All Products

481028 Test Strips: Chlorine Dioxide, 0 - 1.6 ppm by AquaPhoenix

Convenient and simple way of testing chlorine dioxide levels in sanitized water.
0-1.6ppm, 50 strips

Increments of 0.1, 0.2, 0.4, 0.6, 0.8, 1, 1.2, 1.4, 1.6

WD-35625-16 Food TempTestr Mark-I IR Thermometer, with NIST Traceable Certificate of Calibration by Digi-Sense

Ensure your food is at the proper temperature without contamination worries!

Our TempTestr IR Food model is optimized for the food preparation industry. It offers ±1%/1°C (2°F) accuracy in the HACCP critical temperature range of 0 to 60°C (32 to 150°F). This tester s high spectral response lets you take readings through steam. Laser sighting lets you pinpoint your exact target.

• Offers high ±1°C accuracy at HACCP critical temperature ranges
• Infrared temperature measurement provides safe, noncontact readings
• Laser sighting pinpoints your exact target
• °F/°C selectable
• Simple one-handed operation just point and press button! Extremely rapid response time 1/2 second for 95% response

WD-35820-21 Industrial Conductivity Cell, 10 ft Cable, 3/4 MNPT Threaded Housing, Epoxy Body, Graphite Sensor, K= 0.1 (Use with CON 100, CON 200, CON 1000, and RES 1000 controllers) by Oakton

Feature built-in temperature compensation

• Designed for continuous in-line monitoring
• Feature stripped ends for easy wiring

Choose from three different cell constants:

• K = 1.0 for midrange conductivity measurements.
• K = 10.0 for high conductivity measurements (near or above 20 mS)
• K = 0.1 for low conductivity measurements (near or below 20 µS)
• K = 0.01 for resistivity measurements (at or below 2 µS)

Install these rugged cells in a pipeline, or submerse in a tank.

Dimensions: 142 mm L x 12 mm dia. Shpg wt 0.5 lb.

93575 LensPen Optics Cleaning Tool by Celestron

How many times has dust or lint on your eyepiece or telescope ruined an observing session? One innocent-looking strand of hair strewn across the lens in your photos or astroimages can take hours of clean-up in a photo-editing program, and a greasy thumbprint or smudge on the optics can send an otherwise perfect image to the trash. Enter the Celestron LensPen, a dual function optical cleaning tool that is small and lightweight enough to stay in your telescope accessory case or camera bag so it will always be there when you need it.

The LensPen is two cleaning tools in one. One end contains a soft brush for removing dust and other particulates from any optical surface. The opposite end of the LensPen will handle the smudges and spots that cannot be brushed away. This tool has a special cleaning tip that works without the need for liquids, so it will never dry out. A cap protects the smudge removal tool when not in use, while the brush retracts safely inside the LensPen.

When cleaning optics, it is always best to use the brush first, even if you think it unnecessary. Carefully brush the entire surface, and when you are done, inspect your work. If you find any smears or spots, use the cleaning element to remove them, using a light touch.

The Celestron LensPen is a great tool for all of your optical equipment, including eyepieces, telescopes, spotting scopes, binoculars, microscopes, cameras, lenses, and more.

• Keep your optics clean with the innovative LensPen
• Use the soft retractable brush for removing loose particles & dust
• Clean smudges, fingerprints, pollen, and other sticky substances from the optics with the special cleaning element.
• No liquids are used...nothing to spill or dry out.
• The LensPen is safe and easy-to-use. Keep one handy for all your optics!

6130-2121 MGD-100 Gas Detection System, VOC: 0 - 2,000 ppm, 2 Sensors, 2 Alarms, IP66 Housing, 110 VAC by Bacharach

Bacharach's MGD-100 Series is a robust and scalable gas detection system used for reliable real-time monitoring of refrigerant, combustible, and toxic gases. It's a stand-alone system that alarms when pre-set thresholds are exceeded. The MGD-100's alarms are monitored by a centralized controller, which can alert personnel of potential hazardous conditions via an onboard buzzer and LED alarm indicators.

