All Products

30-0954-2XX Aspirator Panel for Three M2A Transmitters, Specify Gas Combination, with Flow Switch by RKI Instruments

Single or dual sensor system is designed to monitor gas atmospheres from extreme conditions with either temperature or pressure challenges. A powerful air aspirator can pull a sample from up to 100 feet away. The filtered and conditioned sample gas is then passed across one or two different detectors. Each detector shares a common calibration and compressed air inlet for aspirated flow. This system is fault tolerant removing the need for expensive downtimes and maintenance. The sample is diluted with air after gas sensor then returned to a common exhaust reducing the danger of potential hazardous gases entering a safe work space.

System integrity is maintained at all times using a flow fail monitoring device which provides an NO contact that activates if the sample line becomes blocked or damaged or if the air supply is removed or interrupted.

The panel can be used with direct-connect (sensors connected to an RKI controller), or with S, S2 Series, and M2A Series transmitters. All transmitters have a 4-20 mA signal for direct connection to the site DCS, PLC or site control system. If needed, RKI instruments can supply a dedicated Gas Detection Control system to provide local alarms, 4-20 mA output with a wide range of dry contacts, making the system very sophisticated and user friendly.

Integral sample filter included to remove water and dirt, automatic drain type.

RS485 Modbus output options available on the M2A transmitter.

Features

• Simple to operate
• Long life air aspirator (no moving parts)
• Extreme sample temperatures
• One or two sensors
• Inside/outside location options
• Corrosion resistant construction for extreme environments / samples
• Uses proven RKI technology
• Modular design easy to maintain
• Self draining moisture trap
• Back flush for sample line
• NEMA 4X enclosure options (stainless steel or GRP)

Industry Applications

• Flammable, oxygen, or toxic monitoring
• Wastewater
• Drinking water plants
• Gas turbine monitoring flammable and CO
• Tunnel monitoring
• Landfill borehole analyses
• Printing press exhaust solvent recovery
• Winery CO2 / O2
• Biogas Methane
• Hydrogen Sulfide "H2S" scrubber break through

*Please note we can only ship RKI products to customers within the United States

5600-3042 GDX-350 Gas Sensor Transmitter/Monitor, [O2] 0-30%, 3-wire - with Relays and Modbus by Bacharach

Bacharach's new state-of-the-art GDX-350 transmitters, with Smart Sensor technology, provide accurate and continuous detection of toxic, combustible and asphyxiate gases. The full-featured design of the GDX-350 includes a large LCD display, a 4-20 mA interface, programmable alarms, optional relays and a Modbus interface. Exclusive pre-calibrated replacement sensor technology makes occasional maintenance practically effortless. Rugged construction, intrinsic safety capability (in two-wire mode with barrier) and an explosion-proof housing allow the GDX-350 to operate directly in hazardous-rated areas of many industrial environments, delivering reliable, superior-sensing performance to protect human life, equipment and property.

With its large LCD display, the GDX-350 shows gas concentrations, engineering units and bar graphs along with the most recent 30 minutes of trend data. Utilizing the on-board magnetic keypad, users can also navigate through the display to change alarm set points, instrument configurations, or enter into maintenance mode for non-intrusive sensor calibration. For security, menu options also enable the selection of an authorization code to lock critical parameters. Accompanying the LCD display are standard LED alarm indicators that show when low and high alarm conditions are met. An optional relay board is available to provide three 5-amp relays that can be used to drive audible/visual alarms, or activate exhaust fans.

Features & Benefits:

• Pre-calibrated Smart Sensor capability with 'plug-n-play' convenience minimizes maintenance and downtime
• Non-Dispersive Infrared (NDIR), Catalytic Bead and Electrochemical sensor options available
• Can be placed directly in hazardous environments where leaks occur for quick detection and rapid response
• Graphic LCD for real-time monitoring of concentrations
• 4-20 mA, optional Modbus RTU® and wireless interface
• Easily update alarm set points, configurations or maintenance modes using the LCD display
• 30-minute onboard data trend

123-NH3 Gasflag Ammonia, 0-50ppm by Crowcon

Gasflag is a control system for monitoring any 4-20mA flammable, toxic or oxygen gas detector. Gasflag is ideally suited to light industrial or commercial applications such as LPG monitoring on garage forecourts, chlorine detection in swimming pool dosing rooms, or methane detection in boiler rooms.

