$500 - $750, Test and Measurement

SCT-108.002.07 SCT-BUD Portable pH/ORP/DO Meter by ScichemTech

Includes:

• Plastic pH/ATC three-in-one combined electrode
• Do electrode
• pH standard buffer solution
• Membrane cap
• Do electrode inner solution
• Cathode polishing paper
• Screw driver
• Spare batteries
• Operation manual
• Carrying case.

Features:

• A complete portable SCT-meter for pH, ORP and dissolved oxygen measuements.
• Built-in microprocessor chips, intelligent functions such as automatic calibration, automatic temperature compensation, data storage, function set-up, self-diagnose information, automatic power-off and low voltage display.
• Double-parameter meter, equipped with ph electrode and dissolved oxygen electrode, automatic identification of electrode by meter.
• Automatic identification of 12 pH standard buffer solutions, three options of Standard buffer solutions: Europe and America series & nist series.
• Able to set pH measurement modes of high purity water and pure water with Ammonia.
• Measurement mode of dissolved oxygen has the function of automatic temperature compensation, automatic salinity compensation and manual air pressure compensation.
• New polarographic type dissolved oxygen electrode can measure temperature, salinity and dissolved oxygen simultaneously, equipped with special dissolved oxygen electrode calibration set, polarization only for 3~5 min.
• SCT meter meets ISO9001:2000, ce standards and water proof IP57.

SCT-108.002.09 SCT CADY pH/ORP/Conductivity/TDS/Salinity/Resistivity/Temp Meter by ScichemTech

Includes:

• Plastic pH/ATC three-in-one combined electrode
• Plastic ORP combined electrode
• Plastic conductivity electrode
• pH standard buffer solution
• 1413us/cm conductivity standard solution
• Screw driver
• Spare batteries
• Operation manual
• Carrying case

Features:

• A complete portable SCT-meter for ph, ORP and conductivity measurements.
• Multi-parameter meter, equipped with ph electrode, ORP electrode and conductivity electrode, automatic identification of electrode by meter.
• Built-in microprocessor chips, intelligent functions such as automatic calibration, automatic temperature compensation, data storage, function setup, self-diagnose information, automatic power-off and low voltage display.
• Automatic identification of 12 ph standard buffer solutions, three options of standard buffer solutions: Europe and America series & nist series
• Able to set pH measurement modes of high purity water and pure water with ammonia.
• Automatic identification of 7 conductivity standard calibration solutions, two options of standard calibration solutions: Europe and America series.
• Adopt advanced conductivity measurement technology, use conductivity electrode of constant k=1, only need one point calibration and meet the measurement precision requirement of 0.5μs/cm ~ 200 ms/cm.
• Ability to switch among conductivity, TDS, salinity and resistivity. Multinomial calculation for TDS and salinity to ensure the conversion precision of the full scale.
• Conductivity measurement mode has the function of non-linear temperature compensation for high purity water.
• SCT meter meets ISO9001:2000, CE standards and water proof IP57.

SCT-108.002.12 SCT CHRIS Water Hardness Meter by ScichemTech

Includes:

• Water hardness electrode (with two measuring heads and one screw plug)
• Cell (1.5v)
• 100ml hardness calibration solution (B1, B2 and B3)
• 20ml test cup
• Test cup pedestal
• Reference solution
• Tools for filling reference solution
• Carrying case
• Operation manual

Features:

• A complete portable SCT-meter for calcium and magnesium, ions hardness measurements.
• Portable meter for measurement of water hardness (the total concentration of calcium ion and magnesium ion).
• Electrode adopts water hardness combination electrode with patent structure. It consists of measurement electrode, reference electrode and temperature probe. Replaceable measuring head, steady potential, fast response, easy to use.
• Meter adopts intelligent chip design, automatic calibration, automatic temperature compensation, time display, data storage, low voltage display, etc.
• Ability to switch among eight units: MMOL/L, MG/L (CACO3), MG/L (CAO), MMOL/L (Boiler), MG/L (CA). Three options of three units: ºFH France ºDH Germany and ºEH, UK from WH-link communication software.
• Equipped with B1, B2 and B3 calibration solution.
• SCT meter meets ISO9001:2000, CE standards and water proof IP57.

