All Products

2811-708-002 EC 28 Gas Transmitter with Carbon Monoxide (CO-H) Reduced H2 sensitivity, 0 - 500 ppm, Display by GfG

Advanced Technology

Wherever hazards are expected, the EC 28 transmitter and GfG's proven monitoring systems are the right choice for reliable surveillance. The ATEX-certified design, an integrated, Ex-proof buzzer, and bright alarm LEDs provide the highest safety in hazardous areas by including visual and audible alarms. The gas alarm not only alerts the person in the control room of hazards, but also the person on-site.

Easy handling

Smart sensor technology allows a user to install the transmitter or to replace a sensor within a few seconds - just plug the sensor into the transmitter. Adjustments are done directly at the transmitter using touch keys or with the remote control (one-person calibration).

Remote Control RC2

Ammonia and hydrogen are lighter than air. With the transmitter installed close to the ceiling, GfG can provide permanently connected cables with plugs for the remote control, which allow the user to do all adjustments without having to climb a ladder. In addition, one remote control can be used for several transmitters, which helps cut costs and increase efficiency.

The remote control display is always identical to that of the transmitter, making inspection, service, and calibration considerably simple.

The remote control reads the current gas concentration and can be used as an external display.

Integrated Alarm - Saves Money on Ex-proof Alarm and Wiring!

The EC 28 D model shows the current gas concentration on-site at the display of the transmitter and also at GfG's GMA controller.

The EC 28 DA provides additional bright alarm LEDs and a buzzer - avoiding costs for a separate Ex-proof horn and an Ex-proof light. You also save money on wiring to connect the controller and alarm devices.

In combination with GfG's flexible control units, the EC 28 provides various possibilities for reliable and cost-effective gas monitoring.

Reliable Measurement, Increased Safety, Minimized Cost of Operation

Accurate sensors and integrated temperature compensation provide the highest measurement accuracy. Low maintenance requirements and the long sensor life reduce your cost of ownership.

Features

• Reading of gas concentration at transmitter display
• Ex-proof visual and audible alarms
• ATEX certificate II 1 G EEx ia IIC T4 / II 2 G EEx em [ib] IIC T4
• One-person calibration at transmitter using touch keys or remote control
• Plug-in smart sensor - sensor replacement without opening the casing

Advantages

• Concentration display at transmitter or at remote control
• ATEX II 1 G EEx ia IIC T4 / II 2 G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need for expensive Ex-proof buzzer or wiring
• Easy sensor replacement by means of plug-in smart sensors
• Long sensor life
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments without opening the casing using touch keys or remote control; easy handling even for hardto-reach transmitter positions

XT-XWH0-Y-OE GasAlertMax XT II 3 Gas Detector, Combustible (% LEL), Oxygen (O2), Hydrogen Sulfide (H2S) - Yellow Housing, OE Version (Other Regions, 2-pin UK plug) by BW Technologies

GasAlertMax XT II is the safest and most economical choice for multi-gas detection systems. Utilizing the most advanced technology on the market, the GasAlertMax accurately and reliably monitors up to four hazardous conditions, and offers a simple user friendly device for easy operation. Its standard safety features and compatibility with other instruments ensure that the gas detector is the best instrument for gas monitoring compliance.

GasAlertMax XT II specifications

The lightweight and portable unit is approximately 11.5 ounces, and features the latest technology allowing for a compact design. With an operational temperature range of -4 to 122 degrees Fahrenheit, the monitor is designed to function effectively in many harsh conditions. The cautionary yellow outer shell helps to ensure that the gas detector is carried with the user not left onsite. Additionally, the durable casing is resistant to water and features a built-in concussion proof boot.

Triple alarm system

The GasAlertMax XT II features a triple alarm system designed to alert users of potentially hazardous conditions. When the gas sensors detect specified levels of H2S, CO, O2, or combustible gases, the instrument will begin the triple alarm alert and notify users and those nearby. The device indicates these dangers with a vibrating alarm, an ultra bright visual alarm, and an audible alarm of over 95 decibels. The alarms are also designed to alert users of administrative needs such as battery replacement.

