$1000 - $2000

2216017 CS 21 Fixed Gas Transmitter, HCFC-22 (CHClF2) (6 Cable), 50 to 5000 ppm by GfG

The CS 21 transmitter uses the proven chemosorption detection principle for detection of toxic gases, vapors and combustibles. The rapid response of the transmitter provides opportunity to take counter measures and thereby limit damages. The long life of the sensors makes the CS 21 a low-cost solution for your detection needs. A transmitter can be continuously operated for more than 5 years.

Wall mount installation is straightforward. The distance between transmitter and controller can be greater than 500 m. A rugged aluminum casing protects the sensor and electronics from splashes of water and dirt. The transmitter must not be operated in EX-areas. For measurement of combustible gases in the LEL range the gas needs to be sampled by pump. In this case the EX-protection needs to be guaranteed with suitable external components (e.g.flame-protection).

• High sensitivity to a broad range of refrigerants
• Long sensor life
• Fast response

2106B1418 Sensepoint Hazardous Area Approved Gas Detector, NO 0-100 ppm Toxic Sensor M20 by Honeywell Analytics

The Sensepoint range of flammable, toxic and Oxygen gas detectors offer users a high quality, low cost solution to their industrial gas monitoring needs. Installation in potentially explosive atmospheres is made by the use of a suitable Ex d or Ex e approved junction box. The industry standard outputs from Sensepoint are connected to either a choice of Honeywell Analytics' controllers or 3rd party DCS/ PLC systems. Both flammable and toxic versions are certified to the latest ATEX/IECEx safety and performance standards.

The flammable detector is available in either % LEL or PPM detection range versions and provides an industry standard mV bridge output. Typical life expectancy is greater than 5 years, after which the detector is simply replaced with a new one.

The toxic detectors are supplied pre calibrated for easy installation and provide an industry standard 2 wire 4-20mA loop output. User connections are Ex d, while front end Intrinsic Safety (IS) design allows for easy exchange of the replaceable sensor while powered. IS design also removes the need for a sinter enabling very fast speed of response and detection of 'sticky' gases such as Chlorine and Ammonia.

Sensepoint has proven its suitability across a wide range of demanding applications by delivering high performance and reliability at an affordable cost.

Fit For Purpose

• Flammable, toxic and Oxygen versions available
• High performance, low cost
• Suitable for new and retro fit applications

Proven Sensor Technology

• Surecell™ electrochemical sensors
• Poison resistant catalytic bead
• Fast and reliable
• Typical 2 to 5 years operational life

ATEX/IECEx Certified

• Complies with the latest standards
• Hazardous area approval and performance
• IP65/67 for use in harsh environments

Easy to Use

• Factory set operation
• Simple to replace
• Minimal training required

Range of Accessories

• Weatherproof cap
• Flow adaptor
• Duct mounting kit
• Collecting cone

VP5-Q0002111801 Ventis Pro5 Personal Gas Monitor, CO2 (IR), Li-ion Extended Run Time Battery, Desktop Charger, Pump, Orange, KOSHA, English by Industrial Scientific

Detect up to five gases simultaneously with the rugged, wireless, Ventis® Pro5 Multi-Gas Monitor. With Ventis Pro5, safety goes beyond the gas detector whether you need team-based alarm sharing, remote monitoring with location details, or both. The monitor is also backed by a Guaranteed for Life™ warranty.

• Eliminate the need for two pieces of equipment by using Ventis Pro5 for personal monitoring and confined space entry.
• Train workers on one, multi-purpose gas monitor and reduce the risk and investment of having different devices in the field.
• Improve team and site safety by locally sharing alarms and gas readings between wirelessly connected Ventis Pro5 monitors.
• Get real-time location and alarm data directly from Ventis Pro5 gas monitors to a designated safety contact with the optional cellular or wi-fi battery pack.
• Reinforce safe behavior with programmable alarm action messages like "EVACUATE" or "VENTILATE" based on alarm level.
• Simplify the user experience with the ability to hide unnecessary screens based on user needs, role, industry, or site.

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

XT-XWHM-Y-CN GasAlertMax XT II 4 Gas Detector, Combustible (% LEL), Oxygen (O2), Hydrogen Sulfide (H2S), Carbon Monoxide (CO) - Yellow Housing, CN Version (China/New Zealand) by BW Technologies

GasAlertMax XT II is the safest and most economical choice for multi-gas detection systems. Utilizing the most advanced technology on the market, the GasAlertMax accurately and reliably monitors up to four hazardous conditions, and offers a simple user friendly device for easy operation. Its standard safety features and compatibility with other instruments ensure that the gas detector is the best instrument for gas monitoring compliance.