MGD-100 Systems can be configured from single-sensor, one-alarm level systems to larger scale systems consisting of 6 sensors with 2 alarm levels. This flexibility allows the platform to be used for both small and large systems.

Ideal for Chiller Rooms, Supermarkets, Brewing and Bottling Facilities, Industrial Refrigeration, Arenas, Food Storage and Processing Facilities.

Features & Benefits:

• Stand-alone, out-of-the-box solution with quick and easy installation - the most cost-effective system available.
• Fast-response sensors detect leaks quickly, which minimize refrigerant gas usage and environmental impact.
• Infrared (NDIR) CO2 detection
• Long-life semiconductor sensors for detection of all refrigerants, ammonia, halocarbons, combustibles & VOCs
• Robust design allows units to be placed directly in areas where detection is needed.
• Available in a variety of housings, including IP66 and duct mount.
• Select from 1, 2, 4 or 6 remote sensors and 1 or 2 pre-set alarm levels, which can be connected to BMS systems.

3806-050 EC 38 Fixed Transmitter with Nitrogen Dioxide (NO₂) Sensor, 0.1 ppm Resolution, 0 - 50.0 ppm Range by GfG

The EC 38 transmitter uses advanced technology for the detection of toxic gases and oxygen levels. It is available in the standard version with horn strobe or with a stack light. This monitor has a NEMA 4X enclosure that makes the EC 38 suitable for the harshest environments.

Simple and effective

Once you power up the units, they will accurately display values on the large LCD and transmit a linear 4-20 mA signal to a GfG controller. Autocal® automatic calibration and maintenance is done effortlessly through push buttons. Smart sensors allow the user to easily change ranges or gas types in the field without a need for additional programming.

• Advanced transmitter for oxygen and a wide selection of toxic gases
• 24 VDC
• Available with stack light or standard version with horn strobe
• AutoCal® automatic calibration
• Alarm relays standard (low, high and fault)
• Linear 4-20 mA output signal
• NEMA 4X housing

M5-X0M0-R-D-D-Y-N-00 Gas Alert Micro 5 (O2,CO, Rechargeable battery, Diffusion, Yellow - NA) by BW Technologies

The GasAlertMicro 5 Series is the most customizable gas monitoring series on the market. With an extensive selection of models, user options, and instrument settings, this multi-gas detector series is an industry leader. BW Technologies by Honeywell recognizes that not all worksites can operate with a one size fits all model of gas detection devices. With the introduction of the GasAlertMicro 5 Series multi-gas detectors, worksites, managers, and users can utilize the customizable features to ensure that the instrument meets their specific worksite needs.

GasAlertMicro 5 Series models

This multi-gas monitor series is available in several models: the standard toxic gas model, a PID model for detection of VOCs, or an IR model for CO2 detection. The unit accurately and reliably identifies up to five atmospheric hazards simultaneously and can rapidly switch from diffusion mode to the optional integrated pump.

Each model of GasAlertMicro 5 Series has several distinct features. With the GasAlertMicro 5 Series, the standard toxic gas model, users can monitor several standard gases with a plug in electrochemical cell sensor and catalytic cell sensor and a typical battery life of 20 hours (AA Alkaline rechargeable). The GasAlertMicro 5 PID is standard with several gas detections, a plug in electrochemical cell sensor and photoionization detector, and a battery life of approximately 15 hours (AA Alkaline rechargeable). Finally, the GasAlertMicro 5 IR features specific gas detection ranges, a plug in electrochemical cell sensor, a catalytic cell sensor, and an infrared sensor for carbon dioxide monitoring. This model also has a battery life of approximately 15 and AA Alkaline rechargeable batteries. For more information about available sensor configurations, please contact BW Technologies by Honeywell.

Exclusive features

Each GasAlertMicro 5 Series device features several exclusive features including a triple alarm system, raised glove-friendly buttons, a large easy to read display, stainless steel alligator clip, visual filter inspection, and automatic activation tests. When the unit is activated, the gas detector will automatically test for sensor integrity, circuitry, and battery. This continuous and reliable testing process ensures that the integrity and dependability of the device is never a concern.

