Data Loggers, Testo

0572 9001 Penetration Probe TC with Ribbon Cable, Type K, Cable Length 2 m, IP 54 by Testo

This thermocouple (TC) temperature probe with penetration tip can be used for measurements in pastes and semi-solid media and also for measurements in liquids and air.

The temperature probe features a thin, 2 m long ribbon cable. The thin ribbon cable can also be placed through narrow openings such as slits in doors or refrigerator seals.

Protection class IP 54 means that the temperature probe with penetration tip is protected against spray water.

This Type K, Class 1 thermocouple probe has a standardized accuracy of ±2.7 °F (±1.5 °C).

The temperature probe's response time t99 (time it takes for the probe to register 99% of the jump in temperature) of 7 seconds refers to measurements in moving water at 140 °F (+60 °C). This response time is extended when, for example, measurements are taken in still liquid, pastes or air.*

The perfect probe for any application

Don't see the temperature probe you are looking for? Please contact us directly. We have a large range of standard temperature probes and we also manufacture customized probes specifically according to your personal requirements.

* For air temperature measurements, the response time is about 40 - 60 times higher than the indicated value measured in water. If you should require a rather sluggish temperature probe to measure air temperature, this probe is particularly suitable because it does not take brief temperature peaks into account at all, or only to a very small degree, when measuring temperature. For example, if you are planning to use the temperature probe with penetration tip to measure air temperature in the refrigerator, briefly opening the refrigerator door would not take into account the temperature fluctuation which results from mixing the warm room temperature with the refrigerator temperature.

If you need an air temperature probe with a fast response time, your best choice would be the exceptionally fast temperature probe 0602 0493 which has a large measuring range.

• TC Type K temperature probe with exceptionally flat cable, which can be pushed through narrow openings, e.g. through slits in doors
• Temperature measurement in pastes and semi-solid media and also in liquids and air
• Measuring range: -40 to 428 °F (-40 to +220 °C)

Includes:

1 x TC Type K temperature probe with penetration tip 0572 9001, can be connected to the testo Saveris 2-T3 Wi-Fi data logger

Measuring Range: -20 to +70°C, 0 to 100 %RH

Measuring Range: -0 to +40°C, 0 to 100 %RH

0554 2005 Extension Cable 2.5m for 2.5mm Clince by Testo

Extend the distance of a testo digital probe (Temperature and Humidity, Lux and UV, or Lux) to a testo 160 Wi-Fi data logger with this 8.2 ft (2.5 m) extension cable.

• Cable length 8.2 ft / 2.5 m
• Extend the reach of digital probes
• Multiple cables can be combined (up to a length of 32.8 ft. / 10 m)

Includes:

1 extension cable for digital probes (length 8.2 ft / 2.5 m)

Measuring Range: -22 to +194°F

0572 2158 External Lux Probe for Testo 160 E and 160 THE Wi-Fi Data Loggers by Testo

The probe is supplied with a connecting cable (length 0.6 m) and if required, longer (8.2 ft. / 2.5 m) extension cables can be added. Multiple cables can be combined up to a length of 32.8 ft. / 10 meters.

Applications for the lux probe

The Lux probe is applicable to exhibits where the light sensitive paintings, fabrics or papers must have logs of their cumulative exposure.

Smart probe calibration

The Lux probe offers maximum digital measurement reliability. As the processing of measuring values is done within the probe, the quality of the measurement is not affected by the length of the cable between the Wi-Fi data logger and the probe. The probe can be sent in for calibration on its own (without the data logger) because the calibration points are stored internally.

• Designed to be non-noticeable with exhibits or display cases
• Illuminance measurement range 0 to 20,000 Lux
• Connects to Wi-Fi logger with extension cables
• External probe for the testo 160 E and 160 THE Wi-Fi data loggers

Includes:

1 x Lux probe with plug-in cable (length 1.7 ft. / 0.6 m) and factory calibration document.

Measuring Range: -50 to +400 °C

0572 1767 176 P1 5-Channel Temperature/RH/Pressure Logger with Internal Absolute Pressure Sensor and External Connection for temp/RH probe by Testo

When the ambient conditions, for example in a laboratory, need to be documeted securely and highly accurately, then the testo 176 P1 is the right data logger. It has an internal absolute pressure sensor and connection possibilities for two external humidity probes.