GasAlertMax XT II features

The GasAlertMax XT II has multi-language support features in English, French, Spanish, German, and Portuguese. The gas detector also has state of the art block detection with semi-conductor pressure sensor, and standard data and event logging. Accessories such as the belt holster, multi-unit cradle charger, and concussion proof boot are also available.

Upon activation, the unit will automatically test sensors, pumps, battery, and circuitry. For additional test and calibration, the GasAlertMax XT II is compatible with the MicroDock II automated test and calibration system and Fleet Manager II. Improving on its functionality, the unit is customizable. Users can change options for forced calibration and tests, safety locks, alarm setpoints, safe display mode, language choices, start-up message, and more.

The easy to read LCD screen displays continuous information about real-time gas concentrations and alarms. To maintain simplicity and ease of use, the GasAlertMax XT II also features a user and glove friendly one touch button for operation. The no-frills design has an added benefit of minimizing cost and user training. This simple, portable, and compact detector is the best instrument for confined spaces or potentially dangerous worksites.

Highest standards of reliability

The typical batter life ranges between 8 and 13 hours depending on the temperature. The durable and long lasting batteries can fully recharge in approximately 6 hours. The GasAlertMax XT II and its sensors feature a standard two year warranty. With safety and reliability as a top priority, BW Technologies has developed the multigas detector to utilize the most advanced technology on the market, while maintaining its simplicity and portability. When working in settings with possible gas exposure, users can be certain that the gas levels are being accurately and reliably monitored with the best technology available.

Part Number: XTXWH0YOE

WD-35802-19 Fluoride F- Double-junction Ion-Selective Electrode (ISE) by Oakton

Double junction makes these electrodes ideal even for rugged applications

Use these economical Ion Selective Electrodes (ISEs) with the ION 510 meter, pH 2500 Ion benchtop meter, or the Ion Acorn meters. They also are suitable for use with any other ion meter, or with any meter with 0.1 mV resolution. All ISEs feature a BNC connector and 3-ft cable.

ISE solution kits contain the solutions and accessories needed for calibration, sample preparation and measurement of ion concentration and activity. All solutions are supplied with MSDS (Material Safety Data Sheet) and have a value of 1000 ppm.

• Each features a BNC connector and 3-ft cable

5201-2113 GDC-150 Gas Sensor Transmitter, NEMA 4 Housing, HCHO (Formaldehyde) Sensor w/Display by Bacharach

The all new GDC-150 transmitter from Bacharach offers detection and protection for a wide range of hazards including toxic gases such as carbon monoxide (CO), oxygen depletion, combustible gases, refrigerant leaks and total volatile organic compounds (TVOCs). Analog interfaces allow the transmitter to be connected back to Bacharach's GDA Series of controllers (or any other gas detection controller), building management systems or control systems. The GDC-150 features 4-20 mA or 0-10 VDC linear output signals, an automatic thermal resetting fuse, RoHS compliant circuit boards and LED indicators for power and open loop.

The onboard alarm LED's indicate when alarm threshold values are exceeded. The unit can be ordered with an optional alpha numeric LED display that shows gas concentrations in real time while alarm relays alert personnel of potential dangers, avoiding incidents and potential hazards.

The GDC-150 is packaged in a rugged, polycarbonate housing for both indoor and outdoor applications. When leaks occur, the GDC-150 sensors respond quickly and accurately to protect people and property. Automated calibration and simple maintenance procedures performed in the field allow for continuous operation and assurance that areas are monitored and protected at all times.

*Please note we can only ship RKI products to customers within the United States

6230M pH/mV/Temp. Microprocessor Handheld Meter by Jenco

pH/mV/Temp. microprocessor handheld meter in splash proof case with 3 point calibration, 40 memory storage, RS-232-C IBM compatible communication interface and BNC, pH/ORP connector with 8-pin DIN ATC connector. AC/DC power. CE Approved.