Gasflag features a loud sounder, bright LED indicators and relays for switching external devices such as audible visual alarms or valves.

Easy and safe to use - Bright alarm annunciator

• Loud internal audible alarm
• Clear sytem intergrity indication

Fully Flexible

• Accepts industry standard 4-20mA inputs
• Multiple units can be daisy chained
• Variable alarm configurations

No hidden costs

• Integral alarm outputs
• Simple installation
• Minimum maintenance
• One button operation

Galaxy GX2 Automated Test System, Altair 4/4X Detector Configuration, 1 Valve / 1 by MSA

MSA is committed to providing the very best in sensor cell technology. From instrument design and manufacturing to datalogging and report generating software, MSA has consistently delivered products designed to optimize workplace safety and take an active approach to advancing jobsite performance. With the new Galaxy GX2 Automated Test System, MSA takes safety and technology to a whole new level.

Advanced MSA Link Pro Software

The MSA Link Pro Software is a state of the art datalogging system that allows users to analyze all data at any time. The software is easy to set up and configure to user specifications. The dashboard will provide alerts on all conditions, gas calibrations, and maintenance information (including expiration warnings). With the software, users can research data, generate reports, and send automatic email exposure alerts. Users can even generate live results or schedule emails for detector activities. Essentially, the datalogging capabilities allow worksite safety managers effectively and efficiently organize all data obtained throughout the entire gas detection fleet.

Simple User Friendly Design

The new Galaxy GX2 Automated Test System was designed with ease of use and simplicity in mind. The test system features an intuitive color touch screen for easy setup and viewing. The touch buttons are large and feature a scrolling screen with pop up test results. Simply place any compatible Galaxy gas detector onto the automated test system and the system will automatically test, calibrate, and charge. The system allows up to 10 devices and 4 cylinder holders. When using RFID-tagged gas cylinders, gas cylinder information is automatically entered into the system, and the onscreen gas cylinder pressure gauge can display multiple cylinder statuses at the same time.

Users can also see the testing and battery status of devices quickly through the colored LED indicators. With the simple time efficient automatic testing, the Galaxy GX2 Automated Test System can save users up to 50% of calibration costs.

Automated Test System Features

The Galaxy GX2 Automated Test System features 18 different languages with easy language setup options. The system is also optimized for use with MSA's high performing X-Cell Sensors. The advanced MSA X-Cell Sensor technology has a long life, quick bump test, fast calibration, and less clear times.

Galaxy GX2 Automated Test System Specifications

The Galaxy GX2 Automated Test System comes standard with pre-configured plugs, barbs, fresh air filters, spare parts kit, power supply and plug, Ethernet cable, and screen protector. MSA also offers nearly two dozen optional accessories that can be used to customize the automatic test system to meet individual workplace needs.

The automatic test system operates on 100-200 VAC (47-63 Hz). The entire unit is approximately 12 inches high and 6.5 inches wide.

The new Galaxy GX2 Automated Test System provides a simple and efficient approach to testing, calibration, and charging. With numerous user features, advanced software, optional accessories, and automatic cost reduction, the automated test system is an automatic choice for workplace safety managers.

WD-35635-10 T-100WL Portable White Light Turbidity Meter Kit by Oakton

The Oakton T-100 series portable turbidity meters feature five calibration points—0 NTU, 20 NTU, 100 NTU, 400 NTU, and 800 NTU. The 0 NTU uses laboratory distilled or deionized water, while the other four calibration points are configured using high molecule polymer standard solutions included in the kits. The meters also include normal and continuous measurement modes, parameter setup, data recall, real-time clock, calibration date check, automatic power off, and low voltage indication. The continuous measure mode allows you to automatically generate average, maximum and minimum measured values in a data storage interface, suitable for sample solutions with rapid settling and continuous measurement changes.

The large TFT color screen displays a blue background for measurement mode, green background for calibration mode, and features operation guides for easy calibration and measurement. Up to 200 sets of data can be stored on the meter. A USB interface cable can transfer this data to your computer for future analysis.

• Auto-ranging from 0 to 1000 NTU (FNU)
• Stores up to 200 sets of data
• Suitable for field use—meets IP67 water-resistant requirements
• Easy to replace tungsten light source
• Meets performance criteria as specified by EPA 180.1 method

Includes

Six 25 x 60 mm sample test cuvettes, five 60-mL polymer standard calibration solutions (0.0, 20, 100, 400, and 800 NTU), 10 mL of silicone oil, microfiber wiping cloth, PCLink software on USB flash drive, hard carrying case, built-in Lithium ion battery, and USB cable with power adapter.