GasAlertMax XT II specifications

The lightweight and portable unit is approximately 11.5 ounces, and features the latest technology allowing for a compact design. With an operational temperature range of -4 to 122 degrees Fahrenheit, the monitor is designed to function effectively in many harsh conditions. The cautionary yellow outer shell helps to ensure that the gas detector is carried with the user not left onsite. Additionally, the durable casing is resistant to water and features a built-in concussion proof boot.

Triple alarm system

The GasAlertMax XT II features a triple alarm system designed to alert users of potentially hazardous conditions. When the gas sensors detect specified levels of H2S, CO, O2, or combustible gases, the instrument will begin the triple alarm alert and notify users and those nearby. The device indicates these dangers with a vibrating alarm, an ultra bright visual alarm, and an audible alarm of over 95 decibels. The alarms are also designed to alert users of administrative needs such as battery replacement.

GasAlertMax XT II features

The GasAlertMax XT II has multi-language support features in English, French, Spanish, German, and Portuguese. The gas detector also has state of the art block detection with semi-conductor pressure sensor, and standard data and event logging. Accessories such as the belt holster, multi-unit cradle charger, and concussion proof boot are also available.

Upon activation, the unit will automatically test sensors, pumps, battery, and circuitry. For additional test and calibration, the GasAlertMax XT II is compatible with the MicroDock II automated test and calibration system and Fleet Manager II. Improving on its functionality, the unit is customizable. Users can change options for forced calibration and tests, safety locks, alarm setpoints, safe display mode, language choices, start-up message, and more.

The easy to read LCD screen displays continuous information about real-time gas concentrations and alarms. To maintain simplicity and ease of use, the GasAlertMax XT II also features a user and glove friendly one touch button for operation. The no-frills design has an added benefit of minimizing cost and user training. This simple, portable, and compact detector is the best instrument for confined spaces or potentially dangerous worksites.

Highest standards of reliability

The typical batter life ranges between 8 and 13 hours depending on the temperature. The durable and long lasting batteries can fully recharge in approximately 6 hours. The GasAlertMax XT II and its sensors feature a standard two year warranty. With safety and reliability as a top priority, BW Technologies has developed the multigas detector to utilize the most advanced technology on the market, while maintaining its simplicity and portability. When working in settings with possible gas exposure, users can be certain that the gas levels are being accurately and reliably monitored with the best technology available.

Part Number: XTXWHMYCN

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

65-2341-NH3-5 S2 Series Sensor/Transmitter, Ammonia (NH3) 0 - 500 ppm, CT-7 style, non explosion proof with j-box by RKI Instruments

Having a reliable gas sensor is detrimental to the safety and security of workers in potentially unstable work environments. In many cases, the decision to use a gas detection device with a reliable sensor can be the difference between life and death. RKI Instruments understands the reliability of gas sensors should be a top priority for workplace safety managers. Their team of experts works diligently to incorporate the most advanced technologies with the highest industry standards.

For nearly 20 years, RKI Instruments has worked in the gas detection industry. Its line of products leads the industry in innovation and technology. Every year, the company commits to achieving a higher level of productivity and delivering the best gas detection products on the market. With the introduction of their high performing, low cost S2 Sensor Transmitter, RKI is fulfilling that commitment.

S2 Sensor/Transmitter

The RKI S2 Sensors and Transmitters use state of the art sensor technology to detect common gas hazards. Their efficient design and cost effectiveness make them an industry choice for atmospheric monitoring. The sensor transmitters can be used in both indoor and outdoor conditions and are designed to interface with RKI controllers or PLC/DCS systems.

The sensors are available in explosion proof casing for monitoring LEL, H2 specific, oxygen, H2S, CO2, and carbon monoxide. These sensors also have flame arrestors and are approved for use in hazardous environments. The oxygen, H2S, CO, and CO2 sensors are available in non-explosion proof models. The sensors provide highly specific and quick detection and are long lasting. The sensors can be quickly replaced while on the field and do not require any tools.

Explosion proof S2 Sensor/Transmitter

The explosion proof sensors use a variety of detection mechanisms including catalytic for LEL and LEL- H2 specific; metal oxide semiconductor for hydrogen; galvanic cell technology for oxygen; electrochemical for hydrogen sulfide and carbon monoxide; and infrared for carbon dioxide, methane, and hydrocarbons. A hydrogen specific sensor transmitter is not available. Each of these detection methods come with their own measuring range specifications and response times varying from 20 seconds to 45 seconds. These sensors are stainless steel and are housed in a cast aluminum explosion proof J-Box (a stainless steel J-Box is also available).

