Test Products International

1010A Indoor Air Quality Meter by Test Products International

Measure ambient CO2, temperature, relative humidity, dew point, wet bulb, CO, and calculate percentage outside air. The TPI 1010A Indoor Air Quality (IAQ) Meter is a state of the art, easy to use tester designed to provide you with the necessary measurements to monitor and make adjustments to air handling devices.

The 1010A IAQ meter uses state of the art sensors to measure humidity, carbon dioxide (CO2), and temperature. The instrument is ruggedly constructed and comes with a 3 Year unit and 2 Year sensor Guarantee.

Features

• Calculate percent outside air to maintain acceptable CO2 levels in buildings and work spaces
• Measure and display Carbon Dioxide (CO2) and Carbon Monoxide
• Measure ambient air temperature
• Measure relative humidity, dew point and wet bulb
• Log up to 10,000 readings in 1 second to 1 hour intervals
• Download to a computer using the A368 USB cable
• Print via I/R to optional printer (Model A740)

Applications

• Check ambient CO and CO2 levels in work and living spaces
• Monitor results of air control systems
• Ambient air temperature and humidity
• Test dew point and wet bulb humidity

Standard Accessories

• TPI 1010A Instrument
• Protective Rubber Boot (A800)
• Soft Carrying Case (A921)
• USB Cable & Software (A803)
• Instruction Manual

Optional Accessories

• Power adapter / Battery eliminator (A804)
• Magnetic strap kit to hang meter (A127)
• Boot hook to hang meter (A103)
• Replacement Software only (A802)
• Replacement USB cable only (A801)

A256 AC/DC Amp Current Probe Adapter by Test Products International

Most TPI brand and any competitor DMM, clamp-on or oscilloscope having the capability of measuring up to 2000mV AC/DC (2V AC/DC), 10M Ohm input impedance, and equipped with industry standard spaced input jacks 19mm on center.

317C Calibratable Pocket Digital Thermometer with Air Tip by Test Products International

TPI's Pocket Digital Thermometers measure temperatures accurately and affordably. All "C" Version Pocket Digital Thermometers can be field calibrated in 32°F ice water to ±2°F!

Features

• Air tip
• Field calibrateable to ±2°F
• Rugged and waterproof (IP63)
• 3.1mm stem for "Pete's" plug
• Auto off
• -Magnetic clip perfect for air duct applications
• 3-year limited warranty

Application

• Ambient air
• Calibrate thermostats
• Vents
• Compressor heads
• Registers
• Grill and surface temperatures
• Serving temperatures

621C3 Dual Input Differential Manometer Kit by Test Products International

Differential input high resolution manometer with A612 protective boot, two A603 1/8" barbed NPT fittings, two A605 1/8" barbed T fittings, two A776 static tips, and A908 carrying case with shoulder strap.

The TPI 621C3 is a hand held pressure meter with superior resolution.

All of these models measure over the range of -40.0 to +120.0 mbar. Each unit has a resolution of 0.01 mbar to +19.00 mbar and automatically auto-ranges above ± 19.00 mbar to 0.1 mbar resolution. Each model is supplied complete with carry pouch, battery and instruction manual.

The 621C3 includes all of the specs of the Model 621 and additionally consists of the following:

• 621 Manometer: + A612 Boot with tilt stand
• A605 T Fitting (x2): Ideal for use on setting pressure switches
• A776 Static Tip (x2): Measure static pressure with A776. It has a magnet to secure in place in duct work 1/4" hole required to use
• A774 Tubing: 6 foot length of silicone tubing for pressure measurements. Very flexible and will not go hard in cold temperatures.
• A791 Adapter Tube: Flexible tubing for connecting to larger fittings
• A908 Carrying Case: Soft padded case with shoulder strap holds the thermometer and probes.