MISC-MP4K-POLY-WUVIRdual-c4 MiScope megapixel MP4K Handheld Digital Microscope includes enhanced optics, 13 megapixel camera, up to 360x variable magnification with built-in white LED lighting, + UV and 2 wavelengths of IR, on/off light switches, USB 3.0 computer interface, set of 4 variable size shims, and Video ToolBox Premier PC software by Zarbeco

Depending on the image size and resolution quality you need, the MiScope Megapixel MP3 and MiScope Megapixel MP4K both have a range of optional tools and accessories. Video ToolBox imaging software is included with both, enabling you to view live images on your computer screen and capture still pictures or movies which can be emailed or later displayed on a computer projector.

MiScope Megapixel MP3 Features

• 10-180x magnification
• View live and capture images on the computer screen
• Portable with a laptop computer, touch-screen, tablet or mobile device
• Optional Extended Field (EF) with up to 2 1/2" view @6-123x
• USB 3.0 (backward compatible with USB 2.0 at slower speed)
• Optional IR and/or UV illumination (Multi-spectral imaging)
• Optional filter set or filter wheel for IR Luminescence imaging
• Includes our Video Toolbox PRO PC Software for capturing still and moving images, time lapse, enhanced measurement, labeling, draw-on features and digital zoom
• Includes varying thickness Ushim set for fixed magnifications
• Optional VTB Premier Software Includes: calibrated overlays, side by side comparisons, edge detection, optional CAD overlay

MiScope Megapixel MP4K Features

• Ultra high resolution lens
• Resolution to 1 micron with up to 400x magnification
• Connects to the USB port of your desktop or laptop computer
• Includes our upgraded Video Toolbox Premier PC Software with all PRO features plus side by side comparison, calibrated overlays, low-light frame averaging, enhanced measurement tools, pixel level adjustment, magnifier window, edge detection, and optional CAD file import/export
• Optional IR and/or UV illumination (Multi-spectral imaging)
• Includes varying thickness Ushim set, for fixed magnifications
• Working distance up to 2.5 inches, for up to a 1.5 inch field of view
• Adjust the slider arm on the side of the MiScope MP4K to simultaneously control focus and zoom
• Frame rate up to 60 frames/second at HD resolution using USB3; 30 frames/second at 4k resolution with barely perceptible lag (dependent on PC performance)

Computer Requirements for MiScope Megapixel MP3

Minimum system requirements: Pentium IV 1.5 GHz or faster, Windows 7/8/10, DirectX 8.1 or greater, USB 2.0 Port (USB 3.0 port suggested), 2+ GB of Free Memory, Video card with 256 MB of video RAM, minimum 1280 x 1024 resolution at 16-bit color (contact Zarbeco for recommended system requirements). MiTools Mac® Software optional. Android™ 4.2 or higher; compatible with third-party app.

Computer Requirements for MiScope Megapixel MP4K

Minimum system requirements: Pentium IV (4th generation or higher) 1.5 GHz or faster, Windows 7/8/10, DirectX 8.1 or greater, USB 2.0 Port (USB 3.0 port suggested), 2+ GB of Free Memory, Video card with 256 MB of video RAM, minimum 1280 x 1024 resolution at 16-bit color (contact Zarbeco for recommended system requirements).

Old Part Number: Z105310MX10
New Part Number: Z105310PM10

For manual gas sampling. Use with appropriate flow plate and sampling tube.

72-5102RK Eagle Portable Monitor for Oxygen (O2), 0-40% Volume by RKI Instruments

The Eagle Portable Monitor can simultaneously detect up to 6 different gases. With over 400 gas monitoring configurations, the unit can detect a wide range of toxic gases. RKI Industries offers long life protection for workplace safety and hazardous jobsites. With a reputation for advanced engineering and state of the art technology, the RKI Industries' Eagle One to Six Gas Portable Monitor is an industry leader in accuracy and affordability.

Features

The Eagle One to Six Gas Portable Monitor is available with a wide variety of exclusive features. The unit is capable of PPM/LEL hydrocarbon detection and for environmental use, has a methane elimination switch. The dual hydrophobic filters (available on some models) ensure quality control. To preserve the integrity and safety of the device, the portable monitor also has an adjustment lockout switch to prevent tampering. For quick and easy testing, the monitor offers autocalibration and single gas calibration.