Non-explosion proof S2 Sensor/Transmitter

The non-explosion proof sensors use galvanic cells for oxygen detection; electrochemical technology for hydrogen sulfide, carbon monoxide, and other toxics; and infrared technology for carbon dioxide detection. The response times vary between 20 seconds and 60 seconds depending on the targeted gas, and the measuring ranges vary as well. These sensors are plastic or aluminum and housed in an explosion proof J-Box.

Accessories

The S2 Sensor/Transmitter has numerous accessories available to meet the individual workplace's needs. Such accessories include calibration adaptors, flow through adaptors, remote horns and lights, calibration kits, battery backups, splash guards, air aspirator adaptors or panels, and data loggers.

Each sensor comes standard with a one year warranty for materials and workmanship.

*Please note we can only ship RKI products to customers within the United States

S3KAL2 ATEX/IECEx Approved Series 3000 MkII Toxic and Oxygen Transmitter, Aluminium LM25 and 2 x M20 Entries by Honeywell Analytics

Honeywell International is a company with a diverse array of technology and manufacturing products. With over 200 collective years of experience, Honeywell utilizes its specially trained team of scientists and engineers to design products and solutions for workplace safety and gas detection. Every Honeywell product utilizes advanced technology and Honeywell works vigorously to provide updates and upgrades to ensure that customers always have access to the most cutting edge technologies. The Series 3000 MKII represents this commitment to advanced technologies and workplace innovation.

Series 3000 MKII

The rugged and reliable Series 3000 MKII is applicable to a wide variety of worksite including oil and gas worksites, refineries, power plants, and other environments with potentially explosive atmospheres. Its proven electrochemical sensor technology ensures fast and reliable readings. The Series 3000 MKII is a replacement for the popular Series 3000 XPIS and provides some added features including 2 cable gland/conduit entries and more useable aluminum or stainless steel enclosures. The new unit is designed to detect toxic gases or oxygen hazards in potentially hazardous environments.

Reduce Costs for Installation and Maintenance

The Series 3000 MKII is able to save companies money by reducing installation and maintenance costs. With the universal mounting bracket included in a standard purchase, worksites can install the unit without assistant. Additionally, field wiring can run along with other instruments because the transmitter is explosion proof. Finally, the plug in style of the smart sensor eliminates the cost of wiring installation. As an added bonus, users can program the calibration frequency and utilize the fault diagnostic software to identify problems without needing to pay for a maintenance professional.

For convenience, the sensor interface is intrinsically safe. This allows it to be "hot swapped" without having to remove power to the gas detector. Additionally, the replacements for the stainless steel smart sensors are pre-calibrated allowing for an easy exchange. Each sensor is rated for over 2 years of life.

Specifications

The unit weighs approximately 3.75 pounds in the aluminum version and 8.16 pounds in the stainless steel version. Typical dimensions are 4.7" x 7.9" x 3.9". The unit is encased in a durable dust resistant and water resistant housing. The unit uses very little power and operates on an industry standard 2-wire, 4-20mAloop. For easy installation, the Series 3000 MKII comes standard with all necessary accessories and can be mounted on a wall or support pole using the provided universal bracket. The unit can also be installed electrically by using a conduit or cable with an appropriate mechanical protection.

The Series 3000 MKII is available with a variety of optional accessories for worksite customization. Optional accessories include a remote sensor mounting kit (which allows the sensor to be mounted up to 50 feet from the transmitter), a duct mounting kit, a pipe mounting bracket, a sunshade, a calibration cup to apply test gases, and a collecting cone.

G460-11-03-00-00-14 G460 Multi-Gas Detector with Alkaline Smart Pump and Alkaline Battery, O2, Catalytic Combustion LEL Sensor, CO and H2S Sensor by GfG

For over 50 years, GfG Instrumentation has worked to develop the most reliable and effective equipment for gas detection and measurement technology. Developed by a team of highly experienced scientists and specially trained engineers, GfG products are high quality reliable instruments designed to meet the unique needs of potentially hazardous worksite. With the introduction of the G460 Multi-Gas Detector, GfG Instrumentation is continuing the trend.

G460 Multi-Gas Detector

The G460 Multi-Gas Detector is a compact and robust system with the capabilities of detecting up to six different gases and simultaneously displaying the readings. The portable detector features a user friendly and intuitive interface to simplify the day to day operations.

