All Products

72-2120-202 Digester Gas Monitor, 100% Volume CH4/1,000 ppm H2S by RKI Instruments

RKI is proud to introduce our Digester Gas Monitor. Gas from waste digesters contains high levels of methane, CO2, and H2S, with little to no oxygen present. The RKI gas monitor checks for all these gases on a cyclic basis. A powerful air aspirator draws a sample from up to 100 feet away. Since digester gas contains high humidity and high H2S, both of which can cause damage to sampling systems, the RKI Digester Gas Monitor is designed to handle these with no damage to the sampling system or sensors. The sample is passed through a series of dirt, dust, and moisture stopping filters, and these filters are automatically purged with fresh air at the end of each cycle.

Measurement time is just 4 minutes, taken at periodic cycles. Cycle time is selectable, with settings for cycle time of 15 minute, 1 hour, 4 hours, 8 hours, or 24 hours. A cycle can also be initiated anytime by pressing a button. After each cycle, the sensors and sampling system are flushed with fresh air so as to minimize corrosion caused by the high H2S content. The system is fault tolerant minimizing the possibility of expensive repairs or downtime.

System integrity is maintained at all times using a flow fail monitoring device which provides a fail alarm and relay if there is ever a problem with the flow system, such as a blockage, or if the air aspirator compressed air supply is removed or interrupted.

The system is housed in a wall mounting NEMA 4X enclosure. The gas readings can be viewed through the enclosure door clear window. Flow meters and filters are easily visible for confirmation of correct flows and operation. The RKI Digester Gas Monitor contains adjustable alarm levels for each gas, and also programmable alarm relays. In addition, the unit provides 4-20mA signals for each gas concentration for connection to an external DCS, PLC, or other site control system. A Modbus output is also available. The outputs are the readings received from the last cycle taken.

Features:

• Corrosion resistant design; Housing designed for extreme environments; Internal construction for extreme samples; Flow system designed to handle corrosive wet samples
• Sample system designed to handle high humidity
• Accurately measures gases with high levels of H2S present
• 100 ft. sample range
• Up to 4 sensors: Methane 0-100% Volume; CO2 0-50% Volume; Oxygen 0-25% Volume; H2S 0-1000 PPM (0-3000 or 0-5000 optional)
• Self draining moisture trap
• Automatic backflush of sampling system
• Long life air aspirator (no moving parts)
• Suitable for inside/outside installations
• NEMA 4X enclosure
• Uses proven RKI technology
• Modular design easy to maintain
• Simple to operate

Industry Applications:

• Wastewater Treatment Digesters
• Biogas Methane
• Animal Farms

*Please note we can only ship RKI products to customers within the United States

MCXL-X000-B-UK GasAlertMicroClip XL Detector, Oxygen (O2) - Black Housing, UK Version (United Kingdom) by BW Technologies

The easy to wear, slim and compact GasAlertMicroClip provides affordable protection from atmospheric gas hazards. For standard operation with features you can count on, opt for the GasAlertMicroClip XT. For extended battery life, especially in cold weather, choose the GasAlertMicroClip XL. Both offer visual compliance at a glance with the flashing, green IntelliFlash™. Easy onebutton operation reduces training time and lets workers focus on the job at hand. For simple, cost-effective management of your records, calibration and bump testing, choose BW's MicroDock II automatic test and calibration system and Fleet Manager II software.

• Easy and comfortable to wear; thin and lightweight
• Easy operation and straightforward training with one-button simplicity
• Easy visual compliance with flashing, green IntelliFlash™
• Easy and cost effective to own

Additional GasAlertMicroClip features:

• Choose the GasAlertMicroClip XL for cold weather performance
• IntelliFlash™ verifies operation and compliance to both the user and supervisor
• Tamper-proof, one button operation
• Powered by a rechargeable lithium polymer battery

Standard features of BW multi-gas products:

• Continuous LCD shows real-time gas concentrations
• Compact and lightweight design makes it comfortable to wear
• Water-resistant
• Simple automatic calibration procedure; compatible with BW MicroDock II automatic test and calibration station
• Full function self-test of sensor, battery status, circuit integrity and audible/visual alarms on start up
• Bright wide-angled visual alarm bars
• Built-in concussion-proof boot
• Multi-language support in English, French, German, Spanish and Portuguese
• Conveniently manage your fleet using Fleet Manager II

Part Number: MCXLX000BUK

PH60 Premium pH Tester by Apera

The Apera Instruments PH60 Tester is the new generation premium pH tester for all kinds of regular aqueous solution's testing, such as hydroponics, aquaculture, pools & spas, water treatment, cooling towers, etc. Features ACCURATE, QUICK & RELIABLE measurements. Besides the regular glass bulb probe, there are 3 other types of replaceable probes for your choice to meet your specific testing needs.

Up to 3 points (4.00, 7.00, 10.01) of Auto Calibration with auto buffer recognition and 0 to 50°C Auto Temperature Compensation (ATC), ±0.01 pH, 0.5°C accuracy with -2.00 to 16.00 pH measuring range, auto recognition and reminders of stable values improves consistency, saving you the trouble of guessing when to manually hold measurement (auto hold function available).

Equipped with a large clear LCD with 3 backlit color (blue for measuring mode, green for calibration mode, red for heads-up), it supports dual display of temp./pH value and indications of completed calibrations (where L/M/H indicate 3 points of calibrations) and stable readings (with a smiley face).

Unique High/Low Value Heads-Up function: the screen will turn red if measurement is higher/lower than a preset value, instantly reminding you of any results that need your attention.