SCT-108.002.32 SCT LESA IR Thermo Anemometer by ScichemTech

Includes:

• 9V battery
• Instruction manual
• Carrying case
• USB cable
• PC interface
• Window based software

Features:

• A complete portable SCT meter for air velocity, air flow and temperature measurements.
• Simultaneous display air flow in CFM/CMM or air velocity plus ambient temperature
• Combination of hotwire and standard thermistor, deliver rapid and precise measurements event at low air velocity
• Infrared thermometer measures remote surface temperature to 999F (537C) with 30:1 distance to spot ratio and laser pointer
• Wide range measurements of air velocity, fast response time
• Multifunction for air flow measurements : m/s, km/h, ft/ min, knots, mile/h
• Super large LCD with dual function display, read the air velocity and temperature at the same time.
• Ac power operated.

SCT-108.003.03 SCT BE-pH-3 Benchtop pH/ORP/Temp Meter by ScichemTech

SCT basic benchtop ph/ORP/temp meter with ATC and with RS232 suitable for general pH measurement in laboratory.

Equipped with plastic 3 in 1 pH combination electrode and stirring type electrode holder easier to use.

Automatic calibration, automatic temperature compensation Instrument with pH resolution 0.01.

Includes:

• Plastic pH combination electrode
• Temperature electrode
• pH 4.00,7.00,10.01 (50 ml) standard solution
• 9V power adapter
• Stirring type electrode holder
• pH link communication software
• RS232 communication cable
• Operation manual.

Features:

• SCT benchtop meter is designed to measure pH/ORP/temperature.
• Large LCD with blue background can display both pH and temperature value at the same time.
• It has intelligent functions for automatic calibration, automatic temperature compensation, data storage/recall, and memory max. and min. value etc.
• 1~3 point automatic calibration, and it can automatically display the percentage of slope after finishing calibration
• Equips tempearature electrode and stirring type electrode holder, which is more suitable for using.
• °C and °F can be switched freely.
• SCT benchtop meter meets: ISO9001 & CE standards

SCT-108.003.04 SCT BEN-pH-4 Benchtop GLP pH Meter by ScichemTech

SCT (GLP) good laboratory practice benchtop pH/ORP/Temp meter suitable for routine laboratory use.

Equipped with flexible electrode holder & quick operation guide easier to use.

Instrument rating 0.01.

Includes:

• Flexible electrode holder
• pH/ATC three-in-one combination electrode
• pH standard buffer solution 4.00, 7.00, 10.01(50 ml)
• 9v power adapter
• RS-232 communication cable
• Communication software CD
• Operation manual
• Packing list

Features:

• SCT meter meets with the requirement of international GLP standards. Its features up to automatic calibration, automatic temperature compensation, data storage, timing measurement, clock display, RS-232 output, function setting and self-diagnose etc.
• Three different measurement modes: stable display mode; time measurement mode; continuous measurement mode.
• Automatically recognize pH buffer solution. User can choose anyone from three series of standard buffer solutions: Europe & USA series, & NIST series
• SCT dustproof and waterproof meter meets IP54 standards. All sockets are seal protected by the silica gel caps.
• SCT benchtop meter meets: ISO9001 & CE standards

1008A Indoor Air Quality Meter by Test Products International

Measure and display carbon dioxide (CO2) and temperature. The TPI 1008A Indoor Air Quality (IAQ) Meter is a state of the art, easy to use tester designed to provide you with the necessary measurements to monitor and make adjustments to air handling devices.

The 1008A IAQ meter uses state of the art sensors to measure carbon dioxide (CO2), and temperature. The instrument is ruggedly constructed and comes with a 3 Year unit and 2 Year sensor Guarantee.

