and if so desired near the breathing zone.

Optional motorized pump

The Micro IV is available with an optional motorized pump to allow sampling from a remote location. The motorized pump may also be used in extraordinary harsh conditions, such as extreme heat, where it may be desirable to protect the instrument under protective clothing; using a tube the pump can draw air samples from the breathing zone.

Large graphic display

The Micro IV detector features a large backlit easy-to-read graphic display that provides a continuous readout for the sensor installed. By pressing a single button additional information such as Peak, STEL and TWA readings my be displayed.

Audible, vibrating and visual alarms

The Micro IV detector features a loud alarm (95db at 12 inches), a built-in vibrating alarm and a bright multi-directional visual LED alarm light.

Lifetime warranty

The Micro IV carries a lifetime warranty on non-consumable components and two or more years of warranty on most sensors. Select sensors such as O2, H2S, and CO carry a full three year warranty against failure.

DS220 docking station

The Micro IV is available with a six position fully automatic docking station. The docking station makes bump test and calibration even easier and all maintenance records are stored automatically. The docking station fully test sensor response, alarms and other functionality.

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Standard Accessories

• Micro IV detector
• Specified Sensor
• Alkaline Battery
• Rubber Boot
• Manual

1418-130 Micro IV Single Gas Detector with 2-Year Sensor Warranty, Hydrogen (H2), 0 -2000 ppm by GfG

Durable, compact design

The Micro IV is compact, robust and very easy to use. It is designed to be used in the harshest environments. The Micro IV includes a set of rubber boots to withstand hard knocks and drops.

Widest Range of sensors

Micro IV detectors are available for use with a wide range of long-lasting, interchangeable smart-sensors for the detection of O₂, H₂S, CO, NH₃, SO₂, Cl₂, ClO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂ and more.

Easy Operation

The Micro IV keeps gas detection simple. Most day-to-day functions are controlled with a single button, and calibration is fully automatic. Simply select the calibration mode from the keypad, attach the adapter and flow gas to the sensor. The GfG Autocal® feature automatically makes the adjustments and updates the information in the instrument s on-board memory.

Up to six months of battery life

The Micro IV delivers up to 3,000 hours of continuous operation from a single off the shelf AA alkaline battery. Battery replacement, when needed, can be completed in less than 30 seconds and requires no tools.

Clip-on attachment

The Micro IV comes with a heavy duty alligator clip that allows the detector to be conveniently clipped on to clothing and if so desired near the breathing zone.

Optional motorized pump

The Micro IV is available with an optional motorized pump to allow sampling from a remote location. The motorized pump may also be used in extraordinary harsh conditions, such as extreme heat, where it may be desirable to protect the instrument under protective clothing; using a tube the pump can draw air samples from the breathing zone.

Large graphic display

The Micro IV detector features a large backlit easy-to-read graphic display that provides a continuous readout for the sensor installed. By pressing a single button additional information such as Peak, STEL and TWA readings my be displayed.

Audible, vibrating and visual alarms

The Micro IV detector features a loud alarm (95db at 12 inches), a built-in vibrating alarm and a bright multi-directional visual LED alarm light.

Lifetime warranty

The Micro IV carries a lifetime warranty on non-consumable components and two or more years of warranty on most sensors. Select sensors such as O2, H2S, and CO carry a full three year warranty against failure.

DS220 docking station

The Micro IV is available with a six position fully automatic docking station. The docking station makes bump test and calibration even easier and all maintenance records are stored automatically. The docking station fully test sensor response, alarms and other functionality.

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Standard Accessories

• Micro IV detector
• Specified Sensor
• Alkaline Battery
• Rubber Boot
• Manual

Ammonia (NH3), 5 ppm, 0 to 500 ppm Replacement Sensors

2109-500 EC 21 Fixed Gas Transmitter with Internal Sensor, Ammonia (NH3), 1 ppm, 0 - 500 ppm by GfG

GfG s EC 21 transmitter for detecting toxic gases in ambient air is an inexpensive gas detection solution for use in a wide variety of today's industrial applications.