Great value---Comes with a complete kit of premixed calibration solutions (4.00 and 7.00), soaking solutions (3M KCL), calibration bottles, AAA batteries, and a lanyard all in a portable carrying case.

Easy menu setting, customizing your tester's functions according to your needs. Smart self-diagnosis, warning of out-of-range measurement and incorrect calibrations. IP67 waterproof and dustproof, floating on water so you don't have to worry if it falls into water by accident. 2000 hours' continuous operation (without backlit) powered by AAA batteries (with low power warning and auto power off in 8 min if no operation).

The meter is CE certified and comes with a 2-YEAR Warranty (6 months for the probe). The company designs and manufactures scientific analytical instruments like meters and sensors for pH, conductivity, turbidity, and dissolved oxygen for over 25 years, and meets ISO 9001:2008 Standards.

• Easy Auto Calibration with buffer recognition; Auto Temp. Compensation (ATC) ensures accuracy in variant temperatures (0-50.0°C); Accuracy: ±0.01 pH, 0.5°C, Range: -2.00 to 16.00 pH
• 3 types of replaceable probes for your choice, aiming at pH measurements for different substances.
• AUTO recognition of stable values (optional Auto HOLD function available) improves consistency so you don t have to guess when to manually hold measurement
• LARGE CLEAR LCD with 3 backlit color (indicating 3 different modes), dual display of temp./pH, and REMINDERS of completed calibrations and stable readings
• COMPLETE KIT with READY-TO-USE calibration solutions, calibration bottles, storage solutions, AAA batteries, and a lanyard all in a premium portable carrying case

MCXL-X000-B-EU GasAlertMicroClip XL Detector, Oxygen (O2) - Black Housing, EU Version (Europe) by BW Technologies

The easy to wear, slim and compact GasAlertMicroClip provides affordable protection from atmospheric gas hazards. For standard operation with features you can count on, opt for the GasAlertMicroClip XT. For extended battery life, especially in cold weather, choose the GasAlertMicroClip XL. Both offer visual compliance at a glance with the flashing, green IntelliFlash™. Easy onebutton operation reduces training time and lets workers focus on the job at hand. For simple, cost-effective management of your records, calibration and bump testing, choose BW's MicroDock II automatic test and calibration system and Fleet Manager II software.

• Easy and comfortable to wear; thin and lightweight
• Easy operation and straightforward training with one-button simplicity
• Easy visual compliance with flashing, green IntelliFlash™
• Easy and cost effective to own

Additional GasAlertMicroClip features:

• Choose the GasAlertMicroClip XL for cold weather performance
• IntelliFlash™ verifies operation and compliance to both the user and supervisor
• Tamper-proof, one button operation
• Powered by a rechargeable lithium polymer battery

Standard features of BW multi-gas products:

• Continuous LCD shows real-time gas concentrations
• Compact and lightweight design makes it comfortable to wear
• Water-resistant
• Simple automatic calibration procedure; compatible with BW MicroDock II automatic test and calibration station
• Full function self-test of sensor, battery status, circuit integrity and audible/visual alarms on start up
• Bright wide-angled visual alarm bars
• Built-in concussion-proof boot
• Multi-language support in English, French, German, Spanish and Portuguese
• Conveniently manage your fleet using Fleet Manager II

Part Number: MCXLX000BEU

30-0954RK-224 Aspirator Panel for Two Oxygen or Toxic Direct Connect or S2 Transmitters, with Flow Switch by RKI Instruments

Single or dual sensor system is designed to monitor gas atmospheres from extreme conditions with either temperature, moisture, or pressure challenges. A powerful air aspirator can pull a sample from up to 100 feet away. The filtered and conditioned sample gas is then passed across one or two different detectors. Each detector shares a common calibration and compressed air inlet for aspirated flow. This system is fault tolerant removing the need for expensive downtime and maintenance. The sample is diluted with air after the gas sensor and then returned to a common exhaust reducing the danger of potential hazardous gases entering a safe work space.

System integrity is maintained at all times using a flow fail monitoring device which provides a NO contact that activates if the sample line becomes blocked or damaged or if the air supply is removed or interrupted.

The panel can be used with direct-connect (sensors connected to an RKI controller), or with S2 Series, and M2 Series transmitters. All transmitters have a 4-20 mA signal for direct connection to the site DCS, PLC or site control system. If needed, RKI instruments can supply a dedicated Gas Detection Control system to provide local alarms, 4-20 mA output with a wide range of dry contacts, making the system very sophisticated and user friendly.

Integral sample filter included to remove water and dirt, automatic drain type.

RS485 Modbus output options available on the M2 transmitter.

Features:

• Simple to operate
• Long life air aspirator (no moving parts)
• Extreme sample temperatures
• One or two sensors
• Inside/outside location options
• Corrosion resistant construction for extreme environments/samples
• Uses proven RKI technology
• Modular design easy to maintain
• Self draining moisture trap
• Back flush for sample line
• NEMA 4X enclosure options (stainless steel or plastic)

Applications:

• Flammable, oxygen, or toxic monitoring
• Wastewater
• Drinking water plants
• Gas turbine monitoring flammable and CO
• Tunnel monitoring
• Landfill borehole analyses
• Printing press exhaust solvent recovery
• Winery CO2/O2
• Biogas Methane
• Hydrogen Sulfide "H2S" scrubber break through
• Any sample draw gas monitoring application

*Please note we can only ship RKI products to customers within the United States

QRAE PGM-2560 Series Multigas Monitor by RAE Systems

The QRAE 3 is a full featured compact 4-gas monitor that provides detection and monitoring of Oxygen (O2), Combustibles and toxic gases that include Carbon Monoxide (CO), Hydrogen Sulfide (H2S), Sulfure Dioxide (SO2) and Hydrogen Cyanide (HCN) and others.