• 3 point calibration
• 40 memory storage
• Power down memories
• Electrode offset recognition
• Electrode slope recognition
• Built in buffer temp. coefficients
• ATC
• RS-232c output
• CE approved
• Splash resistant/watertight case
• Battery/ac adaptor
• High 50/60hz noise rejection
• UL approved ac line adaptor
• Aconventional 9v battery
• Highly reliable mechanical touch keys with audio feedback

*Please note we can only ship RKI products to customers within the United States

*Please note we can only ship RKI products to customers within the United States

Part Number: 34L-357

M031-1111-000 MicroRAE Wireless Gas Monitor, CSA/BLE/LEL/O2/CO by RAE Systems

The MicroRAE four-gas portable detector brings enhanced user-friendliness and flexibility to wireless gas detection. This enables continuous, instant visibility of safety threats for faster, more informed decisions, to protect workers, facilities, and the environment, and to optimize operations.

The MicroRAE is a wireless diffusion detector that simultaneously monitors up to four gases, including hydrogen sulfide, carbon monoxide, oxygen and combustibles (LEL). With its different wireless connectivity options the MicroRAE can deliver real-time instrument readings and alarm status to other wireless offerings such as ConneXt Plus, ConneXt Pro, ConneXt Loneworker4 and Safety Communicator.

• Man Down Alarm with real-time remote wireless notification1
• GPS module for location
• Bluetooth® low energy connection to a Smart Phone device for uplink data communication and device configuration
• Remote notification and Panic function
• Fully automated bump testing and calibration with AutoRAE 2

Industries

Personal protection and general safety and compliance in:

• Lone Worker Applications
• Oil and Gas
• Waste water treatment
• Utilities
• Telecommunications
• Firefighting
• Petrochemicals
• Construction

Optional Accessories

• AutoRAE 2 Automatic Test and Calibration Systems
• Gang Charger (5 units)
• Auxiliary filter
• Hand pump kit
• Truck mount charger

Features & Benefits

• Honeywell ConneXt compatible with Mesh and Wifi wireless configurations
• Compact and lightweight
• IP-67 water and dust-resistant case
• Strong, protective, concussion-proof design
• Real-time gas concentration readings, location, alarm and status enabled by state of-the-art wireless technology
• Unmistakable five-way local and remote notification of alarm conditions
• Short bump test and calibration time
• Global approval for worldwide acceptance
• Filtered LEL sensor options to inhibit sensor poisoning
• Compatible with Safety Communicator
• Device Management with Honeywell SafetySuite

WD-35630-12 pH/CON 450 Portable Waterproof pH/CON Meter with with Separate Probes by Oakton

The pH/CON 450 meter offers a rugged, waterproof housing, making it ideal for the manufacturing floor, field testing, and the laboratory. Large, backlit LCD lets you view the main measurement simultaneously with temperature. Calibrate pH with up to six points from USA, NIST, DIN, PWB, and custom pH buffer sets. Autocal feature for conductivity has one calibration point per range. ATC ensures measurement accuracy even in fluctuating temperatures.

Meter features include ready (stability) indicator, smart averaging, user-selectable C/F units, hold function, calibration alarm, battery life-indicator, and electrode status.

Perform data logging with manual or timed collection of up to 500 data sets with real-time clock time/date stamp. Order optional data cable for USB and RS-232 connectivity. Choose combination pH/CON probe or separate probe options.