Ease of Use

For typical daily operations, the G460 Multi-Gas Detector operates with a single button. The complete user interface can provide access to advanced setup options with three buttons. The unit also features easy calibration operation. Simply attach the calibration adapter and apply gas. The G460 will automatically perform the appropriate adjustments. The detector will then store the dates of the three most recent calibrations for each sensor.

The G460 also features a large easy to read tricolor display which uses a color code to indicate the alarm severity. From green to orange to red, the tricolor display is intuitive and incredibly user friendly. The display feature can also flip or zoom with the touch of a button. The G460 multi-faceted alarm system also includes an ultra loud audible buzzer at 103 dB, a standard vibration mechanism, and 360 bright LED alerts (the LED alerts can also be equipped to function as flashlights). This multi-faceted system is sure to alert users and those nearby of the potential hazardous conditions. For smooth and continuous operations, the G460 Multi-Gas Detector uses interchangeable alkaline and rechargeable battery packs that provide up to 25 hours of continuous operation. Using a drop in cradle charger, the rechargeable pack can completely recharge in less than 4 hours.

G460 Multi-Gas Detector Features

The G460 Multi-Gas Detector features a motorized pump with a built-in diffusion or sample draw mode switch. The hose is easily attachable and can draw from 100 feet away. The hose is powered by its own battery pack that provides 20 hours of continuous operation. The multi-gas detector also features the widest range of sensors on the market. The compatible long lasting (and interchangeable) smart sensors include LEL, SO2, O2, H2, H2S, NO, CO, O3, HF, NH3, CIO2, CI2, PH3, ETO, HCN, and NO2. Users can purchase additional sensors to help customize the unit such as infrared sensors for the measurement of CO2 and photoionization sensors for volatile organic chemical hazards. The G460 has standard data logging capabilities that store up to 55 hours of the most recent activities. Alarm activations gas thresholds and stored permanently in the internal memory. Employers can download all internal information to generate reports and monitor results.

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

2801-38-001 CC 28 Fixed Gas Transmitter with Gas Optimized Catalytic Sensor 0-100% LEL (MK 208-1), Propylene (C3H6), No Display by GfG

Superior technology

In areas where combustible gas or vapor hazards may exist, GfG s new CC 28 combustible transmitter is the perfect choice for reliable area monitoring. With its proven design, this ATEX certified transmitter offers an integrated explosion-proof buzzer and bright-alarm LEDs for reliable warning of combustible gas hazards (even in hazardous locations). This superior design provides warnings for immediate personnel, and ensures entire plant safety.

Easy handling

Smart sensor technology allows easy installation. Sensor replacement takes only a few seconds-simply plug in the sensor. User adjustments are performed at the transmitter with simple touch keys, or with the optional remote control interface (one person calibration).

RC2 remote control

Several combustible gases are lighter than air. With the transmitter mounted close to the ceiling, calibration can be difficult. The remote control for the CC 28 allows you to perform calibration or zero adjustments without the need of a ladder or lift. A flexible cable connects the remote control to the transmitter and displays the same reading as the display on the transmitter. With the remote control inspection,service and calibration can be performed easily by one person.

The sensor and the integrated temperature compensation provide highest measurement accuracy.

Low maintenance requirements and long sensor life reduce your cost of ownership. Just sign a service contract and don t worry about any problems. We will service your system at regular intervals.

Models

Model CC 28D allows you to read the gas concentration both at the transmitter and at the GMA controller.With the RC2 remote control - the CC 28 is easy to use and to operate even if it is mounted at the ceiling.

Model CC 28DA provides additional warning with bright integrated alarm LEDs and a buzzer.

Features

• Full-featured smart transmitter for combustible gas measurement
• Non-intrusive calibration adjustment
• Expected sensor life of 5 years
• Increased safety design to reduce installation cost in potentially hazardous locations
• ATEX EEx dem [1b] IIC T4
• Proprietary, high performance combustible gas sensor
• Available in three configurations: Blind (no display), Display, Display with local alarms

Advantages at a glance

• Display of gas concentration at transmitter or remote control
• ATEX II G EEx dem [ib] IIC T4
• Ex-proof visual and audible alarms
• No need of expensive EX-proof buzzer or wiring
• Easy sensor replacement with plug-in sensors
• Long life sensor
• Low service requirement
• Permanent status and function display at transmitter
• Adjustments by means of touch keys or remote control without opening the casing
• Easy handling even at hard-to-reach accessible transmitter positions.