QRAE 3 can deliver wireless real-time instrument readings and alarm status 24/7. This provides better incident visibility and can improve response time.

Monitor-only configuration includes

• Monitor as specified
• Sensors as specified
• Sampling option as specified
• Calibration adapter (diffusion model only)
• T Calibration tube (pumped model only)
• Internal filters (mounted - diffusion model only)
• External filters (one mounted plus pack of 3 - pumped model only)
• Travel charger cradle with computer cable
• Lithium-ion battery pack
• Universal wall adapter
• CD ROM with ProRAE Studio II
• CD ROM with product content
• Quick Reference Guide

Key Features

• Available in Diffusion or Pumped version
• IP-65/67 water and dust resistant case
• Strong, protective, concussion-proof design
• Real-time gas concentration readings and alarm status enabled by state-of-the-art wireless technology
• Unmistakable five-way local and remote wireless notification of alarm conditions
• Large graphical display icon-driven user interface through intuitive, simple-to-operate two-button user interface
• Multi-language support: 18 languages encoded
• Easy access to pump, sensors, filter and battery compartment

Applications

• Industrial safety
• Oil and gas
• Fireground "Toxic Twins" detection
• Environmental
• Fire and Emergency response
• Chemical
• Pharmaceutical
• Telecommunications

65-2405RKSS S2 Series LEL Transmitter/Detector/XP Stainless Steel J-Box, 4 - 20 mA, Specify Calibration by RKI Instruments

Having a reliable gas sensor is detrimental to the safety and security of workers in potentially unstable work environments. In many cases, the decision to use a gas detection device with a reliable sensor can be the difference between life and death. RKI Instruments understands the reliability of gas sensors should be a top priority for workplace safety managers. Their team of experts works diligently to incorporate the most advanced technologies with the highest industry standards.

For nearly 20 years, RKI Instruments has worked in the gas detection industry. Its line of products leads the industry in innovation and technology. Every year, the company commits to achieving a higher level of productivity and delivering the best gas detection products on the market. With the introduction of their high performing, low cost S2 Sensor Transmitter, RKI is fulfilling that commitment.

S2 Sensor/Transmitter

The RKI S2 Sensors and Transmitters use state of the art sensor technology to detect common gas hazards. Their efficient design and cost effectiveness make them an industry choice for atmospheric monitoring. The sensor transmitters can be used in both indoor and outdoor conditions and are designed to interface with RKI controllers or PLC/DCS systems.

The sensors are available in explosion proof casing for monitoring LEL, H2 specific, oxygen, H2S, CO2, and carbon monoxide. These sensors also have flame arrestors and are approved for use in hazardous environments. The oxygen, H2S, CO, and CO2 sensors are available in non-explosion proof models. The sensors provide highly specific and quick detection and are long lasting. The sensors can be quickly replaced while on the field and do not require any tools.

Explosion proof S2 Sensor/Transmitter

The explosion proof sensors use a variety of detection mechanisms including catalytic for LEL and LEL- H2 specific; metal oxide semiconductor for hydrogen; galvanic cell technology for oxygen; electrochemical for hydrogen sulfide and carbon monoxide; and infrared for carbon dioxide, methane, and hydrocarbons. A hydrogen specific sensor transmitter is not available. Each of these detection methods come with their own measuring range specifications and response times varying from 20 seconds to 45 seconds. These sensors are stainless steel and are housed in a cast aluminum explosion proof J-Box (a stainless steel J-Box is also available).

Non-explosion proof S2 Sensor/Transmitter

The non-explosion proof sensors use galvanic cells for oxygen detection; electrochemical technology for hydrogen sulfide, carbon monoxide, and other toxics; and infrared technology for carbon dioxide detection. The response times vary between 20 seconds and 60 seconds depending on the targeted gas, and the measuring ranges vary as well. These sensors are plastic or aluminum and housed in an explosion proof J-Box.

Accessories

The S2 Sensor/Transmitter has numerous accessories available to meet the individual workplace's needs. Such accessories include calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors or panels, and data loggers.

Each sensor comes standard with a one year warranty for materials and workmanship.

*Please note we can only ship RKI products to customers within the United States

MCXL-X0H0-Y-EU GasAlertMicroClip XL Detector, Oxygen (O2), Hydrogen Sulfide (H2S) - Yellow Housing, EU Version (Europe) by BW Technologies

The easy to wear, slim and compact GasAlertMicroClip provides affordable protection from atmospheric gas hazards. For standard operation with features you can count on, opt for the GasAlertMicroClip XT. For extended battery life, especially in cold weather, choose the GasAlertMicroClip XL. Both offer visual compliance at a glance with the flashing, green IntelliFlash™. Easy onebutton operation reduces training time and lets workers focus on the job at hand. For simple, cost-effective management of your records, calibration and bump testing, choose BW's MicroDock II automatic test and calibration system and Fleet Manager II software.