Features

• Measure carbon dioxide (CO2) and temperature simultaneously
• Record and display min, max & average
• Store up to 50 readings in memory in 1, 2, 3, 5, 10, 20, 30, 40, 50, 60 min intervals
• Print via I/R to optional printer (Model A740)

Applications

• Check ambient CO2 levels in work and living spaces
• Ambient air temperature

Standard Accessories

• TPI 1008 Instrument
• Protective Rubber Boot
• Soft Carrying Case (A921)
• USB Cable & Software (A803)
• Instruction Manual

Optional Accessories

• Power adapter / Battery eliminator (A804)
• Magnetic strap kit to hang meter (A127)
• Boot hook to hang meter (A103)
• Replacement Software only (A802)
• Replacement USB cable only (A801)

707A740 707 Carbon Monoxide Analyzer Kit by Test Products International

A707 Features

• Clear and fast response with advance pump driven technology
• Peak Hold to capture peak CO reading
• Instrument recycles and will not shut off if 15ppm CO is present, increasing safety
• Store Button allows you to save up to eight readings and then print using the IR port and optional A740 printer
• 1 ppm sensitivity
• Measures up to 10,000ppm
• Push on fittings are fast and easy to use
• Large easy to read backlit display
• Advanced electrochemical sensor is field replaceable and calibrateable
• Protective rubber boot and soft carrying case with shoulder strap is included
• Pump driven
• Pump flow block indicator
• Auto zero

A740 Features

• Power On indication (red LED)
• Adjustable contrast (low, norm, high)
• Manual paper feed (advance)
• Operates on 4 "AA" batteries or optional AC adapter
• Self test at Power On
• 3-Year Warranty

708A740 708 Combustion Efficiency Analyzer Kit by Test Products International

708 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature

A740 Features

• Easy to use
• Battery operated
• Self test facility
• Adjustable contrast
• Manual paper feed
• Maximum transmitting distance 16"(45cm)

708C5 708 Combustion Efficiency Analyzer Kit by Test Products International

708 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature

270 Features

• Measure motor in-rush current and run current
• Measure temperature differential with relative mode
• Non-contact voltage feature can be used to immediately see if power is being supplied to the 24VAC control circuit of thermostats
• Frequency, Min/Max/Record, Data Hold and Peak Hold
• Up to 40,000 Microfarads to test run and start capacitors
• 4,000 count display with 41 segment analog bargraph
• Auto & Manual Ranging
• Low Battery Indicator
• Over Range Indication ("OL")
• Hi Voltage Indicator (>30V AC/DC)
• Auto Power Off after 30 minutes
• Separate Battery/Fuse Compartment
• Low Ohm Range (400V)
• Amps AC Resolution: 0.01A
• VDC/VAC Resolution: 0.1mV
• DC μA measurement (0.01 μA resolution)
• Temperature measurement with 0.1° resolution

Includes

• 708 Combustion Efficiency Analyzer
• 270 Clamp-On Tester with Digital Multimetervisit

708C7 708 Combustion Efficiency Analyzer Kit by Test Products International

708 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature

270 Features

• Measure motor in-rush current and run current
• Measure temperature differential with relative mode
• Non-contact voltage feature can be used to immediately see if power is being supplied to the 24VAC control circuit of thermostats
• Frequency, Min/Max/Record, Data Hold and Peak Hold
• Up to 40,000 Microfarads to test run and start capacitors
• 4,000 count display with 41 segment analog bargraph
• Auto & Manual Ranging
• Low Battery Indicator
• Over Range Indication ("OL")
• Hi Voltage Indicator (>30V AC/DC)
• Auto Power Off after 30 minutes
• Separate Battery/Fuse Compartment
• Low Ohm Range (400V)
• Amps AC Resolution: 0.01A
• VDC/VAC Resolution: 0.1mV
• DC μA measurement (0.01 μA resolution)
• Temperature measurement with 0.1° resolution

A740 Features

• Easy to use
• Battery operated
• Self test facility
• Adjustable contrast
• Manual paper feed
• Maximum transmitting distance 16"(45cm)

Includes

• 708 Combustion Efficiency Analyzer
• 270 Clamp-On Tester with Digital Multimetervisit
• A740 IR Printer

708C8 708 Combustion Efficiency Analyzer Kit by Test Products International

708 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature

Includes

• 708 Combustion Efficiency Analyzer
• 621 Dual Differential Input Manometer
• Two 605 Single Input Digital Vacuum Gauge
• A774 Silicone Pressure Tubing
• Two A776 Static Tip

708OIL 708 Combustion Efficiency Analyzer Kit by Test Products International

708 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature

Includes

• 708 Combustion Efficiency Analyzer
• A788 Smoke Test Pump

709 Combustion Efficiency Analyzer and Differential Manometer by Test Products International

The carbon monoxide sensor used in TPI combustion efficiency analyzers feature an on-board filter capable of filtering NO (nitric oxide), NO₂ (nitrogen dioxide) and NOX (combination of NO and NO₂) to prevent cross sensitivity errors.