XT-XU00-B-EU GasAlertMax XT II 2 Gas Detector, Combustible (% LEL, unfiltered), Oxygen (O2) - Black Housing, EU version (Europe) by BW Technologies

GasAlertMax XT II is the safest and most economical choice for multi-gas detection systems. Utilizing the most advanced technology on the market, the GasAlertMax accurately and reliably monitors up to four hazardous conditions, and offers a simple user friendly device for easy operation. Its standard safety features and compatibility with other instruments ensure that the gas detector is the best instrument for gas monitoring compliance.

GasAlertMax XT II specifications

The lightweight and portable unit is approximately 11.5 ounces, and features the latest technology allowing for a compact design. With an operational temperature range of -4 to 122 degrees Fahrenheit, the monitor is designed to function effectively in many harsh conditions. The cautionary yellow outer shell helps to ensure that the gas detector is carried with the user not left onsite. Additionally, the durable casing is resistant to water and features a built-in concussion proof boot.

Triple alarm system

The GasAlertMax XT II features a triple alarm system designed to alert users of potentially hazardous conditions. When the gas sensors detect specified levels of H2S, CO, O2, or combustible gases, the instrument will begin the triple alarm alert and notify users and those nearby. The device indicates these dangers with a vibrating alarm, an ultra bright visual alarm, and an audible alarm of over 95 decibels. The alarms are also designed to alert users of administrative needs such as battery replacement.

GasAlertMax XT II features

The GasAlertMax XT II has multi-language support features in English, French, Spanish, German, and Portuguese. The gas detector also has state of the art block detection with semi-conductor pressure sensor, and standard data and event logging. Accessories such as the belt holster, multi-unit cradle charger, and concussion proof boot are also available.

Upon activation, the unit will automatically test sensors, pumps, battery, and circuitry. For additional test and calibration, the GasAlertMax XT II is compatible with the MicroDock II automated test and calibration system and Fleet Manager II. Improving on its functionality, the unit is customizable. Users can change options for forced calibration and tests, safety locks, alarm setpoints, safe display mode, language choices, start-up message, and more.

The easy to read LCD screen displays continuous information about real-time gas concentrations and alarms. To maintain simplicity and ease of use, the GasAlertMax XT II also features a user and glove friendly one touch button for operation. The no-frills design has an added benefit of minimizing cost and user training. This simple, portable, and compact detector is the best instrument for confined spaces or potentially dangerous worksites.

Highest standards of reliability

The typical batter life ranges between 8 and 13 hours depending on the temperature. The durable and long lasting batteries can fully recharge in approximately 6 hours. The GasAlertMax XT II and its sensors feature a standard two year warranty. With safety and reliability as a top priority, BW Technologies has developed the multigas detector to utilize the most advanced technology on the market, while maintaining its simplicity and portability. When working in settings with possible gas exposure, users can be certain that the gas levels are being accurately and reliably monitored with the best technology available.

Part Number: XT-XU00-B-EU

0563 8451 845 Adjustable Focus IR Thermometer with Aluminium Case and Humidity Module by Testo

For the first time, surface temperatures with smallest diameters can be measured accurately at short and long distances. The switchable optics for far-field and close focus measurement make this possible. Far-field measurements are carried out at an optical resolution of 75:1. In this way, surface temperatures can be measured accurately even at great distances from the object to be measured. At a distance of 1.2 metres from the object to be measured, the measuring spot diameter is only 16 mm. A cross laser marks the measuring spot exactly during measurement. During measurements at a short distance from the object being measured, the close focus optics has a spot diameter of only 1 mm at a distance of 70 mm. Two laser points mark the spot exactly.

• Switchable optics for far-field measurements (75:1) and close focus (1 mm, distance 70 mm)
• Especially bright cross laser sighting for indicating the actual measurement point
• Integrated humidity module for measuring indoor air humidity and for determining dewpoint distance
• Reference accuracy ± 0.75 °C with super-fast measurement technology (scanning 100 ms)
• Backlit display (3-line), shows °C, %RH, °C td, min./max. values, alarm limit values and degree of emission
• Optical and audible alarm when limit values are exceeded
• Probe socket for TC probe for determining emissivity
• Instrument memory for 90 measurement protocols
• PC software for archiving and documenting measurement data (included in delivery)
• Tripod fitting for online measurement via USB cable (included in delivery)
• Measurement data documentation on site with Testo printer

GD-K8A-HBR GD-K8A Diffusion Sensor/Transmitter, HBR, 0 - 6 ppm by RKI Instruments

The GD-K8A is a diffusion style toxic gas detection transmitter ideally suited to meet your toxic gas detection needs. You can choose from a wide variety of toxic sensors to install in this model. The GD-K8A is an ideal solution for many toxic gas monitoring applications. The low profile design is only 1.5 inches thick and is easy to install. The hinged housing makes it easy to maintain. This transmitter can be installed with any RKI controller, or integrated to existing PLC or DCS system via 4-20mA output (24VDC two-wire, loop powered).