• Easy and comfortable to wear; thin and lightweight
• Easy operation and straightforward training with one-button simplicity
• Easy visual compliance with flashing, green IntelliFlash™
• Easy and cost effective to own

Additional GasAlertMicroClip features:

• Choose the GasAlertMicroClip XL for cold weather performance
• IntelliFlash™ verifies operation and compliance to both the user and supervisor
• Tamper-proof, one button operation
• Powered by a rechargeable lithium polymer battery

Standard features of BW multi-gas products:

• Continuous LCD shows real-time gas concentrations
• Compact and lightweight design makes it comfortable to wear
• Water-resistant
• Simple automatic calibration procedure; compatible with BW MicroDock II automatic test and calibration station
• Full function self-test of sensor, battery status, circuit integrity and audible/visual alarms on start up
• Bright wide-angled visual alarm bars
• Built-in concussion-proof boot
• Multi-language support in English, French, German, Spanish and Portuguese
• Conveniently manage your fleet using Fleet Manager II

Part Number: MCXLX0H0YEU

MCXL-00H0-Y-OE GasAlertMicroClip XL Detector, Hydrogen Sulfide (H2S) - Yellow Housing, OE Version (Other Regions, 2-pin UK plug) by BW Technologies

The easy to wear, slim and compact GasAlertMicroClip provides affordable protection from atmospheric gas hazards. For standard operation with features you can count on, opt for the GasAlertMicroClip XT. For extended battery life, especially in cold weather, choose the GasAlertMicroClip XL. Both offer visual compliance at a glance with the flashing, green IntelliFlash™. Easy onebutton operation reduces training time and lets workers focus on the job at hand. For simple, cost-effective management of your records, calibration and bump testing, choose BW's MicroDock II automatic test and calibration system and Fleet Manager II software.

• Easy and comfortable to wear; thin and lightweight
• Easy operation and straightforward training with one-button simplicity
• Easy visual compliance with flashing, green IntelliFlash™
• Easy and cost effective to own

Additional GasAlertMicroClip features:

• Choose the GasAlertMicroClip XL for cold weather performance
• IntelliFlash™ verifies operation and compliance to both the user and supervisor
• Tamper-proof, one button operation
• Powered by a rechargeable lithium polymer battery

Standard features of BW multi-gas products:

• Continuous LCD shows real-time gas concentrations
• Compact and lightweight design makes it comfortable to wear
• Water-resistant
• Simple automatic calibration procedure; compatible with BW MicroDock II automatic test and calibration station
• Full function self-test of sensor, battery status, circuit integrity and audible/visual alarms on start up
• Bright wide-angled visual alarm bars
• Built-in concussion-proof boot
• Multi-language support in English, French, German, Spanish and Portuguese
• Conveniently manage your fleet using Fleet Manager II

Part Number: MCXL00H0YOE

G460-11-02-70-00-14 G460 Multi-Gas Detector with Alkaline Smart Pump and Alkaline Battery, O2, Catalytic Combustion LEL Sensor, H2S, PID by GfG

For over 50 years, GfG Instrumentation has worked to develop the most reliable and effective equipment for gas detection and measurement technology. Developed by a team of highly experienced scientists and specially trained engineers, GfG products are high quality reliable instruments designed to meet the unique needs of potentially hazardous worksite. With the introduction of the G460 Multi-Gas Detector, GfG Instrumentation is continuing the trend.

G460 Multi-Gas Detector

The G460 Multi-Gas Detector is a compact and robust system with the capabilities of detecting up to six different gases and simultaneously displaying the readings. The portable detector features a user friendly and intuitive interface to simplify the day to day operations.

Ease of Use

For typical daily operations, the G460 Multi-Gas Detector operates with a single button. The complete user interface can provide access to advanced setup options with three buttons. The unit also features easy calibration operation. Simply attach the calibration adapter and apply gas. The G460 will automatically perform the appropriate adjustments. The detector will then store the dates of the three most recent calibrations for each sensor.

The G460 also features a large easy to read tricolor display which uses a color code to indicate the alarm severity. From green to orange to red, the tricolor display is intuitive and incredibly user friendly. The display feature can also flip or zoom with the touch of a button. The G460 multi-faceted alarm system also includes an ultra loud audible buzzer at 103 dB, a standard vibration mechanism, and 360 bright LED alerts (the LED alerts can also be equipped to function as flashlights). This multi-faceted system is sure to alert users and those nearby of the potential hazardous conditions. For smooth and continuous operations, the G460 Multi-Gas Detector uses interchangeable alkaline and rechargeable battery packs that provide up to 25 hours of continuous operation. Using a drop in cradle charger, the rechargeable pack can completely recharge in less than 4 hours.

G460 Multi-Gas Detector Features

The G460 Multi-Gas Detector features a motorized pump with a built-in diffusion or sample draw mode switch. The hose is easily attachable and can draw from 100 feet away. The hose is powered by its own battery pack that provides 20 hours of continuous operation. The multi-gas detector also features the widest range of sensors on the market. The compatible long lasting (and interchangeable) smart sensors include LEL, SO2, O2, H2, H2S, NO, CO, O3, HF, NH3, CIO2, CI2, PH3, ETO, HCN, and NO2. Users can purchase additional sensors to help customize the unit such as infrared sensors for the measurement of CO2 and photoionization sensors for volatile organic chemical hazards. The G460 has standard data logging capabilities that store up to 55 hours of the most recent activities. Alarm activations gas thresholds and stored permanently in the internal memory. Employers can download all internal information to generate reports and monitor results.

G460-11-01-70-00-40 G460 Multi-Gas Detector With NiMH Battery with Flashlights, O2, LEL, CO, PID (0.5-2000) by GfG

For over 50 years, GfG Instrumentation has worked to develop the most reliable and effective equipment for gas detection and measurement technology. Developed by a team of highly experienced scientists and specially trained engineers, GfG products are high quality reliable instruments designed to meet the unique needs of potentially hazardous worksite. With the introduction of the G460 Multi-Gas Detector, GfG Instrumentation is continuing the trend.