Simple gas detection

The EC 21 is the simplest way to monitor ambient conditions. Simply attach the EC21 to a GfG controller or a PLC to continuously and efficiently monitor the concentration of hazardous toxic contaminants in the air.

The EC 21 is reverse-wire protected to prevent damage due to incorrect wiring of the device. The power connector hasa "quick disconnect" feature to simplify transmitter installation and service.

Mounting Position of the EC 21

To determine the mounting position of the EC 21 it is important to know and consider the ambient conditions. To achieve the best results, the ventilation conditions and the density of the gases need to be considered.

The EC 21 must be installed so that the gas reaches the sensor even in poorly ventilated areas. If necessary, check the area with a smoke cartridge.

Other influences such as water (rain, dripping or condensation) and dust need to be considered as well.

Features

• Simple to use and extremely economical
• Robust housing is corrosion resistant and dust-tight>
• Linear 4 to 20 mA output signal
• 18 - 24 VDC

1418-120 Micro IV Single Gas Detector with 2-Year Sensor Warranty, Hydrogen Cyanide (HCN), 0 - 50 ppm by GfG

Durable, compact design

The Micro IV is compact, robust and very easy to use. It is designed to be used in the harshest environments. The Micro IV includes a set of rubber boots to withstand hard knocks and drops.

Widest Range of sensors

Micro IV detectors are available for use with a wide range of long-lasting, interchangeable smart-sensors for the detection of O₂, H₂S, CO, NH₃, SO₂, Cl₂, ClO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂ and more.

Easy Operation

The Micro IV keeps gas detection simple. Most day-to-day functions are controlled with a single button, and calibration is fully automatic. Simply select the calibration mode from the keypad, attach the adapter and flow gas to the sensor. The GfG Autocal® feature automatically makes the adjustments and updates the information in the instrument s on-board memory.

Up to six months of battery life

The Micro IV delivers up to 3,000 hours of continuous operation from a single off the shelf AA alkaline battery. Battery replacement, when needed, can be completed in less than 30 seconds and requires no tools.

Clip-on attachment

The Micro IV comes with a heavy duty alligator clip that allows the detector to be conveniently clipped on to clothing and if so desired near the breathing zone.

Optional motorized pump

The Micro IV is available with an optional motorized pump to allow sampling from a remote location. The motorized pump may also be used in extraordinary harsh conditions, such as extreme heat, where it may be desirable to protect the instrument under protective clothing; using a tube the pump can draw air samples from the breathing zone.

Large graphic display

The Micro IV detector features a large backlit easy-to-read graphic display that provides a continuous readout for the sensor installed. By pressing a single button additional information such as Peak, STEL and TWA readings my be displayed.

Audible, vibrating and visual alarms

The Micro IV detector features a loud alarm (95db at 12 inches), a built-in vibrating alarm and a bright multi-directional visual LED alarm light.

Lifetime warranty

The Micro IV carries a lifetime warranty on non-consumable components and two or more years of warranty on most sensors. Select sensors such as O2, H2S, and CO carry a full three year warranty against failure.

DS220 docking station

The Micro IV is available with a six position fully automatic docking station. The docking station makes bump test and calibration even easier and all maintenance records are stored automatically. The docking station fully test sensor response, alarms and other functionality.

Features

• Highly configurable smart sensor design
• Wide range of sensors including O₂, H₂S, CO, NH₃, SO₂, CL₂, CLO₂, PH₃, NO₂, HCN, HCl, ETO, HF, O₃, NO, H₂, THT and more!
• Full 3-year warranty on O₂, CO and H₂S sensors
• Optional sample draw pump
• Large display with real-time readout
• Event / Datalogging standard
• Programmable ceiling (3), STEL & TWA alarms
• Vibrating Alarm standard
• AutoCal® automatic calibration
• Optional docking station

Standard Accessories

• Micro IV detector
• Specified Sensor
• Alkaline Battery
• Rubber Boot
• Manual

2801-13-002 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-100% LEL (MK 208-1), Toluene (C7H8), Display by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

2801-22-002 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-100% LEL (MK 208-1), Benzene (C6H6), Display by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.