The Eagle is housed in an ergonomic RFI, EMI, chemical, and weather resistant polycarbonate and polyester enclosure. It can operate in the rain or in 2 inches of water without damage. It features an ergonomically designed top handle to ensure durability.

Accessories and Options

IR Sensors are available for CO2, % LEL CH4 or HC, and % volume CH4 or HC. Each unit also has datalogging capabilities for research, evaluation, and analysis of worksite atmospheres. The unit comes standard with several accessories including a shoulder strap, alkaline batteries, a hydrophobic probe, a 5 foot hose, and an internal hydrophobic filter with most models. Optional accessories can be purchased to fully customize the portable monitor to meet specific needs including a datalogging kit, remote alarms, dilution fitting, Ni-Cad batteries, battery chargers, continuous operation adapter, extra loud buzzer, extension probes, and large internal hydrophobic filter.

Specifications

The Eagle has a battery life of up to 30 hours of continuous operation with alkaline or Ni-cad capability and a sensor life of approximately 2 years. Its standard weight is approximately 5 pounds with dimensions of 10.5 L x 5.9 W x 7 H. The formidable long life pump (with a life of approximately 6,000 hours) reaches up to 125 feet in range with filters and has a low flow pump shut off and alarm. The unit has a response time of up to 30 seconds for most gases, and features a double alarm of audible alerts at 85 dB and visual alerts of dual high intensity LEDs and a flashing display screen.

The display screen is an easy to read 4 x 20 LCD readout. The backlit display sits at the top of the unit for full visibility, and displays the readings and statuses of 4 channels simultaneously.

The portable monitor is rated as intrinsically safe and has a standard 2 year warranty for materials and craftsmanship.

*Please note we can only ship RKI products to customers within the United States

Part Number: X105325PM42

2811-712-002M EC 28 Gas Transmitter with MODBUS, Chlorine Dioxide (ClO2), Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG s proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG s GMA controller.

The EC 28 DAprovides additional bright alarm LEDs and a buzzer avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

059-D311-200 UltraRAE 3000 Portable Handheld Compound-Specific VOC Monitor - 9.8 eV Lamp, Li-Ion / Universal Charger, Accessories Kit, Calibration Kit, Wireless Bluetooth by RAE Systems

The UltraRAE 3000 is the most advanced Compound-Specific Monitor on the market. Its Photoionization Detector's (PID) extended range of 0.05 to 10,000 ppm in VOC mode and 50 ppb to 200 ppm in benzene-specific mode makes it an ideal instrument for applications, from entry pre-screening during refinery and plant maintenance to hazardous material response, marine spill response and refinery down-stream monitoring.

Monitor only includes

• UltraRAE 3000 Monitor, Model PGM-7360
• Wireless communication module built-in
• Datalogging with ProRAE Studio II Package for Windows® XP, Windows® Vista, or Windows® 7
• Travel Charger
• RAE UV lamp and RAE-Sep™ Tubes
• Flex-I-Probe™ and short probe
• External filter
• Red rubber boot
• Alkaline battery adapter
• Lamp-cleaning kit
• Tool kit
• Lithium-ion (Li-Ion) battery with universal AC/DC charger and international plug kit
• Operation CD-ROM
• Operation & Maintenance manual
• Soft leather carrying case

Monitor with Accessories Kit

• Hard transport case with pre-cut foam padding
• Charging/download cradle
• 5 porous metal filters and O-rings
• Organic vapor zeroing kit
• Gas outlet port adapter and tubing

Optional Calibration Kit

• Calibration gas, 34L, as specified
• Calibration regulator and flow controller

Optional Guaranteed Cost of Ownership Program

• 4-year repair and replacement guarantee
• Annual maintenance service

Key Features

• 3-second response in VOC mode or 60 seconds in compound-specific mode
• Extended range up to 10,000 ppm (in VOC mode) with improved linearity
• Built-in humidity sensor
• Automatic temperature-controlled sampling time calculation
• Highly specific readings, combining a 9.8eV UV lamp and RAE-Sep™ benzene tube
• New sampling probe design provides instant tube-breakthrough visibility
• Versatile VOC or Benzene-Specific modes
• Real-time wireless built-in Bluetooth (and optional RAELink3 portable modem) or Mesh Network support
• Integrated RAE Systems Correction Factors list for more than 200 compounds
• Large graphic display
• Multi-language support
• Easy access to lamp, sensor and battery in seconds without tools
• Inexpensive analysis using low-cost RAE-Sep tubes