G460 Multi-Gas Detector

The G460 Multi-Gas Detector is a compact and robust system with the capabilities of detecting up to six different gases and simultaneously displaying the readings. The portable detector features a user friendly and intuitive interface to simplify the day to day operations.

Ease of Use

For typical daily operations, the G460 Multi-Gas Detector operates with a single button. The complete user interface can provide access to advanced setup options with three buttons. The unit also features easy calibration operation. Simply attach the calibration adapter and apply gas. The G460 will automatically perform the appropriate adjustments. The detector will then store the dates of the three most recent calibrations for each sensor.

The G460 also features a large easy to read tricolor display which uses a color code to indicate the alarm severity. From green to orange to red, the tricolor display is intuitive and incredibly user friendly. The display feature can also flip or zoom with the touch of a button. The G460 multi-faceted alarm system also includes an ultra loud audible buzzer at 103 dB, a standard vibration mechanism, and 360 bright LED alerts (the LED alerts can also be equipped to function as flashlights). This multi-faceted system is sure to alert users and those nearby of the potential hazardous conditions. For smooth and continuous operations, the G460 Multi-Gas Detector uses interchangeable alkaline and rechargeable battery packs that provide up to 25 hours of continuous operation. Using a drop in cradle charger, the rechargeable pack can completely recharge in less than 4 hours.

G460 Multi-Gas Detector Features

The G460 Multi-Gas Detector features a motorized pump with a built-in diffusion or sample draw mode switch. The hose is easily attachable and can draw from 100 feet away. The hose is powered by its own battery pack that provides 20 hours of continuous operation. The multi-gas detector also features the widest range of sensors on the market. The compatible long lasting (and interchangeable) smart sensors include LEL, SO2, O2, H2, H2S, NO, CO, O3, HF, NH3, CIO2, CI2, PH3, ETO, HCN, and NO2. Users can purchase additional sensors to help customize the unit such as infrared sensors for the measurement of CO2 and photoionization sensors for volatile organic chemical hazards. The G460 has standard data logging capabilities that store up to 55 hours of the most recent activities. Alarm activations gas thresholds and stored permanently in the internal memory. Employers can download all internal information to generate reports and monitor results.

2200-005W GMA 200-MW16 Controller, Configured for 5 Measuring Points, Supply Voltage 24 V/DC, without Power Supply by GfG

The GMA 200-MW is our most flexible and advanced gas detection system controller. The design of the GMA 200-MW ensures simple and clearly structured operation in industrial and commercial applications. The system can be configured for control of any combination of GfG gas transmitters for the measurement of an extremely wide range of toxic and combustible gases and vapors.

Flexible modular design

Each GMA 200-MW module can control up to 16 individual gas transmitters (sensors). The self-contained, IP-65 wall-mounted housing facilitates cost-effective and space-saving installation. GMA 200-MW systems are scalable, and easy to expand by adding additional controller and relay modules. Optional gateway modules allow control via remote or touch-screen computer interface.

Easy to configure

Easy-to-use, menu driven GMA 200-MW software allows configuration of sensor type, gas type, measuring point designations, units of measurement, calibration curves, and function of the comprehensive and fully programmable relays. Up to three individual or specified alarm thresholds can be programmed for each measuring point. The GMA 200-MW continuously evaluates the analog input signals of the connected detectors.

Integrated relays

GMA 200-MW systems include comprehensive and fully programmable relays. Each controller is equipped with 8 internal relays. Menu-driven software allows easy assignment of measuring points to relays, single or multiple alarms per point, alarm thresholds, configuration of collective or group alarms, zoning, fault messages and voting functions.

Relay modules

GMA 200-RW relay modules are housed in easy to install IP-65 wall mounted enclosures. Each relay module provides an additional 16 freely configurable relays. A total of four additional relay modules (for 64 additional relays) can be managed by the same GMA 200-MW system. Digital connection with the GMA 200-MW controller allows remote positioning of the relay module wherever it makes the most sense, substantially reducing cabling and installation costs.

Remote terminal displays

Relay modules are available with or without an integral display for readings and system information, making it easy to add a remote terminal wherever needed.

Optional Fieldbus-Gateways

Optional gateway modules allow integration of the GMA 200-MW system into existing company networks based on TCP/IP, Process Field Bus or Process Field Network protocols. Monitoring and system performance data are easily exported for viewing or analysis. A wifi interface can be added to the gateway to allow wireless connection with a touch screen Windows® computer or smart-phone to display or access system information.

GMA 200 power options

GMA 200-MW power options include traditional voltage inputs (2 x 24 V DC, 20-30 V), as well as operation via a redundant, uninterruptible power supply (UPS), ensuring continued operation of the gas warning system even during a power outage.

Integral alarms

The GMA 200-MW includes built-in bright LED strobe light and loud audible alarms.

LED indicator lights

The status of the GMA 200-MW system (including operation, fault, service, alarm and relay status) is shown via LEDs. Individual LED indicators identify the type and severity of the alarm condition, (FLT, AL1, AL2, AL3), and any relays activated by the condition, (R1 through R8).

Datalogging standard

Measured values, mean values, alarm events and faults are permanently stored on a microSD memory card.

Graphical display

Currently measured values are displayed on a backlit, graphical LCD. In the event of an alarm the display changes color from green to red, and highlights the affected channels.