The sensors for the GD-K8A are aged and tested over a one to three month period, typically resulting in a three to five year life span, providing a lower cost of ownership for your gas detection system. The sensors are robust electrochemical type that feature higher sensitivity and selectivity. Fast sensor response time and excellent stability make these sensors the most reliable and longest-life electrochemical sensors available today.

At the heart of any gas detector is the sensor. With over 65 years of sensor technology experience, RKI has the knowledge and capability to provide the most advanced detection techniques and manufacture the most stable and long lasting sensors in the world. As a result the GD-K8A is one of the most stable and long lasting toxic transmitters on the market.

Features

• Diffusion style head
• Low profile design
• Quick response sensors
• Many toxic sensors to choose from
• 3 to 5 year typical sensor life
• Easy maintenance
• Selective for target gas
• Low cost of ownership

Applications

• Semiconductor manufacturing
• Petrochemical plants
• Refineries
• Water & wastewater treatment plants
• Pulp & paper mills
• Gas, telephone, & electric utilities
• Steel
• Automotive
• Refrigeration
• Food Storage
• Power Plants
• General Leak Detection

*Please note we can only ship RKI products to customers within the United States

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

XT-XU0M-B-NA GasAlertMax XT II 3 Gas Detector, Combustible (% LEL, unfiltered), Oxygen (O2), Carbon Monoxide (CO) - Black Housing, NA version (North America) by BW Technologies

GasAlertMax XT II is the safest and most economical choice for multi-gas detection systems. Utilizing the most advanced technology on the market, the GasAlertMax accurately and reliably monitors up to four hazardous conditions, and offers a simple user friendly device for easy operation. Its standard safety features and compatibility with other instruments ensure that the gas detector is the best instrument for gas monitoring compliance.

GasAlertMax XT II specifications

The lightweight and portable unit is approximately 11.5 ounces, and features the latest technology allowing for a compact design. With an operational temperature range of -4 to 122 degrees Fahrenheit, the monitor is designed to function effectively in many harsh conditions. The cautionary yellow outer shell helps to ensure that the gas detector is carried with the user not left onsite. Additionally, the durable casing is resistant to water and features a built-in concussion proof boot.

Triple alarm system

The GasAlertMax XT II features a triple alarm system designed to alert users of potentially hazardous conditions. When the gas sensors detect specified levels of H2S, CO, O2, or combustible gases, the instrument will begin the triple alarm alert and notify users and those nearby. The device indicates these dangers with a vibrating alarm, an ultra bright visual alarm, and an audible alarm of over 95 decibels. The alarms are also designed to alert users of administrative needs such as battery replacement.

GasAlertMax XT II features

The GasAlertMax XT II has multi-language support features in English, French, Spanish, German, and Portuguese. The gas detector also has state of the art block detection with semi-conductor pressure sensor, and standard data and event logging. Accessories such as the belt holster, multi-unit cradle charger, and concussion proof boot are also available.

Upon activation, the unit will automatically test sensors, pumps, battery, and circuitry. For additional test and calibration, the GasAlertMax XT II is compatible with the MicroDock II automated test and calibration system and Fleet Manager II. Improving on its functionality, the unit is customizable. Users can change options for forced calibration and tests, safety locks, alarm setpoints, safe display mode, language choices, start-up message, and more.

The easy to read LCD screen displays continuous information about real-time gas concentrations and alarms. To maintain simplicity and ease of use, the GasAlertMax XT II also features a user and glove friendly one touch button for operation. The no-frills design has an added benefit of minimizing cost and user training. This simple, portable, and compact detector is the best instrument for confined spaces or potentially dangerous worksites.

Highest standards of reliability

The typical batter life ranges between 8 and 13 hours depending on the temperature. The durable and long lasting batteries can fully recharge in approximately 6 hours. The GasAlertMax XT II and its sensors feature a standard two year warranty. With safety and reliability as a top priority, BW Technologies has developed the multigas detector to utilize the most advanced technology on the market, while maintaining its simplicity and portability. When working in settings with possible gas exposure, users can be certain that the gas levels are being accurately and reliably monitored with the best technology available.