708C5 708 Combustion Efficiency Analyzer Kit by Test Products International

708 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature

270 Features

• Measure motor in-rush current and run current
• Measure temperature differential with relative mode
• Non-contact voltage feature can be used to immediately see if power is being supplied to the 24VAC control circuit of thermostats
• Frequency, Min/Max/Record, Data Hold and Peak Hold
• Up to 40,000 Microfarads to test run and start capacitors
• 4,000 count display with 41 segment analog bargraph
• Auto & Manual Ranging
• Low Battery Indicator
• Over Range Indication ("OL")
• Hi Voltage Indicator (>30V AC/DC)
• Auto Power Off after 30 minutes
• Separate Battery/Fuse Compartment
• Low Ohm Range (400V)
• Amps AC Resolution: 0.01A
• VDC/VAC Resolution: 0.1mV
• DC μA measurement (0.01 μA resolution)
• Temperature measurement with 0.1° resolution

Includes

• 708 Combustion Efficiency Analyzer
• 270 Clamp-On Tester with Digital Multimetervisit

TPI-1200 BNC Attenuator Kit by Test Products International

Includes

• 805-53-000 BNC Shunt
• 120082 Individual BNC Attenuator, 3 dB 1.0 Watt
• 120083 Individual BNC Attenuator, 6 dB 1.0 Watt
• 120085 Individual BNC Attenuator, 20 dB 0.5 Watt
• 105-52-000 BNC Termination

50 AC Safety Volt Check 50-1,000 Volts AC with Audio and Visual Alert by Test Products International

TPI AC Volt Testers. Determine the presence or absence of AC voltage without disconnecting the system in question.

The AC Volt 50 is a hand held device for determining the presence or absence of AC voltage in insulated wires, wall receptacles, fuses, junction boxes, switches, and any other voltage carrying electrical system. It is not necessary to disconnect the system in question because no contact is required for operation and current flow is not necessary to locate voltage. Simply touch the plastic tip to a connection point or move it along an insulated wire. If AC voltage is present, The AC Volt 50 will sound an audio alert and an LED light in the probe tip will glow bright red. The illumination will stop at a break in the circuit or wire, and this allows the AC sensor to be used as a troubleshooting instrument.

Features

• Prevent electrical shocks
• Non-contact detection of 50 to 1,000 VAC
• Troubleshoot electrical circuits
• No switch required. Always ready for use. Competing products require an ON/OFF switch
• Audible buzzer and visual alarm, red glow indicates presence of 50-1,000 V
• Uses 2 AAA batteries Common and inexpensive. Competing producs require more expensive camera batteries
• Lifetime warranty
• UL listed

Applications

• Wires
• Wall Receptacles
• Fuses
• Junction Boxes
• Switches
• Defective Grounds
• Any other Voltage
• Carrying Electrical System

P250 Non-Switchable Passive Oscilloscope Probe, 250MHz, 1.2M Cable Length by Test Products International

Selecting the correct oscilloscope probe ensures accuracy and can improve the performance of your test instrument. TPI offers a wide range of high quality oscilloscope probes designed to meet the most demanding applications.

The IP series monolithic probes have switchable attenuation and are available in 60 and 250MHz. These probes are ideal for technicians that need a basic oscilloscope probe.

The slimline design P and SP series probes are available in fixed or switchable attenuation. These series of probes are perfect for the technician needing additional features such as replaceable cable and interchangeable probe tip. The compensation adjustment for these probes is located in the BNC to eliminate noise pickup.

TPI also offers three models of high voltage differential probes all with high common mode rejection, wide bandwidth, and fast rise times. Differential probes enable the viewing of signals not referenced to earth ground and provide better performance than a matched pair of single ended oscilloscope probes when measuring these types of signals.

Several important factors must be taken into account when selecting the proper probe.

• The probe should have sufficient bandwidth and rise time for the test instrument and application. Choose a probe with at least an equal bandwidth as the scope it will be used with. For best performance a probe with twice the bandwidth as the scope should be selected
• For oscilloscope probes, the input capacitance of your oscilloscope should be within the compensation range specification of the probe. In addition, if your oscilloscope has readout function, select a probe with this capability
• For differential probes, make sure the maximum differential voltage is adequate for your application and the common mode rejection specification meets the requirements of the tests being performed.