Five buttons enable operation at the GMA 200-MW controller. The main functions of the keyboard are the acknowledgement of alarms and the menu-driven operation. Information on the status of the controller, detector and the relays can be retrieved in the operating menu.

Operation via keypad

Operation of the GMA 200-MW is through easy-to-use menus, and a simple 5 button interface for alarm acknowledgement, and viewing information on the status of the gas warning system, detectors and relays. The intuitive push-button controls make it easy to navigate through additional screens of information. The integrated display enables the reading of alarm levels through the controller LCD for easy hazard assessment.

Configuration

A built-in USB port in the GMA 200-MW is used for connection to the configuration software. GMA 200-MW systems connected through a Fieldbus gateway can be remotely connected with a GfG factory service center for configuration, diagnostic or service evaluation.

Easy and convenient service

GfG offers full after-the-sale commissioning and field service support.

Additional modules available in IP-65 wall-mounting housings

• External relay module: GMA 200-RW
• Independent power supply: GMA 200-UPS
• Continuous, motorized pump sampling unit: GMA 200-ASV
• Fieldbus gateway: GMA 200-GW

Features

• Advanced and flexible controller for combustible, O₂ and toxic gas
• IP-65 wall-mounting housing, with integral audible and LED alarms
• Flexible, reliable and economic
• Up to 16 transmitters per GMA 200-MW controller in any combination
• Freely programmable relays
• Clearly structured, easy-to-use push-button interface
• Backlit graphic LCD changes color to indicate alarm
• Connect to other measurement devices with 4-20 mA output

73-1020RK-02 PS 2 Single Point Stand Alone Monitor for PPM Detection, 24 VDC Powered by RKI Instruments

A perfect low cost solution for hydrogen detection in battery rooms, or for LEL or PPM level detection of a variety of flammable or solvent vapors in general industry.

The Model PS 2 is a multipurpose gas monitor utilizing a MOS (metal oxide sensor) for long lasting and low maintenance detection at the LEL or PPM levels of many gases or vapors. The PS 2 has two alarm levels for increasing gas or vapor levels, at the PPM level for detection of many solvent vapors, or for LEL level detection of flammable vapors. Inquire at the factory for your specific requirement. Each alarm level activates a 12 amp relay inside the unit, and terminals are provided for wiring the relay to activate an external alarm device or some other device such as a ventilation fan.

This stand alone unit is housed in a durable plastic enclosure with flanges provided for wall mounting and is designed with easy access wiring hubs on the bottom of the unit. The front of the PS 2 contains three lights; Pilot, Alarm 1, and Alarm 2. An internal audible alarm (85 db) activates in a gas alarm condition.

The standard PS 2 is supplied with the gas sensor located on the end of a 30 foot cable (other cable lengths are also available). Each unit is powered by 115 VAC standard or 24 VDC as standard (48 VDC versions optional), and the AC version comes complete with a 6' power cord.

Features

• LEL or PPM detection ranges available for many gases
• 2 alarm levels
• Stand alone system
• Input voltages: 115 VAC standard, 24 VDC or 48 VDC (optional)
• Audible and visual alarms
• Compact design
• Simple installation
• AC version equipped with power cord
• Relay contacts rated 12A @ 115 VAC
• Low maintenance

Industry Applications

• Battery storage locations
• Petrochemical plants
• Refineries
• Water & wastewater treatment plants
• Degreasers
• Gas, telephone, & electric utilities
• Manufacturing facilities
• Steel
• Automotive
• HVAC

*Please note we can only ship RKI products to customers within the United States

72-5543RK Eagle Portable Monitor for LEL & PPM/O2/CO/HCl/SO2 with External H2S Scrubber by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

329 Calibratable Water Resistant Digital Pocket Thermometer with Contact Tip (No Sheath) by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Field calibrateable to ±2°F
• Easy-to-read LCD
• Data Hold for hard to reach areas
• Penetration tip
• Auto off
• 3.1 mm stem for fast response
• 4.9 inch stem for insertion in liquids and semi-solids
• IP Rating IP67
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

2200-004W GMA 200-MW16 Controller, Configured for 4 Measuring Points, Supply Voltage 24 V/DC, without Power Supply by GfG

The GMA 200-MW is our most flexible and advanced gas detection system controller. The design of the GMA 200-MW ensures simple and clearly structured operation in industrial and commercial applications. The system can be configured for control of any combination of GfG gas transmitters for the measurement of an extremely wide range of toxic and combustible gases and vapors.

Flexible modular design

Each GMA 200-MW module can control up to 16 individual gas transmitters (sensors). The self-contained, IP-65 wall-mounted housing facilitates cost-effective and space-saving installation. GMA 200-MW systems are scalable, and easy to expand by adding additional controller and relay modules. Optional gateway modules allow control via remote or touch-screen computer interface.

Easy to configure

Easy-to-use, menu driven GMA 200-MW software allows configuration of sensor type, gas type, measuring point designations, units of measurement, calibration curves, and function of the comprehensive and fully programmable relays. Up to three individual or specified alarm thresholds can be programmed for each measuring point. The GMA 200-MW continuously evaluates the analog input signals of the connected detectors.

Integrated relays

GMA 200-MW systems include comprehensive and fully programmable relays. Each controller is equipped with 8 internal relays. Menu-driven software allows easy assignment of measuring points to relays, single or multiple alarms per point, alarm thresholds, configuration of collective or group alarms, zoning, fault messages and voting functions.