Application

• Confined space entry pre-screening during refinery and plant maintenance
• Hazardous material response
• Marine spill response
• Refinery down-stream monitoring
• Plant overhaul

G450-11044 G450 Multi Gas Detector, Flashlight Rechargeable Battery with Alkaline Smart Pump, O2, LEL, CO, H2S by GfG

GfG is one of the industry s leading producers of workplace safety products. Their products are safe, reliable, and customizable. Their state of the art research and development facility produces the most advanced products on the market. Additionally, their dedicated team of safety professionals works to ensure that each product can be equipped with customization tools and modifications to ensure that each product can be optimized to meet the most rigorous workplace safety standards. Introducing the G450 Multi-gas Detector, GfG is continuing its legacy as a safety leader.

G450 Multi-gas Detector

The G450 Multi-gas Detector continually measures up to four separate atmospheric gases. In confined spaces, the detector will monitor LEL combustible gas, oxygen, H2S, and CO. The easy to use G450 series of detectors is designed with user friendliness in mind. Many of its most common functions are operated with a single button, and the unit features a fully automatic calibration system. Users need only to attach the adaptor and flow gas to the sensors. The unit s GfG AutoCal system will automatically initiate the calibration sequence and will update the necessary information on the G450 Multi-gas Detector.

Long Battery Life

The G450 Multi-gas Detector also features a long life battery operation that is most efficient for workplace safety. The device has a batter life of up to 25 hours of continuous operation. With alkaline packs, the units are powered by 2 AA batteries, and when placed in the drop in cradle, the rechargeable battery packs can be fully recharged in less than 4 hours. The rechargeable packs have optional flash light LEDs to indicate charge level.

Triple Alarm System

This unit features an elaborate alarm system that is not to be missed. The triple alarm system features a loud audible alarm of 103dB, a vibrating alarm, and bright 360 wrap around LEDs with a colored backlit display for visual alarms. The alarm system ensures that users and those nearby are fully aware of possible environmental hazards. Additionally, the easy to read backlit display will light varying colors from green, orange, and red to intuitively notify users of the severity of the conditions.

Features

The G450 Multi-gas Detector is encased in a dust proof and highly water resistant housing. The housing even contains a built in rubber boot to help protect from regular wear and tear. Each unit is equipped with datalogging capabilities. The datalogger records and internally stores all activity and environmental conditions. Users can download this information to their computers and use it to research, analyze, and evaluate the jobsite environment.

The multi-gas detection system comes standard with a few accessories including a calibration adaptor, a training manual, and a training DVD. The rechargeable devices include the previous accessories and additional drop in cradle chargers and a wall power adaptor. Optional accessories include a datalogging kit, self powered attachable motorized sample pump, spare battery packs, and rechargeable battery packs. The breadth of available accessories helps to ensure that the G450 Multi-gas Detector can be customized to meet the needs of individual work spaces.

XT-XWH0-Y-AU GasAlertMax XT II 3 Gas Detector, Combustible (% LEL), Oxygen (O2), Hydrogen Sulfide (H2S) - Yellow Housing, AU Version (Australia) by BW Technologies

GasAlertMax XT II is the safest and most economical choice for multi-gas detection systems. Utilizing the most advanced technology on the market, the GasAlertMax accurately and reliably monitors up to four hazardous conditions, and offers a simple user friendly device for easy operation. Its standard safety features and compatibility with other instruments ensure that the gas detector is the best instrument for gas monitoring compliance.

GasAlertMax XT II specifications

The lightweight and portable unit is approximately 11.5 ounces, and features the latest technology allowing for a compact design. With an operational temperature range of -4 to 122 degrees Fahrenheit, the monitor is designed to function effectively in many harsh conditions. The cautionary yellow outer shell helps to ensure that the gas detector is carried with the user not left onsite. Additionally, the durable casing is resistant to water and features a built-in concussion proof boot.