Features

• Attenuation: Ratio of the output signal to the input signal. Attenuation should remain constant decreasing by 3dB only as the frequency increases to the maximum bandwidth.
• Bandwidth: The maximum -3dB frequency that can be expected.
• Cable Length: Length of the cable from the end of the probe to the end of the connector. It is important to use a probe with just enough cable length for your needs. Long cables increase the capacitance and propagation delay of the probe.
• Compensation Range: The range a probe can be compensated to match the input capacitance of the test equipment it is being used with.
• IEC 1010: Probes with the IEC 1010 category rating have been designed for safety.
• Input Impedance: The total resistance and capacitance as measured at the tip of the probe. This specification is used to define the loading effect of a probe. At frequencies under 1MHz the input resistance of the probe will have the most influence. At higher frequencies the input capacitance will have the most influence.
• Max Input Voltage: The maximum voltage the probe can be used at.
• Max Differential Voltage: The maximum differential voltage that can be measured by a differential probe
• Readout: Probes with this capability are compatible with readout function oscilloscopes that automatically detect and display the attenuation factor of the probe.
• Rise Time: The time required for the leading edge of a pulse to rise from 10% to 90% of its final value.
• CMRR: Common Mode Rejection Ratio. A measure of a differential probes ability to reject any signals common to both test points in a differential measurement

Applications

• Use TPI Probes with Bench Top, Portable, Analog, and Oscilloscopes
• Logic signal and waveform tests
• Measure voice / data signals
• Analyze power quality
• Test motor control circuits

Markets

• Electronic
• Communication
• Commercial
• Industrial

737K1 Purge Probe Kit by Test Products International

Meets the requirements for latest NFPA 54 fuel gas purging requirements for large gas systems.

Measure combustible leaks, LEL and %volume

Provides personal protection from potential hazardous conditions and help find the source of combustible gases fast!

Features

• Internal Pump
• Water/Dust Filter
• Push Button Operation
• Field Calibration
• Date/Time Display
• Calibration Alert
• Operation Memory
• Calibration Memory
• Infrared Download
• Audible/Visual Alarms
• Backlit LCD
• Programmable Auto Shut Off

Applications

• Gas Leak Survey/Investigations
• Confined Space Monitoring
• Gas Emergency Investigations
• Vessel Testing

The 737K1 Purge Probe Kit includes the following:

• 737
• Carry pouch
• Instruction manual
• A758 purge probe
• Batteries
• Extra water/dirt filter trap

TPI-3000A Universal Cables & Connector Kit by Test Products International

TPI-3000A Universal Cables & Connector Kit. Technicians and engineers turn to TPI for their connecting needs. With the TPI-3000A and TPI-5000A kits, technicians can create connections on the spot in seconds.

Features

• Includes 8 types of connectors for male and female adapters
• Simply screw on any combination of 24 connectors to any of the six universal interfaces with no soldering or crimping needed
• Reusable connectors can be used over and over in different combinations to fit and assist customizing the installation
• Works with universal cables GEX-60 (36"), GEX-48 (48"), and GEX-75 (72")
• Connector bodies are silver-plated machine brass with PTFE insulation
• Zippered soft case protects and organizes the individual pieces

708C8 708 Combustion Efficiency Analyzer Kit by Test Products International

708 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature

Includes

• 708 Combustion Efficiency Analyzer
• 621 Dual Differential Input Manometer
• Two 605 Single Input Digital Vacuum Gauge
• A774 Silicone Pressure Tubing
• Two A776 Static Tip

707A740 707 Carbon Monoxide Analyzer Kit by Test Products International

A707 Features

• Clear and fast response with advance pump driven technology
• Peak Hold to capture peak CO reading
• Instrument recycles and will not shut off if 15ppm CO is present, increasing safety
• Store Button allows you to save up to eight readings and then print using the IR port and optional A740 printer
• 1 ppm sensitivity
• Measures up to 10,000ppm
• Push on fittings are fast and easy to use
• Large easy to read backlit display
• Advanced electrochemical sensor is field replaceable and calibrateable
• Protective rubber boot and soft carrying case with shoulder strap is included
• Pump driven
• Pump flow block indicator
• Auto zero

A740 Features

• Power On indication (red LED)
• Adjustable contrast (low, norm, high)
• Manual paper feed (advance)
• Operates on 4 "AA" batteries or optional AC adapter
• Self test at Power On
• 3-Year Warranty