Part Number: XT-XU0M-B-NA

Sperian Biosystems PhD6 Multigas Detector

The Biosystems PhD6 Multigas Detector is the latest development in compact multigas detection systems. The detector is proven to be compact, efficient, and cost effective. With dual alarm systems featuring ultra-loud audible indicators and ultra-bright LED visual indicators, users and those nearby are always notified when potential hazards may be present. When developing this detector, the engineers at SperianProtection Instrumentation also developed an express docking station that would reduce calibration time and labor costs. The detection and docking station help users meet record keeping requirements and reduce the risks of human error. With the SperianBiosystems PhD6 Multigas Detector, users can rest assured that they are receiving the very best in gas detection technology.

Key Features

The Biosystems PhD6 Multigas Detector is compatible with over 19 sensor choices including:

• PID
• IR-CO2
• IR-CH4
• Conventional LEL
• Oxygen
• 15 different toxic gas sensors

The gas detector is encased in a durable solid polycarbonate case with a rubber over mold for easy handling. It has an interchangeable battery pack with both Alkaline and Li-Ion rechargeable batteries. Both battery types offer up to 24 hour run times. The unit features dual audible alarms at 92 decibels and front and side ultra-bright LED visual alarms to ensure that the user and those nearby are always notified of possible hazardous conditions. For easy interpretation, the detector has an easy to read status bar and large LCD display that notifies users of the device s functionality and calibration due date. Using the menu options, users can easily adjust a variety of the instrument s settings.

Automatic Docking Station

When developing the PhD6 Multigas Detector, product developers also created an automatic docking station (Biosystems IQ6 Express Dock) to be fully compatible with the detector. The docking station aims to reduce labor time and costs by fully automating certain aspects of instrument maintenance including calibration, functionality testing, and record keeping. Using the Express Dock, users can maintain compliance with recordkeeping requirements by simply docking the detector in the station. The station will automatically perform a variety of operations without user intervention.

Sperian Protection Instrumentation and Honeywell

Sperian Protection Instrumentation is a global leader in personal safety equipment. The company was recently acquired by Honeywell, another global leader in technology and innovation. As a Fortune 100 company, Honeywell has a vested interest in maintaining its reputation as a developer of efficient and reliable safety equipment. Sperian Protection Instrumentation helps to expand Honeywell s personal safety offerings while advancing their position in the American market. By purchasing a product by Sperian and Honeywell, customers can be assured they are receiving the very best in safety technology and equipment.

WD-35408-70 CON 600 Portable Waterproof Conductivity Meter with Kit by Oakton

Conductivity, TDS, resistivity, salinity measure from pure water to seawater!

• Durable waterproof and dustproof design with IP67 rating Even with no probes attached
• Single or multipoint calibration; auto or manual Fast, trouble-free calibration for more accurate measurements
• Large backlit graphic display Multi-line display with electrode status indicator, calibration data, and more
• User-settable calibration due alarm Out-of-date or unperformed calibrations are now things of the past!
• Built-in real-time clock Time-and-date stamping meets Good Laboratory Practice (GLP) standards
• Advanced data management Store up to 500 data sets and download via Infrared IrDA wireless interface
• Set point alarms Audible warning when readings are outside set points limit
• Accept 2-cell and 4-cell conductivity probes Measure over a broad conductivity range up to 500 mS/cm
• Password protection Security for calibration and setup menus
• Rugged rubber boot Protects meter from bumps and dings (optional; included with kits)

GD-K8AI-O3 GD-K8A Diffusion Sensor/Transmitter, Ozone (O3) 0 - 1.0 PPM, I.S. Type by RKI Instruments

The GD-K8A is a diffusion style toxic gas detection transmitter ideally suited to meet your toxic gas detection needs. You can choose from a wide variety of toxic sensors to install in this model. The GD-K8A is an ideal solution for many toxic gas monitoring applications. The low profile design is only 1.5 inches thick and is easy to install. The hinged housing makes it easy to maintain. This transmitter can be installed with any RKI controller, or integrated to existing PLC or DCS system via 4-20mA output (24VDC two-wire, loop powered).

The sensors for the GD-K8A are aged and tested over a one to three month period, typically resulting in a three to five year life span, providing a lower cost of ownership for your gas detection system. The sensors are robust electrochemical type that feature higher sensitivity and selectivity. Fast sensor response time and excellent stability make these sensors the most reliable and longest-life electrochemical sensors available today.

