All Products

2811-722-002 EC 28 Gas Transmitter with Sensor, Nitrogen Dioxide (NO2), Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

Part Number: 34L-135N-2.5

Part Number: 10L-375

Part Number: 103L-375

Old Part Number: HP101640
New Part Number: H101640PA

10080532 Altair Pro Single-Gas Detector Alternate Set Point Models - Carbon Monoxide (CO) Steel by MSA

When working in settings with hazardous gases or fluctuating oxygen levels, the available gas detection devices can be detrimental to health and safety. Workers in these situations need a gas detection unit that is reliable, accurate, safe, and cost efficient. Altair Pro Single-Gas Detector is built to the superior safety and quality standards of MSA and is available worldwide.

Rough and tough exterior

Design simplicity

Altair Pro Single-Gas Detector standard features

The Altair Pro Single-Gas Detector is also compatible with the Remote Oxygen Detector application. The remote oxygen sensor is designed to be lowered into remote locations by a 10 foot cable and monitor oxygen levels, further reducing unnecessary risk. The Pro Single-Gas Detector is also compatible with many other MSA products. For testing and calibration, the Altair QuickCheck Station provides an easy and cost-efficient way to perform daily tests for gas monitoring and alarm functioning. For more complete and automatic calibration and record-keeping, use the Altair Galaxy Automated Test System.

Specifications

65-2340RK-HCN S2 Series Hydrogen Cyanide (HCN) 0 - 15 ppm Sensor/Transmitter, Non Explosion Proof with J-Box by RKI Instruments

Having a reliable gas sensor is detrimental to the safety and security of workers in potentially unstable work environments. In many cases, the decision to use a gas detection device with a reliable sensor can be the difference between life and death. RKI Instruments understands the reliability of gas sensors should be a top priority for workplace safety managers. Their team of experts works diligently to incorporate the most advanced technologies with the highest industry standards.

For nearly 20 years, RKI Instruments has worked in the gas detection industry. Its line of products leads the industry in innovation and technology. Every year, the company commits to achieving a higher level of productivity and delivering the best gas detection products on the market. With the introduction of their high performing, low cost S2 Sensor Transmitter, RKI is fulfilling that commitment.

S2 Sensor/Transmitter

The RKI S2 Sensors and Transmitters use state of the art sensor technology to detect common gas hazards. Their efficient design and cost effectiveness make them an industry choice for atmospheric monitoring. The sensor transmitters can be used in both indoor and outdoor conditions and are designed to interface with RKI controllers or PLC/DCS systems.

The sensors are available in explosion proof casing for monitoring LEL, H2 specific, oxygen, H2S, CO2, and carbon monoxide. These sensors also have flame arrestors and are approved for use in hazardous environments. The oxygen, H2S, CO, and CO2 sensors are available in non-explosion proof models. The sensors provide highly specific and quick detection and are long lasting. The sensors can be quickly replaced while on the field and do not require any tools.

Explosion proof S2 Sensor/Transmitter

The explosion proof sensors use a variety of detection mechanisms including catalytic for LEL and LEL- H2 specific; metal oxide semiconductor for hydrogen; galvanic cell technology for oxygen; electrochemical for hydrogen sulfide and carbon monoxide; and infrared for carbon dioxide, methane, and hydrocarbons. A hydrogen specific sensor transmitter is not available. Each of these detection methods come with their own measuring range specifications and response times varying from 20 seconds to 45 seconds. These sensors are stainless steel and are housed in a cast aluminum explosion proof J-Box (a stainless steel J-Box is also available).

Non-explosion proof S2 Sensor/Transmitter

The non-explosion proof sensors use galvanic cells for oxygen detection; electrochemical technology for hydrogen sulfide, carbon monoxide, and other toxics; and infrared technology for carbon dioxide detection. The response times vary between 20 seconds and 60 seconds depending on the targeted gas, and the measuring ranges vary as well. These sensors are plastic or aluminum and housed in an explosion proof J-Box.

Accessories

The S2 Sensor/Transmitter has numerous accessories available to meet the individual workplace's needs. Such accessories include calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors or panels, and data loggers.

Each sensor comes standard with a one year warranty for materials and workmanship.

*Please note we can only ship RKI products to customers within the United States

Part Number: J10165000PA

Part Number: M1978

This is the equivalent of the CG2-X-18.0-34 from BW

Part Number: 34LS-161-18

Part Number: 10L-489E

Part Number: P1016.5PA

Are your workers tired of lugging around large, bulky, heavy gas detection equipment? Are you tired of dealing with repeated equipment failures and units that are always in the shop?

• Available in CO, H2S, O2, LEL configurations
• CO, H2S, O2 models run for 3000 hours on alkaline batteries
• LEL model runs for 16 hours
• 2 year warranty
• Small and Lightweight
• High Quality and Low Cost
• Peak, STEL, and TWA alarms
Now both of these problems are a thing of the past. The 01 series are single gas monitors that are exceptionally easy to operate, with unmatched reliability. Simply install the batteries and the units are ready to operate. No complicated set up, and no hassles. Workers will be protected with three levels of alarms. Audible, Visual, and Vibration will make sure users are alerted to a dangerous condition no matter what the environment is. For example if a worker is in a particularly noisy environment they may not hear the audible alarm but they will feel the vibration and see the bright LED visual alarms. The alarms are user adjustable and can be set to any level to meet your particular situation, but come defaulted to OSHA recommended set point levels.