Use TPI analyzers to test flue gases in gas and oil fired equipment including high efficiency furnaces and condensing boilers. Measure CO, O₂, and stack temperature.

Determine combustion efficiency, CO₂, and CO air free. Built-in differential manometer, combustible gas detection, PC communication, data logging, and can measure NO / NOX.

Features

Using TPI analyzers to determine combustion efficiency at the time of equipment set up minimizes call backs and can be used to verify to the home owner the value of service work by showing the increase in equipment efficiency after work is performed. Efficiency calculation can also be used to generate business by demonstrating the need to improve the efficiency of equipment or to show the benefit of purchasing new equipment with higher efficiency.

Quick And Simple Set Up

All TPI analyzers feature quick and simple set up. Fast purge and the ability to perform fuel selectionduring start up enable tests to be performed quickly without requiring extra set-up time after initial startup. TPI analyzers also use the last selected fuel as the default setting. This feature prevents the need toperform fuel selection every time the analyzer is turned on.

• High resolution 0.001 in H20 differential manometer for high efficiency and oil equipment
• Measure CO, and temperature
• Calculate CO2, efficiency, excess air, and CO air free
• Pump driven for fast response
• Will not shut off if 15 ppm CO is present for increased safety
• Ten selectable fuels: Natural Gas, LPG, Light Oil, Heavy Oil, Bituminous Coal, Anthracite Coal, Coke, Butane, Wood, Bagasse
• Optional A740 IR printer available for hard copies of test results
• Built-in differential thermometer
• Store function to save up to 50 readings
• Large easy to read backlit display

Applications

• Tuning of residential and furnaces and domestic boilers
• Ambient and stack testing for CO
• CO safety measurements in and around combustion sources
• Temperature checking, including superheat and hydronic differential temperatures
• Dual input differential manometer

709A740 709 Combustion Efficiency Analyzer Kit by Test Products International

709 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature
• Dual input pressure with 0.001 inches water resolution for high efficiency & oil

A740 Features

• Easy to use
• Battery operated
• Self test facility
• Adjustable contrast
• Manual paper feed
• Maximum transmitting distance 16"(45cm)

709A740 709 Combustion Efficiency Analyzer Kit by Test Products International

709 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature
• Dual input pressure with 0.001 inches water resolution for high efficiency & oil

A740 Features

• Easy to use
• Battery operated
• Self test facility
• Adjustable contrast
• Manual paper feed
• Maximum transmitting distance 16"(45cm)

A773

Use the A773 when working on oil fired appliances to extend the life of your sensors by eliminating acid gas exposure to your analyzer

709OIL 709 Combustion Efficiency Analyzer Kit by Test Products International

709 Features

• Fast purge & fuel selection during start up
• Work on high efficiency furnaces and oil
• Measure CO, O2; and calculate efficiency, CO2, excess air and CO air free
• Dual input temperature
• Dual input pressure with 0.001 inches water resolution for high efficiency & oil

Includes

• 709 Combustion Efficiency Analyzer
• A773 Sulfer Filter
• A790 Analog Oil Pressure Gauge
• A788 Smoke Pump Test

709R Combustion Efficiency Analyzer with Differential Manometer by Test Products International

The carbon monoxide sensor used in TPI combustion efficiency analyzers feature an on-board filter capable of filtering NO (nitric oxide), NO₂ (nitrogen dioxide) and NOX (combination of NO and NO₂) to prevent cross sensitivity errors.

Use TPI analyzers to test flue gases in gas and oil fired equipment including high efficiency furnaces and condensing boilers. Measure CO, O₂, and stack temperature.

Determine combustion efficiency, CO₂, and CO air free. Built-in differential manometer, combustible gas detection, PC communication, data logging, and can measure NO / NOX.