At the heart of any gas detector is the sensor. With over 65 years of sensor technology experience, RKI has the knowledge and capability to provide the most advanced detection techniques and manufacture the most stable and long lasting sensors in the world. As a result the GD-K8A is one of the most stable and long lasting toxic transmitters on the market.

Features

• Diffusion style head
• Low profile design
• Quick response sensors
• Many toxic sensors to choose from
• 3 to 5 year typical sensor life
• Easy maintenance
• Selective for target gas
• Low cost of ownership

Applications

• Semiconductor manufacturing
• Petrochemical plants
• Refineries
• Water & wastewater treatment plants
• Pulp & paper mills
• Gas, telephone, & electric utilities
• Steel
• Automotive
• Refrigeration
• Food Storage
• Power Plants
• General Leak Detection

*Please note we can only ship RKI products to customers within the United States

IR22-809 IR 22 Fixed Transmitter with Carbon Dioxide (CO2) MK 260-0, 0 - 10% vol., No Display / 4-20 mA by GfG

The IR 22 transmitter combines the proven infrared measurement method to detect carbon dioxide or combustible gases (HC) with the innovative technique of the new 22 series transmitters. This new GfG transmit- ter generation has been developed and manufactured according to SIL standards.

The comprehensive user menu and the versatile setting options make this transmitter series quite flexible and adaptable to all individual requirements. Precise measurement results at various environmental conditions, as well as the large dynamic measurement range of a few ppm up to 5 % volume CO₂ or 100% LEL.

Time-proven and innovative

The EC 22 is equipped with high quality GfG sensors. The transmitters are fitted with high-performance electronics for voltage stabilization, processing of readings, and temperature compensation. Follow up costs are minimized thanks to the long lifespan of the sensors.

Signal processing

The transmitter includes the complete electronic system for the signal processing and fail-safe forwarding of the measurement signal to the controller. The embedded software of the IR 22 linearises the measurement signal and compensates for environmental influences.

Therefore, when temperature variations are caused by the weather or changes of the humidity, the measured values will be accurate.

In addition, the transmitter provides the option to transfer service, maintenance and error messages to a connected GfG gas measurement controller. The IR 22 transmitter sends the signals either through an analog 4-20 mA current interface or a digital (RS485) Modbus interface.

Flexibility for any application

The IR 22 transmitter includes the sensor, status LEDs, either an analog or a digital interface, "Zero button" to adjust the zero point, and a test socket and potentiometer for the sensor calibration.

In addition, the IR 22 can be ordered with backlit graphical display. The display shows the current gas concentration, allows access to service functions, enables operation using a membrane keypad and includes optical and acoustical signal transmitters.

Features

• Long service life of the infrared (NDIR) sensor
• Extremely stable, low maintenance
• Cost effective single-man adjustment
• Output 4-20 mA or RS485 Modbus

VTS-L1232301101 Ventis MX4 Multi-Gas Monitor, LEL (Methane), CO, H2S, O2, Li-ion Extended Run Time Battery, Desktop Charger, No Pump, Orange, UL/CSA, English by Industrial Scientific

The Ventis® MX4 is a four-gas monitor with the portability and size of a single-gas monitor. Eliminate the need for extra monitors and transition seamlessly from personal monitoring to confined space entry with the Ventis® Slide-on Pump— ideal for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries.

• Detect up to four gases with a wide range of sensor options
• Select alarm set points, set latch alarms, disable instrument shutdown while in alarm, and more
• Save time and reduce human error with maintenance and usage data available from iNet Control software
• Available with or without an integral pump, or with the Ventis Slide-on Pump for ultimate flexibility
• Non-pumped instruments compatible with 12-hour, 18-hour, or 20-hour batteries

The Ventis® Slide-on Pump

The Ventis® Slide-on Pump is ideally suited for operators who wear their gas monitors primarily for personal protection but occasionally require a pump for confined space entries. Available in black or safety orange and powered by its own battery, the slide-on pump is compatible with the Ventis MX4 and Ventis® Pro5 Multi-Gas Monitor.

• Convenient Sampling – Sample draw distance of up to 50 feet provides convenient sampling in a wide range of applications
• Easy to Attach – No tools are required to attach or remove the Ventis Slide-on Pump to or from the monitor
• Uses Same Batterys and Chargers as Ventis – Monitor and pump each use the same batterys, and can easily be exchanged between instruments
• Flexible Battery Options – Three available battery options make this pump extremely flexible in the field