• Waterproof according to IP 54
• integrated USB and SD card interface for reading out data
• Highly accurate and secure documentation of the ambient conditions e.g. in a laboratory
• Internal absolute pressure sensor and connection possibility for two external humidity probes

0554 2004 Extension Cable 0.6m for 2.5mm Clince by Testo

Extend the distance of testo digital probe (Temperature and Humidity, Lux and UV or Lux) to testo 160 Wi-Fi data logger with the 1.96 ft. / 0.6 m extension cable.

• Cable length 1.96 ft. (0.6 m)
• Extend the reach of digital probes
• Multiple cables can be combined (up to a length of 32.8 ft. / 10 m)

Includes:

1 x extension cable for digital probes (length 1.96 ft. / 0.6 m)

0572 2156 External Temperature and Humidity Probe for Testo 160 E and 160 THE Wi-Fi Data Loggers by Testo

Normally, it is difficult to hide the data logger inside the display cabinet. The testo digital temperature / humidity probe (1.5" x 0.63" / 36 x 16 mm) can be hidden within the case base showing only a small paintable vent cap and the bushing's collar. The data from the probe transfer to the Wi-Fi logger over a thin 1.7 ft. / 0.6 m or an 8.2 ft. / 2.5 m extension cable. The maximum length of combined extension cables is 32.8 ft. / 10 meters.

Applications for the temperature and humidity probe

The temperature and humidity probe is ideal for use in museums, galleries and other exhibit application. Use the high-precision temperature and humidity probe (with external data logger) to measure the temperature and relative humidity in display cabinets. The supplied base plate bushing with an O-ring prevents leakage of external air. Monitor the micro-climate in your display cabinet to see if the artwork maintained at optimal environmental conditions, or if the silica gel pellets need replacing.

Smart probe calibration

The temperature and humidity probe offers maximum digital measurement reliability. As the processing of measuring values is done within the probe, the quality of the measurement is not affected by the length of the cable between the Wi-Fi data logger and the probe. The probe can be sent in for calibration on its own (without the data logger) because the calibration points are stored internally.

• Tiny temperature and humidity probe for use in display cases
• Doesn't effect the air exchange rate in the display case thanks to the wall bushing with an O-ring seal
• "Smart probe" holds internal calibration points
• Measurement range: 0 to 100% relative humidity; temperature 14 to 122 °F (-10 to +50 °C)

Includes:

1 x temperature and humidity probe with plug-in cable (length 1.7 ft. / 0.6 m), base plate mount bushing, and factory calibration document.

Measuring Range: -60 to +400 °C

0572 1560 174T Mini Temperature Data Logger, 1 channel, includes locking wall holder & batteries by Testo

The mini data logger for temperature, testo 174T, is ideal for accompanying transports. Simply positioned close to the goods, e. g. in containers and refrigerated rooms, the data logger monitors temperature continuously, securely and unobtrusively. The free software ComSoft testo 174 allows fast programming of the data logger and easy analysis.

• High data integrity, even with empty battery
• Large measurement data memory
• Watertight in accordance with IP65
• Compact and robust
• Conforms to EN12830
• Issue of alarms via display
• Data transfer to the PC via USB interface
• Reliable temperature measurement for the monitoring of cold chains and sensitive goods during storage and transport
• Easy readout of data and transfer to a PC via Testo USB interface

Measuring Range: -20 to +70°C

0572 1765 176 H1 4-Channel Temperature/RH Logger with 2 External Connections for temp-humidity probes (NTC/capacitive) by Testo

When short-term measurements show no anomalies, but the storeroom climate still does not meet the desired requirements, then the testo 176 H1 is the right data logger. It has two connections for external humidity probes which can be positioned in the room according to the individual requirements.

• Waterproof according to IP 65
• integrated USB and SD card interface for reading out data
• Large memory for 2 million measurement values - large, easily legible display
• Parallel temperature and humidity measurement
• Various connectable humidity and temperature probes e.g. for monitoring humidity in storerooms

Measuring Range: -200 to +1000°C