Features

Using TPI analyzers to determine combustion efficiency at the time of equipment set up minimizes call backs and can be used to verify to the home owner the value of service work by showing the increase in equipment efficiency after work is performed. Efficiency calculation can also be used to generate business by demonstrating the need to improve the efficiency of equipment or to show the benefit of purchasing new equipment with higher efficiency.

Quick And Simple Set Up

All TPI analyzers feature quick and simple set up. Fast purge and the ability to perform fuel selection during start up enable tests to be performed quickly without requiring extra set-up time after initial startup. TPI analyzers also use the last selected fuel as the default setting. This feature prevents the need to perform fuel selection every time the analyzer is turned on.

• High resolution 0.001 in H20 differential manometer for high efficiency and oil equipment
• Measure CO, and temperature
• Calculate CO2, efficiency, excess air, and CO air free
• Pump driven for fast response
• Will not shut off if 15 ppm CO is present for increased safety
• Ten selectable fuels: Natural Gas, LPG, Light Oil, Heavy Oil, Bituminous Coal, Anthracite Coal, Coke, Butane, Wood, Bagasse
• Optional A740 IR printer available for hard copies of test results
• Built-in differential thermometer
• Store function to save up to 50 readings
• Large easy to read backlit display
• Rechargeable Ni-MH Battery with > 6 Hours battery life

Applications

• Tuning of residential and furnaces and domestic boilers
• Ambient and stack testing for CO
• CO safety measurements in and around combustion sources
• Temperature checking, including superheat and hydronic differential temperatures
• Dual input differential manometer

HXG-2D Combustible Gas Leak Detector by Test Products International

The HXG-2D offers 10ppm sensitivity to detect combustible gasses. Easily operated with new patent pending electronic tick control, leaks are pinpointed using the audio and visual indicators. Backlit LCD display of gas leaks in ppm or %LEL.

Features

• Combustible Gas Leak Detector capable of displaying ppm or %LEL (Lower Explosive Limit).
• Designed to meet UL 913 intrinsic safety (Approval Pending)
• 10 ppm sensitivity (methane)
• Instant response
• Electronic tick rate control
• Settable alarm
• Visual and audible leak indication
• 16'' gooseneck
• Hard carrying case

Applications

• Detect combustible gasses including natural gas methane, propane (LPG), gasoline, diesel, and kerosene
• Trace natural gas lines and fittings for leaks
• Check gas generation for leaks

How big is the leak?

• Direct PPM readout
• Direct "LEL" percent readout

Find Leaks Quickly

• New "Patent Pending" electronic tick control
• Ideal for Natural, Propane and Butane gas leaks

Safe, Durable and Reliable

• Intrinsically safe design
• SENSIT "ruggedized" design

Partial List of Industries:

• Utility Companies
• Gas Processing Plants
• Propane Marketers
• Safety Engineers
• Fire and Police
• Emergency Vehicles
• Appliance Repair
• Plant Maintenance
• Plumbing Contractors
• Furnace Heat Exchanger Testing
• Marine Operations
• Heating and Air Conditioning
• Municipalities
• Mobile Home Parks
• Apartment Buildings

6321 Differential Pressure Transmitter - base unit, standard housing plastic by Testo

A differential pressure transmitter with a good price/performance ratio for applications in air conditioning and ventilation technology. The automated building services must always be monitored precisely, whereby the requirements placed on the measuring technology are increased. testo 6321 fulfills these requirements by ensuring the best possible system function, optimization of the climatic conditions and energy savings by means of highly accurate measurement, stable over the long-term, of the differential pressure.

Areas of application:

• Industrial and commercial buildings, e.g. in production and storage
• Offices and administrational buildings
• Sales areas and exhibition halls
• Museums and libraries
• School buildings, hotels, clinics etc.

• Measurement of differential pressure in the measuring range of 100 Pa to 2 bar
• Magnetic valve for automatic zero-point adjustment guarantees high temperature-independent accuracy and long-term stability
• Accuracy ±1.2 % of measuring range + intrinsic error of 0.3 Pa valid for zeroing cycle of 60 sec/nominal temperature +22 °C
• P2A software for parameterization, adjustment and analysis, saves time and costs in commissioning and maintenance
• Freely scalable: ±50% of measuring range final value and free scalability within the measuring range
• Diverse analog outputs and measuring ranges
• Display optional