BW Technologies by Honeywell also recognizes the unique needs of the various industries with environmental hazards. With each industry anticipating a separate set of possible dangers, the ability to customize safety devices is critical.

Users and worksite managers will be comforted to know their GasAlertMicro 5 series model is fully customizable. Customizable features include STEL intervals, TWA methods, sensor activation, alarms, display settings, record keeping, pumps, combustible gas measurements, start up calibration, backlights, activation modes, calibration levels, daily bump tests, and languages. To protect the integrity of the user settings and the safety of the gas monitoring device, the GasAlertMicro 5 device features a passcode function to prevent unauthorized manipulation of settings.

Accessories

The GasAlertMicro 5 Series is also compatible with BW's MicroDock II automatic test and calibration system. Users may purchase additional accessories to help fully tailor the gas detection unit to their needs. Accessories include an integral pump and battery charger, a confined space kit, a belt holster, and a collapsible sampling probe.

Part Number: M5-00M0-R-D-D-Y-N-00

Vortex 4-Channel Control Panel for Gas and Fire Monitoring

Crowcon Detection Instruments consistently produces the best gas detection and monitoring devices in the industry. Around the globe, companies and workers enjoy higher standards of safety when they purchase and implement a product by Crowcon. With many years of research and development under its belt, Crowcon continuously works to advance its product offerings by utilizing the latest technology in gas detection. The Vortex 12-channel control panel for gas and fire monitoring is one of the most versatile and compatible control panels on the market with its ease of use and ease of customization.

Easy to Use

The Vortex control panel requires very little training. The unit is incredibly easy to use and simple to understand. All of the day to day operations are easily accessible through push buttons on the front panel, and while the display panel continuously shows necessary information, the LEDs only illuminate when a hazard or fault is detected. This allows users to quickly check the conditions with a mere glance. The Vortex is also incredibly easy to service and maintain. Replacement parts simply plug into the unit, and the interior of the panel was designed for easy access for cable termination. The zones within the unit are compartmentalized so that a user may work on one part of the unit without disabling the entire control panel.

Maximum Flexibility

Crowcon understands the economics of efficiency. When designing the Vortex 12-channel control panel, the company worked to create a product that would be optimally compatible with existing equipment and infrastructures. The Vortex can be configured to match any and all site requirements with minimum wiring. The control panel may also be factory set with specific requirements, easing the installation and training process. These settings may be adjusted at any time by a PC using Vortex software. The panel also uses industry standard communication links and can be simply integrated with existing control systems.

Reliable and Safe

The Vortex has been tested for numerous environmental hazards and is rated IP65 for dust and water ingress. To improve safety measures, all of the relays are monitored continuously. In this manner, faults are immediately identified. This helps to protect the integrity of the device and the safety of the users. The unit also continuously monitors its power supply. If power were to fail, the control panel would switch to its internal batteries which are also continuously monitored. For years, Crowcon has developed its reputation for manufacturing safe and reliable gas detection equipment. In turn, the Vortex control panel enjoys some of the highest safety standards in the industry.

Specifications

The Vortex has dimensions of 18.5 x 12 x 6.5 inches. Enclosed in aluminum and plastic, the wall mounted control panel houses up to 12 channels and utilizes IP65 ingress protection. The unit also has datalogging capabilities. The panel displays several indicators:

• Channel number
• Gas reading
• Measurement units
• Power
• Battery status
• Run/hold indication
• Channel test mode
• System fault/integrity
• Color coded visual alarms and audio alarms

0563 4354 435-4 Multifunction Meter with memory, software & integral differential pressure by Testo