Triple alarm system

The GasAlertMax XT II features a triple alarm system designed to alert users of potentially hazardous conditions. When the gas sensors detect specified levels of H2S, CO, O2, or combustible gases, the instrument will begin the triple alarm alert and notify users and those nearby. The device indicates these dangers with a vibrating alarm, an ultra bright visual alarm, and an audible alarm of over 95 decibels. The alarms are also designed to alert users of administrative needs such as battery replacement.

GasAlertMax XT II features

The GasAlertMax XT II has multi-language support features in English, French, Spanish, German, and Portuguese. The gas detector also has state of the art block detection with semi-conductor pressure sensor, and standard data and event logging. Accessories such as the belt holster, multi-unit cradle charger, and concussion proof boot are also available.

Upon activation, the unit will automatically test sensors, pumps, battery, and circuitry. For additional test and calibration, the GasAlertMax XT II is compatible with the MicroDock II automated test and calibration system and Fleet Manager II. Improving on its functionality, the unit is customizable. Users can change options for forced calibration and tests, safety locks, alarm setpoints, safe display mode, language choices, start-up message, and more.

The easy to read LCD screen displays continuous information about real-time gas concentrations and alarms. To maintain simplicity and ease of use, the GasAlertMax XT II also features a user and glove friendly one touch button for operation. The no-frills design has an added benefit of minimizing cost and user training. This simple, portable, and compact detector is the best instrument for confined spaces or potentially dangerous worksites.

Highest standards of reliability

The typical batter life ranges between 8 and 13 hours depending on the temperature. The durable and long lasting batteries can fully recharge in approximately 6 hours. The GasAlertMax XT II and its sensors feature a standard two year warranty. With safety and reliability as a top priority, BW Technologies has developed the multigas detector to utilize the most advanced technology on the market, while maintaining its simplicity and portability. When working in settings with possible gas exposure, users can be certain that the gas levels are being accurately and reliably monitored with the best technology available.

Part Number: XTXWH0YAU

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

65-2618RK-CL2 M2, Chlorine (Cl2) 0-3 ppm Sensor/Transmitter, Non Explosion Proof with J-Box by RKI Instruments

RKI Instruments uses the latest cutting edge technology when developing transmitters and sensors. Its dedication to workplace safety and reliable safety solutions is unparalleled. The M2 Stand Alone Transmitter utilizes state of the art sensor cell technology to integrate workplace safety with the industry's more advanced transmitter technologies.

M2 Stand Alone Transmitter

The M2 Stand Alone Transmitter is operational with or without a controller and is available in two forms: explosion proof and non-explosion proof. The unit has a backlit screen for a direct digital readout, and a user friendly setup with push buttons and easy to read LCD menus. The advanced technology transmitter can function as an independent standalone system or as part of an integrated detection and transmission system. Using state of the art technology, the transmitter uses a magnetic want technique for performing non-intrusive calibration. For optimal stability and accurate readings, the unit provides an automatic zero drift correction feature. This also reduces the need for adjustments due to sensor aging.

The M2 Stand Alone Transmitter is available for LEL, H2S, CO, PPM, HC, CO2, CI2, NH3, SO2, HCN, and more. The unit also features an infrared sensor for CO2 and combustible gases. With 2 fully programmable alarms and a fail relay, the visual color coded LED alarms are reliable and customizable to meet specific needs.

Advanced sensor technology

The state of the art sensors are long lasting with a lifespan typically over two years. Sensor construction is rated Class I, Division 1 groups B, C, and D for flammables, CO, H2S, O2, and CO2. The sensors are rated Class I, Division 2 for all other toxic gases. Depending on the gas, the sensors will operate through a catalytic, galvanic cell, electrochemical, or infrared design. The plug in nature of the sensors allows for a quick and tool free onsite replacement.

Specifications

Each transmitter features 2 to 3 years of life with normal service. The explosion proof LEL H2 specific transmitter has 3 to 5 years with normal service, and the explosion proof carbon dioxide, methane, and hydrocarbons feature over 5 years of life with normal service. The explosion proof transmitters are also water repellant. Each device is approximately 8.5 H x 5.2 W x 4.5 D and features an alphanumeric display with a backlight. The screen displays 8 characters per line with 2 lines for gas concentration readouts.

Optional Accessories

The M2 Stand Alone Transmitter has a variety of optional accessories available including calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors or panels, and dataloggers. The transmitters are directly compatible with Beacon 110, 200, 410, and 800 controllers.

*Please note we can only ship RKI products to customers within the United States