Relay modules

GMA 200-RW relay modules are housed in easy to install IP-65 wall mounted enclosures. Each relay module provides an additional 16 freely configurable relays. A total of four additional relay modules (for 64 additional relays) can be managed by the same GMA 200-MW system. Digital connection with the GMA 200-MW controller allows remote positioning of the relay module wherever it makes the most sense, substantially reducing cabling and installation costs.

Remote terminal displays

Relay modules are available with or without an integral display for readings and system information, making it easy to add a remote terminal wherever needed.

Optional Fieldbus-Gateways

Optional gateway modules allow integration of the GMA 200-MW system into existing company networks based on TCP/IP, Process Field Bus or Process Field Network protocols. Monitoring and system performance data are easily exported for viewing or analysis. A wifi interface can be added to the gateway to allow wireless connection with a touch screen Windows® computer or smart-phone to display or access system information.

GMA 200 power options

GMA 200-MW power options include traditional voltage inputs (2 x 24 V DC, 20-30 V), as well as operation via a redundant, uninterruptible power supply (UPS), ensuring continued operation of the gas warning system even during a power outage.

Integral alarms

The GMA 200-MW includes built-in bright LED strobe light and loud audible alarms.

LED indicator lights

The status of the GMA 200-MW system (including operation, fault, service, alarm and relay status) is shown via LEDs. Individual LED indicators identify the type and severity of the alarm condition, (FLT, AL1, AL2, AL3), and any relays activated by the condition, (R1 through R8).

Datalogging standard

Measured values, mean values, alarm events and faults are permanently stored on a microSD memory card.

Graphical display

Currently measured values are displayed on a backlit, graphical LCD. In the event of an alarm the display changes color from green to red, and highlights the affected channels.

Five buttons enable operation at the GMA 200-MW controller. The main functions of the keyboard are the acknowledgement of alarms and the menu-driven operation. Information on the status of the controller, detector and the relays can be retrieved in the operating menu.

Operation via keypad

Operation of the GMA 200-MW is through easy-to-use menus, and a simple 5 button interface for alarm acknowledgement, and viewing information on the status of the gas warning system, detectors and relays. The intuitive push-button controls make it easy to navigate through additional screens of information. The integrated display enables the reading of alarm levels through the controller LCD for easy hazard assessment.

Configuration

A built-in USB port in the GMA 200-MW is used for connection to the configuration software. GMA 200-MW systems connected through a Fieldbus gateway can be remotely connected with a GfG factory service center for configuration, diagnostic or service evaluation.

Easy and convenient service

GfG offers full after-the-sale commissioning and field service support.

Additional modules available in IP-65 wall-mounting housings

• External relay module: GMA 200-RW
• Independent power supply: GMA 200-UPS
• Continuous, motorized pump sampling unit: GMA 200-ASV
• Fieldbus gateway: GMA 200-GW

Features

• Advanced and flexible controller for combustible, O₂ and toxic gas
• IP-65 wall-mounting housing, with integral audible and LED alarms
• Flexible, reliable and economic
• Up to 16 transmitters per GMA 200-MW controller in any combination
• Freely programmable relays
• Clearly structured, easy-to-use push-button interface
• Backlit graphic LCD changes color to indicate alarm
• Connect to other measurement devices with 4-20 mA output

1010A Indoor Air Quality Meter by Test Products International

Measure ambient CO2, temperature, relative humidity, dew point, wet bulb, CO, and calculate percentage outside air. The TPI 1010A Indoor Air Quality (IAQ) Meter is a state of the art, easy to use tester designed to provide you with the necessary measurements to monitor and make adjustments to air handling devices.

The 1010A IAQ meter uses state of the art sensors to measure humidity, carbon dioxide (CO2), and temperature. The instrument is ruggedly constructed and comes with a 3 Year unit and 2 Year sensor Guarantee.

Features

• Calculate percent outside air to maintain acceptable CO2 levels in buildings and work spaces
• Measure and display Carbon Dioxide (CO2) and Carbon Monoxide
• Measure ambient air temperature
• Measure relative humidity, dew point and wet bulb
• Log up to 10,000 readings in 1 second to 1 hour intervals
• Download to a computer using the A368 USB cable
• Print via I/R to optional printer (Model A740)

Applications

• Check ambient CO and CO2 levels in work and living spaces
• Monitor results of air control systems
• Ambient air temperature and humidity
• Test dew point and wet bulb humidity

Standard Accessories

• TPI 1010A Instrument
• Protective Rubber Boot (A800)
• Soft Carrying Case (A921)
• USB Cable & Software (A803)
• Instruction Manual

Optional Accessories

• Power adapter / Battery eliminator (A804)
• Magnetic strap kit to hang meter (A127)
• Boot hook to hang meter (A103)
• Replacement Software only (A802)
• Replacement USB cable only (A801)

pH600-BOX pH Economical Pocket Tester with 1 Point Manual Calibration by Milwaukee

Milwaukee's economical testers are easy-to-use and low cost instruments to measure quick and reliable pH, EC or TDS values.

Measuring electrical conductivity is the best way of checking the amount of salt or dissolved solids (TDS) in water. Milwaukee provides you with a range of pocket testers that will allow you to measure from very low to very high conductivity solutions.

All EC/TDS testers compensate for the temperature variance automatically.

The pH600 is a pH tester can be used in many different applications and is considered an excellent starter unit for digital pH measurement. The calibration procedure is very simple and fast. This tester has 1 point manual calibration, ±0.1 pH accuracy and a range of 0.0 to 14.0 pH. The pH600 is supplied in a snap over "oyster shell" plastic packaging complete with calibration screwdriver, 20 ml of 7.01 calibration solution, batteries and instructions.