The ambient air conditions measuring instrument, for asssessing Indoor Air Quality and tuning and testing VAC systems, stands out on account of its efficient measurement process. The user-friendly measuring instrument has the right measurement engineering for every application and different flow speeds; for example, thermal probes, vane or Pitot tube measurement. Probe-controlled menus and selectable user profiles, e.g. for duct measurement or long-term measurement, ensure the user-friendliest operation possible. The new IAQ probe measures Indoor Air Quality by measuring the CO2 level, air moisture and air temperature. In addition, lux and comfort level probes can be connected to measure draught air. Clear analysis and archiving ensure convenient documentation. Temperature and humidity measurement is built-in in the new thermal probe. The special flow protocol professionally documents duct measurements. It is also possible to connect additional temperature and humidity probes. Readings from up to 3 temperature or humidity probes can be displayed in the measuring instrument; data transmission is by radio, i.e. wireless.

• Instrument memory for 10,000 readings
• PC software for analysis, filing and documentation of measurement data
• IAQ probe, lux probe and comfort level probe
• Thermal probes, vane measurement and built-in differential pressure probe probe for Pitot tube measurement
• Radio probe for temperature and humidity
• Protection class IP54

6201-5151 IAM-100 Gas Detector, Remote Sensor/Faceplate, LPG 0-5000ppm, 110 VAC by Bacharach

The IAM-100 Gas Monitor from Bacharach offers exceptional continuos monitoring performance and flexibility at an economical price. By itself, or integrated into a comprehensive detection system, the IAM-100 is a scalable solution for detecting a variety of refrigerants, combustible gases and VOC gas leaks at the lowest possible cost.

Onboard LEDs illuminate when the sensor is in an alarm state while the unit's audible alarm alerts personnel in the area that levels have exceeded the desired limit. The audible alarm can be muted with the onboard silence switch. Integrated dual relays enable the IAM-100 to shut-off refrigerant or propane supply lines while the second relay can be used as a connection to a building BMS or BAS system.

The IAM-100 is an alarm threshold device. When the range of the sensor is exceeded, the detector will go into alarm. For example, a unit with a 1,000 ppm R-410a sensor will activate its alarm when the detected refrigerant meets or exceeds 1,000 ppm.

Features & Benefits:

• Real-time continuous gas detection that's scalable, reliable and affordable
• Ideal for commercial applications such as hotel rooms, apartments, dorms, hospitals, restaurant kitchens or battery charging rooms
• Detects refrigerants (at ?1,000 or ?10,000 ppm), TVOCs (at ?1,000 ppm), combustible gases and hydrocarbons (at ?5,000 ppm)
• Fast-responding, long-life sensors
• Integrated visual LED and audible alarms
• Two onboard relays to activate shut-off valves, exhaust fans, or connect to a BMS or fire panel
• Remote sensor with aesthetic faceplate available for discreet monitoring in decorative interiors

0699 6446/5 6446 Compressed Air Meter by Testo

The compressed air counters testo 6441 to testo 6444 are designed for the measurement, monitoring and recording of compressed air consumption, and therefore also for the determination of leakages in compressed air systems, consumption-based allocation of costs and the implementation of peak load management. The compressed air counters testo 6441 to testo 6444 record norm volume flow according to the calorimetric principle, which means the measurement procedure is independent of the process pressure and does not cause a permanent pressure drop.

The version testo 6447 offers everything the testo 6446 provides, in addition the removal of the probe under pressure is possible (patented screw fitting). The larger nominal values refer especially to important compressed air pipelines, often the main supply line after preparation.

• Measurement of norm volume flow in the measuring range 6.7 to 27500 m³/h (DN65 to DN350 or 21/2"-10")
• Exchangeable fitting: Probe removal under pressure possible (testo 6447 only)
• Material selectable between galvanized steel and stainless steel
• Highest flexibility thanks to different signal outputs: Analog output 4 to 20 mA (4-wire), Pulse output, 2 switch outputs (parameterizable: consumption or volume flow-dependent, opener, closer, hysteresis, window)
• Built-in totalizer, even without additional analysis unit
• Operating menu with LED display
• Cleanable sensor

Part Number: P197140LM3

*Please note we can only ship RKI products to customers within the United States

72-5206RK Eagle Portable Monitor for O2/B2H6 by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States