• Intuitive, user-friendly icons-electrode status displays pH slope
• Grip-Clip electrode holder quickly and easily secures electrode to side of beaker or container
• USB or RS-232 output for up to 500 data sets
• Extended battery life or optional universal power adapter
• Built-in stand with wall mount allows for easy benchtop measurement or storage

6130-2051 MGD-100 Gas Detection System, Combustible Gas: 2 Sensors, 2 Alarms, IP66 Housing, 110 VAC by Bacharach

Bacharach's MGD-100 Series is a robust and scalable gas detection system used for reliable real-time monitoring of refrigerant, combustible, and toxic gases. It's a stand-alone system that alarms when pre-set thresholds are exceeded. The MGD-100's alarms are monitored by a centralized controller, which can alert personnel of potential hazardous conditions via an onboard buzzer and LED alarm indicators.

MGD-100 Systems can be configured from single-sensor, one-alarm level systems to larger scale systems consisting of 6 sensors with 2 alarm levels. This flexibility allows the platform to be used for both small and large systems.

Ideal for Chiller Rooms, Supermarkets, Brewing and Bottling Facilities, Industrial Refrigeration, Arenas, Food Storage and Processing Facilities.

Features & Benefits:

• Stand-alone, out-of-the-box solution with quick and easy installation - the most cost-effective system available.
• Fast-response sensors detect leaks quickly, which minimize refrigerant gas usage and environmental impact.
• Infrared (NDIR) CO2 detection
• Long-life semiconductor sensors for detection of all refrigerants, ammonia, halocarbons, combustibles & VOCs
• Robust design allows units to be placed directly in areas where detection is needed.
• Available in a variety of housings, including IP66 and duct mount.
• Select from 1, 2, 4 or 6 remote sensors and 1 or 2 pre-set alarm levels, which can be connected to BMS systems.

SCT-108.003.02 SCT BEN-pH-2 pH Meter with ATC & RS232 by ScichemTech

SCT basic benchtop pH/ORP/temp meter with ATC and with RS232 suitable for general pH measurement in laboratory

Includes:

• Plastic pH combination electrode
• Standard solution pH 4.00, 7.00, 10.01 (50 ml)
• 9V power adapter
• Electrode holder
• Operation manual

Features:

• SCT benchtop meter is designed to measure pH,ORP, temperature.
• Large LCD with blue background can display both pH and temperature value at the same time.
• It has intelligent functions for automatic calibration, automatic temperature compensation, data storage/recall, and memory max. and min. value etc.
• 1~3 point automatic calibration, and it can automatically display the percentage of slope after finishing calibration
• °C and °F can be switched freely.
• SCT benchtop meter meets ISO9001:2008 & CE standards

8326839 X-am 5100 Hydrazine (US) by Draeger

For manufacturing petrochemical products, aseptic packing, or handling of rocket fuel: the Draeger X-am 5100 portable single-gas detector ensures safe handling of HF, HCl, H₂O₂ or hydrazine – thanks to proven Draeger sensor technology and a device design which is perfectly customized to reactive gases.

YOUR ADVANTAGES AT A GLANCE

• Continuous, precise and reliable measurement
• A special device design with direct gas entry provides fast sensor response and precise measurement data by preventing gas adsorption on the device housing
• Lightweight and robust
• Slip-proof and compact design
• Triple alarm: visual (360°), audible (multi-tone), vibration
• Easy to use: two-button operation and user-friendly menus
• Highly resistant to impacts, vibrations and electromagnetic radiation
• Can be operated using replaceable alkaline batteries or a T4 NiMH rechargeable battery, which can be charged right in the device

T76 Waterproof TDS Tester with Replaceable Electrode (high range) by Milwaukee

These instruments are designed for all applications. It's IP65 Waterproof casing and replaceable electrode make them suitable also for heavy duty applications, such as Waste Water treatment and Agriculture. The modular design allows easy electrode and battery replacement.

All Waterproof testers are supplied in a leather casing complete with calibration solution, batteries, instruction manual and screwdriver for calibration.

The T76 is a waterproof TDS tester with automatic temperature compensation, 1 point manual calibration and a range of 0 to 9999 ppm (mg/L). The tester has a replaceable electrode and is supplied complete with sachets of calibration solution, leather casing and calibration screwdriver.