10076695 Altair QuickCheck Automated Test Station - Manual Regulator, NH3 by MSA

When working with hazardous substances or in potentially dangerous settings, worksites and users need to feel that safety is a top priority. MSA s Altair gas detectors and MSA s Altair QuickCheck Stations provide that sense of security as MSA products prioritize safety and reliability above all else. The QuickCheck Station is specially adapted for unique working conditions with its compatibility with other Altair products, easy to read test indicators, internal test record retention, and lightweight portability.

Features

The Altair QuickCheck Station tests Altair products for gas detection effectiveness and alarm functioning. The QuickCheck Station is compatible with the Altair and Altair Pro Single-Gas Detectors. The unit s easy to read displays and test indicator settings reduce the risk of mistaken test results. As Altair gas detection devices develop to meet industry needs, Altair s QuickCheck Station versions will be available with the ability to test the upcoming exotic gas variations.

The Altair QuickCheck Station has a variety of key features. The unit is designed to test Altair gas detectors sequentially for visual alarm activation, vibrating alarm activation, audible alarm activation and verification, and sensor gas response. The QuickCheck Station will indicate an easy to read pass or fail of the unit being tested. Users need only to set the gas detection instrument into the test station and manually press the TEST button. The test station records the date, time, and test results internally. The testing station can store up to 25 individual tests and results, and the Altair Pro Detector can store up to 50 individual tests and results.

Easy to read

The testing device also notifies users of the testing progress with a variety of easy to understand visual LED indicators. When the device is in the process of testing the gas detector, the device will flash an amber light. A solid red light indicates that the gas detector failed the test, and a green light indicates the detector passed the test. If a device is left mounted to the QuickCheck Station, the station will display a checkmark for 24 hours following a passed test.

Portability

The QuickCheck Station is lightweight at approximately 8.6 ounces (or 245 grams) and easily portable at approximately 2 inches in height, 4 ¾ inches in width, and 6 inches long. Typical testing time for the Altair QuickCheck Station is under 30 seconds and can be purchased in both automatic and manual versions. The unit is rated to operate in temperature conditions between 32 and 104 degrees Fahrenheit. The device also operates on 115/230 VAC or 50/60 Hz, and a car accessory power supply is available for additional power supply needs. Users may find a variety of replacement and accessory parts available in North America and internationally.

While Altair QuickCheck Station is the standard for excellence in safety, its cost-efficient production ensures that the unit is affordable and available. With the unit s quick test time of less than 30 seconds, compatibility with other Altair gas detection devices, and easy to read test LED test indicators, Altair QuickCheck Station is an industry leader in safety and reliability.

Xgard Gas Detectors

Crowcon is a global leader in designing and manufacturing gas detection technology and equipment. The company has been in operation for over 40 years and is consistently building upon its products. By integrating modern technology with the demands of the modern workplace, Crowcon has developed a line of gas detection devices and monitors that lead the competition. The Xgard range of gas detectors is a product of Crowcon s successful integration and technological advancements. With a wide range of sensor types and available accessories, the Xgard series is suitable for all worksites and is customizable enough to fit any needs.

Tough and reliable

The Xgard series of fixed point gas detectors is incredibly durable and reliable. The casings and materials, including weatherproof caps, are designed to protect the equipment from the harshest environments. The detectors are made from a variety of materials depending on the model: glass reinforced nylon, aluminum with polyester coating, and 316 stainless steel.

Variety of sensors

The fixed point gas detector offers a wide range of sensors for to suite almost all applications. The Xgard range of gas detectors is available in three models to meet varying worksite needs: flameproof, intrinsically safe, and safe area formats. Additionally, Xgard offers different types of fixed point gas detectors within these three models:

• Xgard Type 1- Intrinsically safe toxic and oxygen gas detectors
• Xgard Type 2- Flameproof toxic and oxygen gas detectors
• Xgard Type 3- Flameproof flammable gas detector
• Xgard Type 4- Flameproof high temperature flammable gas detector
• Xgard Type 5- Flameproof flammable gas detector with 4-20mA output
• Xgard Type 6- Flameproof thermal conductivity type gas detector
• Xsafe- Safe area flammable gas detector

Cost efficient and highly effective

With quick and easy installation and maintenance, the Xgard series is able to keep costs at a minimum. The replacement sensors, for example, are simple to replace by merely plugging them in. The replacement parts are also readily available and compatible with all Xgard models, thereby reducing the amount of required spare parts that are stored in the facility. Additionally, the sensors have two times the typical life spans of similar sensors in the industry. With a 2 year life span, worksites can expect to cut their sensor replacement costs in half. For worksites that require slightly more customization, Crowcon offers compatible accessories for the Xgard series such as sampling applications, remote gassing applications, spray deflectors, sun shields, weatherproof caps, collector cones, flow adapter, and accessories adapter.

Xgard also has flexible installation options. The unit is designed for either wall or ceiling mounts, and users will not need to purchase additional equipment for mounting. For more complex installation needs, users can purchase accessories.

Specifications

Each model is approximately the same size with dimensions of 6.1 x 6.5 x 4.3 inches and weighing approximately 1 or 2 pounds. The battery type, electrical output, and power requirements vary based on the sensor type. For a complete listing of gas sensors, types, and individual specifications, please see the product specifications listing.

*Please note we can only ship RKI products to customers within the United States