58-036-1A RG58/U, BNC Male to BNC Male, 36 inch by Test Products International

50 Ohm, 75 Ohm, 93 Ohm. TPI BNC to BNC coax cable assemblies include: RG58/U (molded and assembled), RG59/U and RG62/U.

Features

• UL Listed Cable: Ensures quality and consistency in the cable construction.
• Boot is molded to cable connector for added strength: Limits the amount of bending the cable is exposed to at the connector to prevent cable breakage.
• Gold center pins: Ensures that there is a high quality connection maintaining the best return loss in high definition applications.
• Machined Brass Connectors: Unlike die-cast connectors, machined brass connectors have more precise tolerances, strength and positive mating meaning low signal loss for precise video and data applications.
• Boot is molded to cable connector for added strength
• 95% shielding
• 80°F temperature rating
• Multiple lengths up to 100 feet
• Individually bagged

265 Clamp-On Tester with Frequency and Capacitance by Test Products International

Perfect for tight, narrow, spaces. The new TPI 265 with slim jaw and body is ideal for cramped work areas and crowded electrical panels.

The 265 is a hand-held, autoranging clamp-on DMM. Extra large numerals, capacitance, frequency and data hold are just a few of the features of the 265. An affordable choice, the 265 offers measurements in all basic electrical functions.

Features:

• Slim jaw and body design for use is crowded electrical panels
• 4,000 count display
• Capacitance range up to 4,000 microfards to test run and start capicitors
• 0.1 DC millivolt resolution to accurately measure thermocouples and use optional adapters
• 0.01 AC Amp resolution to measure heat anticipator current
• Frequency measurement capability
• AC/DC volts up to 600V and AC Amps up to 400A
• Diode, resistance and audible continuity ranges
• Auto / manual ranging
• Data hold
• Auto power off
• CAT III 600V rated
• cULus 61010
• 3-year limited warranty

Applications:

• Test start and run capacitors
• Measure heat anticipator current
• Determine thermocouple voltage
• Test line and control voltages
• Measure heating element resistance
• Measure and adjust variable frequency drives

The 265 comes complete with the following accessories:

• Carrying Pouch
• Test Lead Set
• Instruction Manual
• Battery

HXG-3 Combustible Gas Leak Detector by Test Products International

The HXG-3 offers 10ppm sensitivity to detect combustible gasses. Easily operated with new patent pending electronic tick control, leaks are pinpointed using the audio and visual indicators. Two line backlit LCD displays gas leaks in ppm and %LEL simultaneously.

Pinpoint Leaks

Leaks can easily be pinpointed by using an audible tick rate. The sensor is located at the end of a flexible gooseneck to easily reach areas where leaks may be suspected.

Data Save

A Data Save feature allows you to save data during any investigation.

Features

• Combustible Gas Leak Detector capable of displaying ppm or %LEL (Lower Explosive Limit).
• UL 913 intrinsic safety rating
• 10 ppm sensitivity (methane)
• Instant response
• Electronic tick rate control
• Settable alarm
• Visual and audible leak indication
• 16'' gooseneck
• Hard carrying case
• Displays LEL and PPM
• Infrared Downloading
• Long-life, Low-Cost Sensor
• Simple Calibration

Applications

• Confined Space Monitoring
• Vessel Testing
• Manhole Entry
• Vault Entry
• Leak Detection
• Leak Pinpointing
• Pipeline Purging

Partial List of Industries:

• Natural Gas Companies
• Propane Suppliers
• Electric Companies
• Safety Engineers
• Fire and Police
• Emergency Vehicles
• Appliance Repair
• Plant Maintenance
• Plumbing Contractors
• Marine Operations
• Heating and Air Conditioning
• Municipalities
• Mobile Home Parks
• Apartment Buildings

341KC2 Single Input K-Type Thermocouple Thermometer with GK11M Probe by Test Products International

TPI contact temperature testers are accurate, reliable, and built to last. Models 341K, 343 and 367D can be auto field calibrated to system accuracy (tester plus probe) of ± 1°F in less than 10 seconds in ice water.

Auto Field Calibration Perform ice bath calibration to achieve ±1°F system accuracy within the 30°F to 120°F temperature range. Calibration is an easy two-step process performed with instrument keypad, no additional tools needed.

Features:

• Auto Field Calibrate in less than 10 seconds in ice water to achieve ± 1°F system (tester & probe) accuracy within 30°F to 120°F temperature range
• Min / Max Record
• Auto Resolution (0.1° / 1°)
• °C/°F Selectable
• Hold feature freezes reading on display
• Auto Off
• Protective rubber boot
• Easy to read LCD display

Includes:

• GK13M temperature probe
• A304 protective boot
• A255 soft pouch